Ozito TRP-650 User manual

TRANSFER
WATER PUMP
600W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 600W
Max. Flow Rate: 3,600l/h
Max. Lift 8m
Max. Head: 40m
Outlet & Inlet: 25mm (1”)Female
Max. Delivery Pressure: 4.0 bar
Water Temp.: 1°C - 35°C
Hmin=: 2m
Weight: 10kg
TRP-650
WHAT’S IN THE BOX
Transfer Water Pump
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: O-rings, bearing, seals gaskets.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
INSTALLATION
TROUBLESHOOTING
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1113
WARNING! The input hose or pipe should be low enough in the water to ensure that if the
water level falls, the pump will not run dry. Ensure that this is checked when in operation.
NOTE: A leaking hose or pipe will draw in air and therefore not draw in any water.
Positioning the Hose or Pipe
Position the input hose or pipe so that it rises from the water drawing source to the pump. Avoid
positioning the input hose or pipe higher than the pump, as this would delay the escape of air
bubbles from the input hose or pipe and impede the priming process (see section ‘starting the
pump’ for description on priming the pump)
Problem Possible Cause Solution
The pump does not start,
or pump water
Pump is not connected to the power supply
Pump is blocked
Pump is not connected to the water supply
Check that the pump is connected to the mains power supply
Disconnect the pump from the mains power. Inspect the discharge outlet and lter
Ensure the pump is connected to the water supply
The pump does not supply water
when the motor is running
The pump has not been primed
Suction line is leaking
The pump is sucking air
Pump is blocked
Pump is not producing enough pressure
Water source does not have enough water
The suction height is too high
The hose diameter is too small
Fill the pump with water, ensure the suction line and pump are lled with water
Check the suction line for leaks and replace hose or pipe if it is damaged or worn
Ensure all connections and ttings are secured tightly
Disconnect the mains power and check the discharge outlet and lter for any foreign matter
Check all parts of the pump and clean
Wait until the water source increases so the pump can operate
Ensure the suction height is no higher than 8m
Ensure the hose diameter is at least 25mm (suction line) and 19mm (discharge line)
Tube or piping does not stay on
the male thread when water is
travelling through
The hose or tubing may be worn or vary
slightly with the dimensions
Add a hose clamp to prevent leaks and secure the hose or pipe
The pump operates intermittently
There is a water leak in the household
plumbing
The voltage is out of range
Air ow is not allowing the motor to cool
The motor is faulty or damaged l
Inspect and x any leaks
Supply the pump in accordance with the rating label requirements
(230-240V)
Ensure the pump is in a well ventilated area
Contact Ozito customer service
Poor Performance
low pressure ow
Faulty suction line Check all the suction lines for leaks or any damage. Replace if they are faulty and check that
you are using a reinforced hose to prevent the hose from collapsing
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landll and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486 New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
ADDITIONAL SAFETY INSTRUCTIONS FOR PUMPS
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save these instructions
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepumpsinexplosiveatmospheres,suchasinthepresenceofammableliquids,
gases or dust. Pumps create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a pump. Distractions can cause you to lose control.\
2. Electrical safety
a. Pump plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) pumps. Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the pump. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
d. When operating a pump, use an extension cord suitable for wet conditions. Use of a cord suitable for
wet use reduces the risk of electric shock.
e. If operating a pump, use a residual current device (RCD) protected supply. Use of an RCD reduces the
risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a pump. Do not use
apumpwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A moment of
inattention while operating a pump may result in serious personal injury.
b. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying pump
with your nger on the switch or plugging in pumps that have the switch on invites accidents.
c. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
d. When operating a pump outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4. Pump use and care
a. Disconnect the plug from the power source before making any adjustments, changing accessories,or
storing pumps. Such preventive safety measures reduce the risk of starting the pump accidentally.
b. Maintain pumps. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the pumps operation. If damaged, have the pump repaired before use. Many
accidents are caused by poorly maintained pumps.
c. Use the pump, and accessories etc., in accordance with these instructions and in the manner
intended for the particular type of pump, taking into account the working conditions and the work to
be performed. Use of the pump for operations different from intended could result in a hazardous situation.
5. Service
a. Haveyourpumpservicedbyaqualiedrepairpersonusingonlyidenticalreplacementparts.This will
ensure that the safety of the pump is maintained.
b. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
GENERAL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING! This product is intended for pumping water in a Home Domestic application.
Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than water
willdamagethewaterpumpand/orcreatearehazard.Failuretofollowallinstructionslisted
belowmayresultinelectricshock,reand/orseriousinjury.
WARNING! This product is not suitable for use with drinking (potable) water.
This appliance is not intended for use by person (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Ensurethewaterpumpisdisconnectedfrommainspowerwheninstalling.
• Donotinstalloroperatethewaterpumpinanexplosiveenvironmentornearammablematerial.
• Donotoperatethewaterpumpwithoutliquid.
• Donotrunthewaterpumpdry.
WARNING! The water pump together with associated pipework operate under pressure. Do not
disconnect water pump or pipework until internal pressure has been released. Failure to do this
could result in personal injury and damage to property.
• Avoid inserting hands into the inlets/outlets of the water pump while it is connected to power.
• Before using the water pump, always inspect it visually. Do not use the pump if it is cracked and/or damaged.
If the water pump is damaged, contact Ozito customer service.
• The water pump has a built-in thermal protection overload switch. The water pump stops if an overload
occurs. The motor restarts automatically after it has cooled down.
• The pump must not be used when people are in the water.
• Never work or perform maintenance on the pump without rst making sure it has been disconnected from the
mains power.
• Pollution of the liquid could occur due to leakage of lubricants Important:
Avoid inserting hands into the mouth of the pump if it is connected to the mains.
The electrical connection must always be made in a dry area. Make sure that electrical connections are protected
from inundations.
Protect the plug and the power cable from heat, oil or sharp edges.
If damaged, The power cable must be replaced by a qualied electrician.
WARNING! When using mains-powered tools, basic safety precautions, including the
following,shouldalwaysbefollowedtoreduceriskofre,electricshock,personalinjuryand
material damage.
Read and understand the manual prior to operating this pump.
