Panasonic CQ-D5501W User manual

General
Power Supply DC 12V (11V - 16V),
Test Voltage 14.4V
Negative Ground
Current Consumption Less than 2.3A (CD mode ; 0.5W
4-channels)
Maximum Power Output 50W×4 (at 1kHz)
volume control maximum
Video Signal system NTSC/PAL 1.0 Vp-p 75Ω
RCA pin jack
Tone/SQ Adjustment Range SQ Low/Bass ; ±12dB
(at 60Hz, 80Hz, 100Hz, 200Hz)
SQ Mid ; ±12dB
(at 500Hz, 1kHz, 2kHz, 3kHz)
SQ High/Treble ; ±12dB
(at 10kHz, 12kHz, 15kHz, 18kHz)
Speaker Impedance 4-8Ω
Pre-Amp Output Voltage 2V (CD mode; 1kHz, 0dB)
Pre-Amp Output Impedance 200Ω
Subwoofer Output Voltage 2V
Subwoofer Output Impedance 200Ω
FM Stereo Radio
Frequency Range 87.5MHz - 108.0MHz
Usable Sensitivity 6dB/µV (S/N 30dB)
Frequency Response 30Hz-15kHz (±3dB)
Alternate Channel Selectivity 75dB
Stereo Separation 35dB (1kHz)
Image Rejection Ratio 70dB
© 2005 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
CQ-D5501W
DVD Player/Receiver with CD Changer
Control
IF Rejection Ratio 100dB
Signal to Noise Ratio 62dB
AM Radio
Frequency Range 531 - 1,602kHz
Usable Sensitivity 28dB/µV (S/N 20dB)
Disc Player
DA Converter 1bit DAC System
Pick-Up Type Astigma 3-beam
Light Source Semiconductor Laser
Frequency Response 20Hz to 20,000Hz (CD)
20Hz to 22,000Hz
(DVD video 48kHz sampling)
20Hz to 44,000Hz
(DVD video 96kHz sampling)
Signal to Noise Ratio 96dB (IHF, A)
Wow and Flutter Below measurable limits
Dimensions** (W×H×D) 178×50×160mm
Weight** 1.8kg
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
• • •
• Above specifications comply with EIA standards.
AUTOMOTIVE AFTERMARKET
Specifications*
ORDER NO.ACED050317C3

1 ABOUT LEAD FREE SOLDER (PbF) 3
2 LASER PRODUCTS 3
3 FEATUERS 3
4 REPLACING THE FUSE 3
5 MAINTENANCE 3
6 NOTES 3
7 DIMENSIONS 3
8 WIRING CONNECTION 4
9 DISASSEMBLY INSTRUCTIONS 5
10 TERMINALS DESCRIPTION 8
11 PACKAGE AND IC BLOCK DIAGRAM 13
12 REPLACEMENT PARTS LIST 17
13 EXPLODED VIEW (Unit) 22
14 DVD PLAYER PARTS LIST 23
15 EXPLODED VIEW (CD Deck) 27
16 WIRING DIAGRAM 28
17 SCHEMATIC DIAGRAM 33
18 BLOCK DIAGRAM 39
CONTENTS
Page Page
2
CQ-D5501W

1 ABOUT LEAD FREE
SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
Caution :
• • •
• Pb free solder has a higher melting point than standard
solder; Typically the melting point is 50 - 70°F (30 -
40°C) higher. Please use a soldering iron with
temperature control and adjust it to 700 ± 20°F (370 ±
10°C). In case of using high temperature soldering iron,
please be careful not to heat too long.
• • •
• Pb free solder will tend to splash when heated too high
(about 1100°F/600°C)
• • •
• This lead free solder will be used for the products after
serial No. 1,000,001.
2 LASER PRODUCTS
3 FEATUERS
• • •
• Digital servo for reliable playback.
• • •
• PLL (Phase Locked Loop) synthesized tuning.
• • •
• 18-FM, 6-AM presets with preset scan.
