Panasonic CQ-VD6503W User manual

ORDERNo.ACED060502C3
AUTOMOTIVE AFTERMARKET
CQ-VD6503W
Dual DINIn-Dash 6.5” Widescreen Color LCD Monitor/DVDReceiver
SPECIFICATIONS
Specifications*
1

General
Power Supply DC 12V (11V - 16V),
Test Voltage14.4V
NegativeGround
Current Consumption Less than10A(During Disc
Playback)
Power Output 18W×4ch(1kHz, 1%, 4 )
MaximumPower Output 50W×4ch
CompatibleSpeaker
Impedance 4
VideoInput Signal CompositeVideoSignal, / 1.0Vp-p
(75 )
AudioInput Sensitivity 2Vrms
VideoOutput Signal CompositeVideoSignal, / 1.0Vp-p
(75 )
Pre-AmpOutput Voltage 2Vrms
Pre-AmpOutput Impedance Less than600
FM StereoRadio
FrequencyRange 87.5- 108MHz
UsableSensitivity 7dB/ V
StereoSeparation 40dB (1kHz)
S/N Ratio 63dB
AM Radio
FrequencyRange 531 - 1602kHz
UsableSensitivity 25 dB/ V
ImageRejection Ratio 50 dB
AudioSection
Output Voltage/Impedance 2Vrms/600
FrequencyCharacteristics
(When“LARGE” is
Selected)
Front L/R, Center, / Rear
(Surround) L/R 20Hz - 20kHz (±1 dB)
DelayTime
DolbyDigital
Center 0-5ms
Rear (Surround) L/R 0-15 ms
DolbyProLogic
Rear (Surround) L/R 15-30 ms
Distortion
Front L/R 0.01%(1kHz,0dB,PCM Input)
DynamicRange 96dB (During CD Playback)
S/N Ratio 100dB (During CD Playback)
Monitor
Storagetemperature range -20°C -+80°C
LiquidCrystal Panel 6.5-inchwide
2

ScreenDimensions(W×H×
D) 143 × 79 × 164mm
Number of Pixels 280,880 pixels
(234 vertical × 400 horizontal × 3)
ValidPixel Ratio Over 99.99%
DisplayMethod Transparent colorfilter format
DriveMethod TFT (ThinFilmTransistor)
activematrixformat
Dimensions** (W× H × D) 178 × 100 × 165 mm
Weight** 2.4kg
*Specificationsand thedesign are subject topossible
modification without notice duetoimprovements.
** Dimensionsand Weight shownare approximate.
-Abovespecificationscomplywith EIAstandards.
2006 Matsushita ElectricIndustrial Co., Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
3

1. ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using leadfree solderwill have a PbF stampon the PCB.
Caution :
-Pb free solder has ahigher melting point than standard solder;
Typicallythe melting point is50 -70°F (30 -40°C)higher. Please
use asoldering iron with temperature control and adjust itto 700 ±
20°F (370 ± 10°C). Incase of using high temperature soldering
iron, please be careful not to heat too long.
-Pb free solder will tend to splash when heated too high (about
1100°F/600°C)
-Thislead free solder will be used for the products after serial No.
1,000,001.
2. FEATURES
-Simultanous Multi-Device Connection (with Expansion Module
(hub unit)
-Expansion Module(The optional Hub unit: CY-EM100N)
-Connectabledevices
-The optional adapter allowsyou to connect the optional Panasonic
DVDchanger unit(CX-DH801N).
-The optional adapter allowsyou to connect the optional Panasonic
4