Save these instructions and other documents supplied with this pump for future reference. The electric motor has
been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the
rating plate.
Note: The supply of 230V and 240V on Ozito pumps are interchangeable for Australia and New Zealand. This
pump is earthed in accordance with AS/NZS 60335-2-41.
Note: The power outlet used for the water pump is recommended to be protected by a 30mA residual current
device or earth leakage circuit breaker. If the power outlet is external, ensure that it is weather proof. If the supply
cord is damaged, it must be replaced by an electrician or a power tool repairer to avoid a hazard. The water pump
has a built-in thermal protection overload switch. The water pump stops if an overload occurs. The motor restarts
automatically after it has cooled down.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this product. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. Then
using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for
the power input of this product or which is damaged or defective may result in a risk of re and electric shock.
V Volts Hz Hertz
~ Alternating current WWatts
/min Revolutions or noNo load speed
reciprocation per minute
l Litres ºC Degrees celsius
p/hr Per hour kPa Pressure rating (kilopascals)
bar Pressure rating FInsulation class
PVCPolyvinyl chloride IPX8 Ingress protection from water
Regulator compliance mark Warning
Read instruction manual
150mm
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
SUCTION LINE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE BELOW WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE
SUCTIONLINE
WATERTANK
GATE
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
UNION
COUPLING
depending
on installation
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
150mm
mm051
SUCTIONLINE
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Turn the pump on at the
mains power.
2. Depress the ON/OFF
switch to the ON ( l ) position
3. To turn the pump off, depress the ON/OFF switch to the OFF (0)
position.
2. Using a spanner or
screwdriver remove the
priming screw from the top
of the pump housing by
turning the screw counter
clockwise.
3. Using a hose,  ll the pump
completely with water.
Ensure the pump and
inlet pipe or hose are full.
Replace the priming screw.
1 Ensure the pump’s on/off switch is in the off (0) position and off at
the mains power. 1 Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from
bad weather conditions.
2 .Before storing the pump. It is recommended to drain the pump.
Turn the drain plug anti-clockwise and remove from the pump.
This will drain any excess water. Replace the drain plug by turning
clockwise
1. Induction Motor
2. Electrical Box
3 Adjustable Foot
4 Carry Handle
5 Pumping Housing
6 Discharge Outlet
7 Priming Screw
8 Drain Plug
9 Suction Inlet
TRANSFER PUMP
KNOW YOUR PRODUCT
TRP-650
1. SUCTION INLET 2. DISCHARGE OUTLET 3. PRIMING THE PUMP 4. OPERATING THE PUMP 5. MAINTENANCE & STORAGE
Preparing the Pump: Your pump requires no assembly before
use other than the connection of a suitable inlet/outlet hose and
hose connections (not included).
3. Securely attach the output
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water.
discharge application.
2. Remove the plastic protection
cover from the discharge outlet
and insert a 1” male threaded
hose adaptor (not included)..
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
NOTE: The input hose or pipe you are using must
have a minimum diameter of 25.4mm (1’’).
NOTE: Ensure the input hose or pipe is not
restricted in any way.
NOTE: The discharge hose or pipe you are using
must have a minimum diameter of 19mm (3/4’’).
NOTE: Ensure the discharge hose or pipe is not
restricted in any way and no pressure is obstructing
the hose or pipe when the pump is in operation.
SETUP & PREPARATION OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
NOTE: Whenthepumpisfullyprimedandairisushed
out , the pump is ready to operate. The pump may take
several minutes to fully prime air from inside the pump
and inlet pipe or hose.
The pump is recommended for use with a residual current
device with a rated residual current of 30mA or less.
Make sure the pump is disconnected from electric power
supply before performing maintenance procedures.
2. Remove the plastic protection
cover from the suction inlet
and insert a 1” male threaded
hose adaptor (not included).
Tighten  rmly with a spanner (not
included).
3. Securely attach the input hose
or pipe to the other end of the
adaptor. Ensure you have the
correct diameter hose or pipe
that is compatible with your water
drawing source.
Connecting Hose or Pipe to the
Suction Inlet
1. Te on tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind Te on clockwise on
 ttings
1. Te on tape (not included) is
required on threads to ensure
a water tight seal and prevent
any leakage. Wind Te on
clockwise on  ttings
Ensure the pump is disconnected from the power supply
before performing any of the following operations.
Remove drain
plug & allow
water to drain
out
Slowly  ll
with water
Connecting Hose or Pipe to the Discharge Outlet
NOTE: Ensure the gate valve on your water tank is not left open as
this will allow water to drain from the water tank.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Turn the pump on at the
mains power.
2. Depress the ON/OFF
switch to the ON ( l ) position
3. To turn the pump off, depress the ON/OFF switch to the OFF (0)
position.
2. Using a spanner or
screwdriver remove the
priming screw from the top
of the pump housing by
turning the screw counter
clockwise.
3. Using a hose,  ll the pump
completely with water.
Ensure the pump and
inlet pipe or hose are full.
Replace the priming screw.
1 Ensure the pump’s on/off switch is in the off (0) position and off at
the mains power. 1 Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from
bad weather conditions.
2 .Before storing the pump. It is recommended to drain the pump.
Turn the drain plug anti-clockwise and remove from the pump.
This will drain any excess water. Replace the drain plug by turning
clockwise
1. Induction Motor
2. Electrical Box
3 Adjustable Foot
4 Carry Handle
5 Pumping Housing
6 Discharge Outlet
7 Priming Screw
8 Drain Plug
9 Suction Inlet
TRANSFER PUMP
KNOW YOUR PRODUCT
TRP-650
1. SUCTION INLET 2. DISCHARGE OUTLET 3. PRIMING THE PUMP 4. OPERATING THE PUMP 5. MAINTENANCE & STORAGE
Preparing the Pump: Your pump requires no assembly before
use other than the connection of a suitable inlet/outlet hose and
hose connections (not included).
3. Securely attach the output
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water.
discharge application.
2. Remove the plastic protection
cover from the discharge outlet
and insert a 1” male threaded
hose adaptor (not included)..
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
NOTE: The input hose or pipe you are using must
have a minimum diameter of 25.4mm (1’’).
