Osram DALIeco User manual

Attention!: All previous settings will be replaced by the
basic settings Single Office!
Step 1: Activate programming mode
Keep the programming key [5] pressed (>0.5s).
LED [1] starts flashing red.
Step 2: Select mode
Briefly press the Single-Office button [4] (<0.5s).
DALI luminaires flash 1 time.
Step 3: Daylight harvesting - save set value for daylight harvesting automatically –OR–
Activate daylight harvesting by pressing Auto setup [7].
Luminaires dim to 80% and sensor value stored as target light intensity.
Note: Set-up only in the evening/night-time with little or no daylight.
Set-up duration is about 3 min. LED [2] will flash red/green during that period.
Daylight harvesting - save set value for daylight harvesting manually
Set brightness value by pressing the buttons CH-1 [9] up/down.
Confirm by pressing the Manual setup key [10]shortly.
Daylight harvesting will be activated.
DALI luminaires flash 2 times; LED [2] will flash red/green during that period.
Note: Set-up only in the evening/night-time with little or no daylight.
Step 4: Exit programming mode
Briefly press the programming key [5] (<0.5s).
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Basic Settings Single Office:
•Light level of the two DALI channels: 80%
•Power up: By movement, push button or remote control
•Turn off: Automatic, push button or remote control
•Absence Switch-off delay time: 15min.
•Stand-by: Off
•Daylight harvesting: ON (Not active until set value is stored!)
•Offset: +30% for CH-2 (Does not show up until daylight harvesting is dimming CH-1)
Optional settings (individually configurable)
Start with long press (>0.5s) of the programming key [5]. (Start programming mode)
LED [1] starts flashing red.
Absence Switch-off delay time
e.g. Briefly press the 30sec key [3] for a delay time of 30sec.
Note: 1sec test is purely a test function (Do not use)!
Absence Stand-by-level
e.g. Briefly press the 10% key [11] for a 10% brightness of the stored
light
value.
Absence Stand-by delay time
e.g. Briefly press the 30sec key [12] for a 30sec delay time of
Stand-by before switch-off.
Note: Not possible if Stand-by level is set on OFF.
Daylight harvesting activation/deactivation
e.g. Briefly press the Off-button [14] to deactivate daylight harvesting.
Note: Default On (See DALIeco control manual for details).
Use full automatic mode olny in combination with motion detection.
Motion Sensor activation/deactivation
e.g. Briefly press the Off-button [13] to deactivate motion detection.
Note: Default ON (See manual for details).
Exit with short press (<0.5s) of the programming key [5]. (End programming mode)
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Adjust Offset (not adjustable in the programming mode)
- Briefly press the Offset key [6] to start.
- Change Offset level with the CH-2 key [8].
- Briefly press the Offset key [6] to save and end.
Note: Only available in combination with the daylight harvesting.
Offset adjustment of CH-2 only between the CH-1 value and the
stored set value.
Adjust Offset with sufficient daylight only.
Note: Further information on the individual functions and
settings can be found in the DALIeco control user
guide.
DALIeco
Quick Start Guide
Single Office Mode

Attention!: All previous settings will be replaced by the
basic settings Open-plan Office!
Step 1: Activate programming mode
Keep the programming key [5] pressed (>0.5s).
LED [1] starts flashing red.
Step 2: Select mode
Briefly press the Open-plan Office button [4] (<0.5s).
DALI luminaires flash 1 time.
Step 3: Daylight harvesting - save set value for daylight harvesting automatically –OR–
Activate daylight harvesting by pressing Auto setup [7].
Luminaires dim to 80% and sensor value stored as target light intensity.
Note: Set-up only in the evening/night-time with little or no daylight.
Set-up duration is about 3 min. LED [2] will flash red/green during that period.
Daylight harvesting - save set value for daylight harvesting manually
Set brightness value by pressing the buttons CH-1 [9] up/down.
Confirm by pressing the Manual setup key [10]shortly.
Daylight harvesting will be activated.
