Panasonic Digital Palmcorder PV-GS69 User manual

Before attempting to connect, operate or adjust this product, please
read these instructions thoroughly.
LSQT1070 A
PV-GS69
PV-GS39
PV-GS29
Digital Video Camcorder
Operating Instructions
Models No.
(PV-GS69 Shown)
PL

2
WARNING :
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
You have purchased one of the most
sophisticated and reliable products on the market
today. Used properly, we’re sure it will bring you
and your family years of enjoyment. Please take
time to fill in the information on the right.
The serial number is on the tag located on the
underside of your Camcorder. Be sure to retain
this manual as your convenient Camcorder
information source.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
The above markings are located on the appliance bottom cover.
Your Camcorder is designed to record and play back in Standard Play (SP) mode and Long (LP)
mode.
It is recommended that only cassette tapes that have been tested and inspected for use in Camcorders
with the mark be used.
Thank you for choosing Panasonic!
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any inside part of this unit.
Things You Should Know
Safety Precautions
AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN.
DO NOT ALLOW CHILDREN TO HANDLE THE SD CARD.
CAUTION:
TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
• Since this product gets hot during use, operate it in a well ventilated place; do not install this
equipment in a confined space such as a bookcase or similar unit.
WARNING

3
Declaration of Conformity
Trade Name : Panasonic
Model No. : PV-GS29/PV-GS39/PV-GS69
Responsibility Party : Panasonic Corporation of North America
Address : One Panasonic Way Secaucus New Jersey 07094
Telephone Number : 1-800-211-PANA(7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
To assure continued compliance, follow the attached installation instructions and use only shielded
interface cables when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
06'306'3
06'3
- U.S.A. CONSUMERS Only-
A lithium ion/polymer battery that is recyclable powers the product you
have purchased. Please call 1-800-8-BATTERY for information on how
to recycle this battery.
U.S.A. CONSUMERS: ATTENTION:

4
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or the table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when it will be left unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

5
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing.
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
WARNING
CAUTION
Precautions
USE & LOCATION
●TO AVOID SHOCK HAZARD ... Your
Camcorder and power supply should not be
exposed to rain or moisture. Do not connect the
power supply or operate your Camcorder if it
gets wet. Your Camcorder has been designed
for outdoor use, however it is not designed to
sustain direct exposure to water, rain, sleet,
snow, sand, dust, or a direct splashing from a
pool or even a cup of coffee. This action could
permanently damage the internal parts of your
Camcorder. Do not attempt to disassemble this
unit. There are no user serviceable parts inside.
Unplug your Camcorder from the power supply
before cleaning.
●DO NOT AIM YOUR CAMCORDER AT
THE SUN OR OTHER BRIGHT OBJECTS
●DO NOT LEAVE THE CAMCORDER
WITH THE EVF AIMED DIRECTLY
AT THE SUN AS THIS MAY CAUSE
DAMAGE TO THE INTERNAL PARTS OF
THE EVF
●DO NOT EXPOSE YOUR CAMCORDER
TO EXTENDED HIGH TEMPERATURE
... Such as, in direct sunlight, inside a closed
car, next to a heater, etc... This action could
permanently damage the internal parts of your
Camcorder.
●AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the tape and inside the
unit.
●
DO NOT LEAVE YOUR CAMCORDER
OR THE POWER SUPPLY TURNED ON
WHEN NOT IN USE.
●STORAGE OF YOUR CAMCORDER ...
Store and handle your Camcorder in a manner
that will not subject it to unnecessary movement
(avoid shaking and striking). Your Camcorder
contains a sensitive pick-up device which could
be damaged by improper handling or storage.
CARE
●TO CLEAN YOUR CAMCORDER ... Do
not use strong or abrasive detergents when
cleaning your Camcorder body.
●TO PROTECT THE LENS ... Do not touch
the surface of the lens with your hand. Use
a commercial Camcorder lens solution and
lens paper when cleaning the lens. Improper
cleaning can scratch the lens coating.
●TO PROTECT THE FINISH OF YOUR
CAMCORDER ... Before handling your
Camcorder, make sure your hands and face
are free from any chemical products, such as
suntan lotion, as it may damage the finish.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and
ask for the correct method of disposal.
- If you see this symbol -

