P2 MOBILE TECHNOLOGIES LIMITED Z100 Installation guide

P2 Mobile Technologies
Wirelessing the world … with no limitation.
Z100 Product Training
Nov-2015
P2 Mobile Technologies Limited -- Confidential

Table of Content
13/1/16P2 Mobile Technologies Limited -- Confidential
1. Z100 Hardware introduction (Z100 & POE
injector)
2. Basic Configuration Using SmartMoment
(Lightweight)
3. Advanced Configuration Using CLI
4. Status Monitoring using Mesh Provision Server

1 2 3 4 5 6 7
LEDs LAN Port Console
port Reset button DC power connector USB port Kensington Lock Slot
Z100 Hardware

LED Function State - Colour Indication
RUN AP power / ready
status Steady –Green AP is ready
Flashing –Green AP is booting up
Red AP hardware failure
Off No power to AP
LAN Network Link Status Steady –Green 1000Mbps Ethernet link negotiated
Steady –Yellow 10/100Mbps Ethernet link negotiated
Flashing Ethernet link activity
Off Ethernet link unavailable
5G 5GHz Radio Status Steady –Green 5GHz radio is enabled
Off 5GHz radio is disabled
2.4G 2.4GHz Radio
Status Steady –Green 2.4GHz radio is enabled
Off 2.4GHz radio is disabled
Z100 status indicated by LEDs

Ports & Connectors Quantity and Specifications
1 LEDs 4 LED indicate different status of AP
2 DC Jack Range: 12 V DC 1A
3Ethernet Port 1 ×10/100/1000 Mbps Ethernet port
PoE input:802.3af
4Console A RJ-11 port. Connect the AP to a serial
terminal or a laptop for direct local
management.
5Reset Press the button longer than 5s to restore the
AP to default settings.
6USB Up to 0.5A USB connection for future
extension.
7Kensington Lock Slot For added security using Kensington lock.
8Mounting Back Fit with mounting components to install the AP
to various surfaces or locations. The two
mounting types include drop ceiling mount and
wall mount.
Explanation of ports and connectors

Z100 –Wall mounting(1)
1. Drive two screws in
the wall. The distance
between two screws
should be 40mm.
2. Align the bracket
with screws.
3. Pull down the
bracket until it is
fastened tightly.

Z100 –Wall mounting(2)
4. Align the securing
hook of the AP with
the bracket from up to
down until it is locked
securely.

Z100 –Ceiling mounting(1)
1. Secure the ceiling
bracket on the ceiling
rail and adjust
according to the size
of the rail.
2. Fasten the bracket
with the ceiling rail
with a screw.

Z100 –Ceiling mounting(2)
3. Align the securing hook
of the AP with the bracket
(see dotted line), and slide
the AP towards the
bracket until the AP is
completely locked.
4. Use the cable-tie
through the locking hole to
lock the AP with the
bracket.

Gigabit PoE+ Injector
GE.PW-AT00-00
Optional purchase
For Z100/Z500/X20
802.3at/af Compliant
Output: 54V, 0.65A,
35W (Max.)
1000 Mbps Ethernet,
Full Duplex
C8 Appliance Inlet
Excluding power cord
with C7 Connector and
Ethernet port)

2 Mounting
holes
LEDs
•AC: Green
light = power
OK
•PORT:
Green light =
PoE OK
Gigabit PoE+ Injector

Table of Content
13/1/16P2 Mobile Technologies Limited -- Confidential
1. Z100 Hardware introduction (Z100 & POE
injector)
2. Basic Configuration Using SmartMoment
(Lightweight)
3. Advanced Configuration Using CLI
4. Status Monitoring Using Mesh Provision Server

SmartMoment (Lightweight)
SmartMoment (Lightweight Mode) is a built-in
configuration tools and virtual controller designed to
streamline the process of setting-up a P2 AP.
SmartMoment Lightweight mode is for basic
configuration ONLY. You can use CLI for advanced
setting.
Please refer to the SmartMoment User Guide for
more details.

SmartMoment (Lightweight)
Use SmartMoment to quickly set up the vanilla AP
(1) From Wireless
Power up the AP
Connect to SSID “P2Wifi” with password “p2wtuser”
Enter the IP address “172.16.0.1” in browser
Use default Login Username “p2wtadmin” and
Password “p2wtadmin”
(2) From Wired
Power up the AP
Connect the AP and a PC with a LAN cable
Set the IP of the PC to “192.168.1.2/24”
Enter the IP address “192.168.1.1” in browser
Use default Login Username “p2wtadmin” and
Password “p2wtadmin”
Refer to SmartMoment User Guide for detailed configuration

You can configure the AP to:
Router mode
Access-Point mode
Mesh mode
SmartMoment (Lightweight)

SmartMoment (Lightweight)
Router mode
Ability to assign IP to client devices through built-in
DHCP service
Network address translation (NAT) between Ethernet
port and WLAN
Access-Point mode
Add WLAN capability to an existing L2 network
Should connect to a router/hub/switch through an
Ethernet cable
LAN port and WLAN bridged
Mesh mode
Enable AP as an node of a Wireless Mesh Network
Form a Mesh link to replace the wire of a connection

SmartMoment (Lightweight)
Z100 Z500 X20
Router
mode Y Y
Access-Point
mode Y Y
Mesh mode Y
Recommended application

SmartMoment (Lightweight)
Sign In Z100:

SmartMoment(Lightweight)
Overview(1)
–Hardware Manager
•Firmware version
•Model