Ozito PXGTPS-0182 User manual

STANDARD EQUIPMENT
PXGTPS-0182
INSTRUCTION MANUAL
SPECIFICATIONS
Input Power: 18V x 2
Flow Rate Max.: 3000 l/h
Suction Height Max.: 8m
Delivery Height Max.: 26m
Delivery Pressure Max.: 2.6 bar
Water Temperature. 1°C - 35°C
Inlet & Outlet: 25mm (1”)
Noise Rating: 76 dB
Weight: 3.3kg
ozito.com.au
0720
Garden Transfer Pump
GARDEN
TRANSFER PUMP
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts, for example: O-rings, bearings, seals, gaskets .

BATTERY & CHARGER
This tool is compatible with all battery and chargers from the Ozito
Power X Change Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1. Battery Cover
2. Carry Handle
3. Pump Setting Switch
4. Discharge Outlet
5. Priming Plug
6. Drain Plug
7. Suction Inlet
CORDLESS GARDEN TRANSFER PUMP
KNOW YOUR PRODUCT
1. INLET & OUTLET
SETUP & PREPARATION
1 2 3 4 5
6 7
WARNING!: ENSURE THE TOOL IS OFF AND THE
BATTERIES ARE REMOVED BEFORE PERFORMING
ANY OF THE FOLLOWING OPERATIONS.
1. Thread seal tape (not included) is
required on threads to ensure a
water tight seal and prevent any
leakage. Wind thread seal tape
clockwise on ttings.
Note: The input hose or pipe you are using must have a minimum diameter
of 25.4mm (1”).
Preparing the Pump: Your pump requires no assembly
before use other than the connection of a suitable inlet/
outlet hose and hose connections (not included).
2. Remove the plastic protection
cover from the suction inlet
and insert a 25.4mm ( 1”)
male threaded hose adaptor
(not included). Tighten rmly
with a spanner (not included).
3. Securely attach the input
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water
drawing source.
WARNING!: ENSURE THE INPUT HOSE OR PIPE
IS NOT RESTRICTED IN ANY WAY.
Connecting Hose or Pipe to the Suction Inlet
Note: A leaking hose or pipe will draw in air and therefore not draw in any
water.

2. INSERTING & REMOVING THE BATTERIES
Connecting Hose or Pipe to the
Discharge Outlet.
1. Thread seal tape (not included) is
required on threads to ensure a water
tight seal and prevent any leakage. Wind
thread seal tape clockwise on ttings.
2. Remove the plastic protection
cover from the discharge
outlet and insert a 25.4mm
(1”) male threaded hose
adaptor (not included).
Tighten rmly with a spanner
(not included).
3. Securely attach the input
hose or pipe to the other
end of the adaptor. Ensure
you have the correct
diameter hose or pipe that is
compatible with your water
discharge application.
WARNING!: ENSURE THE DISCHARGE HOSE
OR PIPE IS NOT RESTRICTED IN ANY WAY AND
NOTHING IS OBSTRUCTING THE HOSE OR PIPE
WHEN THE PUMP IS IN OPERATION.
Note: The discharge hose or pipe you are using must have a minimum
diameter of 13mm (1/2”).
WARNING!: RISK OF INJURY! IF THE
COMPONENTS ARE NOT COMPRESSION-
PROOF OR IF THEY ARE IMPROPERLY INSTALLED,
THE PRESSURE LINE COULD BURST DURING
OPERATION.
Inserting the Batteries
Always use 2 batteries of the same capacity and
charge state with the garden transfer pump.
1. Slide two batteries of the same capacity and same charge state into the
battery mount aligning the ribs so that they click into place.
Note: For best performance use only batteries which are charged to the
same level. Never combine full and half-full batteries as the equipment‘s
operating time depends on the battery with the lower charge level.
Removing the Batteries
1. Press and hold the battery release tab to release a battery and slide the
battery out.
PRESS