6
You (“Licensee”) are granted a license for the Software defined in this End User Software Agreement
(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee
does not agree to the terms and conditions of this Agreement, promptly return the Software to
Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made
the purchase.
Article 1 License
Licensee is granted the right to use the software, including the information recorded or described on
the CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”),
but all applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not
transferred to Licensee.
Article 2 Use by a Third Party
Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to
use, copy or modify the Software, except as expressly provided for in this Agreement.
Article 3 Restrictions on Copying the Software
Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.
Article 4 Computer
Licensee may only use the Software on a single computer at a single location.
Article 5 Reverse Engineering, Decompiling or Disassembly
Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent either
of them is permitted under law or regulation of the country where Licensee resides. Matsushita, or its
distributors or dealers will not be responsible for any defects in the Software or damage to Licensee
caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.
Article 6 Limitation of Liability
The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including,
but not limited to, warranties of non-infringement, merchantability and/or fitness for a particular purpose.
Further, Matsushita does not warrant that the operation of the Software will be uninterrupted or error
free. Matsushita or any of its distributors or dealers will not be liable for any damage suffered by
Licensee arising from or in connection with Licensee’s use of the Software.
Article 7 Export Control
Licensee agrees not to export or re-export to any country the Software in any form without the
appropriate export licenses under regulations of the country where Licensee resides, if necessary.
Article 8 Termination of License
The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the
terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the
Software and related documentation together with all the copies thereof at Licensee’s own expense.
Before opening the CD-ROM package (PV-GS69 Only), please read the following.
End User License Agreement (for USB Driver, MotionDV STUDIO and
Quick Movie Magic)

7
This operating instruction book is designed for use with models PV-GS29, PV-GS39 and PV-GS69. The
PV-GS69 is the model used for illustrative purposes. Features may vary, so please read carefully.
Differences between models
Model Number PV-GS29 PV-GS39 PV-GS69
Battery Pack
(Supplied)
CGR-DU06
(640 mAh)
CGR-DU06
(640 mAh)
CGA-DU12
(1 150 mAh)
CD-ROM – – Supplied (LSFT0648)
USB Cable – Supplied (K1HA05CD0014) Supplied (K1HA05CD0014)
Card Feature No Yes Yes
Monitor 2.5-inch LCD 2.7-inch Wide LCD 2.7-inch Wide LCD
USB Jack* No Yes (Full-Speed) Yes (High-Speed)
Audio Dubbing No No Yes
Recording a Still
Picture on a Tape Yes No No
Cinema Function Yes No No
Wide/4:3 Function No Yes Yes
Remote Control
Sensor No No Yes
How to Turn off the Demo Mode
To terminate the demonstration mode, insert a cassette or set the [ DEMO MODE] to
[OFF] as follows.
1Set [ SETUP] >> [ DEMO MODE] >> [OFF].
* It is only compatible with USB 2.0 PCI Card and/or connection.

8
Before using the PC function (pp. 56~69), please refer to the OS (operating system) compatibility chart,
below.
With a PC (Operating System Compatibility Chart)
Model
Number Windows OS Built-in SD Drive Web Camera
MotionDV STUDIO/
Quick Movie Magic
PV-GS29
Windows 2000 – – –
Windows XP – – –
PV-GS39
Windows 2000 Yes* Yes (SP4 or later) –
Windows XP Yes* Yes (SP2 or later)* –
PV-GS69
Windows 2000 Yes* Yes (SP4 or later) Yes (SP4 or later)
Windows XP Yes* Yes (SP1 or later) Yes (SP2 or later)
Model
Number Macintosh OS Built-in SD Drive Web Camera
MotionDV STUDIO/
Quick Movie Magic
PV-GS29 X v 10.1 - v 10.4 – – –
PV-GS39 X v 10.1 - v 10.4 Yes* – –
PV-GS69 X v 10.1 - v 10.4 Yes* – –
* The USB equipment operates with the driver installed standard on your OS.
For Windows
For Macintosh
Model
Number Macintosh OS iMovie/iMovieHD
PV-GS29 X v 10.3 - v 10.4 Yes
PV-GS39 X v 10.3 - v 10.4 Yes
PV-GS69 X v 10.3 - v 10.4 Yes
For Macintosh (DV connection)

