Overland Tandberg NEOxl 40 User manual

10400903 ©2019 Overland-Tandberg Page 1 of 2
*10400903*
NEOxl 40 3U Tape Library
Spare Expansion Module Controller Instructions
This document describes how to remove and replace a
Expansion Module Controller in a NEOxl 40 3U tape library
from Overland-Tandberg.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working with
the library.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the library, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Prepare the Library
Identify the Failed Component Module
Using the RMI or OCP, activate the Unit Identification (UID)
LEDs to locate the appropriate Expansion Module containing
the failed component.
Power Off Library
If still running, power off the library from the Base Module
front panel by pressing and holding down the power button for
three (3) seconds.
NOTE: If the library does not perform a soft shutdown, press and
hold the power button for 10 seconds.
Verify that the Robotic Assembly is in its parked position and
that all host processes are idle.
Remove Cords and Cables
Disconnect all cables and cords, noting where they connect.
1. Unplug any AC power cords (1).
2. Remove the expansion interconnect cables (2) from
the Expansion Module and any other modules to which it
is connected.
NOTE: Completely remove the expansion interconnect cables
from the modules to prevent damaging the cables during
module removal and replacement.
1
2

http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
NEOxl 40 Spare Expansion Module Controller
10400903 ©2019 Overland-Tandberg Page 2 of 2
Replace the Controller
1. At the rear of the Expansion Module, loosen the two blue
thumbscrews on the old controller.
2. Using the thumbscrews, slowly remove the controller
from the module and set it aside.
3. Position the new controller on the alignment rails.
4. Slide the controller slowly into the module until it is flush
with the rear panel of the module.
5. Finger-tighten the thumbscrews to secure it.
Reattach Cables and Cords
1. Reconnect the expansion interconnect cables (2) from
the Expansion Module to any adjacent modules.
2. If power supplies exist (1), reconnect the AC power
cords.
Power on the Library
Power on the library from the Base Module front panel by
pressing and holding down the power button for three (3)
seconds until the green light on the front panel illuminates
indicating the status is
Ready .
Verifying the Installation and Configuration
Check the following:
•Verify that the library powers on and initializes correctly,
and that the status is Ready.
•From the OCP or RMI, verify that the Expansion Module
is visible showing all the tape drives and both magazines.
It is recommended that you always update the library to the
latest firmware version.
You can update firmware from either the RMI or by going to
the OCP
Maintenance > Library Firmware Upgrade screen.
Return Replaced Part to Overland
For warranty replacements:
1. Place the old part in the anti-static bag and put it in the
replacement part’s box.
2. Use the existing packing material to secure it in the box.
3. Use an RMA to return the part to Overland Storage.
For return shipping details and RMA number, go to:
http://docs.overlandstorage.com/return-instructions.
1
2