• • •
• DVD video, Video CD Playback.
• • •
• MP3 Playback from CD-R/RW.
• • •
• DVD-R, DVD-RW Playback.
• • •
• Fully Motorized Face Plate.
• • •
• Removable face plate.
• • •
• CD Changer Control.
• • •
• Digital Audio Output.
4 REPLACING THE FUSE
Use fuses of the same specified rating (15amps). Using
different substitutes or fuses with higher ratings, or connecting
the product directly without a fuse, could cause fire or damage
to the stereo unit.
5 MAINTENANCE
Your product is designed and manufactured to ensure a
minimum of maintenance. Use a dry, a soft cloth for routine
exterior cleaning. Never use benzine, thinner or other solvents.
6 NOTES
[RADIO BLOCK]
Do not align the AM/FM package block. When the package
block is necessary, it will be supplied already aligned at the
factory.
[CD DECK BLOCK]
This model has no servo alignment points because
microcomputer controls the servo circuit.
7 DIMENSIONS
3
CQ-D5501W

8 WIRING CONNECTION
4
CQ-D5501W

9 DISASSEMBLY INSTRUCTIONS
9.1. How to remove the Flexible PCB
5
CQ-D5501W

9.2. How to install the Main P.C.B of the Electric Slide Display
6
CQ-D5501W

7
CQ-D5501W

10.1. Main Block
IC601 : YESAM301
Pin
No. Port Description I/O Volt (V)
FM AM DVD CD
1 ACC ACC detection I 4.9 4.9 4.9 4.9
2AIN SPE.ANA A.IN I 0 0 0 0
3 NC - - - - - -
4 AVss GND - 4.9 0 0 0
5 SCL Electronic VOL clock O 4.9 4.9 4.9 4.9
6 SDA Electronic VOL data I/O 4.9 4.9 4.9 4.9
7 AVREF Reference voltage
for D/A converter I 4.8 4.8 4.8 4.9
8 LCD DO LCD data I 4.8 4.8 4.8 4.9
9 LCD DI LCD data O 4.8 2.8 4.8 4.9
10 LCD CLK LCD clock O 4.8 4.8 4.8 4.8
11 CDC DATA CD Changer data I 0 0 0 0
12 XM-RX XM Receiver RX
data I 4.9 4.9 4.9 4.9
13 CDC CLK CD Changer clock I 0 0 0 0
14 CDC REM
OUT Remote control data for CD Changer O 4.9 4.9 4.9 4.9
15 BZ-OUT Buzzer output O 0 0 0 0
16 DATA DVD Data I 0 0 4.7 4.9
17 AF MUTE AF MUTE control O 4.9 4.9 4.9 4.9
18 DCLK DVD clock transmit O 0 0 4.4 4.8
19 REQUEST Sub Wake-up
request O 0 0 4.9 4.9
20 NRESET DVD deck reset
output O 0 0 4.9 4.9
21 DCONT DECK power supply
control output O 0 0 0 0
22 RESW Deck mechanism
switch I 0 0 4.7 0
23 MSW1 Deck mechanism
switch I 0 0 0 0
24 MSW2 Deck mechanism
switch I 0 0 0 0
25 SSTOP Deck SSTOP I 0 0 0 0
26 LOEJ1 Load/Eject signal O 0 0 0 0
27 LOEJ2 Load/Eject signal O 0 0 1.6 1.6
28 CLOSE CLOSE signal O 0 0 4.8 5.1
29 MAIN
CONT MAIN power supply control O 4.8 4.8 4.8 4.8
