Panasonic WH-MDC05F3E5 User manual

© Panasonic Corporation 2013.
Order No. PAPAMY1311029CE
Mono bloc Unit
WH-MDC05F3E5
Destination
Europe
PRECAUTION OF LOW TEMPERATURE
In order to avoid frostbite, be assured of no refrigerant leakage during the installation or repairing of refrigerant circuit.
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the products dealt with in this service information by anyone else could result in serious injury or death.

2
TABLE OF CONTENTS
PAGE PAGE
1. Safety Precautions .............................................3
2. Specifications .....................................................5
2.1 WH-MDC05F3E5 ...........................................5
3. Features...............................................................7
4. Location of Controls and Components............8
4.1 Mono Bloc Unit...............................................8
5. Dimensions .......................................................18
5.1 Mono bloc Unit .............................................18
6. Refrigeration and Water Cycle Diagram ........19
7. Block Diagram ..................................................21
8. Wiring Connection Diagram ............................22
9. Electronic Circuit Diagram ..............................24
10. Printed Circuit Board .......................................26
10.1 Water System ..............................................26
10.2 Refrigerant System ......................................28
11. Installation Instruction Mono bloc Unit..........30
11.1 Select the Best Location ..............................32
11.2 Mono Bloc Unit Installation ..........................32
11.3 Piping Installation.........................................33
11.4 Connect The Cord And Cable To Mono Bloc
Unit...............................................................34
11.5 Checking And Test Cord Run Procedures ..38
12. Operation and Control .....................................39
12.1 Basic Function .............................................39
12.2 Water Pump .................................................60
12.3 Pump Down Operation [Service Mode: 01] .62
12.4 Flow Switch..................................................62
12.5 Indoor Unit Safety ........................................63
12.6 Auto Restart Control ....................................63
12.7 Indication Panel ...........................................63
12.8 Indoor Back-Up Heater Control ...................64
12.9 Tank Booster Heater Control .......................65
12.10Base Pan Heater Control (Optional) ............65
12.11Sterilization Mode ........................................66
12.12Quiet Operation............................................66
12.13Anti Freeze Control......................................67
12.14Solar Operation (Optional) ...........................68
12.15External Room Thermostat Control (Optional)
....................................................................72
12.16Three Ways Valve Control...........................73
12.17Two Ways Valve Control .............................73
12.18External OFF/ON Control ............................74
12.19Holiday Mode ...............................................75
12.20Dry Concrete Function.................................75
13. Protection Control............................................76
13.1 Protection Control For All Operations ..........76
13.2 Protection Control For Heating Operation ...78
13.3 Protection Control For Cooling Operation ...79
14. Servicing Mode.................................................80
14.1 Test Run ..................................................... 80
14.2 How To Adjust Water Flow Rate................. 80
14.3 Expansion Vessel Pre Pressure Checking . 80
15. Maintenance Guide.......................................... 81
16. Troubleshooting Guide................................... 84
16.1 Refrigeration Cycle System ........................ 84
16.2 Relationship between the Condition of the Air-
to-Water Heatpump Indoor and Outdoor Units
and Pressure and Electric Current.............. 85
16.3 Breakdown Self Diagnosis Function ........... 86
16.4 Error Codes Table....................................... 87
16.5 Self-diagnosis Method ................................ 89
17. Disassembly and Assembly Instructions ... 124
17.1 To Remove The Cabinet Front Plate ........ 124
17.2 To Remove The Cabinet Top Plate .......... 124
17.3 To Remove The Cabinet Rear Plate......... 125
17.4 To Remove Pressure Gauge .................... 125
17.5 To Remove RCCB .................................... 126
17.6 To Remove Transformer........................... 126
17.7 To Remove Water System Electronic
Controller Board........................................ 127
17.8 To Remove Refrigerant Side Control Board
Complete................................................... 128
17.9 To Remove Pressure Relief Valve and Air
Purge Valve .............................................. 129
17.10To Remove Flow Switch ........................... 129
17.11To Remove Water Pump .......................... 130
18. Technical Data ............................................... 131
18.1 Operation Characteristics ......................... 131
18.2 Heating Capacity Table............................. 135
18.3 Cooling Capacity Table............................. 135
19. Exploded View and Replacement Parts List136
19.1 WH-MDC05F3E5 (Refrigerant System)... 136
19.2 WH-MDC05F3E5 (Water System)........... 140