9
Contents
About Recording...................................................31
Recording on a Tape ............................................31
To Check the Recording.......................................32
Finding the End of Recording
(Blank Search Function) .....................................32
Recording a Still Picture on a Tape
(PV-GS29 Only)..................................................33
Recording a Still Picture on a Card (Photoshot)
(For PV-GS39/PV-GS69)....................................33
Recording Yourself ...............................................35
Recording with the Built-in LED Video Light.........35
Quick Start............................................................35
Self-timer Recording (For PV-GS39/PV-GS69)....36
Zoom In/Out Functions .........................................37
Digital Zoom Function...........................................37
Image Stabilizer Function .....................................38
Fade In/Out Functions ..........................................38
Backlight Compensation Function ........................39
MagicPix Function ................................................40
Soft-Skin Mode .....................................................40
Wind Noise Reduction Function ...........................41
Cinema Function (PV-GS29 Only) .......................41
Wide/4:3 Function (For PV-GS39/PV-GS69) .......41
Recording in Special Situations (Scene Mode) ....42
Recording in Natural Colors (White Balance).......43
Manual Shutter Speed Adjustment.......................45
Manual Iris Adjustment (F Number)......................45
Manual Focus Adjustment ....................................46
Playing Back a Tape.............................................47
Finding a Scene You Want to Play Back..............48
Slow Motion Playback (PV-GS69 Only) ...............48
Still Playback/Still Advance Playback...................49
Playing Back a Memory Card
(For PV-GS39/PV-GS69)....................................49
Slide Show (For PV-GS39/PV-GS69) ..................50
Deleting the Files Recorded on a Card
(For PV-GS39/PV-GS69)....................................51
Writing Printing Data on a Card (DPOF Setting)
(For PV-GS39/PV-GS69)....................................52
Protecting the Files on a Card (Lock Setting)
(For PV-GS39/PV-GS69)....................................52
Formatting a Card (For PV-GS39/PV-GS69) .......53
Playing Back on Your TV......................................53
Recording from a Tape onto a Card
(For PV-GS39/PV-GS69)....................................55
Audio Dubbing (PV-GS69 Only) ...........................55
Copying onto a DVD Recorder or a VCR
(Dubbing)............................................................56
Using the DV Cable for Recording
(Digital Dubbing).................................................56
PC Connection With DV Interface Cable..............57
Using Camcorder with a PC .................................58
Using the USB Function ......................................58
To disconnect USB cable safely...........................61
Using as a Web Camera ......................................62
Using the Motion Picture Editing Software
(PV-GS69 Only)..................................................66
If you no longer need software or driver
(Uninstall)............................................................69
Transferring Motion DV Tape Pictures
(Camcorder→Macintosh) via DV Cable
(iMovie / iMovie HD) ...........................................70
Notes ....................................................................70
Indications ............................................................73
Warning/Alarm Indications....................................74
Cautions for Use...................................................75
Before Requesting Service
(Problems and Solutions) ...................................78
Using the RESET button ......................................81
Explanation of Terms............................................82
Specifications .......................................................83
Camcorder Accessory System .............................84
Index.....................................................................85
Before Using
Things You Should Know .......................................2
Safety Precautions .................................................2
Precautions.............................................................5
End User License Agreement.................................6
Differences between models ..................................7
With a PC (Operating System Compatibility Chart)
................................................................................8
Quick Guide..........................................................10
Standard Accessories...........................................12
Parts Identification and Handling..........................12
The Remote Control (PV-GS69 Only : Optional)..14
Power Supply .......................................................15
Charging Time and Available Recording Time .....16
To Use as a Grip Belt ...........................................17
Re-attaching the Lens Cap...................................18
Attaching the Shoulder Strap................................18
Inserting/Removing a Cassette ............................18
Using a Memory Card (Optional)
(For PV-GS39/PV-GS69)....................................20
Turning on the Camcorder....................................21
Setting Date and Time..........................................21
Using the Viewfinder/LCD Monitor .......................22
Easy to Use Mode Dial .........................................23
How to Use the Joystick Control...........................23
Using the Menu Screen ........................................26
Selecting Language..............................................27
List of Menus ........................................................27
LP Mode ...............................................................30
Recording Mode
Playback Mode
Editing Mode
With a PC
Others