DALI luminaires flash 2 times; LED [2] will flash red/green during that period.
Note: Set-up only in the evening/night-time with little or no daylight.
Step 4: Exit programming mode
Briefly press the programming key [5] (<0.5s).
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Basic Settings Single Office:
•Light level of the two DALI channels: 100%
•Power up: By movement, push button or remote control
•Turn off: Automatic, push button or remote control
•Absence Switch-off delay time: 15min.
•Stand-by level: 30% of the stored set value
•Absence Stand-by delay time: 60min.
•Daylight harvesting: ON (Not active until set value is stored!)
•Offset: +30% for CH-2 (Does not show up until
daylight harvesting is dimming CH-1)
Optional settings (individually configurable)
Start with long press (>0.5s) of the programming key [5]. (Start programming mode)
LED [1] starts flashing red.
Absence Switch-off delay time
e.g. Briefly press the 30sec key [3] for a delay time of 30sec.
Note: 1sec test is purely a test function (Do not use)!
Absence Stand-by-level
e.g. Briefly press the 10% key [11] for a 10% brightness of the stored light
value.
Absence Stand-by delay time
e.g. Briefly press the 30sec key [12] for a 30sec delay time of
Stand-by before switch-off.
Note: Not possible if Stand-by level is set on OFF.
Daylight harvesting activation/deactivation
e.g. Briefly press the Off-button [14] to deactivate daylight harvesting.
Note: Default On (See DALIeco control manual for details).
Use full automatic mode only in combination with motion detection.
Motion Sensor activation/deactivation
e.g. Briefly press the Off-button [13] to deactivate motion detection.
Note: Default ON (See manual for details).
Exit with short press (<0.5s) of the programming key [5]. (End programming mode)
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Adjust Offset (not adjustable in the programming mode)
- Briefly press the Offset key [6] to start.
- Change Offset level with the CH-2 key [8].
- Briefly press the Offset key [6] to save and end.
Note: Only available in combination with the daylight harvesting.
Offset adjustment of CH-2 only between the CH-1 value and the
stored set value.
Adjust Offset with sufficient daylight only.
Note: Further information on the individual functions and
settings can be found in the DALIeco control user
guide.
Quick Start Guide
Open-Plan Office Mode
DALIeco

Attention!: All previous settings will be replaced by the
basic settings Corridor mode!
Step 1: Activate programming mode
Keep the programming key [5] pressed (>0.5s).
LED [1] starts flashing red.
Step 2: Select mode
Briefly press the Corridor mode button [4] (<0.5s).
DALI luminaires flash 1 time.
Step 3: Exit programming mode
Briefly press the programming key [5] (<0.5s).
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Basic Settings Single Office:
•Light level of the two DALI channels: 100%
•Power up: By movement, push button or remote control
•Turn off: Automatic before Stand-by, push button or remote control
•Absence Switch-off delay time: 5min
•Stand-by level: 10%
•Absence Stand-by delay time: permanent on
•Daylight harvesting: Deactivated
•Offset: Mode deactivated
Optional settings (individually configurable)
Start with long press (>0.5s) of the programming key [5]. (Start programming mode)
LED [1] starts flashing red.
Adapt brightness value
Set brightness value by pressing the buttons CH-1 [9] up/down.
Confirm by pressing the Manual setup key [10] briefly.
DALI luminaires flash 2 times; LED [2] will flash red/green during that period.
Note: The value last saved will be called up when switched on again.
Absence Switch-off delay time
e.g. Briefly press the 30sec key [3] for a delay time of 30sec.
Note: 1sec test is purely a test function (Do not use)!
Absence Stand-by-level
e.g. Briefly press the 10% key [11]
for a 10% brightness of the stored light
value.
Absence Stand-by delay time
e.g. Briefly press the 30sec key [12] for a 30sec delay time of
Stand-by before switch-off.
Note: Not possible if Stand-by level is set on OFF.
Motion Sensor activation/deactivation
e.g. Briefly press the Off-button [13] to deactivate motion detection.