30 DC DC
CNT DC/DC converter control O 0 0 4.8 4.8
31 AMP
CONT External AMP control O 4.8 4.8 4.8 4.8
32 ANT CONT Motor antenna
control O 4.8 4.8 0 4.8
33 Vss1 GND - 0 0 0 4.8
34 EXT MUTE TEL/NAVI MUTE
input I 4.9 4.9 4.9 0
35 PBK Parking brake signal I 0 0 0 0
36 VIDEO
CNT Video control signal O 0 0 4.8 4.8
37 OFFSET
DET PWR-IC offset detection I 4.9 4.9 4.9 4.9
38 AMP
MUTE PWR-IC MUTE control output O 4.9 4.9 4.9 4.9
39 STBY PWR-IC STBY
control output O 4.9 4.9 4.9 4.9
40 FP
MOTOR1 Front open/close control 1 O 0 0 0 0
41 FP
MOTOR2 Front open/close control 2 O 0 0 0 0
42 V CNT1 Panel driving voltage
control 1 O 4.9 4.9 4.9 4.9
Pin
No. Port Description I/O Volt (V)
FM AM DVD CD
43 S LED Security LED control
output O 0 0 0 0
44 PANEL IN PANEL detect I 4.9 4.9 4.9 4.9
45 INV CONT INV power supply
control O 4.8 4.8 4.8 4.8
46 LCD CE LCD chip enable O 0 0 0 0
47 LCD5V
CNT LCD 5V power switch O 0 0 0 0
48 EEPROM
CE (NC) No Connection - - - - -
49 EEPROM
SK (NC) No Connection - 0 0 0 0
50 EEPROM
DI (NC) No Connection - 0 0 0 0
51 EEPROM
DO (NC) No Connection - - - - -
52 Rotary 1 Rotary Encoder 1 I 4.8 4.8 0 4.8
53 Rotary 2 Rotary Encoder 2 I 4.8 4.8 0 4.8
54 PANEL
OPEN PANEL OPEN detection I 0 0 0 0
55 PANEL
CLOSE PANEL CLOSE detection I 4.9 4.9 4.9 4.9
56 PLL DO
(MI) PLL data input I 4.9 4.9 4.9 4.9
57 PLL CLK PLL clock output O 4.9 4.9 4.9 4.9
58 PLL DI
(MO) PLL data output O 0 0 0 0
59 PLL CE PLL chip enable
output O 0 0 0 0
60 RESET Reset input I 4.8 4.8 4.8 4.8
61 RDS CLK
(NC) RDS Clock I 0 0 4.8 0
62 RDS DATA
(NC) RDS Data I 0 0 0 0
63 REMO
DATA Main wake-up request I 4.7 4.7 0 -
64 BATT BATT detection I 4.5 4.5 4.7 4.7
65 CDC STB Changer storobe
signal input I 4.8 4.8 4.5 4.5
66 SA CLK Spectrum analizer
clock O 4.8 4.8 4.8 4.8
67 Vss0 GND I 0 0 0 0
68 Vdd1 Power supply I 4.9 4.9 4.9 4.9
69 X2 Crystal oscillator - 2.9 2.8 2.9 2.7
70 X1 Crystal oscillator - 2.8 2.3 2.3 2.2
71 TEST No Connection - - - - -
72 XT2 Crystal oscillator - 2.7 2.8 2.8 2.7
73 XT1 Crystal oscillator - 2.5 2.5 2.5 2.5
74 Vdd0 Power supply I 4.9 4.9 4.9 4.9
75 Avdd Power supply of D/A
converter I 4.9 4.9 4.9 4.9
76 INIT A Initializ A I 4.9 4.9 4.9 4.9
77 INIT B Initializ B I 4.9 4.9 4.9 4.7
78 ST FM ST detection I 4.8 4.8 4.8 4.8
79 SD FM/AM signal
strength I 0 0 0 0.5
80 NC - - - - - -
10 TERMINALS DESCRIPTION
8
CQ-D5501W

10.2. Display Block
IC901 : YESAM168
Pin No. Port Description I/O (V)