3
CAUTION
WARNING
WARNING
1. Safety Precautions
Read the following “SAFETY PRECAUTIONS” carefully before perform any servicing.
Electrical work and water installation work must be installed or serviced by a licensed electrician and licensed
water system installer respectively. Be sure to use the correct rating and main circuit for the model installed.
The caution items stated here must be followed because these important contents are related to safety. The
meaning of each indication used is as below. Incorrect installation or servicing due to ignoring of the instruction
will cause harm or damage, and the seriousness is classified by the following indications.
This indication shows the possibility of causing death or serious injury.
This indication shows the possibility of causing injury or damage to properties.
The items to be followed are classified by the symbols:
Carry out test run to confirm that no abnormality occurs after the servicing. Then, explain to user the operation,
care and maintenance as stated in instructions. Please remind the customer to keep the operating instructions for
future reference.
1. Do not modify the machine, part or material during repairing service.
2. If wiring unit is supplied as repairing part, do not repair or connect the wire even partial wire break. Exchange the whole wiring unit.
3. Do not wrench the fasten terminal. Pull it out or insert it straightly.
4. Do not install Mono bloc unit near handrail of veranda. When installing Mono bloc unit at veranda of high rise building, child may climb
up to Mono bloc unit and cross over the handrail and causing accident.
5. Do not use unspecified cord, modified cord, join cord or extension cord for power supply cord. Do not share the single outlet with other
electrical appliances. Poor contact, poor insulation or over current will cause electrical shock or fire.
6. Do not tie up the power supply cord into a bundle by band. Abnormal temperature rise on power supply cord may happen.
7. Do not insert your fingers or other objects into the unit, high speed rotating fan may cause injury.
8. Do not sit or step on the unit, you may fall down accidentally.
9. Keep plastic bag (packaging material) away from small children, it may cling to nose and mouth thus causing suffocation.
10. Do not use pipe wrench to install refrigerant pipe. Using pipe wrench may deform the pipes and cause unit malfunction.
11. Do not purchase unauthorized electrical parts for installation, service, maintenance and etc.. They might cause electrical shock or fire.
12. Do not modify the wiring of Mono bloc unit for installation of other components (i.e. heater, etc). Overloaded wiring or wire connection
points may cause electrical shock or fire.
13. For electrical work, follow local wiring standard, regulation and this installation instruction. An independent circuit and single outlet must be
used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.
14. For water circuit installation work, follow to relevant European and national regulations (including EN61770) and local plumbing and building
regulation codes.
15. Must engage an authorized dealer or specialist for installation. If installation is defective, it will cause water leakage, electrical shock or fire.
16. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical shock or fire.
17. Only use the supplied or specified installation parts. Else, it may causes Mono bloc unit vibrate, fall, water leakage, electrical shock or fire.
18. Install at a flat, strong and firm location which is able to withstand the Mono bloc unit’s weight. If the location is slanting, or strength is not
enough the set will fall and cause injury.
This symbol denotes item that is PROHIBITED from doing.