10
• Before use, fully charge the Battery.
• Since the Battery will not be charged when
the DC Cable is connected to the AC Adaptor,
disconnect it from the AC Adaptor.
• The [CHARGE] Lamp lights up, and charging
starts.
• When the [CHARGE] Lamp goes off, charging
is completed.
1Attach the Battery to the AC Adaptor and
charge it.
2Attach the charged Battery to the
Camcorder.
1Slide the [OPEN/EJECT] Lever 1toward
the front and pull up to fully open the
Cassette Compartment Cover.
• To protect the tape, if the cover is not fully
opened, the cassette holder cannot be ejected.
2After the Cassette Holder is opened, insert
a Cassette.
3Close the Cassette Holder by pressing the
[PUSH] mark 2.
4Only after the Cassette Holder is
completely housed, close the Cassette
Compartment Cover by pressing the mark
3.
2
1
Inserting a Card
2Open the Card Slot Cover 3.
3While holding the Memory Card with its
cut corner facing right 4insert it into the
Card Slot 5.
4Close the Card Slot Cover 3securely.
3
1Place your Thumb on the [OPEN] 1Knob
and pull the LCD Monitor 2out in the
direction of the arrow.
1
2
3
Quick Guide
Inserting a Cassette
Before using the Viewfinder, adjust the field of view
so that the displays inside the Viewfinder become
clear and easy to read.
1Pull the Viewfinder.
Using the Viewfinder
Using the Battery
4
5
Turning on the Camcorder
How to Turn on the Power
1Set the [OFF/ON] Switch to [ON] while
pressing the button 1.
• The [STATUS] Indicator lights Red.
How to Turn off the Power
2Set the [OFF/ON] Switch to [OFF] while
pressing the button 1.
• The [STATUS] Indicator goes off.
1
1
• Open the LCD Monitor or extend the Viewfinder
before turning on the power.

11
Before Using
(PV-GS39/
PV-GS69)
(PV-GS29)
Recording on a Tape
1Set the Mode Dial to Tape Recording
Mode.
• The [ TAPE RECORDING MODE] is
displayed on the screen.
2Press the Recording Start/Stop Button.
• Recording starts.
1Set the Mode Dial to Card Recording
Mode.
• The [ CARD RECORDING MODE] is
displayed on the screen.
2Press the [PHOTO SHOT] Button.
Recording a Still Picture on Card
(Photoshot)
(For PV-GS39/PV-GS69)
1Set the Mode Dial to Tape Playback Mode.
• The [ TAPE PLAYBACK MODE] is displayed
on the screen.
• The One-Touch Navigation icon is displayed
on the lower right of the screen.
2Move the Joystick Control [◄] 1to rewind
the tape.
3Move the Joystick Control [▲] 2to start
playback.
4Move the Joystick Control [▼] 3to stop
playback.
Playing Back a Tape
1Set the Mode Dial to Picture Playback
Mode.
• The [ CARD PLAYBACK MODE] is
displayed on the screen.
• The One-Touch Navigation icon is displayed
on the lower right of the screen.
Joystick Control [▲] : Starting the Slide Show
Stop the Slide Show
Joystick Control [▼] : Erase the pictures
Joystick Control [◄] : Playing back the previous
picture
Joystick Control [►] : Playing back the next picture
2Start Playback.
Playing Back a Card
(For PV-GS39/PV-GS69)
3Press the Recording Start/Stop Button
again to pause the recording.
2Adjust by turning the Eyepiece Corrector
Knob 1.
1
[One-Touch Navigation icon]
1
2
3
[One-Touch Navigation icon]
(PV-GS39/
PV-GS69)
(PV-GS29)

12
A/V
13
10
11
12
14
15
Standard Accessories
The following accessories are supplied with your
Camcorder.
1) AC Adaptor, DC Cable and AC Cable
(pp. 15~16)
1)
2) 3)
4) 5)
K2GJ2DC00011
K2KC4CB00020
LSFC0018 K1HA05CD0014
(For PV-GS39/
PV-GS69)
2) Battery Pack (p. 16)
3) AV Cable (pp. 53, 56)
4) Shoulder Strap (p. 18)
5) USB Cable and CD-ROM
(pp. 58, 60~61, 63, 69)
CAUTION:
This unit will operate on 110/120/220/240 V
AC. An AC plug adaptor may be required
for voltages other than 120 V AC. Please
contact either a local or foreign electrical
parts distributor for assistance in selecting an
alternate AC plug.
We recommend using the accessory power
plug adaptor (VJSS0070/KZDB4ZE00001) in
an area which has special AC outlets.
Parts Identification and Handling
Camcorder
1LCD Monitor Open Knob [OPEN] (p. 22)
2LCD Monitor (pp. 21~23, 78)
Due to limitations in LCD production technology,
there may be some tiny bright or dark spots on the
LCD Monitor screen.
However, this is not a malfunction and does not
affect the recorded picture.
3Card Access Lamp (p. 20)
4Reset Button [RESET] (pp. 79, 81)
5DC Input Jack [DC IN] (p. 16)
6Battery Holder (p. 16)
7Mode Selector Switch
[AUTO/MANUAL/FOCUS] (pp. 31, 42~46)
8Card Slot Cover (p. 20)
9Card Slot (p. 20)
10 Lens Hood (p. 78)
11 Lens
12 White Balance Sensor (p. 44)
Remote Control Sensor (PV-GS69 Only)
(p. 15)
1
2
3
5
8
7
9
PV-DAC14D K2CA2CA00025
Before Using
LSFT0648
(PV-GS69 Only)
6
4
CGA-DU12
(PV-GS69
Only)
CGR-DU06
(For PV-GS29/
PV-GS39)