CD changer unit(CX-DP880N).
-TV Tuner (The optional PanasonicTV tuner unit: CY-TUP153N).
-The optional adapter allowsyou to connect the optional iPod
series./ <ControllableiPod/software version> / 3rdgeneration iPod/ver.2.3/ 4rdgeneration iPod/ver.3.1/ iPod
Photo/ver. 1.2/ iPod mini/ver. 1.4/ iPod nano/ver. 1.0
-Hands-Free Phone System (The optional Bluetooth hands-free kit:
CY-BT100N).
-Integration of the monitor, FM/AMradio, DVDVideo, Video CD
player and CD/MP3/WMAplayer
-Built-inAVInput/Output Terminals.
-Built-inDolbyDigital decoder, DTS decoder.
-Built-inDSP.
-GUI (GraphicUser Interface).
-Disc type and input signal auto-detection.
-CSAuto (CircleSurround Automotive).
-Touch Panel Operation.
-DVD-R, DVD-RWPlayback.
-IDcode.
-Differences Among 4Models
3. REPLACING THE FUSE
Use fuses of the same specifiedrating (15A). Using different substitutes orfuses withhigher
ratings, orconnecting the unit directlywithout a fuse, couldcause fire ordamage tothis unit.
4. MAINTENANCE
Yourproducts is designedand manufacturedtoensure a minimumof maintenance. Use a soft
clothforroutine exteriorcleaning. Neveruse benzine, thinnerorothersolvent.
5. LASER PRODUCTS
5

6. DIMENSIONS
7. WIRING CONNECTION
6

8. DISASSEMBLY INSTRUCTIONS
8.1. How to Remove the FlexiblePCB(AP1)
7

8.2. How to Disassemble&assemble
8

9. TERMINALS DESCRIPTION
9.1. MainBlock
IC601 : C2DBLK000114
9

Pin
No. Port Description I/O Vol
(V)
1 AVREF0 Reference voltage forA/
D converter - 3.2
2 AVSS Ground forA/D converter - 0
3 ANTCNT Antenna control O 3.2
4 RCA SW Voice change of DVD-CH
and HUB. H: HUB L:VTR2 O 0
5 AVREF1 Reference voltage forA/
D converter - 3.2
6Touch
RESET TouchPanel reset O 3.2
7 HUB CNT HUB control. L: HUB CPU
Communication O3.2
8 IC/FLMD0 Flashmemoryupdate
control - 0
9VDD +3V powersupply - 3.2
10 REGC Bypass capacitor
terminal forvoltage reg. -2.5
11 VSS Ground - 0
12 X1 Crystal osillatorterminal I 1.1
13 X2 Crystal osillatorterminal - 1.2
14 /RESET Systemreset I 3.2
15 XT1 (Connecting toground) - 0
16 XT2 NoConnection - -
17 EVENT EVENTinput (forHUB) I 0
18 CH STB/
XM DET2 Changerdata strobe I 5.0
19 RDS DATA RDS data I 3.3
20 RDS CLK RDS clock I 0
21 MAIN CNT Main_Control (forHUB) O 5.0
22 OSD CS OSD chipselect O 1.0
23 OSD DO OSD control data O 0.6
24 OSD CLK OSD data shift clock O 2.2
25 XM TX(MO) XM data O 5.0
26 CH DATA/
XM RX Changerdata I 0
27 CH CLK/
XM DET1 Changerclock / XM detection signal I 3.1
28 REMO
DATA Ext. remote control signal I 5.0
29 CHC REM
OUT Changerremote control code O5.1
30 I2C CLK I2C bus clock O 5.1
31 I2C DATA I2C bus data O 5.1
32 OSD
RESET
OSD reset O 3.2
10

RESET
11

Pin
No. Port Description I/O Vol
(V)
33 EVSS Ground forext. unit - 0
34 EVDD +3V powersupplyforext.
unit - 3.2
35 DVD
TX(MO) DVD deck TX data O 3.2
36 DVD
RX(MI) DVD deck RX data I 3.2
37 BEEP Beepsignal O 0
38 AMP CNT Ext. AMP control O 3.2
39 AMP STB Ext. AMP stand-by O 5.0
40 TFT SI(MI) TFT unit communication
data I 0
41 TFT
SO(MO) TFT unit communication data O 0.5
42 TFT CLK TFT unit communication
clock O 5.0
43 AMP MUTE Internal powerAMP mute O 0
44 SYS ON Systempower(5V)
control forSW PCB O 0
45 NAVI
REMO
OUT
NAVI remote control data O 0
46 ENTER ENTER key I 3.3
47 FRONT
MUTE Audiosignal (BEEP NAVI) mute O 5.0
48 VD COUNT Vertical drive signal count I 5.0
49 REAR
MUTE Videoout mute O 5.0
50 SYSID1 Connectedequipment
recognition (forHUB) I 5.0
51 SYSID2 Connectedequipment
recognition (forHUB) I 5.0
52 SYS
MUTE (F) Systemmute (FRONT) O 5.0
53 SYS
MUTE (S) Systemmute (SURROUND) O 5.0
54 SYS
MUTE (C) Systemmute (CENTER) O 5.0
55 SYS
MUTE(SW) Systemmute (SW) O 5.0
56 BATT
SENS Batterylevel detection I 5.0
57 ACC SENS ACC level detection I 5.0
58 PULSE Monitorposition
detection pulse I 5.0
12