4
CAUTION
19. This equipment is strongly recommended to be installed with Residual Current Device (RCD) on-site according to the respective national
wiring rules or country-specific safety measures in terms of residual current.
20. The unit is only for use in a closed water system. Utilization in an open water system may lead to excessive corrosion of the water piping and
risk of incubating bacteria colonies, particularly Legionella, in water.
21. If there is any doubt about the installation procedure or operation, always contact the authorized dealer for advice and information.
22. Select a location where in case of water leakage, the leakage will not cause damage to other properties.
23. When installing electrical equipment at wooden building of metal lath or wire lath, in accordance with electrical facility standard, no electrical
contact between equipment and building is allowed. Insulator must be installed in between.
24. This installation may be subjected to building regulation approval applicable to respective country that may require to notify the local authority
before installation.
25. Any work carried out on the Mono bloc unit after removing the front panel which is secured by screws, must be carried out under the
supervision of authorized dealer and licensed installation contractor.
26. This unit must be properly earthed, the electrical earth must not be connected to a gas pipe, water pipe, the earth of a lightening rod or a
telephone. Otherwise there is a danger of electrical shock in the event of an insulation breakdown or electrical earth fault in the Mono bloc unit.
27. When replace refrigeration circuit components, confirm on usage of specified refrigerant type. Using of refrigerant other than the specified type
may cause product damage, burst and injury etc.
28. Do not add or replace refrigerant other than the specified type. Equipment may damage or deteriorate in safety due to usage of other
refrigerant.
1. Do not install the Mono bloc unit in areas where there is a risk of flammable gas leakage. There is a risk of fire if flammable gas
accumulates near or around the Mono bloc unit.
2. Do not release refrigerant during piping work for installation, re-installation and during repairing a refrigeration parts. Take care of the
liquid refrigerant, it may cause frostbite.
3. Make sure the power supply cord does not contact with hot part (i.e. water piping). High temperature may cause insulator of power
supply cord damage hence electrical shock or fire.
4. Do not touch the sharp aluminum fins or edges of metal parts.
If you are required to handle sharp parts during installation or servicing, please wear hand glove.
Sharp parts may cause injury.
5. Do not apply excessive force to water pipes that may damage the pipes. If water leakage occurs, it will cause flooding and damage to
other properties.
6. Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water leakage may happen and may cause
damage to properties of the user.
7. The piping installation work must be flushed before the Mono bloc unit is connected to remove contaminants. Contaminants may damage the
Mono bloc unit components.
8. Select an installation location where it is accessible for maintenance.
9. Power supply connection to Mono bloc unit.
Power supply point should be in easily accessible place for power disconnection in case of emergency.
Must follow local national wiring standard, regulation and this installation instruction.
Strongly recommended to make permanent connection to a circuit breaker. It must be a double pole switch with a minimum 3.0 mm gap.
- Use approved 30A circuit breaker for power supply 1
- For electrical heater connection to main for power supply 2 (either or )
Use approved 15A/16A circuit breaker (Backup Heater only)
Use approved 30A circuit breaker (Backup Heater + Booster Heater)
10. Ensure the correct polarity is maintained throughout all wiring. Otherwise, it will cause electrical shock or fire.
11. After installation, the installer is obliged to verify correct operation of the Mono bloc unit. Check the connection point for water leakage during
test run. If leakage occurs, it will cause damage to other properties.
12. Installation work.
Four or more people are required to carry out the installation work. The weight of Mono bloc unit might cause injury if carried by less than four
people.

5
2. Specifications
2.1 WH-MDC05F3E5
Item Unit Refrigerant System
Performance Test Condition EN 14511
Condition (Ambient/Water) A35W7 -
kW 4.50 -
BTU/h 15300 -
Cooling Capacity
kcal/h 3870 -
W/W 3.33 -
EER kcal/hW 2.87 -
Condition (Ambient/Water) A7W35 A2W35
kW 5.00 4.80
BTU/h 17100 16400
Heating Capacity
kcal/h 4300 4130
W/W 5.08 3.75
COP kcal/hW 4.37 3.23
Air Flow m3/min (ft3/min) Cooling: 57.1 (2016)
Heating: 43.3 (1529)
Refrigeration Control Device Expansion Valve
Refrigeration Oil cm3FV50S (800)
Refrigerant (R410A) kg (oz) 1.42 (50.1)
Type Hermetic Motor (Rotary)
Motor Type Brushless (4-poles)
Compressor
Rated Output kW 1.70
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W —
Output Power W 60
Fan
Fan Speed rpm Cooling: 700
Heating: 580
Fin material Aluminium (Pre Coat)
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 30 × 17
Heat Exchanger
Size (W × H × L) mm 38.1 × 762 × 903.8:873.8
Item Unit Mono Bloc Unit
Height mm (inch) 865 (34-1/16)
Width mm (inch) 1283 (50-17/32)
Dimension
Depth mm (inch) 320 (12-5/8)
Net Weight kg (lbs) 107 (236)
dB-A Cooling: 47
Heating: 47
Cooling: -
Heating: -
Noise Level
Power Level dB Cooling: 65
Heating: 65
Cooling: -
Heating: -
ø Single
V 230
Power Source (Phase, Voltage, Cycle)
Hz 50
Input Power kW Cooling: 1.35
Heating: 0.985
Cooling: -
Heating: 1.28
Maximum Input Power For Mono Bloc Unit kW 4.26

