OVIS 32211 User manual

32211 King Bed
REV 01

CAUTION:
PLEASE CONTACT US FOR QUESTIONS
Email our support team: [email protected]o
Do not a empt to slide the bed once it is fully
assembled. To avoid structural damage while moving
your assembled bed, any ma ress and bedding should be
removed from the bedframe. Then the bedframe should
be lied and carried (not slid) to your desired locaon.
Max Weight Limit 600lbs.
When placing furniture on non-carpeted flooring, we
recommend the use of floor protecon such as an area
rug or furniture pads. Area rugs and padding not
included with purchase.
When using an adjustable base please use the legs
provided with the adjustable base for maximum support.
Using zero clearance adjustable bases without legs
directly on the slats is NOT recommended and will void
your warranty.

LB
Estimated Time for Assembly
Weight Limitation
25:00 - 35:00
Additional Tools Needed – Phillips Screwdrive.
600 lbs

Remove parts from headboard
compartment
PLEASE CONTACT US FOR QUESTIONS
Email our support team: [email protected]o

Hardware
Components
1 pc
1 pc
2 pcs
2 sets
2 pcs
8 pcs
4 pcs
18 pcs
M6
O
10 pcs
M6
P
1 pc
M4
Q
1 pc
M5
R
King Bed
2 rolls
PACKAGE CONTENT
CAUTION:
DO NOT SLIDE BED AFTER
ASSEMBLY. LIFT THE BED FRAME
INTO ITS FINAL POSITION.
1 pc
W
( L )
( R )
W
W
( L )
( R )
( L )
( R )
Team
Assembly
Recommended
4 pcs
M8X20
J
8 pcs
M6X30
K
10 pcs
M6X50
L
8 pcs
M6X60
M
20 pcs
M4X32
N

1.
( L )
( R )
W
W
A ach (P) and (O) washers to (L) bolts. Use the (L) bolts to
connect the wing (W) to the ends of the headboard (A).
Tighten the (L) bolts with Allen key (Q).
L
P
O
A
4 pcsM6X50
+P
L+O
Q

2.
Thread footboard legs (F) to
bo om of footboard panel (C).

4 pcs
M8X20
J
3.
Thread (J) bolts into the holes in the
footboard. Do not ghten. These will be
ghtened in later steps.
J
R

K
O
8 pcs
M6X30
+
KO
D
E
E
4.
Repeat steps to assemble right side rail.
A ach (O) washers to (K) bolts.
Connect the top and bo om of each
side rail with a (D) side leg.
Use the bolts to a ach. Tighten the
bolts (K) with Allen key (Q).
Q
This end will a ach
to footboard (C).
( Figure shown in le side rail)
This end will a ach
to wing (W).

( L )
( R )
J
R
Hang the hooks at the ends of the side rails
onto the (J) bolts in the footboard. Tighten the
(J) bolts with Allen key (R).
5.
E
E

A ach (P) and (O) washers to (L) bolts.
Use the (L) bolts to connect the ends of
the side rails to the wings (W). Tighten
the (L) bolts with Allen key (Q).
( L )
( R )
NOTE:
Do not a empt to slide the bed once it is fully
assembled. Sliding the bed could result in
damage to the rails, headboard, or footboard.
Assembled bed should be lied and carried
when being moved (not slid).
6.
6 pcsM6X50
+P
L+O
OPL
WE
A
E
E
Q

8 pcs
M6X60
M
M
7.
Aer the slat system is assembled, place the slats
into the frame of the bed as shown in next page.
Repeat steps to assemble the second roll slat.
Assemble the slat system by a aching the slats (G)
to the (I) supports and (H) legs. First, extend the
slats. Then, line up the holes in the slats with the
holes in the (I) supports and the holes in the tops
of the (H) legs. Use an (M) bolt through the holes to
a ach them together. Tighten with Allen key (Q).
Q

8.
NEED ADDITIONAL HELP?
Email our support team: [email protected]o
Floor line
Floor Glide
The center support leg glide sits approximately
1/4" off of the floor. The glide will usually touch
the floor aer a ma ress is placed on the
bedframe.
NOTE:
Do not place a ma ress on bedframe unl it is
fully assembled and ghtened. The bedframe
should be located in your desired locaon. Sliding
the bed with weight upon it can compromise the
integrity of the center support legs.
20 pcs
M4X32
N
N
Use screwdriver to install
(N) screws into side rail
cleats to a ach slats.