Ozito PPW-801 User manual

0
1
2
3
4
5
6
Bar
POTABLE
PRESSURE
PUMP
800W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 800W
Max. Flow Rate: 3,200 l/h
Max. Lift: 8m
Max. Head: 38m
Inlet & Outlet: 25.4mm (1”BSP) Female
Max. Delivery Pressure: 3.8 bar
Water Temp.: 1C to 35ºC
IP Rating: IPX4
Weight: 8.4kg
PPW-801
WHAT’S IN THE BOX
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: O-rings, bearing,
seals gaskets.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
thanthatspeciedonthetool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/NewZealand(HeadOfce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
Thebenetsprovidedunderthiswarrantyareinaddition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
0716
0
1
2
3
4
5
6
Bar
Potable Pressure Pump

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
0
1
2
3
4
5
6
Bar
This constant pressure pump is designed for pumping clean water in
the house and garden. It is ideal for providing domestic water supply to
laundries, toilets and outdoor taps, combined with a trigger nozzle and
hose for garden watering and washing cars. Tested to AS/NZS 4020
as suitable for use in contact with drinking water.
Your pump requires no assembly before use other than the connection
of suitable inlet/outlet hose or pipe adaptors (not included).
Positioning the pump
The device must be placed on a
horizontal, level surface that is
sufciently capable of supporting
the total weight of the device
when lled with water.
Four mounting recesses
allow for xing the base to the
mounting surface (bolts not
supplied).
Note: The installation site must be well ventilated and protected from
the effects of weather.
Note: When operating indoors you must ensure that there is a drain in
the oor or a mechanism to prevent leakage.
1. Suction inlet
2. Pressure gauge
3. Priming plug
4. Discharge outlet
5. Carry handle
6. On button
7. Indicator lights
8. Water drain plug
9. Mounting recesses
10. Base
POTABLE PRESSURE PUMP
KNOW YOUR PRODUCT
1. SETTING UP
SETUP & PREPARATION
WARNING!: ENSURE THE PUMP IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE PERFORMING
ANY OF THE FOLLOWING OPERATIONS.
1
8 9 10
4 5 6 732

Connecting to
the discharge outlet
1. Teon tape (not included) is required on
threads to ensure a water tight seal and
prevent any leakage. Wind Teon clockwise
on ttings
2. Remove the plastic protection cover
from the discharge outlet.
3. Insert a 1” male threaded hose
adaptor (not included).
4. Securely attach the output hose
or pipe (not included) to the
other end of the adaptor. Ensure
you have the correct diameter
hose or pipe that is compatible
with your water discharge
application.
Note: The discharge hose or pipe you are using must have a minimum
diameter of 19mm (3/4’’).
Note: Ensure the discharge hose or pipe is not restricted in any
way and nothing is obstructing the hose or pipe when the pump is in
operation.
Connecting to the suction inlet
1. Teon tape (not included) is required
on threads to ensure a water tight seal
and prevent any leakage. Wind Teon
clockwise on ttings.
2. Remove the plastic protection cover
from the suction inlet.
3. Insert a 1”
male threaded
hose adaptor
(not included).
Tighten rmly
with a spanner
(not included).
4. Securely attach
the input hose
(not included)
or pipe to the
other end of the
adaptor. Ensure
you have the
correct diameter
hose or pipe that
is compatible
with your water
drawing source.
Note: The suction pipe should have an internal diameter of at least
25.4mm (1”); it must be kink resistant and suitable for pump use.
Ensure the input hose or pipe is not restricted in any way.
2. SUCTION INLET 3. DISCHARGE OUTLET
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
WARNING!: RISK OF INJURY! IF THE COMPONENTS
ARE NOT COMPRESSION-PROOF OR IF THEY ARE
IMPROPERLY INSTALLED, THE PRESSURE LINE COULD
BURST DURING OPERATION.

