OYPLA Home 4745 User manual

Page 1
Manual Version: V1.0
Model Code: 4745/4746
Oypla.com LLP / www.oypla.com
User Manual
Model Code:
4745/4746
Set of 3 Floating
Shelves
Contents
1 Front Cover
2 Safety
Instructions
2 Assembly
Instructions
3 Back Cover
*COLOUR MAY VARY

Page 2
Manual Version: V1.0
Model Code: 4745/4746
Oypla.com LLP / www.oypla.com
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
-Read these instructions carefully and familiarise yourself with the procedure before
assembling the unit. Keep these instructions for future use.
-Check that you have all the component parts following the list above and familiarise
yourself with each part before proceeding.
-Make sure all fastenings are tightly in place before using this product. This should be
checked periodically by an adult.
-This product is intended for indoor use only.
-This product is not a toy, and is only to be used for its designated purpose.
-This product contains small parts that could be a choking hazard if swallowed. Keep
these items away from children.
-Do not discard any of the packaging until you have checked that you have all of the
parts and fittings required.
-Use the correct fixings as indicated. Do not overtighten any fixings.
-Keep product away from fire.
-Clean only using a damp cloth. Do not use strong industrial cleaning substances, as
these may damage the product.
-Before drilling holes in any walls or surfaces, ensure to check there are no hidden pipes
or cables.
-Do not overload the shelves. (5kg limit per shelf).
-If the product is damaged or has any defects, please contact cservic[email protected]
Contents
1 Front Cover
2 Safety
Instructions
2 Assembly
Instructions
3 Back Cover
Assembly Instructions
Parts List:
If you are missing any of the below parts, please contact [e-mail]
PLEASE NOTE ALL QUANTITIES ARE “PER SHELF”
A
B
C
D
E
F

Page 3
Manual Version: V1.0
Model Code: 4745/4746
Oypla.com LLP / www.oypla.com
Contents
1 Front Cover
2 Safety
Instructions
2 Assembly
Instructions
3 Back Cover
1. Using two bolts provided
(C), and the Allen key (D)
attach the shelf side (B) to
the main part of the shelf (A).
Repeat this for the other side
of the shelf. Repeat this
process for each shelf.
Important: Before mounting the shelves, ensure you have checked for pipes and cables that may be hidden in the
wall or mounting surface. Do not mount the shelves on areas where pipes and/or cables lay.
Before drilling holes, ensure to lightly mark the hole locations with a pencil. We recommend using a spirit level whilst
holding the shelf up to the wall, to ensure the shelf is perfectly level. Once you are happy with the hole locations, you
can proceed to drill the holes, as shown below.
2. Proceed to drill the desired holes. Ensure to not exceed the length of the
screw. You may want to use masking tape attached to the drill bit to ensure
you do not drill too deep. Do not use a drill bit that is wider than the wall
plugs that are provided for mounting.
3. Insert the wall plugs provided (E) into the holes you have created. A hammer
can be used to lightly tap the end of the plugs to ensure they are fully inserted.
4. Insert the screws provided (F) into the holes, now with wall plugs in. Do
not drill the screws all the way in –leave enough of an overhang for the
shelves to attach to.
5. When both screws are inserted sufficiently, hang the shelf onto them.
Repeat this process for all 3 shelves.
Imported by Oypla.com LLP, Uxbridge, UB8 2FX