OTE Speedport Entry 2i Programming manual

Speedport Entry 2i
Home Gateway
Maintenance Management Guide
Version: R2.0
OTE GROUP OF COMPANIES
99, Kifissias Ave. (HQ)
Maroussi - 15124
Athens - Greece
URL: http://www.cosmote.gr

SJ-20162405182123-002|2016-05-24 (R2.0)
2
LEGAL INFORMATION
Copyright © 2015 OTE GROUP OF COMPANIES
The contents of this document are protected by copyright laws and international treaties. Any reproduction or
distribution of this document or any portion of this document, in any form by any means, without the prior written
consent of OTE GROUP OF COMPANIES is prohibited. Additionally, the contents of this document are
protected by
contractual confidentialityobligations.
All company, brand and product names are trade or service marks, or registered trade or service marks, of OTE
GROUP OF COMPANIES or of their respectiveowners.
This document is provided “as is”, and all express, implied, or statutory warranties, representations or conditions
are disclaimed, including without limitation any implied warranty of merchantability, fitness for a particular purpose,
title or non-infringement. OTE GROUP OF COMPANIES and its licensors shall not be liable for damages resulting
from the
use of or reliance on the information containedherein.
OTE GROUP OF COMPANIES or its licensors may have current or pending intellectual property rights or
applications covering the subject matter of this document. Except as expressly provided in any written license
between OTE GROUP OF COMPANIES and its licensee, the user of this document shall not acquire any license
to the subject matter
herein.
OTE GROUP OF COMPANIES reserves the right to upgrade or make technical changes to this product without
further notice.
Users may visit the technical support website
http://www.cosmote.gr/fixed/help-and-support/internet/-/support/category/866732
to inquire for related information.
The ultimate right to interpret this product resides in OTE GROUP OF COMPANIES.
Revision History
Revision No. Revision Date Revision Reason
R1.0 2015-07-24 First edition
R2.0 2016-05-24 Second edition
Serial Number: SJ-20162405152123-002
Publishing Date: 2016-05-24(R2.0)

SJ-20162405182123-002|2016-05-24 (R2.0)
3
Contents
Chapter 1. Product Overview ...............................................................................1-1
1.1. Indicators................................................................................................................................... 1-1
1.2. Interfaces and Buttons .............................................................................................................. 1-2
1.3. Hardware Connection................................................................................................................ 1-3
1.3.1. PSTN line or Broadband Telephone Line with one voice channel ................................. 1-3
1.3.2. ISDN line......................................................................................................................... 1-5
1.3.3. Broadband telephone line – with the intervention of an electrician to the internal
(home) wiring (e.g. for an existing ISDN cabling installation)........................................ 1-6
Chapter 2. Configuration Preparation ..................................................................2-1
2.1. Configure TCP/IP (Manual Operation)....................................................................................... 2-1
2.2. Login .......................................................................................................................................... 2-2
Chapter 3. Configure the Internet .......................................................................3-1
3.1. Check the DSL Status ................................................................................................................. 3-1
3.2. Configure the WAN ................................................................................................................... 3-2
3.2.1. Configure the WAN Connection..................................................................................... 3-2
3.2.2. Configure the DSL .......................................................................................................... 3-5
3.3. Configure the Ethernet WAN Switch ....................................................................................... 3-10
3.4. Configure the QoS................................................................................................................... 3-10
3.4.1. Configure the QoS Global Parameters ........................................................................ 3-10
3.4.2. Configure the QoS Classification ................................................................................. 3-11
3.4.3. Configure the QoS Congestion Management.............................................................. 3-13
3.4.4. Configure the QoS Traffic Policing............................................................................... 3-15
3.4.5. Configure the QoS Traffic Shaping .............................................................................. 3-16
3.5. Configure the Security ............................................................................................................ 3-17
3.5.1. Configure the Firewall Level ........................................................................................ 3-17
3.5.2. Configure the Filter Criteria......................................................................................... 3-18
3.5.3. Configure the Local Service Control ............................................................................ 3-22
3.5.4. Configure the ALG ....................................................................................................... 3-24
3.5.5. Configure the DMZ ...................................................................................................... 3-25
3.5.6. Configure the Port Forwarding.................................................................................... 3-26
3.5.7. Configure the Port Trigger........................................................................................... 3-28
3.6. Configure the Parental Controls.............................................................................................. 3-29
3.7. Configure the DDNS ................................................................................................................ 3-30
3.8. Configure the SNTP ................................................................................................................. 3-31
3.9. Configure the Port Binding ..................................................................................................... 3-32
3.10. Configure the Dynamic Routing ............................................................................................ 3-33