NOTE: Ensure the input hose or pipe is not
restricted in any way.
NOTE: The discharge hose or pipe you are using
must have a minimum diameter of 19mm (3/4’’).
NOTE: Ensure the discharge hose or pipe is not
restricted in any way and no pressure is obstructing
the hose or pipe when the pump is in operation.
SETUP & PREPARATION OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
NOTE: Whenthepumpisfullyprimedandairisushed
out , the pump is ready to operate. The pump may take
several minutes to fully prime air from inside the pump
and inlet pipe or hose.
The pump is recommended for use with a residual current
device with a rated residual current of 30mA or less.
Make sure the pump is disconnected from electric power
supply before performing maintenance procedures.
2. Remove the plastic protection
cover from the suction inlet
and insert a 1” male threaded
hose adaptor (not included).
Tighten  rmly with a spanner (not
included).
3. Securely attach the input hose
or pipe to the other end of the
adaptor. Ensure you have the
correct diameter hose or pipe
that is compatible with your water
drawing source.
Connecting Hose or Pipe to the
Suction Inlet
1. Te on tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind Te on clockwise on
 ttings
1. Te on tape (not included) is
required on threads to ensure
a water tight seal and prevent
any leakage. Wind Te on
clockwise on  ttings
Ensure the pump is disconnected from the power supply
before performing any of the following operations.
Remove drain
plug & allow
water to drain
out
Slowly  ll
with water
Connecting Hose or Pipe to the Discharge Outlet
NOTE: Ensure the gate valve on your water tank is not left open as
this will allow water to drain from the water tank.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Turn the pump on at the
mains power.
2. Depress the ON/OFF
switch to the ON ( l ) position
3. To turn the pump off, depress the ON/OFF switch to the OFF (0)
position.
2. Using a spanner or
screwdriver remove the
priming screw from the top
of the pump housing by
turning the screw counter
clockwise.
3. Using a hose,  ll the pump
completely with water.
Ensure the pump and
inlet pipe or hose are full.
Replace the priming screw.
1 Ensure the pump’s on/off switch is in the off (0) position and off at
the mains power. 1 Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from
bad weather conditions.
2 .Before storing the pump. It is recommended to drain the pump.
Turn the drain plug anti-clockwise and remove from the pump.
This will drain any excess water. Replace the drain plug by turning
clockwise
1. Induction Motor
2. Electrical Box
3 Adjustable Foot
4 Carry Handle
5 Pumping Housing
6 Discharge Outlet
7 Priming Screw
8 Drain Plug
9 Suction Inlet
TRANSFER PUMP
KNOW YOUR PRODUCT
TRP-650
1. SUCTION INLET 2. DISCHARGE OUTLET 3. PRIMING THE PUMP 4. OPERATING THE PUMP 5. MAINTENANCE & STORAGE
Preparing the Pump: Your pump requires no assembly before
use other than the connection of a suitable inlet/outlet hose and
hose connections (not included).
3. Securely attach the output
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water.
discharge application.
2. Remove the plastic protection
cover from the discharge outlet
and insert a 1” male threaded
hose adaptor (not included)..
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
NOTE: The input hose or pipe you are using must
have a minimum diameter of 25.4mm (1’’).
NOTE: Ensure the input hose or pipe is not
restricted in any way.
NOTE: The discharge hose or pipe you are using
must have a minimum diameter of 19mm (3/4’’).
NOTE: Ensure the discharge hose or pipe is not
restricted in any way and no pressure is obstructing
the hose or pipe when the pump is in operation.
SETUP & PREPARATION OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
NOTE: Whenthepumpisfullyprimedandairisushed
out , the pump is ready to operate. The pump may take
several minutes to fully prime air from inside the pump
and inlet pipe or hose.
The pump is recommended for use with a residual current
device with a rated residual current of 30mA or less.
Make sure the pump is disconnected from electric power
supply before performing maintenance procedures.
2. Remove the plastic protection
cover from the suction inlet
and insert a 1” male threaded
hose adaptor (not included).
Tighten  rmly with a spanner (not
included).
3. Securely attach the input hose
or pipe to the other end of the
adaptor. Ensure you have the
correct diameter hose or pipe
that is compatible with your water
drawing source.
Connecting Hose or Pipe to the
Suction Inlet
1. Te on tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind Te on clockwise on
 ttings
1. Te on tape (not included) is
required on threads to ensure
a water tight seal and prevent
any leakage. Wind Te on
clockwise on  ttings
Ensure the pump is disconnected from the power supply
before performing any of the following operations.
Remove drain
plug & allow
water to drain
out
Slowly  ll
with water
Connecting Hose or Pipe to the Discharge Outlet
NOTE: Ensure the gate valve on your water tank is not left open as
this will allow water to drain from the water tank.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Turn the pump on at the
mains power.
2. Depress the ON/OFF
switch to the ON ( l ) position
3. To turn the pump off, depress the ON/OFF switch to the OFF (0)
position.
2. Using a spanner or
screwdriver remove the
priming screw from the top
of the pump housing by
turning the screw counter
clockwise.
3. Using a hose,  ll the pump
completely with water.
Ensure the pump and
inlet pipe or hose are full.
Replace the priming screw.
1 Ensure the pump’s on/off switch is in the off (0) position and off at
the mains power. 1 Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from
bad weather conditions.
2 .Before storing the pump. It is recommended to drain the pump.
Turn the drain plug anti-clockwise and remove from the pump.
This will drain any excess water. Replace the drain plug by turning
clockwise
1. Induction Motor
2. Electrical Box
3 Adjustable Foot
4 Carry Handle
5 Pumping Housing
6 Discharge Outlet
7 Priming Screw
8 Drain Plug
9 Suction Inlet
TRANSFER PUMP
KNOW YOUR PRODUCT
TRP-650
1. SUCTION INLET 2. DISCHARGE OUTLET 3. PRIMING THE PUMP 4. OPERATING THE PUMP 5. MAINTENANCE & STORAGE
Preparing the Pump: Your pump requires no assembly before
use other than the connection of a suitable inlet/outlet hose and
hose connections (not included).
3. Securely attach the output
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water.
discharge application.