1-35 SEG3-37 LCD segment data O 2.5
36-51 SEG40-55 LCD segment data O 2.5
52-55 COM1-4 LCD common O 2.5
56,57 SEG39,38 Not used - -
58-61 KS3-6 Key scan O 5.0
62-66 Kl1-5 Key data I 0
67 VDD +5V power supply - 5.0
68 VLCD VLCD terminal - 4.8
69 VLCD1 VLCD1 terminal - 3.3
70 VLCD2 VLCD2 terminal - 1.7
71 VSS Ground - 0
72 TEST (Connecting to ground) - 0
73 OSC Oscillator terminal - 3.9
74 RESET Reset I 4.8
75 DO Key data output O 5.0
76 CE LCD driver chip enable I 0
77 CLK LCD clock I 4.9
78 DI LCD data I 4.9
79,80 SEG1,2 LCD segment data O 2.5
10.3. DVD Servo Block
IC202 : YESAM300
Pin
No. Name Description I/O (V)
1EXINT0 Interrupt 0 O 5
2EXINT1 Interrupt 1 O 5
3EXTCNT 0 Close signal I 3.3
4 VDD3 Power supply (3.3V) - 3.3
5 VSS Ground - 0
6 EXCNT 1 - - -
7 NSPCCS - - -
8 FADR17 Address 17 I 0
9 FADR18 Address 6 I 3.3
10 FADR11 Address 11 I 0.9
11 FADR9 Address 9 I 4.2
12 VDD15 Power supply (1.5V) - 1.5
13 FADR8 Address 8 I 4.5
14 FADR13 Address 13 I 4.3
15 FADR14 Address 14 I 0.3
16 NWE Write signal O 5
17 FADR16 Address 16 I 0
18 FADR15 Address 15 I 0.8
19 DRAM VDD15 Power supply (1.5V for DRAM) - 1.5
20 DRAMVSS (Connecting to ground) - 0
21 VSS Ground - 0
22 FADR12 Address 12 I 0.4
23 FADR7 Address 7 I 4.7
24 FADR6 Address 6 I 4.7
25 FADR5 Address 5 I 3.2
26 FADR4 Address 4 I 3.2
27 FADR3 Address 3 I 2.7
28 FADR2 Address 2 I 2.9
29 FADR1 Address 1 I 2.8
30 FADR0 Address 0 I 2.5
31 VSS Ground - 0
32 VDD3 Power supply (3.3V) - 3.3
33 FDT0 Data 0 I/O 2.8
34 FDT1 Data 1 I/O 2.6
35 FDT2 Data 2 I/O 2.6
36 FDT3 Data 3 I/O 2
Pin
No. Name Description I/O (V)
37 FDT4 Data 4 I/O 2.8
38 FDT5 Data 5 I/O 2.5
39 FDT6 Data 6 I/O 2.8
40 FDT7 Data 7 I/O 3.9
41 NCE Chip Enable O 0
42 FADR10 Address 10 I 0.5
43 NOE Output Enable O 0
44 MMOD (Connecting to ground) I 0
45 NRST Reset I 3.9
46 VSS Ground - 0
47 SCLK (NC) - - -
48 SDATA (NC) - - -
49 MDATA (NC) - - -
50 MCLOCK (NC) - - -
51 VDD3 Power supply (3.3V) - 3.3
52 OSCI Crystal oscillator I -
53 OSCO Crystal oscillator O 1.7
54 VSS Ground - 0
55 DRV0 Loading motor drive O 1.6
56 DRV1 Lpindle motor drive O 1.4
57 DRV2 FBAL signal O 1.2
58 DRV3 (NC) - - -
59 DRV4 Motor driver mute 2 O 0
60 DRV5 SSTOP signal O 0
61 DRV6 DVD switch O 0
62 DRV7 Motor driver mute 1 O 3.3
63 VSS Ground - 0
64 DRV8 (NC) - - -
65 DRV9 (NC) - - -
66 DRV10 (NC) - - -
67 DRVE11 (NC) - - -
68 DRV12 SCK (for RF Amp) O 0
69 DRV13 STDIO (for RF Amp) O 0