SJ-20162405182123-002|2016-05-24 (R2.0)
4
3.11. Configure the Multicast ........................................................................................................ 3-34
3.11.1. Configure the IGMP................................................................................................... 3-34
3.11.2. Configure the MLD .................................................................................................... 3-35
Chapter 4. Configure the Local Network..............................................................4-1
4.1. Check the Local Network Status ............................................................................................... 4-1
4.2. Configure the WLAN ................................................................................................................. 4-2
4.2.1. Configure the Basic Parameters of the WLAN............................................................... 4-2
4.2.2. Configure the Advanced Parameters of the WLAN ....................................................... 4-5
4.3. Configure the LAN ..................................................................................................................... 4-7
4.3.1. Configure the LAN (IPv4) ............................................................................................... 4-7
4.3.2. Configure the LAN (IPv6) ............................................................................................. 4-10
4.4. Configure Route Menu ............................................................................................................ 4-14
4.4.1. Configure Routing (IPv4).............................................................................................. 4-14
4.4.2. Configure Routing (IPv6).............................................................................................. 4-17
4.5. Configure the UPnP................................................................................................................. 4-20
Chapter 5. Configure the VoIP .............................................................................5-1
5.1. Configure the SIP Accounts....................................................................................................... 5-1
5.2. Configure the Binding of VoIP port............................................................................................ 5-3
Chapter 6. Configure the Management and Diagnosis .......................................6-1
6.1. Check the Device Status............................................................................................................ 6-1
6.2. Configure the Account Management........................................................................................ 6-2
6.3. Configure the Login Timeout .................................................................................................... 6-2
6.4. Configure the System Management ......................................................................................... 6-3
6.4.1. Configure the Device Management............................................................................... 6-3
6.4.2. Upgrade Software.......................................................................................................... 6-4
6.4.3. Manage the User Configuration .................................................................................... 6-5
6.5. Check the TR-069 ...................................................................................................................... 6-5
6.6. Manage the Log ........................................................................................................................ 6-7
6.7. Diagnosis ................................................................................................................................... 6-8
6.8. Trace Route Diagnosis ............................................................................................................... 6-9
6.9. Check the ARP Table................................................................................................................ 6-12
6.10. Check the MAC Table ............................................................................................................ 6-13
6.11. Configure the Telephone Compatibility................................................................................. 6-13
Abbreviations......................................................................................................... I
Figures ...................................................................................................................4
Tables.....................................................................................................................8

SJ-20162405182123-002|2016-05-24 (R2.0)
5
Safety Precautions
Before using the device, read the following safety precautions. OTE GROUP OF
COMPANIES bears no liability to
the consequences incurred by violation of the safety
instructions.
Usage Cautions
l Readallthesafetycautionscarefullybeforeusingthedevice.
l Onlyusetheaccessoriesincludedinthepackage,suchasthepowersupplyadapter .
l Donotextendthepowercord,otherwisethedevicewillnotwork.
l The power supply voltage must meet the requirements of the device input voltage
(Thevoltagefluctuationrangeislessthan10%).
l Keepthepower plugcleananddry to prevent anyrisk ofelectric shock orother
dangers.
l Disconnectallthecablesduringalightningstormtopreventthedevicefromdamage.
l Poweroffandunplugthepowerplugwhenthedeviceisnotinuseforalongtime.
l Donotattempttoopenthecoversofthedevice.Itisdangeroustodosowhenthe
deviceispoweredON.
l Power off and stop using the device under the conditions such as, abnormal
sound,
smoke, and strange smell. Contactthe serviceproviderfor maintenanceif
thedevice
isfaulty.
Environment Requirements
l Ensureproperventilationtothedevice.Placethedeviceawayfromdirectsunlight.
l Keepthedeviceventilatedanddry. Neverspillanyliquidonthedevice.
l Donot place anyobjectonthedevicetopreventanydeformationordamage tothe
device.
l Donotplacethedevicenearanysourceof heatorwater.
l Keep the device awayfrom any householdappliances with strong magneticorelectric
fields,suchasmicrowaveovenandrefrigerator.
Cleaning Requirements
l Beforecleaning,poweroffthedevice,andunplugallthecablesconnectedtothe
device,suchasthe power cable and the Ethernet cable.
l Donotuseanyliquidorspraytocleanthedevice.Useasoftdrycloth.
Warning!