13
Before Using
Due to limitations in LCD production technology,
there may be some tiny bright or dark spots on the
Viewfinder screen.
However, this is not a malfunction and does not
affect the recorded picture.
22
19
17
20
18
16 Cassette Eject Lever [OPEN/EJECT]
(p. 18)
17 Cassette Holder (pp. 18~19)
18 Cassette Compartment Cover (pp. 18~19)
19 DV Input/Output Terminal
(pp. 56~57, 69~70)
• Connect this to the digital video equipment.
20 USB Jack [ ] (For PV-GS39/PV-GS69)
(pp. 60~61, 63, 69)
21 Speaker (p. 47)
22 Built-in LED Light (p. 35)
23 Viewfinder (pp. 21~23, 78)
24 Eyepiece Corrector Knob (p. 22)
25 Photoshot Button [PHOTO SHOT]
(pp. 33, 34)
26 Shoulder Strap Holders (p. 18)
27 Power Switch [OFF/ON] (p. 21)
28 Status Indicator [STATUS] (pp. 21, 36)
29 Menu Button [MENU] (p. 26)
30 Mode Dial (p. 23)
31 Recording Start/Stop Button (p. 31)
32 Joystick Control (pp. 23, 26)
33 Light Button [LIGHT] (p. 35)
34 Grip Belt (p. 17)
35 Tripod Receptacle
• This is a hole for attaching the Camcorder
to optional tripod. (Please carefully read the
Operating Instructions for how to attach the
tripod to the Camcorder.)
• You cannot open the Card Slot Cover when
the tripod is used. Insert the card first and
then attach the tripod.
36 Battery Eject Switch
[BATTERY RELEASE] (p. 16)
36
34
35
24 25
26
27
29
33
30
23
31
21
13 Zoom Lever [W/T] (pp. 37, 49)
Volume Lever [– / VOL +] (pp. 47, 50)
14 Microphone (built-in, stereo) (pp. 37, 41)
15 Audio-Video Output Jack [AV OUT]
(pp. 53, 56)
• Connecting an AV Cable to this jack activates
the Camcorder’s built-in speaker.
• When connecting the pin plug of the AV
Cable to this jack, plug it in as far as it goes.
16
28 32

14
* means that these buttons function in the same
manner as the corresponding buttons on the
Camcorder.
46
47
48
49
50
51
52
53
The Remote Control
(PV-GS69 Only : Optional)
Before using the Remote Control, insert a
button-type battery (not supplied).
1While pressing the Lock Button 1, pull out
the Battery Holder.
2Insert a button-type battery (CR2025) with
the (+) marking facing upward.
1
Inserting the Button-type Battery
42
43
44
45
42
Slow Motion/Still Advance Buttons [◄Ι, Ι►]
(◄Ι: reverse, Ι►: forward) (pp. 48~49)
43 Zoom/Volume Button [ZOOM/VOL]*
(pp. 37, 47)
44 Variable Speed Search Button
[VER SEARCH] (p. 48)
45 Menu Button [MENU]* (p. 27)
46 Photoshot Button [PHOTO SHOT]*
(pp. 33~34)
47 Rewind/Review Button [◄◄ ] (p. 48)
48 Pause Button [ ] (pp. 49, 55, 57)
49 Stop Button [■] (pp. 15, 57)
50 Recording Start/Stop Button
[START/STOP]* (p. 31)
51 Play Button [►] (pp. 48~49, 57)
52 Fast Forward/Cue Button [►► ] (p. 48)
53 Enter Button [ENTER] (p. 27)
Remote Control
(PV-GS69 Only : Optional)
Using the Remote Control with the Camcorder, most
of the Camcorder functions can be operated from a
distance.
37
38
41
39
40
37 Indication Output Button [EXT DISPLAY]
(pp. 54, 56)
38 Date/Time Button [DATE/TIME] (p. 29)
39 Audio Dubbing Button [AUDIO DUB]
(p. 55)
40 Recording Button [●REC] (p. 57)
41 Cursor buttons for Variable Speed Search
Function [▲, ▼] (p. 48)
Select Button [▲▼◄►] (p. 27)

