Outdoor Revolution Ozone 6.0XT User manual

Ozone 6.0XT
Instrucons and
Care Manual
Thank you for purchasing an Outdoor Revoluon product,
this product will give years of sasfactory service if basic
instrucons are followed, our products are designed for
durability and for ease of erecon.
**We highly recommend that you insure your tent
against storm damage or accidental damage, as the
warranty does not cover such eventualies. The
manufacturer is not liable for any damage caused to
the tent or its contents because of misuse, incorrect
pitching or extreme weather**
IMPORTANT: PLEASE CHECK YOUR EQUIPMENT
1 x Flysheet (or outer)
1 x Bag of steel pegs
2 x Reecve Endurance Storm Straps
1 x Dual Acon Hand Pump
Carrying Bag
1

Important informaon.
 Please do not leave for your holiday without fully erecng and
checking you have all the contents of your tent. If you are missing any-
thing please contact your supplying dealer.
 Please also note that manmade fabrics are prone to condensaon
when the warm air and moisture inside the awning comes into contact
with the colder outside of the tent fabric. This is a perfectly natural
occurrence and should not be confused with leaking. Ensure all Vortex
Vents are open whenever possible to help combat condensaon.
 Ideally erect your tent for some period before use - allowing it to
weather. ‘Weathering’ can take few uses of the tent before it is fully
eecve.
 Make sure that before erecng, that you site the tent on clear level
ground with no sharp objects underneath, and that all the zips are fully
closed. (We recommend laying a groundsheet down to keep the
awning dry and clean).
 We suggest conducng a trial run of your tent to familiarise yourself
with the set up and use of it. If you have any issues relang to pitching
your tent please contact your dealer for help before going on holiday.
 Aer use always dry and air the tent before packing away to prevent
damp.
 Any dirt or stains can be removed by brushing or gently washing with
warm water. DO NOT use detergents as this will destroy the
waterproong on the fabrics.
 DO NOT cook or smoke in this tent; although the outer fabric is re
retardant treated it will sll melt.
 In the event of damage; use our contact form on our website
www.outdoor-revoluon.com and our customer service team will
advise you as best as possible.
2
Oponal Extras Available for the Ozone 6.0XT
 Camping Carpet - cosy, so carpet to t on top of the ground-
sheet in your drive-away awning.
 Ozone Canopy - large canopy that zips on to the front of this
tent providing addional living space.
 Trio Stripe Sleeping Bags - Available in dierent sizes,
matching sleeping bags.
 Selecon of chairs and furniture.
 Look at www.outdoor-revoluon.com for more informaon.
Lifeme Guarantee
 The Ozone AirFrame Tubes come with a lifeme guarantee*.
 You must sign up for the Lifeme Guarantee on the Outdoor
Revoluon website for it to be valid.
*Terms and Condions apply - nd the full terms
and condions on our website*
3

PLEASE READ THE FOLLOWING ERECTION
INSTRUCTIONS CAREFULLY.
TIP: Refer to the photograph to help when pitching your Ozone 6.0XT
1. Spread the ysheet out on the
ground of your pitch in the place
you want to pitch it.
2. Peg down the four corners of the
tent to hold it down whilst you inate
the AirFrame Tubes.
3. Before inang any of the AirFrame
Tubes make sure the Dynamic Speed
Valve quick release buons are pressed
out. This makes sure the air will be held
inside the Airframe.
4. Next, aach the pump to the rst of
the ve Dynamic Speed Valves and
begin to carefully inate—taking care
that no part of the fabric is caught any-
where.
4
6. Repeat steps four and ve with the
other four AirFrame Tubes. Then
place the caps back in the valves and
cover with the Velcro sleeve to keep
the outside of the tent looking neat
and dy.
7. Then peg out and tension the tent. Use
the adjustable pegging straps to tension
the tent as you desire. Make sure you
don’t over tension the fabric. If a door is
taut it may be too ght and that could
cause damage.
5. Inate the Airframe unl you can
give it a good squeeze. The tube wants
to have room inside for air to expand.
Don’t worry if you do keep inang—
the Intelligent Frame will release any
excess air. (Please note the Intelligent
Frame is set to 5.5psi).
5
8. Finally. peg out the Reecve Endur-
ance Storm Straps for extra stability.
Please make sure in heavier weather
you use all the guy lines and storm
straps to hold the awning in place.

Warning: Never unzip the zips on the protecve
sleeves whilst the AirFrame Tubes are inated. This
may result in the tube bursng or ballooning out of the
sleeve - causing damage to the tube and the sleeve.
Visit the website for Video Instrucons
6
 Fold the tent lengthways to
make a long thin straight line.
Packing away your awning.
 Zip up all the windows and doors before deang.
 Unpeg the guy lines, storm straps and most of the pegs around the tent
- leaving the four corners pegged out.
 Open each of the Dynamic Speed Valves in turn and press in the quick
release buon. Leave the buon pressed in.
 Lay the tent at on the ground.
 Measure the width of the bag
up against the width of the fold-
ed tent to make sure the tent is
going to t.
 Begin to roll the tent as ght as
possible from the opposite end
of the Valves to expel all the air
as you roll.
 Place the rolled awning on to
the bag and pull the sides up
round it. Finally, zip up the bag.
7
9. Lay out the inner tent inside the tent
and posion it in the correct place with
the bedroom doors facing into the tent.
Start and the back of the bedroom and
clip it to the black clips on the oor.
10. Work your way around the elascated
tabs connecng them to the canvas of the
tent. Make sure you line up the coloured
eyelets with the correct coloured elasc
to make sure you t the inner tent cor-
rectly.
11. Finally, repeat the last few steps for
the second row of elascated straps at
the front of the inner tent.

Problem Reason Soluon
The Air Tube keeps
deang aer removing
the pump.
The Dynamic Speed Valve
quick release buon hasn’t
been pressed back out.
Press the quick release
buon back out to shut
the valve.
The tent is leaking. Usually ‘leaking’ is actually
condensaon which forms
on the inside of the product.
Open all the Vortex
Vents in the tent to help
increase air circulaon
and help reduce conden-
saon.
Trouble-Shoong.
In the event of a puncture.
 If you have a small puncture in your Air Frame Tube you can easily re-
pair it using a standard puncture repair kit.
 To remove the Air Frame Tube - deate the tube and then unzip the
two protecve sleeves over the tube and pull the Air Tube out. Do not
unzip the sleeves whilst the tube is inated.
 Locate the puncture repair the puncture on the Air Frame Bladder.
 Place the Air Tube back in to the sleeves in the correct place with the
valves in the valve hole. Make sure the Tube is straight and not twisted.
 Zip the two sleeves back up fully before starng to re inate.
 Inate the AirFrame Tube again, ensuring that the puncture has now
been repaired.
 If this process doesn't work you may have to buy a new bladder.
**Spare AirFrame Bladders can be bought to replace damaged ones.
Visit the Spares Secon at www.outdoor-revoluon.com or contact us on
01924 455313**
**Tents will not be replaced because of damaged bladders**
8
Outdoor Revoluon Awnings are distributed by:
Outdoor Revoluon Ltd
www.outdoor-revoluon.com