Overland Tandberg SnapServer XSR120 User manual

10400844-001 12/2017 ©2017 Overland Storage Page 1 of 4
*10400844-001*
SnapServer®XSR120
Add-on/Spare PCIe Card Instructions
This document describes how to add a new PCIe card to or
replace an existing PCIe card in an Overland-Tandberg
SnapServer XSR120.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working with
the unit.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
NOTE: A spare, replacement PCIe card may come without the
mounting bracket. Reuse the existing bracket.
Register a New PCIe Card
NOTE: If you are only replacing an existing PCIe card, skip ahead to
the next section, “Prepare the Unit.”
It is essential that the product be registered because technical
and warranty support is not available until then.
For an existing customer:
1. Go to http://support.overlandstorage.com/ support page.
2. Enter your e-mail address and password, and then
press Enter or click the right arrow (>).
3. At the Support Home page, click Register New.
4. Enter the requested information and click Submit.
Your warranty certificate will be emailed to you. Follow
the instructions in the email to complete the process.
For a new customer, go to the New User Registration page
and follow the instructions there.
Existing User Login
New User Registration
Prepare the Unit
Power Off and Disconnect
If the unit is still running, power it down cleanly:
1. Use the Web Management Interface to power off the unit
(
Maintenance > Shutdown/Restart > Shutdown ).
2. When all the LEDs are off, disconnect the power cords.
3. Disconnect the remaining data cables from the unit,
noting their locations.
EnterEnter
Enter
All Fields
Data Cables
Power

10400844-001 12/2017 ©2017 Overland Storage Page 2 of 4
SnapServer XSR120 Add-on/Spare PCIe Card Instructions
Remove the Front Bezel
1. Carefully take hold of the front bezel and pull it straight
out from the appliance until it releases.
2. Set the bezel aside on a secure surface.
Remove the Drives
IMPORTANT: Overland recommends that you remove all the
drive carriers to reduce the unit’s weight prior to rack removal.
Blank (empty) carriers can remain in the bays.
1. Press the release button on the right side of the carrier.
2. Using the built-in handle, pull the carrier out.
3. Set the drive carrier on a secure surface.
4. Repeat Steps 1–3 for all the remaining drive carriers.
NOTE: Do not remove the drives from their carriers as doing so
voids the drive warranty.
Remove the Chassis from the Rack
WARNING: It is recommended that a mechanical lifter (or at
least two people) be used during rack installation or removal to
prevent injury.
WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir zur
Rack-Installation oder -Deinstallation die Nutzung einer
mechanischen Hebehilfe (oder mindestens zwei Personen).
AVERTISSEMENT: Pour éviter toute blessure il est
recommande qu'un monte-charge (ou deux personnes au
moins) soit utilisé lors de l'installation ou de l'enlèvement du
support.
1. Release the two captive screws on the lower part of the
left and right front flanges.
2. Slide the chassis out until it stops.
3. With a lifter positioned in front of the chassis, release the
rail locks and slide the chassis onto the lifter.
4. Move the chassis onto a secure surface.
Install/Replace the PCIe Card
Remove the Rear Top Panel
1. Remove and retain the four screws on the sides holding
the rear top panel.
2. Using the panel depressions, slide the panel rearward
about one-half inch (1.25cm).
3. Lift the rear top panel off and set it aside.
1 2 3 4
5 6 7 8
9 10 11 12
Press
Chassis
Secure Surface
Screws
Screws

10400844-001 12/2017 ©2017 Overland Storage Page 3 of 4
SnapServer XSR120 Add-on/Spare PCIe Card Instructions
Install or Replace the PCIe Card
1. At the rear, remove and retain the screw securing the
rear access cover bracket.
2. Do one of the following:
•If installing a new card in an empty slot, remove the
rear panel access cover at that slot and set it aside.
Continue with Install the PCIe Card.
•If replacing an existing card, remove the card from
the motherboard slot and set it aside on an ESD
surface. Continue with Swap the Mounting Bracket.
Swap the Mounting Bracket
NOTE: If the spare came with a mounting bracket attached,
continue with Install the PCIe Card.
1. Remove and retain the two screws securing the
mounting bracket to the old card.
2. Remove the mounting bracket from the old card and
position it on the new card.
3. Using the two retained screws, secure the bracket to
the new card.
Install the PCIe Card
1. Seat the card firmly in the motherboard slot with the
card bracket positioned in the open rear bracket slot.
2. Using the retained screws, secure the locking bracket.
Reinstall the Rear Top Panel
1. Position the rear top panel on the chassis with no more
than one-half inch (1.25cm) extending out over the rear
of the unit.
2. Slide the panel forward until it is fully seated.
3. Using the four retained screws, secure the panel.
Reinstall the Chassis in the Rack
Remount the Chassis
1. Pull the middle rack rails out of the rack.
2. Using the mechanical lifter, position the chassis in front
of the rack rails.
3. Slide the chassis side rails into the rack rails, and push
the chassis all the way to the rear.
4. Secure the chassis using the two captive screws on the
front flanges.
Screw
Bracket
Remove Screws
Screw
Bracket
Screws
Screws

10400844-001 12/2017 ©2017 Overland Storage Page 4 of 4
http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
SnapServer XSR120 Add-on/Spare PCIe Card Instructions
Reinstall Drives
1. Position a drive assembly in front of an empty bay.
2. Slide the assembly in until the latch clicks, securing it.
3. Repeat Steps 1–2 for all remaining drive carriers.
IMPORTANT: To maintain proper airflow and cooling, a drive
carrier or blank carrier must be installed in every bay. No
empty bays are allowed.
Reattach the Bezel
1. Position the bezel with the bezel tabs aligned inside the
top and bottom edges of the chassis.
2. Push the bezel onto the unit until it snaps into place.
3. Verify that the bezel is aligned properly with all the
LEDs visible and the Power Panel on the right side in line
with the hole on the bezel flange.
Reattach the Cables and Power Cord
1. Reattach all the cables (not including the power cords) to
the same chassis connections previously used.
2. Next, attach the power cords.
3. At the front, press the power switch to power it on.
Return the Replaced Part to Overland
1. Put the replaced part in the anti-static bag and place it
in the box the part came in.
2. Use an RMA to return the part to Overland Storage.
For an RMA number and return shipping details, go to:
http://docs.overlandstorage.com/return-instructions
Magnets Bezel Tabs
Data Cables
Power