OWI Salt Water Fuel Cell Engine Car kit Installation guide

Assembly & Instruction
Manual
GREEN ENERGY

P.01
P.01
P.02
CONTENTS
Tools You May Need
Mechanical Parts List
Plastic Parts
P.03
Mechanical Assembly
P.17
P.21
How It Works
How To Play
P.23
Trouble Shooting

Tools You May Need
Mechanical Parts List
QTY
1
P1 Motor With
Connectors
QTY
1
P2 Pinion Gear
(Yellow)
QTY
1
P3 Gear (Yellow)
Stick Diagonal CutterSalt
Salt
Cup
P1
All materials used in this kit are
environmentally safe and clean, no toxic
substances or disposal concerns.
GREEN ENERGY
Screwdriver
Screwdriver
This is a concept of an environmentally
and friendly fuel cell engine car kit. The kit
will teach children about new forms of
clean energy. Be amazed that just by
adding a few drops of salt water the car’s
engine will start to run as if by magic. See
how a V8 engine runs. There are other
exciting activities to explore.
Don't connect the
wires to the mains.

QTY
1
P7
QTY
1
P8 Plastic dropperMagnesium Sheet
Plastic Parts
QTY
1
P4
QTY
1
P5
Gear(Red)
QTY
1
P6
Round Shaft
QTY
1
P7
QTY
2
P8
QTY
1
P9
(Spare part:1pc)
Tapping Screw
QTY
1
P10
QTY
1
P11
Air Cathode(Black) Nonwoven Fabric
(Spare parts:2pcs)
Magnesium sheet
QTY
1
P13 Plastic Dropper
QTY
1
P12
P2
Gear With Shaft
Magnesium Sheet
C
1
2
3 4
7
6
7
7 7
8
5
D1
Cut the plastic parts when they are required . Do not cut them in advance.
Crown Gear With Shaft
Gear Shaft W/Pinions

Mechanical Assembly
P3
1
STEP
P7
P6
P4
P3
P5
A2
P8
A
1
23
4
5
6666
87
1 2 3
4 4 7
8 9
10
151514
16 17
5 6
15
13
11
12
13 15
B

P4
2
STEP
P1
P2

A3
A5
P5
3
STEP
B3
C5
C5 A5
B3
C5
C5

P6
4
STEP
B16
C2
B17
C1
Red
Black
B17
B16
B16
B16
Connector
Module
Connector
Module

P7
5
STEP
x4
A8
B13
A7
B2
B9
C8
x4
B13 A7
A8
B7
B10
C6
2
2
1
1
2
1
2
1

P8
6
STEP
7
STEP
B8
B1
Top View
B11
B11
8
STEP

9
STEP
P9
B5
B6
P9
A4 A4
10
STEP
Make sure the P10,P11,P12 placed in correct sequence and position.
Black
Side Up
P10
(Air Cathode)
P12
(Magnesium Sheet)
Cut off the 2 burrs
before assembly.
P11 (Nonwoven Fabric)
Scratch here before
assembly.
P12
Magnesium
Sheet
C3

11
STEP
P10
B12
B14
B14
B12
P8
Fuel Cell
Plate
1
2
C4
12
STEP
Side View
Side View

Be sure to insert fuel cell plate and
connector module to the end.
P11
13
STEP
B4
B4
1
1
2
Fuel Cell
Plate
Connector
Module
Connector
Module
Red
Black

P12
14
STEP
15
STEP
x4
A6
D1

P13
16
STEP
C7
C7

P14
17
STEP
B15
A1
B15
A1

P15
18
STEP
C7
C7

P16
19
STEP
B15
A1
B15
A1
Finished product!

Remove Fuel Cell plate Remove cover and
magnesium sheet Add salt water on nonwoven fabric
How It Works
a. b. c.
2How to fill the engine car with salt water:
Water
Salt
P17
After a period of time the salt water will be exhausted ( about 15 minutes ), the car will
begin to get slower or stop. Add a few more drops of salt water to start it again
( as in fig 3)
Each Magnesium sheet can work for 4 hours continuously, then it will become fragmented.
Replace the sheet with a new one to energize the car. The kit includes 3 refills.
All materials used in this kit are environmentally safe and clean, no toxic substances or
disposal concerns.
Please pay full attention to the below mentioned before use!
1How to make salt water solution: Add salt to tap water or distilled water at
ratio of 1(salt) : 5(water). Any percentage ratio from 20% to 99% salt water is
workable although the 20% will be the most efficient.
Do not add salt water
outside nonwoven fabric
as shown below.
Cover
Magnesium
Sheet
Nonwoven
Fabric

Reassemble cover and
magnesium sheet Insert Fuel Cell plate
d. e. f.
3How to refill the salt water : When the engine car starts getting slower or stops,
reapply a few drops of salt water with the applicator into the position as shown 2C.
And scratch oxide from the battery connectors and also magnesium sheet by slotted
screwdriver before reuse. See below figures:
Run your car now
g.
P18
Make sure the polarity of the
connector dry without salt water
Scratch Here
P1
Connector
P12
Magnesium
Sheet
Front Side
The Opposite Side
Scratch Here
Cover
Magnesium
Sheet