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
6
Environment Protection
l Donotdisposethedeviceimproperly.
l Observethelocal regulationsabouttheequipmentdisposalortreatment.
Environmental Information
The equipment you purchased has required the extraction and use of natural resources
for its production. It may contain substances that are hazardous to people’s health andto
the environment. To avoid putting such substances into our environment and to reduce
pressure on our natural resources, we ask that you reuse or recycle your end-of-life
equipment by using an accredited electronics take-back system.
The symbols below indicate that this product should be reused or recycled and not simply
discarded. Please locate and use an appropriate reuse and recycling site.
If you needmoreinformationon collection, reuseandrecycling systems,contactyourlocal
or regional waste administration or visit the technical support website in the following link
http://www.cosmote.gr/fixed/help-and-support/internet/-/support/category/866732.
You may also contact your equipment provider for more
information on the
environmental performances of these products.

SJ-20162405182123-002|2016-05-24 (R2.0)
1-1
Chapter 1. Product Overview
Table of Contents
Indicators.................................................................................................................................. 1-1
Interfaces and Buttons........................................................................................................... 1-2
Hardware Connection............................................................................................................. 1-3
1.1. Indicators
Figure 1-1 shows the indicators on the front panel of the Speedport Entry2i.
Figure 1-1 Indicators of the Speedport Entry 2i
Table 1-1 describes the indicators on the front panel of the Speedport Entry 2i.
Table 1-1 Indicators on the Front Panel
Indicator Color Status Description
Power
— Off Speedport Entry 2i is powered off.
White On Speedport Entry 2i is powered on.
WLAN
— Off Speedport Entry 2i is not powered on or the wireless interface is
Disabled.
White
On
The wireless interface is enabled.
Telephony
—
Off
No SIP account is registered.
White
On
At least one SIP account is registered.
DSL
—
Off
The device is powered off or the line has no signal.
White Flashing
2Hz
The DSL connection tries synchronization and training.
On The DSL connection is in synchronization state.
Online
— Off No internet services.
White On The internet services are running.

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
1-2
Indicator Color Status Description
Service
—
Off
No upgrade.
Orange
On
The software upgrade is in progress.
WPS
—
Off
The WPS button is not pressed, or the connection times out.
White
Flashing
2Hz
The WPS button is pressed.
If no wireless client is connected successfully, the light flashes for
about 2 minutes.
On If the wireless client is connected successfully , the light goes on
for about 5 minutes.
1.2. Interfaces and Buttons
Figure 1-2 shows the interfaces and buttons on the front panel of the Speedport Entry 2i.
Figure 1-2 Buttons on the Front Panel
Table 1-2 describes the interfaces and buttons on the front panel of the Speedport Entry
2i.
Table 1-2 Descriptions of the Buttons on the Front Panel
Button Description
WLAN Press the button for more than 0.5 seconds in power-On state. Then,
the wireless client can connect to Speedport Entry 2i.
WPS Press the button for more than 0.5 seconds in power-On state to
enable the function.
Figure 1-3 shows the interfaces and buttons on the back panel of the Speedport Entry 2i.

SJ-20162405182123-002|2016-05-24 (R2.0)
Product Overview
1-3
Figure 1-3 Interfaces and Buttons on the Back Panel
Table 1-3 describes the interfaces and buttons on the back panel of the Speedport Entry
2i.
Table 1-3 Descriptions of the Interfaces and Buttons on the Back Panel
Interface/Button
Description
DSL
RJ-11 DSL port.
Phone1–Phone2
RJ-11 port, connected to the phone through a telephonecable.
LAN1– LAN4 RJ-45 port, 10/100 Mbps auto MDI/MDIX, used to connect to a PC or
other network device.
Reset Reset button, used to restore the factory default settings when
pressed for more than 2 seconds in power-ON state.
Power
Power jacket, DC 12 V.
1.3. Hardware Connection
In the following paragraphs, 3 different topologies are described for the connection of Speedport
Entry 2i with a telephone line.
Before you start any connections, pick the telephone plug where you would like to install your
equipment.
1.3.1. PSTN line or Broadband Telephone Line with one voice
channel
If you have a PSTN line (analog telephone line) or a broadband telephone line, connect Speedport
Entry 2i as it is shown in Figure 1-4 below.
Among the components that are contained in the packing box, you may find an additional RJ-11, 1 to
2 ‘Y’ adapter (see point 1 in Figure 1-4). The names of the other components are referred in page 4 of
the manual “Equipment Installation Guidelines” which can be accessed in the following Internet
address:
https://www.cosmote.gr/fixed/documents/10280/87751345/quick_speedport_entry2i_16_02_15.pdf