6
Item Unit Mono Bloc Unit
Power Supply 1: Phase (ø) / Max. Current (A) / Max. Input Power (W) Single / 19.5 / 4.26k
Power Supply 2: Phase (ø) / Max. Current (A) / Max. Input Power (W) Single / 13.0 / 3.00k
Power Supply 3: Phase (ø) / Max. Current (A) / Max. Input Power (W) - / - / -
Starting Current A 6.1
Running Current A Cooling: 6.10
Heating: 4.50
Cooling: -
Heating: 5.90
Maximum Current For Mono Bloc Unit A 19.5
Power Factor % Cooling: 96
Heating: 95
Cooling: -
Heating: 95
Power factor means total figure of compressor and outdoor fan motor.
Thermostat Electronic Control
Protection Device Electronic Control
Item Unit Water System
Performance Test Condition EN 14511
Outdoor Ambient °C Cooling: 16 ~ 43
Heating: 20 ~ 35
Operation Range
Water Outlet °C Cooling: 5 ~ 20
Heating: 25 ~ 55
Internal Pressure Differential kPa Cooling: 16.0
Heating: 19.6
Inlet mm (inch) 30 (1-3/16)
Water Pipe Diameter Outlet mm (inch) 30 (1-3/16)
Water Drain Hose Inner Diameter mm (inch) 15.00 (19/32)
Motor Type Brushless DC Motor
No. of Speed 7 (Software Selection)
Pump
Input Power W 47
Type Brazed Plate
No. of Plates 48
Size (H × W × L) mm 81 × 93 × 325
Hot Water Coil
Water Flow Rate l/min (m3/h) Cooling: 12.9 (0.8)
Heating: 14.3 (0.9)
Pressure Relief Valve Water Circuit kPa Open: 300, Close: 265 and below
Flow Switch Magnetic Lead Switch
Protection Device A Residual Current Circuit Breaker (40)
Volume I 6
Expansion Vessel MWP bar 3
Capacity of Integrated Electric Heater kW 3.00
Note:
Cooling capacities are based on outdoor air temperature of 35°C Dry Bulb with controlled water inlet temperature
of 12°C and water outlet temperature of 7°C.
Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled water inlet temperature of 30°C and water outlet temperature of 35°C.
Specification are subjected to change without prior notice for further improvement.
Flow rate indicated are based on nominal capacity adjustment of leaving water temperature (LWT) 35°C and T
= 5°C.

7
3. Features
Inverter Technology
- Energy saving
High Efficiency
Compact Design
Environment Protection
- Non-ozone depletion substances refrigerant (R410A)
Easy to use control panel
- Auto mode
- Holiday mode
- Dry concrete function
- Weekly timer setting
A-class energy efficiency pump
- Water pump speed can be set by selection at control panel
Protection Feature
- Random auto restart after power failure for safety restart operation
- Gas leakage protection
- Prevent compressor reverse cycle
- Inner protector to protect compressor
Serviceability Feature
- Breakdown Self Diagnosis function
- System Status Check Buttons for servicing purpose
- System Pumpdown Button for servicing purpose
- Front maintenance design for mono bloc unit
Operation Condition
Water outlet temperature (°C) Ambient temperature (°C)
Maximum 55 35
HEATING Minimum 25 -20
Maximum 20 43
COOLING Minimum 5 16
NOTICE : When the outdoor temperature is out of the above temperature range, the heating capacity will drop significantly
and mono bloc unit might stop for protection control. The unit will restart automatically after the outdoor temperature
returns to the specified range.

8
4. Location of Controls and Components
4.1 Mono Bloc Unit
Top P la te
A
ir inlet (rear)
Air inlet (side)
A
ir outlet
Cabinet Front Plate
Handle
(2 pieces front and 2 pieces behind)

9
4.1.1 Main Components
Component name
PCB
Pressure relief valve
Flow switch
Pressure gauge
Water pump
RCCB
Cable cover
Cabinet front plate
Connector name
Water inlet
Water outlet
Cabinet top plate
Overload protector
Heater assembly
Expansion vessel
Cover
Air purge valve
Plug
(VIEW
WITHOUT
COVER)
DETAIL B DETAIL A
View without cabinet top plate
(VIEW
WITHOUT
PCB)
1
2
a
b
3
4
5
6
7
8
9
10
11
12
13
14
15

