Oypla 2458 User manual

User Manual
USER MANUAL Model No: 2458
Garden Tipping Trolley

Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold on
this condition, which no representative of the company can waive or change.
•This product contains small parts that could be a choking hazard if swallowed.
Keep these items away from children.
•If at any time during activity you feel faint, dizzy or experience pain, stop and
consult your physician or doctor.
•Make sure all fastenings are tightly in place and that everything is in order before
using the product. This should be checked periodically by an adult.
•Do not overload the product. When transporting a heavy load, be careful when
changing directions as the cart could easily tip over if moving too quickly.
•This product is intended for outdoor use only.
•This product is not a toy, and is only to be used for its designated purpose.
•Do not carry out alterations or modifications to this product.
•Clean only with a damp cloth. Do not use strong industrial cleaning substances.
•Leaving the product outside exposed to weather, especially direct sun and rain,
will speed the weathering process. This can be slowed by removing the product
from these conditions, or covering it with a suitable cover.
•Pinch points can cause personal injury.
•Do not discard any of the packaging until you have checked that you have all of the
parts and fittings required.
•Use the correct fixings as indicated. Do not tighten any of the nuts until the unit is
completely assembled, then finish by tightening all nuts. All nuts must be
tightened before use.
•Keep away from fire.
•If the product is damaged or has any defects, please contact [e-mail].
USER MANUAL Model No: 2458

Assembly Instructions
Parts List:
If you are missing any of the below parts please contact [e-mail]
Please be aware that you will be referring to this parts list throughout the assembly process.
Tub (1pc)
A
Frame (1pc)
B
Handle (1pc)
C
Lock Frame
(1pc)
D
Rear axle
frame with
rear struts
(1pc)
E
Front axle
support with
braces
(1pc)
F
Handle
coupler
(1pc)
G
Wheels
(4pcs)
H
Small bolt
(14pcs)
I
Small bolt
washers
(14pcs)
J
Large locking
nut
(4pcs)
K
Gasket
(4pcs)
L
Long bolt
(1pc)
M
Long Bolt
washer
(1pc)
N
USER MANUAL Model No: 2458

1. Grab the barrow tub (A) and place it upside down on a flat
surface. Then grab the frame (B) and align the holes on the tub
and the frame and secure using one bolt on each side (I).
2. Next grab the front axle support with braces (G), and place it on
the opposite end to where you attached the tub to the frame. Use
six bolts (I) and 6 small bolt washers (J) to secure this onto the
frame.
3. Attach the Front axle support with braces (F) to the frame (B)
using 4 small bolts (I) and 4 small bolt washers (J).

4. Next attach the lock frame (D) onto the barrow tub (A)
using 4 bolts (I) and 4 small bolt washers (J).
6. Attach the 4 wheels (H) to each axle bar, and secure this by
using 4 gaskets (L) and the large locking nut (K).
5. Slide the handle (C) into the handle coupler (G), and then
attach this into the front axle support with braces (F). Make
sure the holes of the handle and the coupler line up and secure
using 1 long bolt (M) and long bolt washer (N).
USER MANUAL Model No: 2458

Tipping the plastic tray
-On the lock mechanism, pull the handle to release the lock and lift upwards.
Lowering the plastic tray
-Slowly push the plastic tray down. Pull the handle and release back into the locking holes.
Imported by Oypla.com LLP, Uxbridge, UB8 2FX
USER MANUAL Model No: 2458