Priming the pump is required to purge air from the hose. Don’t operate
the pump without it being primed.
1. Ensure the pump is switched
off at the mains power.
2. Remove the priming plug from
the top of the pump housing
by turning the screw anti
clockwise.
3. Fill the pump completely with
water. Ensure the pump and
inlet pipe or hose are full.
Replace the priming plug.
4. Fully open any (shut-off
mechanisms, spray nozzles,
valves, etc. in the pressure
line) so that the air can escape
without obstruction.
5. Switch the device on at the
mains plug. Press the “On”
button.
Note: When the pump is fully primed and air is ushed out of the suction
cycle, the pump is ready to operate. The pump may take several minutes
to fully prime air from the suction line and inside the pump.
6. When water runs out evenly, close any shut-off mechanisms, spray
nozzles etc. in the pressure line. The pump will now pressurize and
be ready for use.
5. STARTING4. PRIMING THE PUMP
OPERATION
0
1
2
3
4
5
6
Bar
0
1
2
3
4
5
6
Bar
WARNING!: THIS PRODUCT IS INTENDED FOR
PUMPING WATER IN A HOME DOMESTIC APPLICATION.
DO NOT USE IT FOR CORROSIVE, ABRASIVE, EXPLOSIVE
OR DANGEROUS LIQUIDS.
CAUTION. THE PUMP SHOULD BE FILLED WITH WATER
AFTER EACH NEW CONNECTION OR IF WATER LOSS OR
AIR INTAKE HAS OCCURRED. EXTENDED OPERATION
WITHOUT A WATER REFILL WILL DAMAGE THE PUMP!
CAUTION. THE PUMP MUST NOT BE ALLOWED TO RUN DRY.
SUFFICIENT WATER MUST BE ON HAND AT ALL TIMES.
WARNING!: DANGER DUE TO ELECTRIC SHOCK! DO
NOT OPERATE THE DEVICE IN WET SURROUNDINGS!
WARNING!: THIS PUMP MUST BE USED WITH
A RESIDUAL CURRENT DEVICE WITH RATED
RESIDUAL CURRENT OF 30MA OR LESS.
Note: When the pump is fully primed and the air has been ushed out,
the pump is ready to operate.
Starting the pump
The pump and suction line must
be connected and lled.
1. Plug in at the mains power.
2. Press the “On” button.
3. Fully open any shut-off mechanisms (spray nozzles, valves, etc.) in
the pressure line so that the air can escape without obstruction.
4. Check to make sure that water is coming out.
Note: If the pressure line is closed, (such as shutting off a tap down
stream) the pump will build up pressure, then switch off at the preset
cut off. when the pressure line is openned again, the pump will
automatically restart.
If the motor does not start up or the pump does not build up any
pressure or if similar faults occur, turn the device off and refer to
TROUBLESHOOTING section to nd a remedy .

Pressure gauge
The constant pressure pump
also features an inbuilt pressure
gauge (0-6 bar).
This is useful in helping to
diagnose problems such as
leaks, lost pressure, bad check
valve etc.
Cut off pressure is 3.8 bar and
cut in pressure is ~1.5 bar.
Note: The cut in or cut out pressures are factory set and cannot
be adjusted.
Flow Curve
LED Display
‘YELLOW Power on’ LED solid.
This indicates that there is power to the
pump, but the pump is currently not on.
‘YELLOW Power on’ and
‘GREEN Pump on’ LEDs solid
This indicates that there is power to the
pump and the pump is running.
‘YELLOW Power on’, GREEN Pump on’
and ‘RED Failure’ LEDs solid.
There is power to the pump, the pump
motor is running but ow is stalled. The
pump will continue to run for another 30
seconds to try to restore ow.
‘YELLOW Power on’ and
‘RED Failure’ LEDs solid.
After 30 seconds of no ow, the pump
motor turns off. This status Indicates
that there has been a failure and that
something needs to be changed to correct
the problem. The problem could be that
there is no water ow into the pump
(upstream tap off) or that there
is an air lock that needs to be bled out.
‘YELLOW Power on’ LED ashing
A tap downstream of the pump has been
turned off increasing the water pressure
to the pump’s maximum. The pump motor
switches off and is in a standby mode
until the tap is opened again.
PPW-801
6. OPERATING THE PUMP
0
1
2
3
4
5
6
Bar
3.8 Bar
1.5 Bar