10
4.1.2 Location of Control
4.1.2.1 Remote Control
The user interface allows the installer and user to setup, use and maintain the unit.
OPERAT ION
ACTUAL
HEATE R
BOOSTER
QUIET
SETTING
STATUS
SERVICE
AUTO
HEAT
COOL
TANK
HE ATE R
FORCE
°C
°C
ON
OFF
MON TUE WED THU FRI SAT SUN
hr
hr
kwh
OFF/ON Button
This button starts or stops the mode operation function of the unit.
Operation LED
This LED indicates the unit is in operation.
External Thermo Controller Connected Display
This LCD show the external thermo controller connected display.
Force Heater Request OFF/ON Indicator
This icon indicates force heater request OFF/ON mode operation.
Backup Heater Enabled/Disabled Indicator
This icon indicates backup heater enabled/disabled mode operation.
Quiet Mode Indicator
This icon indicates quiet mode operation.
Tank Mode Indicator
This icon indicates tank mode operation.
Cool Mode OFF/ON Indicator
This icon indicates cooling mode OFF/ON operation.
Heat Mode OFF/ON Indicator
This icon indicates heating mode OFF/ON operation.
Auto Mode OFF/ON Indicator
This icon indicates auto mode OFF/ON operation.
Solar Display
This LCD show the solar display.
Caution (Tank Temperature above 60°C) Indicator
This LCD show the Caution display.
Timer/Clock Setting Display
This LCD show the weekly schedule timer setting and clock display.
Outdoor Ambient Temperature Display
This LCD show the outdoor ambient temperature.
Water Outlet Temperature Display
This LCD show the water outlet temperature.
Backup Heater Actual (OFF/ON) Indicator
This icon indicates backup heater actual (OFF/ON) operation.
Booster Heater Actual (OFF/ON) Indicator
This icon indicates booster heater actual (OFF/ON) operation.
System Setting Mode OFF/ON Indicator
This icon indicates the system setting mode request OFF/ON display.
System Status Check Mode OFF/ON Indicator
This icon indicates the status check mode request OFF/ON display.
System Service Mode OFF/ON Indicator
This icon indicates the system service mode request OFF/ON display.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
7
8
910 11 12 13 14
15 16
17
6
18
19
20

11
4.1.3 To adjust initial settings
Dealer
Select menus and determine settings according to the system available in the
household. It is recommended that all alterations of settings are done by an
authorised dealer or specialist.
• After initial installation, you may manually adjust the settings.
The initial setting remains active until the user changes it.
• The control panel can be used for multiple installations.
• Ensure the operation LED is OFF before setting.
• The system may not work properly if set wrongly. Please consult
an authorised dealer.
1Press and simultaneously and hold for
5 seconds until the display shows SETTING STATUS.
2Press or to select the menu.
3Press to enter the menu.
4Press or to select YES/NO, or other options.
YES: to enable the menu
NO:to disable the menu
5Press to confirm.
Remote Control
DisplayOperation LED
DisplaySettingMenu (1 ~ 20)
1
Room Thermostat Connection
To select whether or not to connect to the optional room thermostat. YES NO
NO
NO
NO
NO
NO
2
Indoor Backup Heater Selection
To reduce the heater power if unnecessary.
*Options of kW vary depending on the model.
*3 kW / 6 kW /
9 kW
3
Water System Freeze Prevention
To activate or deactivate the water freeze prevention when the system is OFF. YES
4
Tank Connection
To select whether or not to connect to the optional water tank unit.
Note: If NO is selected, menus 5 to 15 are skipped.
YES
5
Solar Priority
To select the use of solar panel for heating up the water tank. YES
6
*
1,
*
2
Cooling Priority
To choose the room cooling as priority during COOL + TANK mode.
Note: If YES is selected, menus 8 and 9 are skipped for COOL + TANK mode.
YES
7
Heating Priority
To select the room heating as priority during HEAT + TANK mode.
Note: If YES is selected, menus 8 and 9 are skipped for HEAT + TANK mode.
YES
8
*
1,
*
2
Cooling/Heating Operation Interval
To set the interval for COOL or HEAT mode during COOL + TANK or HEAT +
TANK mode.
Note: If YES is selected in menus 6 and 7, this menu is skipped.
0.5 hours ~
10 hours
9
*
1
Tank Heat-up Interval
To set the interval for the water tank during COOL + TANK or HEAT + TANK
mode.
Note: If YES is selected in menus 6 and 7, this menu is skipped.
5 minutes ~
1 hour 35 minutes