2. Remove the plastic protection
cover from the discharge outlet
and insert a 1” male threaded
hose adaptor (not included)..
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
NOTE: The input hose or pipe you are using must
have a minimum diameter of 25.4mm (1’’).
NOTE: Ensure the input hose or pipe is not
restricted in any way.
NOTE: The discharge hose or pipe you are using
must have a minimum diameter of 19mm (3/4’’).
NOTE: Ensure the discharge hose or pipe is not
restricted in any way and no pressure is obstructing
the hose or pipe when the pump is in operation.
SETUP & PREPARATION OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
NOTE: Whenthepumpisfullyprimedandairisushed
out , the pump is ready to operate. The pump may take
several minutes to fully prime air from inside the pump
and inlet pipe or hose.
The pump is recommended for use with a residual current
device with a rated residual current of 30mA or less.
Make sure the pump is disconnected from electric power
supply before performing maintenance procedures.
2. Remove the plastic protection
cover from the suction inlet
and insert a 1” male threaded
hose adaptor (not included).
Tighten  rmly with a spanner (not
included).
3. Securely attach the input hose
or pipe to the other end of the
adaptor. Ensure you have the
correct diameter hose or pipe
that is compatible with your water
drawing source.
Connecting Hose or Pipe to the
Suction Inlet
1. Te on tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind Te on clockwise on
 ttings
1. Te on tape (not included) is
required on threads to ensure
a water tight seal and prevent
any leakage. Wind Te on
clockwise on  ttings
Ensure the pump is disconnected from the power supply
before performing any of the following operations.
Remove drain
plug & allow
water to drain
out
Slowly  ll
with water
Connecting Hose or Pipe to the Discharge Outlet
NOTE: Ensure the gate valve on your water tank is not left open as
this will allow water to drain from the water tank.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Turn the pump on at the
mains power.
2. Depress the ON/OFF
switch to the ON ( l ) position
3. To turn the pump off, depress the ON/OFF switch to the OFF (0)
position.
2. Using a spanner or
screwdriver remove the
priming screw from the top
of the pump housing by
turning the screw counter
clockwise.
3. Using a hose,  ll the pump
completely with water.
Ensure the pump and
inlet pipe or hose are full.
Replace the priming screw.
1 Ensure the pump’s on/off switch is in the off (0) position and off at
the mains power. 1 Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from
bad weather conditions.
2 .Before storing the pump. It is recommended to drain the pump.
Turn the drain plug anti-clockwise and remove from the pump.
This will drain any excess water. Replace the drain plug by turning
clockwise
1. Induction Motor
2. Electrical Box
3 Adjustable Foot
4 Carry Handle
5 Pumping Housing
6 Discharge Outlet
7 Priming Screw
8 Drain Plug
9 Suction Inlet
TRANSFER PUMP
KNOW YOUR PRODUCT
TRP-650
1. SUCTION INLET 2. DISCHARGE OUTLET 3. PRIMING THE PUMP 4. OPERATING THE PUMP 5. MAINTENANCE & STORAGE
Preparing the Pump: Your pump requires no assembly before
use other than the connection of a suitable inlet/outlet hose and
hose connections (not included).
3. Securely attach the output
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water.
discharge application.
2. Remove the plastic protection
cover from the discharge outlet
and insert a 1” male threaded
hose adaptor (not included)..
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
NOTE: The input hose or pipe you are using must
have a minimum diameter of 25.4mm (1’’).
NOTE: Ensure the input hose or pipe is not
restricted in any way.
NOTE: The discharge hose or pipe you are using
must have a minimum diameter of 19mm (3/4’’).
NOTE: Ensure the discharge hose or pipe is not
restricted in any way and no pressure is obstructing
the hose or pipe when the pump is in operation.
SETUP & PREPARATION OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
NOTE: Whenthepumpisfullyprimedandairisushed
out , the pump is ready to operate. The pump may take
several minutes to fully prime air from inside the pump
and inlet pipe or hose.
The pump is recommended for use with a residual current
device with a rated residual current of 30mA or less.
Make sure the pump is disconnected from electric power
supply before performing maintenance procedures.
2. Remove the plastic protection
cover from the suction inlet
and insert a 1” male threaded
hose adaptor (not included).
Tighten  rmly with a spanner (not
included).
3. Securely attach the input hose
or pipe to the other end of the
adaptor. Ensure you have the
correct diameter hose or pipe
that is compatible with your water
drawing source.
Connecting Hose or Pipe to the
Suction Inlet
1. Te on tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind Te on clockwise on
 ttings
1. Te on tape (not included) is
required on threads to ensure
a water tight seal and prevent
any leakage. Wind Te on
clockwise on  ttings
Ensure the pump is disconnected from the power supply
before performing any of the following operations.
Remove drain
plug & allow
water to drain
out
Slowly  ll
with water
Connecting Hose or Pipe to the Discharge Outlet
NOTE: Ensure the gate valve on your water tank is not left open as
this will allow water to drain from the water tank.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Turn the pump on at the
mains power.
2. Depress the ON/OFF
switch to the ON ( l ) position
3. To turn the pump off, depress the ON/OFF switch to the OFF (0)
position.
2. Using a spanner or
screwdriver remove the
priming screw from the top
of the pump housing by
turning the screw counter
clockwise.
3. Using a hose,  ll the pump
completely with water.
Ensure the pump and
inlet pipe or hose are full.
Replace the priming screw.
1 Ensure the pump’s on/off switch is in the off (0) position and off at
the mains power. 1 Use a moist cloth to wipe down the pump housing. Allow to dry
thoroughly before storing in a dry location that is protected from
bad weather conditions.
2 .Before storing the pump. It is recommended to drain the pump.
Turn the drain plug anti-clockwise and remove from the pump.
This will drain any excess water. Replace the drain plug by turning
clockwise
1. Induction Motor
2. Electrical Box
3 Adjustable Foot
4 Carry Handle
5 Pumping Housing
6 Discharge Outlet
7 Priming Screw
8 Drain Plug
9 Suction Inlet
TRANSFER PUMP
KNOW YOUR PRODUCT
TRP-650
1. SUCTION INLET 2. DISCHARGE OUTLET 3. PRIMING THE PUMP 4. OPERATING THE PUMP 5. MAINTENANCE & STORAGE
Preparing the Pump: Your pump requires no assembly before
use other than the connection of a suitable inlet/outlet hose and
hose connections (not included).