15
Before Using
3Insert the Battery Holder into the Remote
Control.
• When the button-type battery is exhausted, replace
it with a new CR2025 battery. (A battery is normally
expected to last about 1 year. However, it depends
on operation frequency.)
• Make sure to match the poles correctly when
inserting the button-type battery.
●Use Battery with Panasonic type CR2025
only. Use of another battery may present a
risk of fire or explosion.
●Battery may explode if mistreated.
●As with any small object, this type of
Battery can be swallowed by young
children. Do not allow children to handle
this Battery.
●Dispose of used battery promptly.
●Do not recharge, disassemble or dispose
of in fire.
WARNING
CAUTION
Using the Remote Control
(PV-GS69 Only : Optional)
• Distance from the Camcorder: Within
approximately 15 feet (5 meters)
• Angle: Within approximately 15° in the vertical
and horizontal directions from the central axis
1Direct the Remote Control at the Remote
Control Sensor of the Camcorder and
press an appropriate button.
• The above operating ranges are for indoor use.
Outdoors or under strong light, the Camcorder may
not operate properly even within the above ranges.
15°
15°
15°
15°
[VCR1]:
Press the [Ι►] Button and [ ■] Button
simultaneously. 1
[VCR2]:
Press the [◄Ι] Button and [ ■] Button
simultaneously. 2
• When the battery in the Remote Control is
replaced, the mode is automatically reset to [VCR1]
Mode.
Selecting Remote Control Modes
When 2 Camcorders are used simultaneously,
they can be operated individually by selecting
different Remote Control Modes.
• If the Remote Control Mode of the Camcorder
and that of the Remote Control do not match
with each other, [REMOTE] will appear. When
the Remote Control is operated for the first
time after the Camcorder is turned on, [CHECK
REMOTE MODE] (p. 74) will appear and
operation is impossible. Set the same Remote
Control Mode.
Setup on the Camcorder
Set [ REMOTE] on the [ SETUP] Sub-Menu to
the desired Remote Control Mode. (pp. 27~29)
Setup on the Remote Control
12
Power Supply
Using the AC Adaptor
• Before connecting or disconnecting the
power supply, set the [OFF/ON] Switch on
the Camcorder to [OFF] and make sure that
[STATUS] Indicator is not lit. (p. 21)

16
1Connect the DC Cable to the Camcorder.
2Connect the DC Cable to the AC Adaptor.
3Connect the AC Cable to the AC Adaptor
and the AC Jack.
Using the Battery
• We recommend using a Panasonic Battery.
• We cannot guarantee the quality of this Camcorder
when batteries from other companies are used.
1Attach the Battery to the AC Adaptor and
charge it.
2Put the Battery on the Battery Mount by
aligning the mark, and then securely plug
it in.
Before use, fully charge the Battery.
1
2
3
Charging Time and Available
Recording Time
Supplied battery
(PV-GS29)
CGR-DU06
(7.2 V / 640 mAh)
A1 h 40 min.
B1 h 50 min. (1 h 25 min.)
C55 min. (45 min.)
Supplied battery
(PV-GS39)
CGR-DU06
(7.2 V / 640 mAh)
A1 h 40 min.
B1 h 45 min. (1 h 20 min.)
C55 min. (40 min.)
Supplied battery
(PV-GS69)
CGA-DU12
(7.2 V / 1 150 mAh)
A2 h 25 min.
B3 h 10 min. (2 h 30 min.)
C1 h 35 min. (1 h 15 min.)
Notes:
• When the Camcorder has been used for a long
time, the Camera body becomes warm, but this is
not a malfunction.
• If the [CHARGE] Lamp does not light up although
the Battery is attached to the AC Adaptor, detach
the Battery and reattach it.
• Since the Battery will not be charged when
the DC Cable is connected to the AC Adaptor,
disconnect it from the AC Adaptor.
• The [CHARGE] Lamp lights up, and charging
starts.
• When the [CHARGE] Lamp goes off, charging
is completed.
• When the battery is completely discharged, the
[CHARGE] Lamp blinks at first, but the battery
is charged normally. When the temperature of
the battery is too high or low, the [CHARGE]
Lamp blinks and the charging time becomes
longer than usual.
3Attach the charged Battery to the
Camcorder.
Disconnecting the Power Source
Set the [OFF/ON] Switch to [OFF], and while
sliding the [BATTERY RELEASE] Switch, remove
the Battery downward or DC Cable.
• When attaching or removing Battery, set the
[OFF/ON] Switch to [OFF] and make sure the
[STATUS] Indicator is not lit.
• Hold down the battery with your hand so it
does not fall.