Note: Default ON (See manual for details).
Exit with short press (<0.5s) of the programming key [5]. (End programming mode)
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Note:
D
aylight
harvesting
can be activated additional.
F
or details see
DALIeco control user guide.
Offset
can only be
activat
ed
in combination with
d
aylight
harvesting
.
Note: Further information on the individual functions and
settings can be found in the DALIeco control user
guide.
DALIeco
Quick Start Guide
Corridor Mode

Quick Start Guide
Meeting-/Classroom Mode
Attention!: All previous settings will be replaced by the
basic settings Meeting-/Classroom mode!
Step 1: Activate programming mode
Keep the programming key [5] pressed (>0.5s).
LED [1] starts flashing red.
Step 2: Select mode
Briefly press the Meeting-/Classroom button [4] (<0.5s).
DALI luminaires flash 1 time.
Step 3: Daylight harvesting - save set value for daylight harvesting automatically –OR–
Activate daylight harvesting by pressing Auto setup [7].
Luminaires dim to 80% and sensor value stored as target light intensity.
Note: Set-up only in the evening/night-time with little or no daylight.
Set-up duration is about 3 min. LED [2] will flash red/green during that period.
Daylight harvesting - save set value for daylight harvesting manually
Set brightness value by pressing the buttons CH-1 [9] up/down.
Confirm by pressing the Manual setup key [10]shortly.
Daylight harvesting will be activated.
DALI luminaires flash 2 times; LED [2] will flash red/green during that period.
Note: Set-up only in the evening/night-time with little or no daylight.
Step 4: Exit programming mode
Briefly press the programming key [5] (<0.5s).
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Basic Settings Single Office:
•Light level of the two DALI channels: 80%
•Power up: By movement, push button or remote control
•Turn off: Automatic, push button or remote control
•Absence Switch-off delay time: 15min.
•Stand-by: Off
•Daylight harvesting: ON (Not active until set value is stored!)
•Offset: +30% for CH-2 (Does not show up until daylight harvesting is dimming CH-1)
Optional settings (individually configurable)
Start with long press (>0.5s) of the programming key [5]. (Start programming mode)
LED [1] starts flashing red.
Absence Switch-off delay time
e.g. Briefly press the 30sec key [3] for a delay time of 30sec.
Note: 1sec test is purely a test function (Do not use)!
Absence Stand-by-level
e.g. Briefly press the 10% key [11
] for a 10% brightness of the stored light
value.
Absence Stand-by delay time
e.g. Briefly press the 30sec key [12] for a 30sec delay time of
Stand-by before switch-off.
Note: Not possible if Stand-by level is set on OFF.
Daylight harvesting activation/deactivation
e.g. Briefly press the Off-button [14] to deactivate daylight harvesting.
Note: Default On (See DALIeco control manual for details).
Use full automatic mode only in combination with motion detection.
Motion Sensor activation/deactivation
e.g. Briefly press the Off-button [13] to deactivate motion detection.
Note: Default ON (See manual for details).
Exit with short press (<0.5s) of the programming key [5]. (End programming mode)
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Adjust Offset (not adjustable in the programming mode)
- Briefly press the Offset key [6] to start.
- Change Offset level with the CH-2 key [8].
- Briefly press the Offset key [6] to save and end.
Note: Only available in combination with the daylight harvesting only.
Offset adjustment of CH-2 only between the CH-1 value and the
stored set value.
Adjust Offset with sufficient daylight only.
Note: Further information on the individual functions and
settings can be found in the DALIeco control user
guide.
DALIeco

Attention!: All previous settings will be replaced by the
basic settings Sanitary Room mode!
Step 1: Activate programming mode
Keep the programming key [5] pressed (>0.5s).
LED [1] starts flashing red.
Step 2: Select mode
Briefly press the Sanitary Room mode button [4] (<0.5s).
DALI luminaires flash 1 time.
Step 3: Exit programming mode
Briefly press the programming key [5] (<0.5s).