PXGTPS-0182
3. PUMP SETTING SWITCH 4. PRIMING AND OPERATING THE PUMP
OPERATION
Priming the pump is required to purge air from the hose
Don’t operate the pump without being primed.
WARNING!: THE PUMP SHOULD BE FILLED
WITH WATER AFTER EACH NEW CONNECTION
OR IF WATER LOSS OR AIR INTAKE HAS
OCCURRED. EXTENDED OPERATION WITHOUT A
WATER REFILL WILL DAMAGE THE PUMP!
On/Off/Pump Switch
Switch position “O”: Off
Switch position “I”: Pump
setting 1, ECO
Switch position “II”: Pump
setting 2, BOOST
- Pump Setting 1
Max. Flow rate: 3000 l/h
Max. Delivery height: 17m
Max. Suction height: 8m
Max. Delivery pressure: 1.7 bar
- Pump Setting 2
Max. Flow rate: 3000 l/h
Max. Delivery height: 26m
Max. Suction height: 8m
Max. Delivery pressure: 2.6 bar
Note: Selecting pump setting 2 increases the maximum delivery pressure,
but it reduces the maximum operating time of the battery as a result.
1. Ensure the pump setting switch is in the off (0) position and the pump is
positioned on a horizontal, level surface.
2. Remove the priming plug
from the top of the pump
housing by turning anti
clockwise.
3. Fill the pump completely
with clean water. Ensure the
pump and suction inlet pipe
or hose are full. Replace the
priming plug.
WARNING!: THIS PRODUCT IS INTENDED
FOR PUMPING WATER IN A HOME DOMESTIC
APPLICATION. DO NOT USE IT FOR CORROSIVE,
ABRASIVE, EXPLOSIVE OR DANGEROUS LIQUIDS.
4. The intake process starts automatically after you have pressed the pump
setting switch.
This garden transfer pump is designed for pumping clean water for irrigation
and watering landscape areas, vegetable beds and gardens. It is ideal for
operating lawn sprinklers.
Note: When the pump is fully primed and air is ushed out , the pump is
ready to operate. The pump may take several minutes to fully prime air from
inside the pump and inlet pipe or hose.
WARNING!: ENSURE THE OUTLET FOR THIS
PUMP, INCLUDING ANY HOSES OR PIPES ARE
NOT RESTRICTED OR OBSTRUCTED IN ANYWAY.
TAPS, VALVES AND ANY TYPE OF TRIGGER NOZZLE
MUST NEVER BE USED WITH THIS PUMP. FAILURE
TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN
PUMP FAILURE OR SERIOUS INJURY
5. Switch the pump off again after use by pressing the pump setting switch.
Note: IPX4 - pump can handle splashing of water with no harmful effect.

DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
SPARE PARTS
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse.
For further information, or any parts not listed here,
visit www.ozito.com.au or contact Ozito Customer
Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
Power tools that are no longer usable should not be disposed of with household waste
but in an environmentally friendly way. Please recycle where facilities exist. Check
with your local council authority for recycling advice.
Recycling packaging reduces the need for landll and raw materials. Reuse of recycled
material decreases pollution in the environment. Please recycle packaging where
facilities exist. Check with your local council authority for recycling advice.
MAINTENANCE
RECOMMENDED SET-UP
SUCTIONLINE
WATERTANK
GATE
VALVE
Connection with tank base above transfer pump
UNION
COUPLING
depending
on installation
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
LEVEL GROUND
150mm
IN-LINE
FILTER
mm051
SUCTIONLINE
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
Connection with tank base level with transfer pump
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
LEVEL GROUND
IN-LINE
FILTER
150mm
WATERTANK
GATE
VALVE
NON-RETURN
VALVE
SUCTION LINE
Connection with tank base below transfer pump
150mm
SOLID STRUCTURE
DISCHARGE
OUTLET
UNION
COUPLING
depending
on installation
LEVEL GROUND
IN-LINE
FILTER
l
Litres per hourL/H
Direct current
Sound power level
76
Note: A non-return valve is recommended so that the water does not run off when the pump
is shut off.
Note: A suction in-line lter with a 3000 l/hour min ow rate, and 150 to 250 micron
mesh must be used to protect the pump from sand, dirt etc. The Ozito PAPF-001 Pre-lter or
equivalent is available from Bunnings stores.
Note: The pump must be placed on a horizontal, level surface that is sufciently capable of
supporting the total weight of the pump when lled with water.
Two mounting recesses allow for xing the base to the mounting surface (bolts not supplied).
WARNING!: THE INPUT HOSE OR PIPE SHOULD BE
LOW ENOUGH IN THE WATER TO ENSURE THAT
IF THE WATER LEVEL FALLS, THE PUMP WILL NOT
RUN DRY. ENSURE THAT THIS IS CHECKED WHEN IN
OPERATION
WARNING!: ENSURE THE BATTERIES ARE
REMOVED TO PREVENT ACCIDENTAL
STARTING BEFORE PERFORMING MAINTENANCE
PROCEDURES.
Use a moist cloth to wipe down the pump housing. Allow to dry thoroughly before storing in a
dry location that is protected from bad weather conditions.
Cleaning
Storage
If there is danger of frost, dismantle the device and accessories, clean and store them in a
place protected from frost.
Dismantle and store
1. Remove batteries.
Note: Ensure the gate valve on your water tank is
not left open as this will allow water to drain from the
tank.
3. Completely empty the pump by unscrewing the drain
plug.
4. Dismantle the suction and pressure lines from the
device.
5. Store device in a frost-free room (at least 5 °C).
Note: Ozito Industries will not be responsible for any
damage or injuries caused by the repair of the transfer
pump by an unauthorised person or by mishandling of the garden transfer pump. This tool is
designed for DIY use - use in commercial or industrial environments will void the warranty.
Note: The installation site must be well ventilated and protected from the effect of weather.
Position the input hose or pipe so that it rises from the water drawing source to the pump.
Where possible, avoid positioning the input hose or pipe higher than the pump, as this would
delay the escape of air bubbles from the input hose or pipe and impede the priming process.