17
Before Using
ACharging Time
Maximum Continuous Recording Time
Intermittent Recordable Time
B
(The intermittent recordable time refers to recordable
time when the recording and stopping operations are
repeated.)
C
Optional battery
(PV-GS69)
CGR-DU06
(7.2 V / 640 mAh)
A1 h 40 min.
B1 h 45 min. (1 h 20 min.)
C55 min. (40 min.)
Optional battery
(PV-GS29)
CGA-DU12
(7.2 V / 1 150 mAh)
A2 h 25 min.
B3 h 15 min. (2 h 40 min.)
C1 h 40 min. (1 h 20 min.)
Optional battery
(PV-GS39)
CGA-DU12
(7.2 V / 1 150 mAh)
A2 h 25 min.
B3 h 10 min. (2 h 30 min.)
C1 h 35 min. (1 h 15 min.)
Optional battery
(PV-GS29)
CGA-DU21
(7.2 V / 2 040 mAh)
A3 h 55 min.
B5 h 45 min. (4 h 30 min.)
C2 h 55 min. (2 h 15 min.)
Optional battery
(PV-GS39/PV-GS69)
CGA-DU21
(7.2 V / 2 040 mAh)
A3 h 55 min.
B5 h 30 min. (4 h 15 min.)
C2 h 45 min. (2 h 10 min.)
• “1 h 40 min.” indicates 1 hour and 40 minutes.
• Battery CGR-DU06 (PV-GS29/PV-GS39) or
CGA-DU12 (PV-GS69) is supplied.
• The times shown in the table are approximate
times. The numbers indicate the recording time
when the Viewfinder is used. The numbers in
parentheses indicate the recording time when the
LCD Monitor is used. In actual use, the available
recording time may be shorter.
• The times shown in the table are for continuous
recording at a temperature of 25 °C (77 °F) and
humidity of 60 %. If the Battery is charged at a
higher or lower temperature, the charging time may
be longer.
• We recommend the Battery Pack CGA-DU12 and
CGA-DU21 for long time recording (2 hours or
more for continuous recording, 1 hour or more for
intermittent recording.)
• The available recording time becomes shorter
if you use both of Viewfinder and LCD Monitor
simultaneously when rotating the LCD Monitor
forward to record yourself.
• The batteries heat up after use or charging. The
Camcorder being used will also heat up. This is
normal.
• Along with the reduction of the battery capacity,
the display will change: →→→
→. If the battery discharges, then
() will flash.
To Use as a Grip Belt
Adjust the length of the Grip Belt to the size of your
hand.
1Detach the end of the Grip Belt.
2Adjust the length of the Grip Belt to the
size of your hand.
3Reattach the Grip Belt.

18
Re-attaching the Lens Cap
To protect the Lens surface, attach the Lens Cap.
• The Lens Cap and Lens Cap Cord come
preattached to the Grip Belt.
1Pass one end of the Lens Cap Cord
through the attached eye on the Lens Cap.
Then pass the Lens Cap through the loop
made by itself and pull tight. 2Fold the end of the Shoulder Strap, run
it through the Shoulder Strap Length
Adjuster, and pull it.
• Pull it out more than 1 inch (2 cm) 1from
the Shoulder Strap Length Adjuster so that it
cannot slip off.
• Attach the other end of the Shoulder Strap to
the other Shoulder Strap Holder in the same
way.
Inserting/Removing a Cassette
1
• Please use Genuine Panasonic DVC Tapes for
more information please contact your local dealer
or visit www.panasonic.com.
• For your reference if you travel frequently you
should also purchase a Panasonic head cleaning
tape AY-DVMCLA and use when HEAD CLOG
message appears on the LCD/EVF of your
Camcorder.
1Fit the AC Adaptor or the Battery and turn
on the Power.
2Slide the [OPEN/EJECT] Lever toward the
front and pull up to fully open the Cassette
Compartment Cover.
• To protect the tape, if the cover is not fully
opened, the cassette holder cannot be ejected.
• When not using the Lens Cap, pull the Lens Cap
Cord in the direction of the arrow. 1
• When you are not recording, be sure to cover the
Lens with the Lens Cap for protection. 2
Attaching the Shoulder Strap
We recommend that you attach the Shoulder Strap
before going out to avoid dropping the Camcorder.
1Pull the end of the Shoulder Strap
through the Shoulder Strap Holder on the
Camcorder.
2
1
• When you remove the Lens Cap, press the knobs
firmly.