12
10
Booster Heater
To activate or deactivate the water tank’s booster heater.
Note: If NO is selected, menu 11 is skipped.
YES NO
NO
NO
B
11
Booster Heater Delay Timer
To delay time for the booster heater to activate while the system is heating up
the water tank.
20 minutes ~
1 hour 35 minutes
• Do not use the system during sterilisation in order to prevent scalding with hot water, or overheating of shower.
• Ask an authorised dealer to determine the level of sterilisation function field settings according to the local laws and
regulations.
12
Sterilisation
To sterilise the water tank, if required.
Note: If NO is selected, menus 13 to 15 are skipped.
YES
13
Sterilisation Day & Time
To set timer for sterilisation.
(Only once a week. Operates even under a standby condition)
Monday ~ Sunday
0:00 ~ 23:50
14
Sterilisation Temperature
To set the temperature of sterilisation. 40 °C ~ 75 °C
15
Continuation of Sterilisation
To maintain heating temperature in order to complete the sterilisation.
5 minutes ~
1 hour
16
Base Pan Heater
To select whether or not to connect to the optional base pan heater.
Note: If NO is selected, menu 17 is skipped.
YES
17
Base Pan Heater type
Type A - The base pan heater activates only during deice operation.
sierutarepmettneibmaroodtuonehwsetavitcaretaehnapesabehT-BepyT
5 °C or lower.
A
18
*1, *2Cool Outdoor Temperature setting
To set the outdoor ambient temperature for the AUTO mode to change from
HEAT to COOL.
5 °C ~ 25 °C
19
*1, *2Heat Outdoor Temperature setting
To set the outdoor ambient temperature for the AUTO mode to change from
COOL to HEAT.
5 °C ~ 25 °C
20
Dry Concrete
During construction to dry the concrete under a preset temperature.
Do not use this menu for any other purposes and in period other than during
construction.
1 day ~ 99 days
User
Remote control preparation
1Press .
2Press or to set the current day.
3Press to confirm.
4Repeat steps 2and 3to set the current time.
■ Note:
:wolebsesacnitesebotdeenemitdnayadtnerrucehT•
- When the power is turned on for the first time.
ehtnodenrutsawrewopehtecnisdespalesahemitgnolA-
last time.
• The current time that has been set will be the standard time for
all the timer operations.
Caution Indicator (Tank Temperature above 60 °C)
Dealer
Operation/settings to be done only by the authorised dealer/specialist.
User
Operation/settings to be done by the authorised dealer/specialist or user.
*
1
The system is locked to operate without COOL mode. It can be unlocked only by authorized installers or our authorized service partners.
*
2
Only displayed when COOL mode is unlocked (Means when COOL mode is available).

13
4.1.4 How to use
User
Enjoy quiet operation
Press .
• This operation reduces the noise of mono bloc unit.
The operation may cause heating/
*
1
cooling ability to
decrease.
User
System status check mode
1sserP .
(The display shows STATUS.)
2sserP or to check the selected mode.
• Dry concrete (does not show during normal
operation)
• The Water Inlet Temperature
• Tank Temperature
• Compressor Running Frequency
• Error History
• Heat mode total power consumption (Up to 999 days)
• * 1Cool mode total power consumption (Up to 999 days)
• Tank mode total power consumption (Up to 999 days)
• Press to exit the STATUS mode.
■ Note:
• Once the STATUS mode is entered, the display
shows STATUS.
• The STATUS mode cannot be activated when the
display shows SETTING.
• The total power consumption is an estimated value
based on AC 230 V and may differ from value
measured by precise equipment.
■
Note: In normal operation, the , and buttons are not in use.
User
Turn on or off the syste
m
Press .
W
hen the system is ON, the operation LED is lit and the
actual water outlet temperature and outdoor ambient
t
emperature are shown on the display.
User
Select operation mode
Press to select operation mode.
AUTO • Depending on the preset outdoor
temperature, the system selects HEAT or
*
1
COOL operation mode.
AUTO
+ TANK
• Depending on the preset outdoor
temperature, the system selects HEAT +
TANK or *
1
COOL+ TANK operation mode.
HEAT rehtiesinoitarepoTAEHroolf/lenapehT•
turned ON or OFF.
• The mono bloc unit provides heat to the
system.
HEAT
+ TANK
• The mono bloc unit provides heat to the
sanitary tank and the system.
• This mode cannot be selected when the
sanitary water tank is not installed.
TANK • The sanitary water tank is either turned
ON or OFF.
• The mono bloc unit provides heat to the
sanitary water tank.
COOL
+ TANK
• The mono bloc unit provides cooling to
the system.
• The system controls the booster heater in
he sanitary water tank.
COOL • The panel is either turned ON or OFF.
• The outdoor unit provides cooling to the
indoor unit.
User
Initiate the backup heater
Press .
• The backup heater provides extra heat at low outdoor
temperature. The backup heater is possible only in the
heat mode.
• Once the backup heater is set, it is automaticall
y
operated when conditions are fulfilled.
• To disable the backup heater, pres
s
again.
The system is turned off by an external switch.
*
1,
*
2
*
1,
*
2