70 DRV14 SEN signal (for RF Amp) O 3.3
71 DRAMVSS (Connecting to ground) - 0
72 DRAM VDD15 Power supply (1.5V for DRAM) - 1.5
73 DRAM VDD33 Power supply (3.3V for DRAM) - 3.3
74 VDD3 Power supply (3.3V) - 3.3
75 FG Motor FG input I 2.6
76 TX (NC) - - -
77 VDD15 Power supply (1.5V) - 1.5
78 VSS Ground - 0
79 TSTSG (NC) - - -
80 VFOSHORT
(NC) - - -
81 JLINE J-LINE setup output O 1.8
82 BDO Drop-out signal input I 0
83 OFTR Off-track signal input I 0
84 AVSS0 Ground - 0
85 ROUT (NC) - - -
86 LOUT (NC) - - -
87 AVDD Power supply (3.3V) - 3.3
88 VCOF JFVCO Control voltage I 0
89 TRCRS Track Loss signal I 1.6
90 AVDDC Power supply (3.3V) - 3.3
91 WBLIN
92 CSLFLT (NC) - - 1.2
93 RFDIF (NC) - - -
94 AVSSC Ground - 0
95 PLFLT2 Capacitor terminal for PLL I 0
96 PLFLT1 Capacitor terminal for PLL I 0
97 AVSSB Ground - 0
98 ARF RF (+) input I 1.6
99 NARF RF (-) input I 1.6
100 VHALF Reference voltage input (1.65V) I 1.6
101 RVI Reference voltage terminal I 1.4
9
CQ-D5501W

Pin
No. Name Description I/O (V)
102 VREFH Reference voltage input (2.2V) I 2.1
103 DSLF2 Capacitor terminal 2 for DSL I 1.6
104 DSLF1 Capacitor terminal 1 for DSL I 1.5
105 AVDDB Power supply (3.3V) - 3.3
106 JITOUT Jitter Monitor output O 2
107 AVDDA Power supply (3.3V) - 3.3
108 TECAPA Reference voltage input 1.6
109 AD0 FE signal input I 1.6
110 AD1 AS signal input I 1.6
111 AD2 TEph/ TE3b/ TEpp signal input I 2
112 AD3 RF envelope input I 2.4
113 AD4 (NC) - - -
114 AD5 (NC) - - -
115 AD6 (NC) - - -
116 AD7 (NC) - - -
117 AD8 (NC) - - -
118 AVSSA Ground - 0
119 PWM0 Focus Drive output O 1.4
120 PWM1 Tracking Drive output O 1.7
121 VSS Ground - 0
122 VDD3 Power supply (3.3V) - 3.3
123 IDGT IDGT (for RF Amp) O 1.3
124 DTRD DTRD (for RF Amp) O 3.3
125 MONI 0 - - -
126 MONI 1 - - -
127 MONI 2 - - -
128 MONI 3 - - -
129 MONI 4 (NC) - - -
130 MONI 5 (NC) - - -
131 NEJECT (NC) - - -
132 NTRYCL (NC) - - -
133 DMARQ DMA Request O 0
134 NIOWR Data Write signal I/O 3.3
135 VDD3 Power supply (3.3V) - 3.3
136 VSS Ground - 0
137 NIORD Data Read signal I/O 3.3
138 IORDY Ready signal output O 3.3
139 NDMACK (+5V pull-up) I 5
140 INTRQ Interrupt Request (for MPEG) O 0
141 NIOCS16 Data Bus width select O 3.3
142 DA1 Address 1 (for MPEG IC) I/O 0
143 NPDIAG (+5V pull-up) I/O 5
144 DA0 Address 0 (for MPEG IC) I/O 0
145 VSS Ground - 0
146 VDD3 Power supply (3.3V) - 3.3
147 DA2 Address 2 (for MPEG IC) I/O 0
