OVER-EAR Harry User manual

234CHANGE CHANNELS
Tap the power button to
change channels, LED
changes colour. (When
multiple transmitters
in use).
1CHARGE UP
Ensure Harry is fully
charged (plug into
USB socket, charge
for up to 3 hours).
SWITCH ON
Press and hold the
power button (2 secs)
to switch on or off.
Harry setup...
WWW.OVER-EAR.COM
Falcon Donkey Parakeet
Bob Joe Ned
Make the most of
your Harry...
Harry is compatible with a wide range of OVER-EAR
products including transmitters and different
receivers. Mix the products you need to create your
perfect system.
Compatible with:
What’s in the box
Headphones & charge cable
Harry
Professional Wireless
Headphones
WWW.OVER-EAR.COM Charge cable
START AUDIO
Set up transmitter
with music playing
(see separate product
instructions).

MEET HARRY TECHNICAL
SPECIFICATION
SAFETY
INSTRUCTIONS
DO DON’T
TROUBLE
SHOOTING
NO AUDIO / MUSIC?
Check your music playing device is
working, connected correctly, playing
music with volume turned up full.
Try a different device and audio cable.
Ensure receivers/ headphones are
switched on, connected to correct
channel and have volume up.
The headphones turn themselves off
after not receiving audio for 10 minutes,
so if this happens check the transmitter
is still broadcasting.
SIGNAL CUTS OUT, INTERFERENCE
OR REDUCED RANGE?
Ensure there is no interference caused
by other wireless equipment in the vicinity.
If using 2 or more transmitters
simultaneously make sure each is on
different channels (frequencies). You
cannot use 2 transmitters on the same
channel in the same place ever. They will
cancel each other out, resulting in little
or no signal.
NO POWER?
Check the headphones are fully charged
and switched on.
NO LIGHT?
If the headphones power on but there
are no flashing lights - press the volume
control to turn them back on.
1. LED indicator
IN USE
Red LED illuminates when headphone is
on.
CHARGING
[Power off] - LED illuminates green
while charging, LED goes off when fully
charged.
[Power on] - LED illuminates green . LED
turns red when fully charged.
2. Power/ tune button
Press and hold for on/off (2 sec).
Quick tap to change channels.
3. Large LED light
Indicates chosen channel colour.
4. Volume
Use + or - to adjust audio input volume.
LIGHT SETTING
Push in and hold volume wheel to cycle
between 3 light settings (full light, half
light, no light).
Selection is stored in memory for next
time headphones are used.
5. 3.5mm jack socket
Input - can be used to connect to audio
device using standard 3.5mm cable.
Output - can be used to share received
audio with another audio device (ie
headphones), by connecting to socket.
6. Flashing LED light
Pulses in time to the music.
7. USB socket
Insert charge cable to recharge.
•Switch off and disconnect equipment from
mains before cleaning.
•Do not repair or replace parts for any products.
•Do not use equipment if damaged by water,
heat, physical impact etc.
•Do not use or store equipment in or near water,
moist or hot environments.
•Keep away from radiators and heat generating
electrical equipment such as screens and amps.
•Use only the supplied power cable and
accessories with your product.
•Disconnect from power after charging and
especially when not being used for long periods
of time. Overcharging headphones can cause
damage to the battery.
•Ensure that power connection is plugged in
properly - not damaged, working within a
comfortable temperature and not exposed to
direct sunlight.
•Do not overload wall sockets.
•Failure to comply with safety guidelines can
result in electrical shock, fire, damage to
equipment and invalidate your warranty.
•If in doubt please contact dealer or
manufacturer.
Do use headphones and
systems at comfortable
and safe listening levels.
Do gently clean
equipment between
uses and users. Hygienic
wipes and ear pad covers
are available from your
supplier.
Do feel free to expand
your system. Mix and
match with a variety of
OVER-EAR transmitters,
headphones and
receivers.
Do call, email or visit us
for help and advice.
Don’t use 2 or more
transmitters on the same
channel - they won’t
work.
Don’t use equipment
near other wireless
apparatus including radio
mics, transmitters etc.
Frequencies can interfere
and result in distorted or
no signal.
Don’t attempt to repair
or modify equipment
yourself. This
could seriously harm
somebody.
Don’t use headphones
for extended periods of
time.
Model number: OE600L
Dimensions: 15cm (19cm extended)
Weight: 210g
Sound: Stereo, HD or SD Mode
Frequency
Response: 30-15,000Hz
Channel
Separation: >40dB
System: UHF/ RF
Modulation: FM
S/N ratio: > 75db
Connections: 3.5mm audio
Power Source: 600mAh
3.7v Lithium Battery
Charge Voltage: 5v
Charge Current: 200mA
Charge Time: <3 hours
Battery Life: 10+ hours (lights on)
Noise Reduction: Yes
Speaker: Advanced 40mm
Impedance: 32 ohm
Power Saving: After 10 minutes of no
detected signal
Operational
Distance:
>300m (optimum)
Frequencies: Custom i.e. 433MHz/
863MHz/ 915MHz etc
LED Colour Typical Frequency
EU USA AUS
Red 863.1MHz 914MHz 433.1MHz
Green 863.7MHz 915MHz 433.7MHz
Blue 864.9MHz 916MHz 434.9MHz
Yellow N/A 917MHz N/A
Please note frequencies and other specifications
may be changed without notice.
If in doubt please confirm with supplier.
6.
7.
2.
1.
3.
4.
5.
NEED HELP?
Feel free to drop us a line at:
[e-mail]