14
Dealer Operation/settings to be done only by the authorised dealer/specialist.
User Operation/settings to be done by the authorised dealer/specialist or user.
Dealer
System temperature setting
Temperature settingDisplay
The system controls the temperature for each menu based on the
outdoor ambient temperature.
• To set or change the temperatures, make sure to contact your
nearest authorised dealer.
1dlohdnasserP for 5 seconds to enter the
temperature range setting mode.
(The display shows SETTING.)
2sserP or to select a menu.
3sserP to enter the menu.
4sserP or to set the desired temperature.
5sserP to confirm the setting.
• Repeat steps 2to 5to set other menus.
User
Checking the temperature range
1dlohdnasserP for 5 seconds to enter the temperature range setting mode.
2sserP or to select a menu.
• Press to exit.
Menu Temperature
setting Display
C°51~C°51-.erutarepmettneibmaroodtuowolfognitteS
HEAT
C°51~C°51-.erutarepmettneibmaroodtuohgihfognitteS
Setting of water outlet temperature at low outdoor ambient
temperature. 25 °C ~ 55 °C
Setting of water outlet temperature at high outdoor ambient
temperature. 25 °C ~ 55 °C
During HEAT mode, the water outlet
temperature is adjusted as is shown the
diagram on the right.
It is performed within the preset temperature
range.
<Water outlet
temperature>
<Outdoor ambient temperature>
max. water temp.
min. water temp.
Setting of outdoor ambient temperature to turn OFF heating
operation during HEAT mode. 5 °C ~ 35 °C
5 °C ~ 20 °C
HEAT
Setting of outdoor ambient temperature to turn ON the backup
heater. -15 °C ~ 20 °C HEATER
Setting of water outlet temperature during *1 COOL mode.
*
1,
*
2
COOL
C°57~C°04.erutarepmetknatretawyratinasfognitteS TANK
*
1
The system is locked to operate without COOL mode. It can be unlocked only by authorized installers or our authorized service partners.
*
2
Only displayed when COOL mode is unlocked (Means when COOL mode is available).

15
User
Shifting the water temperature
Desired temperature setting
This easil
y
shifts the water outlet temperature if the settin
g
is
undesirable.
1sserP to enter the water temperature shifting mode.
2sserP to change setting.
3sserP or to set the desired temperature.
(temperature range: -5 °C ~ 5 °C)
Temperature setting
+5
-5
Shift value
<Water outlet
t
emperature>
<Outdoor ambient temperature>
4sserP to confirm the setting.
■
Note:
• Pres
s
or wait for 30 seconds to exit the SETTING mode.
• The set temperature will be saved in the s
y
stem once confirmed.
• The SETTING mode cannot be activated when the SERVICE and STATUS indicators are ON.
• The s
y
stem will shift the temperature within water outlet temperature ran
g
e.
User
Holiday mode
• B
y
settin
g
the da
y
(
s
)
in holida
y
mode, it promotes ener
gy
savin
g
while you are on holiday, and enables the system to resume at the
preset temperature after your holiday.
• Ensure that the s
y
stem is OFF before settin
g
.
• The s
y
stem will resume operation automaticall
y
at 00:00 am after
the holiday.
• The da
y
the HOLIDAY mode was set is counted as da
y
1.
Desired days
Example:
Settin
g
the holida
y
mode on June 21, 08:00 am. B
y
settin
g
3 da
y
s,
t
he s
y
stem resumes operation on June 24, 00:00 am.
1sserP to enter the HOLIDAY mode.
2sserP or to set the desired days.
(Setting range: 1 day ~ 999 days)
3sserP to confirm the setting.
■
Note:
• Pres
s
or wait 30 seconds to exit the HOLIDAY mode.

