Discount Car Stereo A2DIY-VOL Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2DIY-VOL
QUICK START BLUETOOTH INSTALLATION GUIDE FOR VOLVO CD CHANGER CONTROLLING RADIOS

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirements:
Radio with cd changer controls
Introduction
Many Volvo car owner’s adamant about keeping their cars as stock possible, will
be thrilled with the A2DIY-VOL kit which adds modern Bluetooth features without
changing the look and feel of dashboard components. Features Bluetooth
Hands-Free and music streaming from any Smartphone with A2DP and HFP
support. In addition to Bluetooth, a hardwired 3.5mm input jack is available for
users to connect and play non-Bluetooth devices such as Mp3 players, satellite
radio kit, iPods etc. A smart remote control for Apple and Android devices allows
users to track up/down, pause, increase/decrease device volume and more.
Optional USB charging port to keep devices charged while on the road.
Keep the radio and car you love while enjoying Bluetooth features only
available on newer cars. For more details, see Frequently Asked question at
the end of this guide.
Installation
Warning: Although not critical, we recommend disconnecting battery.
Keep in mind, most Volvo radios are coded and will not operate without
code. Radio code must be available for radio to operate upon
reconnection
1. Remove radio by pressing both spring-loaded release tabs as seen in
Fig. 1
Fig. 1
2. Place finger inside release ring and pull outward as seen in Fig. 2
Fig. 2

3. Connect harness 8-pin plug (See Fig. 3) to “CD”port (See. Fig. 4).
Factory CD changer (if present) must be disconnected.
Fig. 3
Fig. 4
Radio’s 8-pin changer port
4. AUX input connection: Connect supplied 3.5mm audio cable (See Fig.
5) to module “AUX” jack (See Fig. 6). Route and connect other end to
front of the dash or wherever Aux device will reside (within 3 ft.)
Fig. 5
Fig. 6
5. Optional push-button microphone: Connect microphone plug to
Module “MIC” input jack and secure button in location within driver
reach (cable is 6ft. long). Simply remove tape backing and adhere to
surface.
6. Standard microphone: Secure microphone to visor or headliner using
included visor clip (See Fig. 8).
Fig. 8
Microphone
Fig. 8
Visor clip
7. Carefully route microphones 3.5mm plug down side pillar and behind
the dash and connect to module “MIC” input.
8. Tap adapter harness RED wire to one of two GREEN/BROWN
accessory wires on radio harness (See Fig. 9)

9. Tap YELLOW wire from installation harness to YELLOW/PURPLE
(Battery supply) wire on radio harness or another source for 12V
battery supply (See Fig. 9)
Fig. 9
11. Secure adapter box and proceed to next section.
Optional charging port
Add Optional “Fast charge kit –to charge devices while on the road. Custom
install in a convenient location and discover how this charger is a massive
improvement over many anemic aftermarket cigar lighter chargers.
To add USB charging kit to your order, tap the option on order page,
Should you decide to add the USB Port, we suggest 2 mounting options:
A. Flush to dash/panel requires drilling a ¾” hole in the dash
B. Flush with Support bracket (use this option to mount USB terminal
wherever your installation demands without drilling)
A. Flush to Dash or Panel (requires drilling)
1. Drill a ¾” hole in the dash or panel using a step drill bit or equivalent
(See Fig. 10)
Fig. 10
Step drill bit
2. Insert USB male terminal through the ¾” hole created in step 1 and
connect to module USB port (See Fig. 12)
Fig. 11
USB 6 ft. cable with bracket
Fig. 12
USB charging port

3. Push USB head (See Fig. 13) until it snaps in place and flush with
mounting surface (See Fig. 14)
Fig. 13
USB head
Fig. 14
Flush mounted to dash
4. Tuck and secure any extra wire from moving parts and test operation
(See Enabling the AUX section below)
B. USB with Bracket Mount (No drilling)
1. Locate a flat surface at location of choice within 3.2 ft. of radio and
mount USB support bracket (See Fig. 15) to surface using
adhesive/tape or screws.
Fig. 15
USB mounting bracket
2. Insert the 6 ft. USB male terminal through bracket hole (See Fig. 16)
and connect to Module USB port (See Fig. 12)
Fig. 16
3. Push USB head until it snaps in place and flush (See Fig. 17)
Fig. 17
Tuck and secure any extra wire away from moving parts and test operation ( See
Pairing and Connection