ELECTRICAL SAFETY
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of fire, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The charger has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New
Zealand.
This tools charger is double insulated; therefore no earth wire is required.
Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting
from a possible electrical insulation failure within the tool.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in
order to avoid a hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect
the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged
or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension
lead not suitable for the power input of the tool or which is damaged or defective may result in a
risk of fire and electric shock.
The power supply for this products charger should be protected by a residual current device (rated
at 30mA or less). A residual current device reduces the risk of electric shock.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you
to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related
hazards.
h. Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles. A careless action can cause severe injury within a fraction of a
second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous in
the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling and control of the tool in unexpected
situations.
5. Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not charge the battery pack or tool outside the
temperature range specified in the instructions. Charging improperly or at temperatures outside
the specified range may damage the battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs. Service of battery packs should only be performed by
the manufacturer or authorized service provider.
ADDITIONAL SAFETY WARNINGS FOR PUMPS
WARNING! This product is intended for pumping water in a Home Domestic application. Do
not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than water will
damage the water pump and/or create a fire hazard. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury.
WARNING! This product is not suitable for use with drinking (potable) water.
This appliance is not intended for use by person (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Ensure the water pump is disconnected from mains power when installing.
• Do not install or operate the water pump in an explosive environment or near flammable
material.
• Do not operate the water pump without liquid.
• Do not run the water pump dry.
WARNING! The water pump together with associated pipework operate under pressure. Do
not disconnect water pump or pipework until internal pressure has been released. Failure to
do this could result in personal injury and damage to property.
• Avoid inserting hands into the inlets/outlets of the water pump while it is connected to power.
• Before using the water pump, always inspect it visually. Do not use the pump if it is cracked and/
or damaged. If the water pump is damaged, contact Ozito customer service.
• The transfer pump has a built-in thermal protection overload switch, which prevents the motor
from damage due to overheating. The water pump stops if an overload occurs. The motor
restarts automatically after it has cooled down.
• The pump must not be used when people are in the water.
• Never work or perform maintenance on the pump without first making sure it has been
disconnected from the mains power.
• Pollution of the liquid could occur due to leakage of lubricants Important:
Avoid inserting hands into the mouth of the pump if it is connected to the mains.
The electrical connection must always be made in a dry area. Make sure that electrical
connections are protected from inundations.
Protect the plug and the power cable from heat, oil or sharp edges.
If damaged, The power cable must be replaced by a qualified electrician.
If no water is produced within 5 minutes, stop pump, release all pressure, remove priming plug,
refill and try again.
WARNING! Hazardous pressure and risk of explosion and scalding. If pump is run
continuously at no flow (that is, with discharge shut off or without priming), water may
boil in pump and piping system. Under steam pressure, pipes may rupture, blow off
fitting or blow out pump ports and scald anyone near.
To prevent explosion, do the following:
A. Ensure discharge is open whenever pump is running.
B. If pump fails to produce water when attempting to prime, release all pressure, drain pump and
refill with cold water after every two attempts.
C. When priming, monitor pump and piping temperature. If pump or piping begin to feel warm to
the touch, shut off pump and allow system to cool. Release all pressure in the system and refill
pump and piping with cold water.