Pacific Ears T Series Live! User manual

Care and Maintenance of your ACS In-Ear Monitors
It is important that you read these notes to ensure longevity
of your custom in-ear monitors. Cleaning them regularly
and paying close attention to their maintenance is vital to
ensure their continued performance. We offer full cleaning
and reconditioning services for your monitors so please don’t
hesitate to call if your monitors need attention.
Cleaning and Storage
Use a moist cloth or sterile wipe to clean the silicone
moulds and cables. Do not allow any moisture into
the cable connections when cleaning. Do not immerse
any part of the monitors in any liquid. Do not get your
monitors wet. Please use the enclosed dehumidifier
following each use (instructions enclosed) to ensure that
your monitors remain free from moisture and store them
in the pouch and hard case supplied when not in use.
Visually inspect the sound ports on each earpiece
after use to check that no wax, skin debris or dirt has
penetrated the tubes. Use the wax pick provided to
carefully remove any matter.
NOTE : The most common cause of monitor failure is
ingression of ear wax or sweat into the sound tubes. This
is easily prevented by regular checks, cleaning and use
of the dehumidifier.
If you need to replace your cable
Your cable is serviceable and may be replaced in
the event of failure. Each plug has a coloured dot
that corresponds to the colour coding on your
earpieces. To connect your cable, present the
plug to the cable inlet with the dot oriented to
the flat face of your earpiece (fig 5). Push the plug
into the mould (fig 6), press the plug home into the
socket in the mould (fig 7). If required gently press
onto the plug through the silicone to ensure that it is
properly seated in the connector.
Fitting
Your monitors are handed, the right earpiece being identified with a red detail and
the left earpiece with a blue detail. From a comfort and acoustic perspective, it is
important that they are fitted correctly to provide a good seal of the ear.
Begin by placing the tip of the monitor into your
ear canal (fig 1) whilst at the same time twisting
gently backwards (fig 2). It is sometimes easier to
use both hands when fitting the earpieces making
sure that the top part of the mould is located
under the flap of skin at the top of the ear (fig 3).
Gently press the mould until it feels located and
secure (fig 4). Use the comfort cream to help the
fitting initially and create a good seal if required.
Spread a small amount around the ear canal tip,
being careful to avoid the sound tubes.
We want you to be delighted with your ACS in-ear
monitors. If, for any reason, you experience difficulties
or are not satisfied with your product or the service
you receive from us please let us know by calling our
customer services team on 1300 90 50 10 .
fig 1
fig 3
fig 2
fig 4
fig 5
fig 6
fig 7
Live!-Instructions-V1.indd 1 13/12/2011 09:53

serious about sound
Pacific Ears Pty Ltd
PO Box 3081
Burleigh Town
QLD, 4220
1300 90 50 10
[email protected]
www.acscustom.com/au
Type Triple Driver
Freq. Response 16Hz - 20Khz
Resistance 40 Ohms
Isolation 26dB
Type Dual Driver
Freq. Response 16Hz - 20Khz
Resistance 29 Ohms
Isolation 26dB
T1 Live! Custom-Fit IEM T2 Live! Custom-Fit IEM
Specifications T Series Live!
In-Ear Monitors
Instructions for use
Revolutionise your performance experience
All Live! Series in-ear monitors have a pair
of built-in, sub miniature, wideband, flat
response microphones. Interfacing our
new ambient sound processor between the
wireless belt pack and your Live!
in-ear monitors, will allow you to introduce
and adjust your ambient surroundings
independently from the mix. Imagine being
able to control the outside sound and safely
control the isolation experienced by wearing
good sealing in ear monitors. With the
arrival of our Live! Series ambient processor,
isolation will become a thing of the past.
Plug in and experience your own individual
sound environment as though you have
nothing in your ears!
Your ears are now on file. Every ear impression that passes through our lab
is scanned using the latest digital technology and stored for up to four years,
so if you need any further custom product we can you can place your order
without the need for new impressions. If the impressions we have on record
are more than four years old we do request a fresh set to be on the safe side.
Live!-Instructions-V1.indd 2 13/12/2011 09:53