OYPLA DIY 3828 User manual

Page 1
Model Code: 3828, 3829, 3830, 3662, 3663
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 3828,
3829, 3830, 3662, 3663
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
5Back Cover
End
Plastic Shelving
*Size will vary depending on model purchased

Page 2
Model Code: 3828, 3829, 3830, 3662, 3663
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
5Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
This product is not a toy, and is only to
be used for its designated purpose.
This product is intended for indoor use
only.
Never carry out alterations or
modifications to this product.
Make sure to load the platform evenly
where possible, ensuring that the weight
is balanced.
Do not discard any of the packaging until
you have checked that you have all the
parts required.
Never climb on the shelves, and never
allow children/pets to climb on them
either.
Leaving the product outside and exposed
to weather, especially direct sunlight,
rain and salt air, will speed the
weathering process. This can be slowed
by removing the product from these
conditions, or covering the product with
a suitable cover.
Make sure that the plastic shelving is
placed on even ground to avoid the
product failing when items are placed on
it.
If the product is damaged or has any
defects, please contact
[email protected]
⚠The weight capacity of each shelf is 20kg. Do not exceed this amount, as
doing so may result in product failure and/or personal injury.
Warning

Page 3
Model Code: 3828, 3829, 3830, 3662, 3663
Oypla.com LLP / www.oypla.com
Parts List:
-If you are missing any of the below parts, please contact [email protected]
-Please be aware that you will be referring to this parts list throughout the assembly
process.
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
5Back Cover
End
Assembly Instructions
1. Lay the plastic platform on a flat surface so the underside is facing
upwards. Once done, push a rack foot into the plastic platform. Make sure
that the rack foot is as far in as possible to avoid the rack foot coming
loose whilst the plastic shelving is in use. Repeat with remaining rack feet.

Page 4
Model Code: 3828, 3829, 3830, 3662, 3663
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
5Back Cover
End
2. Turn over the plastic platform that has the feet attached and push a
rack support pole into the hole in the upside of the plastic platform.
Repeat this for the remaining holes. Once done, place another plastic
platform on top of the rack support poles. Make sure the plastic platform
is held securely in place. If you wish for the racking to go higher, simply
repeat this step to create more racking platforms.
3. Once you’ve reached the desired height for your plastic shelving, simply
push a platform plug into the holes on the top plastic platform. Once
done, be sure to test the stability of the plastic shelving by placing an
object of considerable weight on it. Never exceed the 20kg shelf capacity
limit.

Page 5
Model Code: 3828, 3829, 3830, 3662, 3663
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
5Back Cover
End
Imported by Oypla.com LLP, Uxbridge, UX8 2FX