Pairing module
Pairing varies among devices but basic steps are the same. This process is done
upon initial install and will not have to be repeated
1. Turn Ignition and radio “ON”
Blue LED in adapter peephole will flash (pairing mode)
2. On A2DP device: go to Settings, Wireless & Networks, Bluetooth
Settings
3. Select Bluetooth and turn on, select Bluetooth settings
4. Tap Scan for devices .
5. Wait for Bluetooth device name (See below) to appear and select it.
Once paired Blue LED inside peephole flashes once every 2 seconds
and confirmation tone is heard on car speakers
One connection
The A2DIY-VOL connects to one device at a time. You must disconnect/unpair
first device before pairing a second, or simply disable Bluetooth on first device.
Warning! Voice Recognition applications (e.g. Siri, Google Play etc.) must be enabled on
device as you would in portable mode.
Media button
Pairing Bluetooth media button: Ensure Bluetooth is enabled on your
device (e.g., Smartphone/Tablet etc.)
Press and hold pause/play button (See Fig. 18) until Blue LED flashes
Scan smartphone for available devices and select BT009 from list. (Blue LED
turns off).
Fig. 18
Installation:
Attach button to steering wheel (includes holder) or dashboard using included
double sided tape –your choice!

Operation:
Once paired with smartphone/Tablet, users may perform the following functions
on iOS devices with Bluetooth 3.0 and later or Android 4.0 or later.
Media button functions are NOT applicable to the C5 radio.
Charging:
Media button built-in rechargeable 200mAH battery may last up to 10 days. Use
supplied USB cable to charge. Red LED indicates charging; Full charge is reached
after 2 hours at which time LED turns off.
Volvo Bluetooth comparison chart
Feature
A2D-VOL
A2DIY-BKR
CD changer retention
x
x
3.5mm AUX input
x
✓
USB charging port
x
**
Muting
*
*
Hands-Free profile
x
✓
Music streaming
✓
✓
Push-to-talk button
x
✓
Remote control
*
✓
Multi-device pairing
✓
✓
* When radio is in CD changer (Bluetooth Mode)
** Optional

Operation:
1. Turn ignition to ACC and radio “ON”
2. Press radio “CD” CHG” or “CHGR” button to enter AUX mode
3. Launch smartphone music streaming application
4. Use media button to change tracks, adjust device volume, pause etc.
5. Place phone call or ask someone to call.
6. Adjust call volume with media button, steering wheel controls or radio
volume knob.
7. To end call press media button, Pause/Play
8. To listen to AUX device, press media button Pause/Play.
9. If correct operation is confirmed go ahead and reinstall radio.
Warning: Playlist and Track selection is *NOT* possible using Becker
radio button. Use audio device built-in controls and display or media
button to access and control audio files and applications.
Notes: if no auxiliary device is connected, press media button play/stop to
pause streaming media.
Adding additional load to the electrical system in older vehicles can result in
alternator whine or similar noise. For these instances the included noise filter
must be installed. (See Fig. 19).
Fig. 19
Noise filter installation
Install filter between vehicle supply wires and module as follows:
Connect filter (in) red wire to accessory supply wire (car side)
Connect filter (out) red wire to Bluetooth module red wire
Connect filter (in) black wire to radio ground wire (or radio chassis)
Connect filter (out) black wire to Bluetooth module black wire

Frequent ask questions & Troubleshooting
1. What’s the difference between A2D-VOL and A2DIY-VOL?
See Bluetooth comparison chart on previous page.
2. Does the A2DIY-VOL work on all Volvo radios?
NO; works only on Volvo “SC” and select “CT” radios with CD changer
controls. (non-changer controlling radios are not supported)
3. Is there something available for non- “CD changer “controlling radios?
YES; Purchase our ISFM23 or ISFM2351.
4. Can I control Smartphone from radio buttons?
NO; you must use Smartphone built-in controls and display to operate
device, or use included smart remote control. Volume button on radio is
used to set the playback level.
5. Can I pair or save more than one device to the A2DIY-VOL?
YES; more than one device (slaves) can be paired however only one
connection can be active at a time. To pair a second device, you must
disconnect first device.
6. When listening to aux device, audio playback is interrupted with every
press of smartphone button. Is this normal?
YES,when in aux mode, smartphone button operation temporarily
interrupts music playback.
Disclaimer
• This product has no affiliation with Volvo.
• We’re not liable for misuse of this product.
•We recommend professional installation.
Email [email protected]
© 1995-Sep-21 Discount Car Stereo All rights reserved. Information in this document is subject
to change without notice. Other products and companies referred to herein are trademarks or
registered trademarks of their respective companies or mark holders.