PAC LOC PRO ADVANCED LPA-1.2 User manual

12V
Connect to a fused
+12V constant source
GND
Connect to a good
chassis ground
REM IN
Remote turn on input (+)
REM OUT
Remote turn on output (+)
The LPA will provide a
+12V Remote Output using
DC Signal Sense from the
Right channel inputs
SPEAKER SIGNAL INPUTS
Connect to head unit or
amplier speaker outputs
RCA SIGNAL OUTPUTS
Connect to amplier inputs
GROUND ISOLATION
Selectable: GND / ISO / 200Ω
Default: ISO
If ground / engine noise is present,
the jumper can be repositioned.
GAIN
Variable: -27.3dB — +3.2dB
Allows gain adjustment of
the output signal
CLIP
Indicates signal clipping when
gain is set to high
LOAD SELECT
Selectable: 20Ω / 60Ω / 20KΩ
Default: 20KΩ
For factory audio systems requiring a
resistance load to output audio, select
60Ω first, then 20Ω. All others use 20KΩ
setting.
LPA-1.2 | 2 Channel Line-Output Converter
LPA-1.4 | 4 Channel Line-Output Converter
The L.O.C.PRO ADVANCED™ can be used to add ampliers to an audio system that does not have RCA outputs or
when replacing an OEM radio and retaining the factory amplied system. Variable Gain Controls with Clipping Indicators,
Selectable Ground Isolation and Load Select features ensure a pure, noise-free signal for any type of audio system.
This Quick Start Guide will get you going, but if you need additional help or information, please visit our website or
contact Technical Support.
Features & Wiring Information
Quick Start Guide
Technical Support | Phone: [phone] | Email: [email protected] | Chat: PAC-Audio.com | ©2020
X
FULLY OPEN TERMINALS
BEFORE INSERTING WIRE
JUMPERS CAN BE
TRIMMED FLUSH

1 2 3 4 5 6 SET
SEEK SEEK AM/FM DISC AUX RW FF
Speaker level input from a radio to RCA level output for an aftermarket amplier is the most commonly used conguration for the
L.O.C.PRO ADVANCED. This will create RCA level outputs from a radio that only has speaker level outputs.
In the example below, the Positive(+) and Negative(-) wires of two speakers are “tapped” and connected to the SPEAKER SIGNAL
INPUTS of the LPA. The speakers will continue to play as normal. The REM OUT is connected to the ampliers turn-on. When the
radio is turned on the LPA will automatically turn on the amplier. Lastly, the RCA SIGNAL OUTPUTS from the LPA are connected
to the aftermarket ampliers inputs.
Example Installation
Model Number LPA-1.2 LPA-1.4
Channels 2 IN — 2 OUT 2 IN — 4 OUT
Operating Voltage 9V—16V 9V-16V
Max Input Level (20kHΩLoad Setting) 20V / 100W 20V / 100W
Auto Turn On DC Offset / Remote DC Offset / Remote
Output Voltage MAX @ 13.8V 9.5V RMS 9.5V RMS
Turn On Trigger (DC-Offset) 3V—7V 3V—7V
Load Input Impedance 20Ω, 60Ω, 20KΩ 20Ω, 60Ω, 20KΩ
Output Impedance <120Ω <120Ω
Variable Gain Adjustment -28dB—+1dB -28dB—+1dB
Signal To Noise >110dBA @ 6.4V Output >110dBA @ 6.4V Output
THD+N < 0.01% < 0.01%
Input Sensitivity 0.5V—20V 0.5V—20V
Frequency Response 10Hz—20kHz 10Hz—20kHz
Current Draw (Max) 40mA 40mA
Low Pass Filter NO NO
Bass Boost NO NO
Clip Indicator YES YES
Remote Level Control NO NO
Chassis Type Stamped Steel Stamped Steel
Terminal Gauge 18AWG / Screw Type 18AWG / Screw Type
Specications
OEM RADIO
CHASSIS GROUND (-)
12V CONSTANT POWER (+)
REMOTE AMP TURN-ON
Technical Support | Phone: [phone] | Email: [email protected] | Chat: PAC-Audio.com | IM-LPA1X REV. 012121
For more installation examples, tech tips and updates,
visit the L.O.C.PRO ADVANCED product pages on
PAC-Audio.com