148 NCS1FX Chip Select 1 (for MPEG IC) O 3.3
149 NCS3FX Chip Select 3 (for MPEG IC) O 3.3
150 NDASP (+5V pull-up) I/O 5
151 HDD15 Data 15 (for MPEG IC) I/O 0
152 HDD0 Data 0 (for MPEG IC) I/O 0
153 HDD14 Data 14 (for MPEG IC) I/O 0
154 HDD1 Data 1 (for MPEG IC) I/O 0
155 HDD13 Data 13 (for MPEG IC) I/O 0
156 VDD3 Power supply (3.3V) - 3.3
157 VDD15 Power supply (1.5V) - 1.5
158 VSS Ground - 0
159 HDD2 Data 2 (for MPEG IC) I/O 0
160 HDD12 Data 12 (for MPEG IC) I/O 0
161 HDD3 Data 3 (for MPEG IC) I/O 0
162 HDD11 Data 11 (for MPEG IC) I/O 0
163 HDD4 Data 4 (for MPEG IC) I/O 0
164 HDD10 Data 10 (for MPEG IC) I/O 0
165 HDD5 Data 5 (for MPEG IC) I/O 0
166 VSS Ground - 0
167 VDD3 Power supply (3.3V) - 3.3
Pin
No. Name Description I/O (V)
168 HDD9 Data 9 (for MPEG IC) I/O 0
169 HDD6 Data 6 (for MPEG IC) I/O 0
170 HDD8 Data 8 (for MPEG IC) I/O 0
171 HDD7 Data 7 (for MPEG IC) I/O 0
172 VDDH Reference Voltage - 5
173 NRESET Reset I 3.3
174 MASTER Master/Slave Select I 0
175 SERIAL (NC) - - -
176 SERIAL (NC) - - -
IC101 : YESAM298
Pin
No. Name Description I/O (V)
1 VEE Power supply (+3.3V) - 3.3
2 LA4 Address 4 (Memory) I/O 1.3
3 LA5 Address 5 (Memory) I/O 1.5
4 LA6 Address 6 (Memory) I/O 1.9
5 LA7 Address 7 (Memory) I/O 1.3
6 LA8 Address 8 (Memory) I/O 1.2
7 LA9 Address 9 (Memory) I/O 2.1
8 VSS Ground - 0
9 VCC Power supply (+2.0V) - 2
10 LA10 Address 10 (Memory) I/O 0.6
11 LA11 Address 11 (Memory) I/O 2.3
12 LA12 Address 12 (Memory) I/O 1.8
13 LA13 Address 13 (Memory) I/O 1.7
14 LA14 Address 14 (Memory) I/O 1.4
15 LA15 Address 15 (Memory) I/O 1.1
16 LA16 Address 16 (Memory) I/O 1.6
17 VSS Ground - 0
18 VEE Power supply (+3.3V) - 3.3
19 LA17 Address 17 (Memory) I/O 1.1
20 LA18 Address 18 (Memory) I/O 0.8
21 LA19 Address 19 (Memory) I/O 1.4
22 LA20 (NC) - - -
23 LA21 (NC) - - -
24 RESET Reset I 3.9
25 TDMDX/
RSEL (+3.3V Pull-up) - -
26 VSS Ground - 0
27 VEE Power supply (+3.3V) - 3.3
28 TDMDR
(NC) - - -
29 TDMCLK
(NC) - - -
30 TDMFS (NC) - - -
31 TDMTSC
(NC) - - -
32 TWS/SEL
PLL2 TWS (for Audio D/A) O 1.7
33 TSD0/SEL
PLL0 TSD0 (for Audio D/A) O 0
34 VSS Ground - 0
35 VCC Power supply (+2.0V) - 2
36 TSD1/SEL
PLL1 (Not Used) - -
37 TSD2 (Not Used) - -
38 TSD3 (NC) - - -
39 MCLK MCLK (for Audio D/A) O 1.6
40 TBCK TBCK (for Audio D/A) O 1.7
41 SEL
PLL3/PDIF
OUT
Digital output O 1.6
42 SPDIF IN
(NC) - - -
43 VSS Ground - 0
44 VCC Power supply (+2.0V) - 2
10
CQ-D5501W