19
Before Using
3After the Cassette Holder is opened,
insert/remove a Cassette.
4Close the Cassette Holder by pressing the
[PUSH] mark 1.
• The Cassette Holder is housed.
1
• When inserting a cassette, orient it as shown in
the above, and then securely insert it as far as
it goes.
• When removing, pull it straight out.
5Only after the Cassette Holder is
completely housed, close the Cassette
Compartment Cover by pressing the mark
3.
3
2
Caution :
Before closing the Cassette Holder 2, be sure
your fingers have not been placed underneath the
Cassette Holder as shown below. This may cause
your fingers to jam in the cassette holder.
[Bottom View]Do not place fingers here.
When the Cassette Holder does not
come out
• Close the Cassette Compartment Cover
completely, and then open it again completely.
• Check if the battery has run down.
• Check if the Cassette Compartment Cover is in
contact with grip belt as shown below. If so, be
sure the grip belt stays clear of the cover when
opening.
When the Cassette Holder cannot be
housed
• Set the [OFF/ON] Switch to [OFF], then to [ON]
again.
• Check if the battery has run down.
Notes:
• After use, be sure to rewind the cassette
completely, remove it and put it in a case. Store the
case in an upright position. (p. 77)
• If the indicator of the condensation does not
display on the LCD screen and/or Viewfinder and
you notice condensation on the lens or the main
unit, do not open the cassette cover otherwise
condensation may be formed on the heads or the
cassette tape. (p. 76)
• When inserting a previously recorded Cassette,
use the Blank Search Function (p. 32) to find the
position where you want to continue recording.
If you overwrite-record on a previously recorded
cassette, be sure to find the position where you
want to continue recording.
• If a new Cassette is inserted, rewind to the
beginning of the tape before starting recording.
• When inserting the cassette, make sure it faces in
the right direction and then push it in until it stops.
• When the Cassette Holder is in action, do not touch
anything except the [PUSH] mark.
• Close the Cassette Compartment Cover tightly.
• When closing the Cassette Compartment Cover,
do not get anything, such as a cable, caught in the
cover.

20
1Turn off the Power.
2Open the LCD Monitor and then open the
Card Slot Cover.
Inserting/Removing a Card
Using a Memory Card (Optional)
(For PV-GS39/PV-GS69)
A Card can be used to record still pictures.
• Use a genuine SD Memory Card manufactured by
Panasonic only.
Before inserting or removing a Card, be sure to
turn off the Camcorder.
• Otherwise, the Camcorder may not function
properly or it may cause the loss of recorded data
in a Card.
Accidental Erasure Prevention
1
Opening the accidental erasure prevention slider
1on the cassette (by sliding it to the [SAVE] arrow
direction) prevents recording. To enable recording,
close the accidental erasure prevention slider (by
sliding it to the [REC] arrow direction).
While the Camcorder is accessing the Card (reading,
recording, playback or erasing), the Card Access
Lamp lights up.
• While the Card Access Lamp is on, never attempt
to open the Card Slot Cover, to pull out the Card,
to turn off the Camcorder, or to turn the Mode Dial.
Such actions will damage the Card, and recorded
data, and cause the Camcorder to malfunction.
Card Access Lamp
Concerning the Card
• Do not touch the terminals on the back of the
card.
• Do not format the card with another Camcorder
or any personal computer. This operation may
make the card unusable.
• Electrical noise, static electricity, or failure of the
Camcorder or the card may damage or erase
the data stored on the card. We recommend
saving important data on a personal computer by
using a USB Cable, PC Card Adaptor, and USB
Reader/Writer.
SD Memory Card
• The memory capacity indicated on the SD
Memory Card label corresponds to the total
amount of capacity to protect and manage
the copyright and the capacity available as
conventional memory for a Camcorder, personal
computer or other equipment.
3While holding the Memory Card with its
cut corner facing right 1, insert/remove it
into/from the Card Slot.
4Close the Card Slot Cover securely.
Removing the Card
Open the Card Slot Cover and press the center of
the Card and then pull it straight out.
• After removing the Card, close the Card Slot
Cover.
• The Camcorder may be damaged if the Card is
forced out when the Card is fully inserted.
1
Concerning the Write Protection
Switch on the SD Memory Card
The SD Memory Card has a write protection
switch on it. If the switch is moved to [LOCK], you
cannot write to the card, erase the data on it, or
format it. If it is moved back, you can.