3. Securely attach the output
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water.
discharge application.
2. Remove the plastic protection
cover from the discharge outlet
and insert a 1” male threaded
hose adaptor (not included)..
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
NOTE: The input hose or pipe you are using must
have a minimum diameter of 25.4mm (1’’).
NOTE: Ensure the input hose or pipe is not
restricted in any way.
NOTE: The discharge hose or pipe you are using
must have a minimum diameter of 19mm (3/4’’).
NOTE: Ensure the discharge hose or pipe is not
restricted in any way and no pressure is obstructing
the hose or pipe when the pump is in operation.
SETUP & PREPARATION OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
NOTE: Whenthepumpisfullyprimedandairisushed
out , the pump is ready to operate. The pump may take
several minutes to fully prime air from inside the pump
and inlet pipe or hose.
The pump is recommended for use with a residual current
device with a rated residual current of 30mA or less.
Make sure the pump is disconnected from electric power
supply before performing maintenance procedures.
2. Remove the plastic protection
cover from the suction inlet
and insert a 1” male threaded
hose adaptor (not included).
Tighten  rmly with a spanner (not
included).
3. Securely attach the input hose
or pipe to the other end of the
adaptor. Ensure you have the
correct diameter hose or pipe
that is compatible with your water
drawing source.
Connecting Hose or Pipe to the
Suction Inlet
1. Te on tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind Te on clockwise on
 ttings
1. Te on tape (not included) is
required on threads to ensure
a water tight seal and prevent
any leakage. Wind Te on
clockwise on  ttings
Ensure the pump is disconnected from the power supply
before performing any of the following operations.
Remove drain
plug & allow
water to drain
out
Slowly  ll
with water
Connecting Hose or Pipe to the Discharge Outlet
NOTE: Ensure the gate valve on your water tank is not left open as
this will allow water to drain from the water tank.

TRANSFER
WATER PUMP
600W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 600W
Max. Flow Rate: 3,600l/h
Max. Lift 8m
Max. Head: 40m
Outlet & Inlet: 25mm (1”)Female
Max. Delivery Pressure: 4.0 bar
Water Temp.: 1°C - 35°C
Hmin=: 2m
Weight: 10kg
TRP-650
WHAT’S IN THE BOX
Transfer Water Pump
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: O-rings, bearing, seals gaskets.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
INSTALLATION
TROUBLESHOOTING
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1113
WARNING! The input hose or pipe should be low enough in the water to ensure that if the
water level falls, the pump will not run dry. Ensure that this is checked when in operation.
NOTE: A leaking hose or pipe will draw in air and therefore not draw in any water.
Positioning the Hose or Pipe
Position the input hose or pipe so that it rises from the water drawing source to the pump. Avoid
positioning the input hose or pipe higher than the pump, as this would delay the escape of air
bubbles from the input hose or pipe and impede the priming process (see section ‘starting the
pump’ for description on priming the pump)
Problem Possible Cause Solution
The pump does not start,
or pump water
Pump is not connected to the power supply
Pump is blocked
Pump is not connected to the water supply
Check that the pump is connected to the mains power supply
Disconnect the pump from the mains power. Inspect the discharge outlet and lter
Ensure the pump is connected to the water supply
The pump does not supply water
when the motor is running
The pump has not been primed
Suction line is leaking
The pump is sucking air
Pump is blocked
Pump is not producing enough pressure
Water source does not have enough water
The suction height is too high
The hose diameter is too small
Fill the pump with water, ensure the suction line and pump are lled with water
Check the suction line for leaks and replace hose or pipe if it is damaged or worn
Ensure all connections and ttings are secured tightly
Disconnect the mains power and check the discharge outlet and lter for any foreign matter
Check all parts of the pump and clean
Wait until the water source increases so the pump can operate
Ensure the suction height is no higher than 8m
Ensure the hose diameter is at least 25mm (suction line) and 19mm (discharge line)
Tube or piping does not stay on
the male thread when water is
travelling through
The hose or tubing may be worn or vary
slightly with the dimensions
Add a hose clamp to prevent leaks and secure the hose or pipe
The pump operates intermittently
There is a water leak in the household
plumbing
The voltage is out of range
Air ow is not allowing the motor to cool
The motor is faulty or damaged l
Inspect and x any leaks
Supply the pump in accordance with the rating label requirements
(230-240V)
Ensure the pump is in a well ventilated area
Contact Ozito customer service
Poor Performance
low pressure ow
Faulty suction line Check all the suction lines for leaks or any damage. Replace if they are faulty and check that
you are using a reinforced hose to prevent the hose from collapsing
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landll and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486 New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
ADDITIONAL SAFETY INSTRUCTIONS FOR PUMPS
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save these instructions
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepumpsinexplosiveatmospheres,suchasinthepresenceofammableliquids,
gases or dust. Pumps create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a pump. Distractions can cause you to lose control.\
2. Electrical safety
a. Pump plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) pumps. Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the pump. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
d. When operating a pump, use an extension cord suitable for wet conditions. Use of a cord suitable for
wet use reduces the risk of electric shock.
e. If operating a pump, use a residual current device (RCD) protected supply. Use of an RCD reduces the
risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a pump. Do not use
apumpwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A moment of
inattention while operating a pump may result in serious personal injury.
b. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying pump
with your nger on the switch or plugging in pumps that have the switch on invites accidents.
c. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
d. When operating a pump outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4. Pump use and care
a. Disconnect the plug from the power source before making any adjustments, changing accessories,or
storing pumps. Such preventive safety measures reduce the risk of starting the pump accidentally.
b. Maintain pumps. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the pumps operation. If damaged, have the pump repaired before use. Many
accidents are caused by poorly maintained pumps.
c. Use the pump, and accessories etc., in accordance with these instructions and in the manner
intended for the particular type of pump, taking into account the working conditions and the work to
be performed. Use of the pump for operations different from intended could result in a hazardous situation.
