OVALAIR AIR1000 User manual

Purifying Air Filter
Operating Instructions |Model # AIR1000
How The Purifying Air Filter Works:
The Air Purifier helps to clean and purify indoor air by using a combination of filters and
Anion technology. The cold catalyst and charcoal filters work to remove indoor air pollutants
like benzene, formaldehyde and other VOCs, while the HEPA filter removes 99.7% of pollen,
pet dander, dust mites, and smoke.
The Anion ionizing feature releases negatively charged ions to freshen the air and reduce
odors.
The Air Purifier is an appliance and must not be used by children under 8 years old. It is not a toy. Cleaning and
maintenance should be performed by an adult.
Table of Contents
1-2 How The Air Purifier Works
3 Where To Place The Air Purifier
4-5 Safety Instructions
6 How To Operate The Air Purifier
7 Cleaning And Maintenance
8-9 Filter Replacement
10 Trouble Shooting
10 Technical Specifications11 Technical Specifications
USERGUIDE |Page 1

Purifying Air Filter
Operating Instructions |Model # AIR1000
USERGUIDE |Page 2

Where To Place The Air Purifier
The Air Purifier is designed for use in
rooms with good air circulation.
Place the Air Purifier at least
4 inches (10cm) from nearby walls and furniture.
Make sure the Air Purifier is placed at least
6 feet (2 meters) from all appliances and
electronic devices.
Do not place the Air Purifier near curtains,
draperies, or upholstery.
6 FT
4IN 4IN
USERGUIDE |Page 3

Safety Instructions
The Air Purifier is equipped with a high speed rotating motor. Please follow the
Safety Instructions below to avoid personal injury or damage to the appliance.
The Air Purifier
is for Indoor Use Only.
Do not use the Air Purifier in
bathrooms or other high-humidity spaces.
Never insert anything into the Air Purifier,
including tools.
Do not use the Air Purifier
as a kitchen stove air filter for cooking;
it is not designed to filter out oil and soot.
USERGUIDE |Page 4

Safety Instructions
The Air Purifier is equipped with a high speed rotating motor. Please follow the
Safety Instructions below to avoid personal injury or damage to the appliance.
Place the Air Purifier on flat surfaces only, to
avoid any possibility of it tipping over.
Never touch the Air Purifier if
your hands are wet.
Do not use the Air Purifier in any environment
that may contain flammable liquids,
such as a garage or shed.
Avoid direct exposure to hot sunlight.
If the power cord is damaged or
becomes knotted, stop using the Air Purifier
immediately until the cord can be replaced.
USERGUIDE |Page 5

How To Operate The Air Purifier
Once the power cord is ageing, knotting, or damaged, please stop using the
machine immediately. Ovalair Air Purifiers should only be maintained or replaced
by the manufacturer or professional personnel
Sleep
Press for Sleep Mode;
the fan will be set at a
low speed and the
unit’s lights will dim.
Press the Sleep or
Speed button to exit
Sleep Mode.
Speed
The Speed button
starts the fan at the
lowest speed; press
the button again to
increase speed.
Power
Connect the Power
Supply Cable, and
plug the unit into a
wall outlet.
RESET
LOCK
Timer
Press the Timer
button to set an
automatic shutoff time.
Lock
The Lock button unlocks
the unit if an incorrect
combination of buttons
accidentally causes it to lock.
Filter Reset
The filter should be replaced every
3000 hours of operation. After
replacing the filter, press and hold
the Reset button for 5 seconds to
restart the replacement timer.
Anion
Press the Anion
button to turn the air
ionizing feature on
and off.
USERGUIDE |Page 6
AUTO
Auto
The Auto button
balances energy
efficiency and comfort
by automatically
adjusting to the most
appropriate mode.

Cleaning & Maintenance
The Air Purifier is easy to clean and maintain. Just wipe down surfaces with a clean,
dry cloth, or dust with a microfiber duster. Always unplug the unit before cleaning.
Never use water to clean, and do not wash the filters or filter components.
Replace the filters on the following schedule:
HEPA Filter: Replace every 1-2 years
Charcoal Filter: Replace every 3-5 years
Air Purifier units in environments with
high levels of pet dander and dust may
need the filters replaced more often.
For best performance, please
use only Air Purifier brand replacement filters.
USERGUIDE |Page 7

Filter Replacement
Remove the Front Panel
With the front of the unit facing
you, gently remove the front panel
by releasing the small latch at the
upper left corner.
Tilt the panel forward and lift to
disconnect it at the bottom.
Remove the Filter Frame.
USERGUIDE |Page 8

Filter Replacement
Replace the Front Panel
Replace the Front Panel by gently
clicking it into place.
Grab the filter frame along the edges
and pull to tilt it forward, then lift it out.
Remove the Filter Elements
from the Frame, and discard the
element you are replacing.
Reassemble the Filter Frame,
incorporating the new Filter Element.
NOTE:
Refer to the numbers on the filter elements to place
them into the frame in the correct order, #1 - #4
USERGUIDE |Page 9

Troubleshooting
USERGUIDE |Page 10
Problem Possible cause Solution
The Air Purifier
unit is not running
The Air Purifier
unit is not
removing smoke
and odors
1. The Power button has
not been turned to ON.
2. The unit is not plugged
in, or it is plugged
into an outlet
without power.
1. The Filter Elements
may be installed in the
wrong order. The Filter
Elements may need to
be replaced.
2. The air inlet on the
unit is blocked by
an object.
1. Plug in the unit.
2. Press the Power
button.
3. Confirm that the
outlet has power to it.
1. Remove the Filter
Frame and confirm
the Filter Elements
are installed in the
correct order.
2. Replace the Filter
Elements.
3. Remove any objects
close to the air inlet.

Specifications:
Model AIR1000
The rated voltage 120V
Rated frequency 60Hz
Rated power 60W
Rated noise ≤50db
Solid pollution clean air volume 3000ft3/h
Applying area up to 600sqft
Weight 13.23lbs
Product size (L*W*H) 13.78" x 7.48" x 25.2"
The Air Purifier unit needs repair or replacement if:
You follow the steps above and the Air Purifier unit is still not working
properly. A foreign object enters the unit and it stops working.
The power cord is damaged.
USERGUIDE |Page 11