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Basic Settings Single Office:
•Light level of the two DALI channels: 100%
•Power up: By movement, push button or remote control
•Turn off: Automatic, push button or remote control
•Absence Switch-off delay time: 15min.
•Absence Stand-by delay time: 5min.
•Stand-by level: 30%
•Daylight harvesting: Deactivated
•Offset: Mode deactivated
Optional settings (individually configurable)
Start with long press (>0.5s) of the programming key [5]. (Start programming mode)
LED [1] starts flashing red.
Adapt brightness value
Set brightness value by pressing the buttons CH-1 [9] up/down.
Confirm by pressing the Manual setup key [10] briefly.
DALI luminaires flash 2 times; LED [2] will flash red/green during that period.
Note: The value last saved will be called up when switched on again.
Absence Switch-off delay time
e.g. Briefly press the 30sec key [3] for a delay time of 30 sec.
Note: 1sec test is purely a test function (Do not use)!
Absence Stand-by-level
e.g. Briefly press the 10% key [11
] for a 10% brightness of the stored light
value.
Absence Stand-by delay time
e.g. Briefly press the 30sec key [12] for a 30sec delay time of
Stand-by before switch-off.
Note: Not possible if Stand-by level is set on OFF.
Motion Sensor activation/deactivation
e.g. Briefly press the Off-button [13] to deactivate motion detection.
Note: Default ON (See manual for details).
Exit with short press (<0.5s) of the programming key [5]. (End programming mode)
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Note:
D
aylight
harvesting
can be activated additional.
F
or details see
DALIeco control user guide.
Offset can only be activated in combination with daylight harvesting.
Note: Further information on the individual functions and
settings can be found in the DALIeco control user
guide.
DALIeco
Quick Start Guide
Sanitary Room Mode

Attention!: All previous settings will be replaced by the
basic settings Staircase mode!
Step 1: Activate programming mode
Keep the programming key [5] pressed (>0.5s).
LED [1] starts flashing red.
Step 2: Select mode
Briefly press the Staircase mode button [4] (<0.5s).
DALI luminaires flash 1 time.
Step 3: Exit programming mode
Briefly press the programming key [5] (<0.5s).
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Basic Settings Single Office:
•Light level of the two DALI channels: 100%
•Power up: By movement, push button or remote control
•Turn off: Automatic, push button or remote control
•Absence Switch-off delay time: 5min.
•Absence Stand-by delay time: 1min.
•Standby level: 50%
•Daylight harvesting: Deactivated
•Offset: Mode deactivated
Optional settings (individually configurable)
Start with long press (>0.5s) of the programming key [5]. (Start programming mode)
LED [1] starts flashing red.
Adapt brightness value
Set brightness value by pressing the buttons CH-1 [9] up/down.
Confirm by pressing the Manual setup key [10] briefly.
DALI luminaires flash 2 times; LED [2] will flash red/green during that period.
Note: The value last saved will be called up when switched on again.
Absence turn-off delay time
e.g. Briefly press the 30sec key [3] for a delay time of 30 sec.
Note: 1sec test is purely a test function (Do not use)!
Absence Stand-by-level
e.g. Briefly press the 10% key [11
] for a 10% brightness of the stored light
value.
Absence Stand-by delay time
e.g. Briefly press the 30sec key [12] for a 30sec delay time of
Stand-by before switch-off.
Note: Not possible if Stand-by level is set on OFF.
Motion Sensor activation/deactivation
e.g. Briefly press the Off-button [13] to deactivate motion detection.
Note: Default ON (See manual for details).
Exit with short press (<0.5s) of the programming key [5]. (End programming mode)
LED [1] turns off.
Note: Programming mode will exit 60s after the last key press by default.
Note:
D
aylight
harvesting
can be activated additional.
F
or details see
DALIeco control user guide.
Offset can only be activated in combination with daylight harvesting.
Note: Further information on the individual functions and
settings can be found in the DALIeco control user
guide.
DALIeco
Quick Start Guide
Staircase Mode