5. Service
a. Haveyourpumpservicedbyaqualiedrepairpersonusingonlyidenticalreplacementparts.This will
ensure that the safety of the pump is maintained.
b. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
GENERAL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING! This product is intended for pumping water in a Home Domestic application.
Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than water
willdamagethewaterpumpand/orcreatearehazard.Failuretofollowallinstructionslisted
belowmayresultinelectricshock,reand/orseriousinjury.
WARNING! This product is not suitable for use with drinking (potable) water.
This appliance is not intended for use by person (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Ensurethewaterpumpisdisconnectedfrommainspowerwheninstalling.
• Donotinstalloroperatethewaterpumpinanexplosiveenvironmentornearammablematerial.
• Donotoperatethewaterpumpwithoutliquid.
• Donotrunthewaterpumpdry.
WARNING! The water pump together with associated pipework operate under pressure. Do not
disconnect water pump or pipework until internal pressure has been released. Failure to do this
could result in personal injury and damage to property.
• Avoid inserting hands into the inlets/outlets of the water pump while it is connected to power.
• Before using the water pump, always inspect it visually. Do not use the pump if it is cracked and/or damaged.
If the water pump is damaged, contact Ozito customer service.
• The water pump has a built-in thermal protection overload switch. The water pump stops if an overload
occurs. The motor restarts automatically after it has cooled down.
• The pump must not be used when people are in the water.
• Never work or perform maintenance on the pump without rst making sure it has been disconnected from the
mains power.
• Pollution of the liquid could occur due to leakage of lubricants Important:
Avoid inserting hands into the mouth of the pump if it is connected to the mains.
The electrical connection must always be made in a dry area. Make sure that electrical connections are protected
from inundations.
Protect the plug and the power cable from heat, oil or sharp edges.
If damaged, The power cable must be replaced by a qualied electrician.
WARNING! When using mains-powered tools, basic safety precautions, including the
following,shouldalwaysbefollowedtoreduceriskofre,electricshock,personalinjuryand
material damage.
Read and understand the manual prior to operating this pump.
Save these instructions and other documents supplied with this pump for future reference. The electric motor has
been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the
rating plate.
Note: The supply of 230V and 240V on Ozito pumps are interchangeable for Australia and New Zealand. This
pump is earthed in accordance with AS/NZS 60335-2-41.
Note: The power outlet used for the water pump is recommended to be protected by a 30mA residual current
device or earth leakage circuit breaker. If the power outlet is external, ensure that it is weather proof. If the supply
cord is damaged, it must be replaced by an electrician or a power tool repairer to avoid a hazard. The water pump
has a built-in thermal protection overload switch. The water pump stops if an overload occurs. The motor restarts
automatically after it has cooled down.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this product. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. Then
using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for
the power input of this product or which is damaged or defective may result in a risk of re and electric shock.
V Volts Hz Hertz
~ Alternating current WWatts
/min Revolutions or noNo load speed
reciprocation per minute
l Litres ºC Degrees celsius
p/hr Per hour kPa Pressure rating (kilopascals)
bar Pressure rating FInsulation class
PVCPolyvinyl chloride IPX8 Ingress protection from water
Regulator compliance mark Warning
Read instruction manual
150mm
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
SUCTION LINE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE BELOW WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE
SUCTIONLINE
WATERTANK
GATE
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
UNION
COUPLING
depending
on installation
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
150mm
mm051
SUCTIONLINE
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE

TRANSFER
WATER PUMP
600W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 600W
Max. Flow Rate: 3,600l/h
Max. Lift 8m
Max. Head: 40m
Outlet & Inlet: 25mm (1”)Female
Max. Delivery Pressure: 4.0 bar
Water Temp.: 1°C - 35°C
Hmin=: 2m
Weight: 10kg
TRP-650
WHAT’S IN THE BOX
Transfer Water Pump
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: O-rings, bearing, seals gaskets.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
INSTALLATION
TROUBLESHOOTING
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1113
WARNING! The input hose or pipe should be low enough in the water to ensure that if the
water level falls, the pump will not run dry. Ensure that this is checked when in operation.
NOTE: A leaking hose or pipe will draw in air and therefore not draw in any water.
Positioning the Hose or Pipe
Position the input hose or pipe so that it rises from the water drawing source to the pump. Avoid
positioning the input hose or pipe higher than the pump, as this would delay the escape of air
bubbles from the input hose or pipe and impede the priming process (see section ‘starting the
pump’ for description on priming the pump)
Problem Possible Cause Solution
The pump does not start,
or pump water
Pump is not connected to the power supply
Pump is blocked
Pump is not connected to the water supply
Check that the pump is connected to the mains power supply
Disconnect the pump from the mains power. Inspect the discharge outlet and lter
Ensure the pump is connected to the water supply
The pump does not supply water
when the motor is running
The pump has not been primed
Suction line is leaking
The pump is sucking air
Pump is blocked
Pump is not producing enough pressure
Water source does not have enough water
The suction height is too high
The hose diameter is too small
Fill the pump with water, ensure the suction line and pump are lled with water
Check the suction line for leaks and replace hose or pipe if it is damaged or worn
Ensure all connections and ttings are secured tightly
Disconnect the mains power and check the discharge outlet and lter for any foreign matter
Check all parts of the pump and clean
Wait until the water source increases so the pump can operate
Ensure the suction height is no higher than 8m
Ensure the hose diameter is at least 25mm (suction line) and 19mm (discharge line)
Tube or piping does not stay on
the male thread when water is
travelling through
The hose or tubing may be worn or vary
slightly with the dimensions
Add a hose clamp to prevent leaks and secure the hose or pipe
The pump operates intermittently
There is a water leak in the household
plumbing
The voltage is out of range
Air ow is not allowing the motor to cool
The motor is faulty or damaged l
Inspect and x any leaks
Supply the pump in accordance with the rating label requirements
(230-240V)
Ensure the pump is in a well ventilated area
Contact Ozito customer service
Poor Performance
low pressure ow
Faulty suction line Check all the suction lines for leaks or any damage. Replace if they are faulty and check that
you are using a reinforced hose to prevent the hose from collapsing
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landll and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486 New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
ADDITIONAL SAFETY INSTRUCTIONS FOR PUMPS
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save these instructions
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepumpsinexplosiveatmospheres,suchasinthepresenceofammableliquids,
gases or dust. Pumps create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a pump. Distractions can cause you to lose control.\
2. Electrical safety
a. Pump plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) pumps. Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the pump. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
d. When operating a pump, use an extension cord suitable for wet conditions. Use of a cord suitable for
wet use reduces the risk of electric shock.