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
1-4
Figure 1-4 Connection of the Speedport Entry 2i to a PSTN or a broadband telephone line.
1. Connect the telephone adapter (RJ-11, 1 to 2 ‘Y’ adapter) to the telephone outlet.
2. A. Connect one side of the blue telephone cable to one of the ports of the RJ-11 ‘Y’ adapter and the
other side to the blue port of the splitter with the indication “LINE”.
B. Following, connect the cable of the telephone set with the other port of the RJ-11 ‘Y’ adapter by
placing a filter in between.
3. Α.Connect one side of the gray telephone cable to the gray port of the splitter with the indication
“MODEM” and the other side to the gray port of the Speedport Entry 2i with the indication “DSL”.
B. Following, connect one side of the black telephone cable to the black port of the splitter with the
indication “Phone” and the other side of the cable to the black port of the Speedport Entry 2i
with the indication “Phone 2”.
4. Use the yellow ETHERNET cable to connect the ETHERNET port of your computer to one of the first
yellow ports of the Speedport Entry 2i with the indications LAN1, LAN2 or LAN3.
The port with the purple indication (STB) is used exclusively for the connection of the codec which is
required for the OTE TV service.
5. Connect the power supply adapter to the POWER jacket of Speedport Entry 2i and following,
connect it to the power plug. The LEDs for Power, DSL, Online, Telephony, Service and WLAN will
flash instantly.
After the conversion of your analog telephone line to a broadband telephone line, you may connect
an additional telephone set (e.g. telephone, fax) to the black port of Speedport Entry 2i with the
indication “Phone 1”, without using a filter.
6. To connect additional telephone sets to other telephone plugs, you must insert a filter. Connect the
telephone set to the filter and the filter to the telephone plug. Only one filter is contained in the
packing box. In case you need more filters, you will have to purchase them from a
telecommunications equipment shop.
Note: If your telephone network is connected to a device such as an alarm, private telephone switch
(PBX) etc., you will have to use an extra filter or splitter. You are kindly requested to ask for help from
a specialized installation team.

SJ-20162405182123-002|2016-05-24 (R2.0)
Product Overview
1-5
1.3.2. ISDN line
If you have an ISDN line, connect your Speedport Entry 2i, as it is shown in the following Figure 1-5.
Figure 1-5 Connection of Speedport Entry 2i to an ISDN line
1. Disconnect the cable that connects the ISDN (NT1) device to the telephone plug and connect it to the
black port of the splitter.
2. Α. Use the blue cable to connect the blue port of the splitter with the indication “LINE” to the
telephone plug.
Β.Following, using the gray cable, connect the gray port of the splitter with the indication “MODEM”
to the gray port of Speedport Entry 2i with the indication “DSL”.
3. Use the yellow ETHERNET cable to connect the ETHERNET port of your computer to one of the first
yellow ports of the Speedport Entry 2i with the indications LAN1, LAN2 or LAN3.
The port with the purple indication (STB) is used exclusively for the connection of the codec which is
required for the OTE TV service.
4. Connect the power supply adapter to the POWER jacket of Speedport Entry 2i and following,
connect it to the power plug. The LEDs for Power, DSL, Online, Telephony, Service and WLAN will
flash instantly.

