Panasonic AJ-PX270 Service manual

P2 Camera - TVU networks
Direct connection live streaming
Setting Guide
Panasonic Corporation
Media & Entertainment Business Division
Jan.22, 2019

As of Dec.25, 2018
Panasonic P2 camera/recorder product number Version
AJ-PX270 36.72-00-0.00
AJ-PX5100 25.22-00-0.00
AJ-PX5000 40.73-00-0.00
AJ-PX800 37.50-00-0.00
AJ-PX380 39.96-00-0.00
AJ-PG50 33.89-00-0.00
1. Confirm product and version to support integration
Please refer to Panasonic web site regarding P2 products version and upgrade.
https://eww.pass.panasonic.co.jp/p2ui/guest/TopLogin.do?lang=en&category=pav
P2 Camera - TVU networks direct connection live streaming
Setting Guide
TVU networks receiver product number Version
VS3500 6.5
TX3200 6.5
Please consult TVU networks about receiver product version and the details of
network settings such as TCP, UDP port.
http://www.tvunetworks.com/
[ 1/6 ]

2. Configure P2 device
Prepare SD card for P2 – TVU communication
2-1. Format a SD card by P2 product such as PX270 camera.
[MENU]-[CLIP]-[FORMAT]-[SD CARD]
2-2. Create a configuration file for TVU in the SD card by using application software
named P2netGen.exe uploaded on the following URL.
https://eww.pass.panasonic.co.jp/pro-av/support/content/download/EN/ep2main/nw_setting_e.htm
1
2
3
3. Connect wired LAN or Wi-Fi/4G/LTE device to camera.
Note:
Please refer to the following Panasonic web site about confirmed 4G/LTE USB modems
and Wi-Fi wireless modules for P2 products.
https://pro-av.panasonic.net/en/p2hd.html
(1) Select “Streaming”.
(2) Select “TVU”.
(3) Copy file to SD card by clicking
“Export” button.
[ 2/6 ]

4-2. Codec settings
[MENU]-[SYSTEM MODE]-[LINE&FREQ]
[MENU]-[SYSTEM MODE]-[REC FORMAT]
[MENU]-[RECORDING SETUP]-[DUAL CODEC SETTINGS]-[STREAMING MODE]
Note:
- Select either "1080-59.94i", "1080-50i", "720-59.94P" or "720-50P" for LINE&FREQ
- When changing LINE&FREQ setting, P2 camera restarts.
- "LOW", "AVC-G6" or "AVC-G(QoS)" of STREAMING MODE might not be selected
depending on the combination of LINE&FREQ and REC FORMAT.
Insert the SD card with configuration file into a SD card slot.
Note:
Please do not confuse SD card slot with microP2 card slot.
PX270
PX380
4. Menu settings
4-1. Network settings
Select network from the menu according to the actual connection.
[MENU]-[NETWORK SETUP]-[NETWORK SEL]="WLAN" , "4GLTE" or "LAN"
Note:
- P2 camera might restart when changing menu depending on the setting.
- You can confirm the network connection status on the menu:
[MENU]-[NETWORK SETUP]-[NETWORK TOOLS]-[STATUS DISPLAY]
[ 3/6 ]

4-3. Streaming settings
[MENU]-[RECORDING SETUP]-[DUAL CODEC SETTINGS]-[CODEC USAGE]="STREAMING"
[MENU]-[NETWORK SETUP]-[STREAMING SETTINGS]-[START TRIGGER]="CAMERA"
[MENU]-[NETWORK SETUP]-[STREAMING SETTINGS]-[SETTING DATA]="SD CARD"
[MENU]-[RECORDING SETUP]-[DUAL CODEC SETTINGS]-[QoS MAX RATE]
[MENU]-[RECORDING SETUP]-[DUAL CODEC SETTINGS]-[QoS MIN RATE]
Note:
The setting from TVU receiver is prioritized for QoS MAX RATE.
You cannot set QoS MAX RATE lower than QoS MIN RATE.
Please leave the default QoS MAX RATE setting for normal use.
Please set minimum value for QoS MIN RATE for normal use.
p2stream.cnf
SD CARD
NETWORK STATUS
IP ADDRESS: 192.168.0.1
SUBNET MASK: 255.255.255.0
DEFAULT GATEWAY: 192.168.0.254
DNS1: 0.0.0.0
######## TVU Networks information ########
TVU ID: XXXXXXXXXXXXXXXX
[DISP/MODE CHK] switch
TVU RECEIVER
START TRIGGER CAMERA
SETTING DATA SD CARD
SERVER ADDR. TVU Networks
RTSP PORT
LOAD(SD CARD)
SAVE(SD CARD)
START OFF
EXIT
5. Confirmation of the settings
[MENU]-[NETWORK SETUP]-[STREAMING SETTINGS]
[ 4/6 ]

TVU Receiver configuration should be modified to receive Panasonic streaming.
This should be remotely done by TVU Support.
To start a live transmission, simply select the P2 device in the source list and press
the LIVE button. The stream will begin within a few seconds.
To stop a live transmission, press the STOP button
Please note, the TVU bitrate, latency (delay) and VBR/CBR functions do not affect
P2 transmission.
6. Configure TVU Receiver
Please consult TVU networks support about TVU Receiver configuration for
pairing between Panasonic camera/recorder and TVU Receiver.
http://www.tvunetworks.com/support/
TVU Support can also create a custom nickname for the camera
A P2 icon will appear on the TVU Receiver GUI once pairing is complete.
NOTE: P2 devices do not provide an index picture to the TVU GUI.
[ 5/6 ]

Note:
TVU Receiver is able to set maximum bit rate for AVCG (QoS) and SHQ (QoS) mode
of STREAMING MODE on P2 camera/recorder.
- Available maximum bit rate to be set is on QoS MAX RATE menu list.
- If TVU Receiver setting bit rate is different from the list above,
the bit rate is cut down to the nearest setting value of the list.
- If TVU Receiver setting bit rate is smaller than QoS MIN RATE setting value,
codec bit rate is fixed as TVU Receiver setting.
- When TVU Receiver does not set maximum bit rate, the codec bit rate is set
as QoS MAX RATE setting value of camera menu.
- In the case of fixed bit rate settings like AVC-G6, HQ and LOW of STREAMING MODE,
Receiver’s bit rate setting is ignored and codec bit rate is fixed depending on the
video resolution.
When the latency is less than 1000msec, live streaming might be unstable regardless
network latency.
The latency is fixed after starting streaming. Please stop streaming if you would like
to change the latency setting.
Some of the functions are not available.
(e.g. IFB, Message, File Download, GPS, Camcorder control).
[ 6/6 ]