e. If operating a pump, use a residual current device (RCD) protected supply. Use of an RCD reduces the
risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a pump. Do not use
apumpwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A moment of
inattention while operating a pump may result in serious personal injury.
b. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying pump
with your nger on the switch or plugging in pumps that have the switch on invites accidents.
c. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
d. When operating a pump outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4. Pump use and care
a. Disconnect the plug from the power source before making any adjustments, changing accessories,or
storing pumps. Such preventive safety measures reduce the risk of starting the pump accidentally.
b. Maintain pumps. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the pumps operation. If damaged, have the pump repaired before use. Many
accidents are caused by poorly maintained pumps.
c. Use the pump, and accessories etc., in accordance with these instructions and in the manner
intended for the particular type of pump, taking into account the working conditions and the work to
be performed. Use of the pump for operations different from intended could result in a hazardous situation.
5. Service
a. Haveyourpumpservicedbyaqualiedrepairpersonusingonlyidenticalreplacementparts.This will
ensure that the safety of the pump is maintained.
b. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
GENERAL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING! This product is intended for pumping water in a Home Domestic application.
Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than water
willdamagethewaterpumpand/orcreatearehazard.Failuretofollowallinstructionslisted
belowmayresultinelectricshock,reand/orseriousinjury.
WARNING! This product is not suitable for use with drinking (potable) water.
This appliance is not intended for use by person (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Ensurethewaterpumpisdisconnectedfrommainspowerwheninstalling.
• Donotinstalloroperatethewaterpumpinanexplosiveenvironmentornearammablematerial.
• Donotoperatethewaterpumpwithoutliquid.
• Donotrunthewaterpumpdry.
WARNING! The water pump together with associated pipework operate under pressure. Do not
disconnect water pump or pipework until internal pressure has been released. Failure to do this
could result in personal injury and damage to property.
• Avoid inserting hands into the inlets/outlets of the water pump while it is connected to power.
• Before using the water pump, always inspect it visually. Do not use the pump if it is cracked and/or damaged.
If the water pump is damaged, contact Ozito customer service.
• The water pump has a built-in thermal protection overload switch. The water pump stops if an overload
occurs. The motor restarts automatically after it has cooled down.
• The pump must not be used when people are in the water.
• Never work or perform maintenance on the pump without rst making sure it has been disconnected from the
mains power.
• Pollution of the liquid could occur due to leakage of lubricants Important:
Avoid inserting hands into the mouth of the pump if it is connected to the mains.
The electrical connection must always be made in a dry area. Make sure that electrical connections are protected
from inundations.
Protect the plug and the power cable from heat, oil or sharp edges.
If damaged, The power cable must be replaced by a qualied electrician.
WARNING! When using mains-powered tools, basic safety precautions, including the
following,shouldalwaysbefollowedtoreduceriskofre,electricshock,personalinjuryand
material damage.
Read and understand the manual prior to operating this pump.
Save these instructions and other documents supplied with this pump for future reference. The electric motor has
been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the
rating plate.
Note: The supply of 230V and 240V on Ozito pumps are interchangeable for Australia and New Zealand. This
pump is earthed in accordance with AS/NZS 60335-2-41.
Note: The power outlet used for the water pump is recommended to be protected by a 30mA residual current
device or earth leakage circuit breaker. If the power outlet is external, ensure that it is weather proof. If the supply
cord is damaged, it must be replaced by an electrician or a power tool repairer to avoid a hazard. The water pump
has a built-in thermal protection overload switch. The water pump stops if an overload occurs. The motor restarts
automatically after it has cooled down.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this product. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. Then
using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for
the power input of this product or which is damaged or defective may result in a risk of re and electric shock.
V Volts Hz Hertz
~ Alternating current WWatts
/min Revolutions or noNo load speed
reciprocation per minute
l Litres ºC Degrees celsius
p/hr Per hour kPa Pressure rating (kilopascals)
bar Pressure rating FInsulation class
PVCPolyvinyl chloride IPX8 Ingress protection from water
Regulator compliance mark Warning
Read instruction manual
150mm
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
SUCTION LINE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE BELOW WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE
SUCTIONLINE
WATERTANK
GATE
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
UNION
COUPLING
depending
on installation
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
150mm
mm051
SUCTIONLINE
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE

TRANSFER
WATER PUMP
600W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 600W
Max. Flow Rate: 3,600l/h
Max. Lift 8m
Max. Head: 40m
Outlet & Inlet: 25mm (1”)Female
Max. Delivery Pressure: 4.0 bar
Water Temp.: 1°C - 35°C
Hmin=: 2m
Weight: 10kg
TRP-650
WHAT’S IN THE BOX
Transfer Water Pump
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: O-rings, bearing, seals gaskets.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
INSTALLATION
TROUBLESHOOTING
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1113
WARNING! The input hose or pipe should be low enough in the water to ensure that if the
water level falls, the pump will not run dry. Ensure that this is checked when in operation.
NOTE: A leaking hose or pipe will draw in air and therefore not draw in any water.