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
1-6
1.3.3. Broadband telephone line – with the intervention of an
electrician to the internal (home) wiring (e.g. for an
existing ISDN cabling installation)
If you have a broadband telephone line and you already have a cabling installation from the main
telephone plug to the other plugs of your premises for telephony services only (e.g. from a previous
installation of an NT1 to an ISDN line), connect Speedport Entry 2i as it is shown in Figure 1-6 below
(the splitter and the NT1 are not required anymore).
Figure 1-6 Connection of the Speedport Entry 2i to the internal wiring with the intervention of an
electrician.
In case you have a telephone set connected to a telephone plug, you must disconnect it.
1. Use the gray cable to connect the gray port of Speedport Entry 2i with the indication “DSL” to the
telephone plug.
2. You may connect your telephone sets either to the port “Phone 1”, or “Phone 2” of your
Speedport Entry 2i.
3. Use the yellow ETHERNET cable to connect the ETHERNET port of your computer to one of the first
yellow ports of the Speedport Entry 2i with the indications LAN1, LAN2 or LAN3.
The port with the purple indication (STB) is used exclusively for the connection of the codec which is
required for the OTE TV service.
4. Connect the power supply adapter to the POWER jacket of Speedport Entry 2i and following,
connect it to the power plug. The LEDs for Power, DSL, Online, Telephony, Service and WLAN will
flash instantly.
You may connect other telephone sets to other plugs, directly (without a filter).

SJ-20162405182123-002|2016-05-24 (R2.0)
2-1
Chapter 2. Configuration
Preparation
This manual uses the Windows operating system as an example for describing how to
configure the Speedport Entry 2i. Before configuring the Speedport Entry 2i, you need to
perform the following operations:
l Ensurethatacrossoverorstraight-throughEthernetcableconnectsacomputerto
the device.
l EnsurethattheTCP/IPconfigurationonthecomputeriscorrect.
l Stopanyfirewallorothersecuritysoftwareoperatingonthecomputer.
l DisabletheproxysettingofInternetExplorer.
Table of Contents
Configure TCP/IP (Manual Operation)................................................................................. 2-1
Login......................................................................................................................................... 2-2
2.1. Configure TCP/IP (Manual Operation)
To log in to the Speedport Entry 2i on a computer, you need to set the IP address of the
computer to ensure that the IP address of the computer and the maintenance IP address
of the Speedport Entry 2i are in the same network segment. By default, the LAN/Wi-Fi
device gets the network information automatically (DHCP).
Context
The default maintenance IP address of the Speedport Entry 2i is asfollows:
l IP address: 192.168.1.1
l Subnetmask:255.255.255.0
l Defaultgateway:192.168.1.1
Steps
1. Use an Ethernet cable to connect a local computer to the LAN interface of the
Speedport Entry 2i.
2. On the local computer, double-click Local Area Connection and click Properties.
The Local Area Connection Properties dialog box is displayed.
3. Double-click Internet Protocol (TCP/IP).The Internet Protocol (TCP/IP) Properties
dialog box is displayed. Set the IP address to 192.168.1.200, subnet mask to
255.255.255.0, and default gateway to 192.168.1.1.
4. Click OK.
– End of Steps –

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
2-2
Follow-Up Action
After the IP address of the computer is set, you can run the Ping command to ping the
IP address 192.168.1.1. If the ping operation is successful, it indicates that the TCP/IP
configuration is correct and the computer is properly connected to the Speedport Entry 2i.
2.2. Login
The Speedport Entry 2i provides a web-based configuration and management system.
You can enter a specified IP address in the address bar of Internet Explorer to access the
system.
Prerequisite
A computer is directly connected to the Speedport Entry 2i, and their IP addresses are in
the same network segment.
Steps
1. Open the Internet explorer, and enter http://192.168.1.1 (default
maintenance IP
address of the SpeedportEntry 2i) in the addressfield. Press the
Enter key. The login
page is displayed, see Figure 2-1.
Figure 2-1 Login Page
2. Enter your username and password (the default username of the administrator
is admin) and click Login. The configuration page is displayed, as shown in Figure
2-2.

SJ-20162405182123-002|2016-05-24 (R2.0)
Configuration Preparation
2-3
The default password is located on the label underneath the device. It is suggested to
change the default password to one of your choice.
Figure 2-2 Configuration Page
– End of Steps –

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
2-4
This page intentionally left blank.

SJ-20162405182123-002|2016-05-24 (R2.0)
3-1
Chapter 3. Configure the
Internet
Table of Contents
Check the DSL Status............................................................................................................3-1
Configure the WAN.......................................................................................................................3-2
Configure the Ethernet WAN Switch ..................................................................................3-10
Configure the QoS.................................................................................................................3-10
Configure the Security..........................................................................................................3-17
Configure the Parental Controls..........................................................................................3-29
Configure the DDNS.............................................................................................................3-30
Configure the SNTP..............................................................................................................3-31
Configure the Port Binding...................................................................................................3-32
Configure the Dynamic Routing..........................................................................................3-33
Configure the Multicast.........................................................................................................3-34
3.1. Check the DSL Status
The section describes the status of DSL.
Steps
1. On the main page of the Speedport Entry 2i, select Internet > Status > DSL to go
to the DSL page.
The page is shown in Figure 3-1.
Figure 3-1 DSL Status

