OYPLA DIY Heavy Duty 5 3661 User manual

Page 1
Manual Version: v1.0
Model Code: 3661
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 3661
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
-
2Assembly
Instructions
-
4Back Cover
End
Heavy Duty 5
Tier Shelving

Page 2
Manual Version: v1.0
Model Code: 3661
Oypla.com LLP / www.oypla.com
Parts List:
-If you are missing any of the below parts, please contact [email protected]
-Please be aware that you will be referring to this parts list throughout the assembly
process.
PARTS LIST CONTINUES ON FOLLOWING PAGE
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
-
2Assembly
Instructions
-
4Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
This product is not a toy, and should only
be used for its designated purpose.
Make sure that the racking platforms are
secure before applying any weight to
them.
Only use this product on stable, level and
dry ground.
Leaving this product outside exposed to
weather, especially direct sun, rain and
salt air, will speed the weathering
process. This can be slowed by removing
the product from these conditions, or
covering it with a suitable cover.
This product contains sharp parts. Be
careful and ensure appropriate PPE is
worn during assembly and use.
Do not carry out alterations or
modifications to this product.
Do not discard any of the packaging until
you have checked that you have all of
the parts and fittings required.
When adjusting the height of the
shelves, be sure that the shelving is
securely held in place after adjusting the
height, to avoid it falling due to weight
application.
Clean only with a damp cloth. Do not use
any strong industrial cleaning substances
or abrasive materials, as these may
damage the product.
If the product is damaged or defective,
please contact cserv[email protected]
Assembly Instructions
⚠Do not overload the shelves! The maximum capacity for each shelf is
150kg, and the overall weight capacity is 750kg.
⚠Ensure appropriate PPE is worn at all times. This product contains
sharp parts that could cause personal injury.
Warning

Page 3
Manual Version: v1.0
Model Code: 3661
Oypla.com LLP / www.oypla.com
*The use of a rubber mallet can be very helpful when assembling these shelves, to
help gently press the parts together.
Take an upright support (Part B) and
connect a long horizontal support (part E)
by placing the tongue through the hole
and pushing down. Once you have
completed this, grab another upright
support (part B) and connect onto the
other end, then connect a short
horizontal support (part C) and repeat
this until you have a base to place the
shelf (part A).
Repeat the steps from
step 1 until you have
completed three
layers of shelving.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
-
2Assembly
Instructions
-
4Back Cover
End
1
2

Page 4
Manual Version: v1.0
Model Code: 3661
Oypla.com LLP / www.oypla.com
When connecting the final two tiers, use a
long horizontal support (part E) and use
one tongue on each of the top and
bottom upright support. (Use the boxed
image to the right for reference). When
you have completed this on all sides,
follow the previous steps in order to
assemble the last half.
Once the shelves are fully assembled,
place one support cap (part D) on each of
the ends of the upright supports (part B).
This will cover the tops and bottoms and
give a form of protection across the thin
metal pieces. Once all caps are placed,
the product is fully assembled.
Contents
1Front Cover
-
2Safety
Instructions
-
2Warning
-
2Assembly
Instructions
-
4Back Cover
End
3