Positioning the Hose or Pipe
Position the input hose or pipe so that it rises from the water drawing source to the pump. Avoid
positioning the input hose or pipe higher than the pump, as this would delay the escape of air
bubbles from the input hose or pipe and impede the priming process (see section ‘starting the
pump’ for description on priming the pump)
Problem Possible Cause Solution
The pump does not start,
or pump water
Pump is not connected to the power supply
Pump is blocked
Pump is not connected to the water supply
Check that the pump is connected to the mains power supply
Disconnect the pump from the mains power. Inspect the discharge outlet and lter
Ensure the pump is connected to the water supply
The pump does not supply water
when the motor is running
The pump has not been primed
Suction line is leaking
The pump is sucking air
Pump is blocked
Pump is not producing enough pressure
Water source does not have enough water
The suction height is too high
The hose diameter is too small
Fill the pump with water, ensure the suction line and pump are lled with water
Check the suction line for leaks and replace hose or pipe if it is damaged or worn
Ensure all connections and ttings are secured tightly
Disconnect the mains power and check the discharge outlet and lter for any foreign matter
Check all parts of the pump and clean
Wait until the water source increases so the pump can operate
Ensure the suction height is no higher than 8m
Ensure the hose diameter is at least 25mm (suction line) and 19mm (discharge line)
Tube or piping does not stay on
the male thread when water is
travelling through
The hose or tubing may be worn or vary
slightly with the dimensions
Add a hose clamp to prevent leaks and secure the hose or pipe
The pump operates intermittently
There is a water leak in the household
plumbing
The voltage is out of range
Air ow is not allowing the motor to cool
The motor is faulty or damaged l
Inspect and x any leaks
Supply the pump in accordance with the rating label requirements
(230-240V)
Ensure the pump is in a well ventilated area
Contact Ozito customer service
Poor Performance
low pressure ow
Faulty suction line Check all the suction lines for leaks or any damage. Replace if they are faulty and check that
you are using a reinforced hose to prevent the hose from collapsing
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recycling packaging reduces the need for landll and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486 New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
ADDITIONAL SAFETY INSTRUCTIONS FOR PUMPS
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save these instructions
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepumpsinexplosiveatmospheres,suchasinthepresenceofammableliquids,
gases or dust. Pumps create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a pump. Distractions can cause you to lose control.\
2. Electrical safety
a. Pump plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) pumps. Unmodied plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the pump. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
d. When operating a pump, use an extension cord suitable for wet conditions. Use of a cord suitable for
wet use reduces the risk of electric shock.
e. If operating a pump, use a residual current device (RCD) protected supply. Use of an RCD reduces the
risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a pump. Do not use
apumpwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A moment of
inattention while operating a pump may result in serious personal injury.
b. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying pump
with your nger on the switch or plugging in pumps that have the switch on invites accidents.
c. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
d. When operating a pump outdoors, use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4. Pump use and care
a. Disconnect the plug from the power source before making any adjustments, changing accessories,or
storing pumps. Such preventive safety measures reduce the risk of starting the pump accidentally.
b. Maintain pumps. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the pumps operation. If damaged, have the pump repaired before use. Many
accidents are caused by poorly maintained pumps.
c. Use the pump, and accessories etc., in accordance with these instructions and in the manner
intended for the particular type of pump, taking into account the working conditions and the work to
be performed. Use of the pump for operations different from intended could result in a hazardous situation.
5. Service
a. Haveyourpumpservicedbyaqualiedrepairpersonusingonlyidenticalreplacementparts.This will
ensure that the safety of the pump is maintained.
b. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
GENERAL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING! This product is intended for pumping water in a Home Domestic application.
Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than water
willdamagethewaterpumpand/orcreatearehazard.Failuretofollowallinstructionslisted
belowmayresultinelectricshock,reand/orseriousinjury.
WARNING! This product is not suitable for use with drinking (potable) water.
This appliance is not intended for use by person (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Ensurethewaterpumpisdisconnectedfrommainspowerwheninstalling.
• Donotinstalloroperatethewaterpumpinanexplosiveenvironmentornearammablematerial.
• Donotoperatethewaterpumpwithoutliquid.
• Donotrunthewaterpumpdry.
WARNING! The water pump together with associated pipework operate under pressure. Do not
disconnect water pump or pipework until internal pressure has been released. Failure to do this
could result in personal injury and damage to property.
• Avoid inserting hands into the inlets/outlets of the water pump while it is connected to power.
• Before using the water pump, always inspect it visually. Do not use the pump if it is cracked and/or damaged.
If the water pump is damaged, contact Ozito customer service.
• The water pump has a built-in thermal protection overload switch. The water pump stops if an overload
occurs. The motor restarts automatically after it has cooled down.
• The pump must not be used when people are in the water.
• Never work or perform maintenance on the pump without rst making sure it has been disconnected from the
mains power.
• Pollution of the liquid could occur due to leakage of lubricants Important:
Avoid inserting hands into the mouth of the pump if it is connected to the mains.
The electrical connection must always be made in a dry area. Make sure that electrical connections are protected
from inundations.
Protect the plug and the power cable from heat, oil or sharp edges.
If damaged, The power cable must be replaced by a qualied electrician.
WARNING! When using mains-powered tools, basic safety precautions, including the
following,shouldalwaysbefollowedtoreduceriskofre,electricshock,personalinjuryand
material damage.
Read and understand the manual prior to operating this pump.
Save these instructions and other documents supplied with this pump for future reference. The electric motor has
been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the
rating plate.
Note: The supply of 230V and 240V on Ozito pumps are interchangeable for Australia and New Zealand. This
pump is earthed in accordance with AS/NZS 60335-2-41.
Note: The power outlet used for the water pump is recommended to be protected by a 30mA residual current
device or earth leakage circuit breaker. If the power outlet is external, ensure that it is weather proof. If the supply
cord is damaged, it must be replaced by an electrician or a power tool repairer to avoid a hazard. The water pump
has a built-in thermal protection overload switch. The water pump stops if an overload occurs. The motor restarts
automatically after it has cooled down.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this product. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. Then
using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for
the power input of this product or which is damaged or defective may result in a risk of re and electric shock.
V Volts Hz Hertz
~ Alternating current WWatts
/min Revolutions or noNo load speed
reciprocation per minute
l Litres ºC Degrees celsius
p/hr Per hour kPa Pressure rating (kilopascals)
bar Pressure rating FInsulation class
PVCPolyvinyl chloride IPX8 Ingress protection from water
Regulator compliance mark Warning
Read instruction manual
150mm
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
SUCTION LINE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE BELOW WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE
SUCTIONLINE
WATERTANK
GATE
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
UNION
COUPLING
depending
on installation
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
150mm
mm051
SUCTIONLINE
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
RECOMMENDED SET-UP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
FIRM BASE