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
3-2
Before checking the information on WAN Ethernet (LAN1), make sure that Ethernet
WAN switch (Internet > Ethernet WAN) is set to On.
2. Click Refresh to refresh the information.
– End of Steps –
3.2. Configure the WAN
3.2.1. Configure the WAN Connection
This procedure describes how to configure a broadband connection (WAN connection) on
the network side, so that user services (including the data, voice, and video services) can
be connected to the external network.
The Speedport Entry 2i supports Route-based and Bridge-based WANconnections.
l Route-based connection
l Bridge-based connection
Prerequisite
Before configuring the WAN Ethernet (LAN1), make sure that the button On (Internet >
Ethernet WAN) is set and Apply button is pressed.
Steps
1. On the main page of the Speedport Entry 2i, select Internet > WAN to go to the WAN
Ethernet (LAN1) page.
2. Click to go to the page of creating a new Ethernet connection,
see
Figure 3-2.
Note:

SJ-20162405182123-002|2016-05-24 (R2.0)
Configure the Internet
3-3
Figure 3-2 New Item Page
3. Set the parameters. Table 3-1 lists the New Item parameters.
Table 3-1 Parameter Descriptions for the Route Mode
Parameter Description
ConnectionName To create a WAN connection, enter the name of the WAN connection.
Type The connection type includes Routing and Bridge Connection.
In this case, Routing is selected (for Internet service).
Service List
Options: INTERNET_TR069 and INTERNET_VoIP_TR069.
This parameter must be consistent with service configuration. For
example, if INTERNET_TR069 is selected, it indicates that the WAN
connection supports the Internet access service and remotemanagement.
If INTERNET_VoIP_TR069 is selected, it indicates that the WAN connection
supports the Internet access service, remote management and the voice
service.
MTU Maximum Transfer Unit of the WAN connection. If Link Type is set to IP,
MTU range is 576–1500, default: 1500. If Link Type is set to PPP, MTU
range is 128–1492, default: 1492.
Link Type There are two link types:
l PPP
l IP
PPP Transfer
Type The default value is PPPoE.

SJ-20162405182123-002|2016-05-24 (R2.0)
Speedport Entry 2i Maintenance Management Guide
3-4
Parameter Description
PPP
Username Username of the PPPoE account. The username must be the same as that
set on the peer server for authentication.
Password Password of the PPPoE account. The Password must be the same as that
set on the peer server for authentication.
IP Version
IP version that the device supports. Normally, it is set to IPv4.
l IPv4 :ThedevicesupportsIPv4addressesonly.
l IPv6 :ThedevicesupportsIPv6addressesonly.
l IPv4/IPv6 :ThedevicesupportsbothIPv4andIPv6addresses.
IPv4
IP Type Options:
l DHCP :TheDHCPserverautomaticallyallocatesadynamicIPaddress
to thedevice.
l Static : Youneedto specifyastatic IPaddressforthedevice.
IP Address Specifies the IPv4 address for the WAN connection when IP Type isStatic.
Subnet Mask Subnet mask of the WAN connection when IP Type is Static.
Gateway The net-hop IP address to the destination network.
DNS1/DNS2/
DNS3 IPv4 address of the DNS server for static connections. You can set up to
three IPv4 addresses for the server. These IPv4 addresses are provided
by the ISP.
IPv6
IPv6 Info Acquire
Mode Specifies how to acquire IPv6 information for the WAN connection. It isvalid only if the WAN connection supports IPv6.
The options are:
l Manual : Youneedto settheglobaladdress,gateway,and
DNS
acquisition modes.
l Auto :Theglobaladdress,gateway,andDNSacquisitionmodesare
automatically configured.
Manual DNS Set radio button to On to enable the function of acquiring the IPv6 DNS
address
manually.
DNS1/DNS2/
DNS3 IPv6 address of the DNS server for static connections. You can set up to
three IPv6 addresses for the server. These IPv6 addresses are provided
by the ISP.
Router
Solicitation Make sure the IP address is sole.
SLAAC If setting radio button to On, the device generates a global address in
accordance with the RA packets from the upper-layer server.