16
User
Weekly timer setting
Promotes energy saving by allowing you to set up to 6
programmes in any given day.
Indicates the next timer operation
programme
Day to be selected
Indicates the next timer
operation day
Programme number in a day
OFF Timer
ON Timer
Lights up if Timer operation is selected
1sserP to enter the timer setting mode.
2sserP or to select your desired day.
3sserP to confirm your selection.
4sserp,gniknilbeblliw”1“ to set
programme 1.
5Press to select ON or OFF timer.
6sserP or to select your desired time.
You can set ,, and the water
temperature setting.
To modify current timer programme
or add new timer programme
1
Perform steps
1
to
7
of “Weekly timer
setting” to modify existing timer programme, or
add any timer programme.
To cancel current timer programme
1sserP to enter day.
2sserP or until your desired day is shown,
press to enter programme setting.
3sserP or until your desired day is shown.
Press to cancel the programme and ▼will
disappear.
To disable/enable Weekly Timer
•To disable weekly timer setting, press , then
press .
•To enable previous weekly timer setting, press ,
then press .
Dealer
Operation/settings to be done only by the authorised dealer/specialist.
User
Operation/settings to be done by the authorised dealer/specialist or user.
7sserP to confirm programme 1. The selected
day will be highlighted with ▼.
• After 2 seconds, the display will move to the next
programme. Repeat steps 4to 7to set
programmes 2 to 6.
• During timer setup, if no button is pressed within
30 seconds, or if the is pressed, the setting at
that moment is confirmed and timer setup is ended.
To check current timer programme
1sserP to enter timer mode and press
to enter day setting.
2sserP or until your desired day is shown,
press to confirm your selection.
3sserP or to check the set programmes.
■
Note:
• You may set the timer for each day of the week (Monday to Sunday) with 6 programmes per day.
• When the system is switched on by the timer, it will use the previously set temperature to control the water outle
t
temperature.
• The same timer programme cannot be set on the same day.
• You may also select 2 or more days with the same timer setting.

17
Dry Concrete Function
• During construction to dry the concrete under a preset temperature.
1sserP and simultaneously and hold for 5 seconds until the display shows “ ”.
2sserP .
(The display shows “ ”).
3sserP to select day.
Press or to set the desired temperature.
4sserP to confirm the selection.
5petstaepeR 3and 4to set other days and temperature.
• Press to exit.

18
5. Dimensions
5.1 Mono bloc Unit
Unit: mm
<Top View
>
<Front View> <Side View><Side view>
(579)
152 980
1283
303
319 266
94
865
480
70
172
(10)
(10)
(20)
152
400 355 320
(10)

19
6. Refrigeration and Water Cycle Diagram
Mono bloc Unit
Pipe
Temp.
Sensor
Pipe
Temp.
Sensor
Hex
Water Outlet
Temp. Sensor
Pipe
Temp.
Sensor
Pipe
Temp.
Sensor
Air
Temp.
Sensor
Backup Heater
Outdoor
Side
Expansion
Vessel
Pressure
Relief
Valve
Water
Flow
Switch
Water
Pump
Water
Inlet
(Connect
to
Sanitary
Tank)
Water
Outlet
(Connect
to
Sanitary
Tank)
Drain
Refrigerant Cycle (Heating)
Water Cycle
Heat
Exchanger
Heat
Exchanger
Strainer Strainer
Receiver
4-Way
Valve
Gas
Side
(3-Way
Valve)
Liquid
Side
(2-Way
Valve)
Pressure
Switch
High Pressure
Sensor
Compressor Discharge
Temp. Sensor
Compressor Tank
Temp. Sensor
Compressor
Water
Pressure
Gauge
Capillary
Tube
Muffler
Expansion
Valve

20
To Water Inlet
Mono bloc Unit
From Water Outlet
Mono bloc Unit
Connect to Mono bloc Unit
main electronic controller
(Water System)
Remote Control
Room Thermo (Optional)
Fan Coil Unit
(Heating / Cooling)
Panel Heater Uni
t
(Heating)
Floor Heating Panel
(Heating)
Cold Water
Supply
Connect to
Mono bloc Unit
Terminal Board
(Water System)
3-Way Valve 2-Way Valve
OLP
Heater 1 (3kW)
THs
Sanitary Tank
Solar Unit
(Optional)
THt
HEX
Indoor
Side
OPERATION
ACTUAL
HEATER
BOOS T E R
QUIET
SETTING
STATUS
SERVICE
AUTO
HEAT
COOL
TANK
HEAT E R
FORCE
°C
°C
ON
OFF
MON TUE WED THU FRI SA T SUN
hr
hr
kwh