Pin
No. Port Description I/O Vol
(V)
59 SYS PWR Systempowercontrol O 5.0
60 MAIN PWR Mainpowercontrol O 3.2
61 MONI PWR Monitorpowercontrol O 3.2
62 NAVI RM
CH NAVI remote control output change O 0
63 SEC LED LED blinking function for
CodeSecurityemphasis O 3.2
64 EJECT
LED (NC) NoConnection - -
65 NAVI LED NAVI LED on/off O 0
66 MA Drive mechanismcontrol
signal O 3.2
67 MB Drive mechanismcontrol
signal O 3.2
68 MC Drive mechanismcontrol
signal O 3.2
69 BVSS Ground forbus I/F - 0
70 BVDD Powersupplyforbus I/F - 3.2
71 FAN CNT Fanmotorpowercontrol O 3.2
72 ROTARY.1 Rotaryencodersignal
(VOLDOWN) I 0
73 ROTARY.2 Rotaryencodersignal
(VOLUP) I 3.3
74 INITDET2 Destination detection I 0
75 RADIO
CNT Radiopowercontrol O 3.2
76 DVD MUTE DVD mute request / Flash
memoryupdate cnt. I 3.3
77 DSP SCK Shift clock forDSP
communication data O 2.8
78 DSP SDA DSP communication data O 3.1
79 DSP
RESET DSP reset O 3.2
80 DVD CNT DVD deck powercontrol O 3.2
81 DVD
RESET Reset signal forDVD deck control MPU O 3.2
82 FRAM
HOLD F-RAM hold O 0
83 FRAM CLK Shift clock forF-RAM
data O 0
84 FRAM DO F-RAM serial data O 0
85 FRAM CS F-RAM chipselect O 3.2
86 FRAM WP F-RAM write protect O 0
87 SW PWR Switching powersupply
frequencychange O 0
13

Pin
No. Port Description I/O Vol
(V)
88 MODE MODE keydetection I 3.2
89 JOY A/D ADC input terminal for
joystic signal I 3.3
90 NAVI DISP NAVI displayactivity
detection I3.3
91 NAVI
SENS NAVI systemconnection detection I3.3
92 SIDE
BRAKE Side break detection I 3.3
93 INITDET Destination detection I 0
94 POSI
SENS ADC input terminal for monitorposition signal I 2.4
95 NAVI
MUTE NAVI mute I 0
96 OFFSET
DET PowerIC abnormality detection I 0
97 AD KEY ADC input terminal for
AD keysignal I 3.3
98 REVERSE REVERSE signal
detection I3.3
99 FRAM DI F-RAM serial data I 0
100 V_NAVI NAVI RGB signal change O 0
9.2. TFT Block
IC401 : C2BBYY000199
Pin
No. Port Description I/O Vol (V)
1 MONI CNT TFT monitorpower
supplycontrol output O4.9
2 BLCNT Backlight control output O 4.9
3TILT LED
(NC) TILT button LED control - -
4ASPECT
LED (NC) LED control of ASPECT button - -
5EJECT
LED EJECT_LED control O -
6NAVI LED NAVI LED control O -
7SRC LED SOURCE button LED
control O -
8NC NC(GND connection) I 0
9SELF
WRITE Self writing switch output O 0
10 TFT
RESET Systemreset input - 5.0
14

Pin
No. Port Description I/O Vol (V)
11 NC NC(GND connection) I 0
12 NC NC(GND connection) I 0
13 IC/ Vpp Internal connection and
flashmemory
programming mode
drawing in
- 0
14 X2 Crystal oscillatorclock I 2.7
15 X1 Crystal oscillatorclock I 2.4
16 REGC Regulatoroutput
stabilitycapacity
connection
-2.5
17 VSS Grand potential forin - 0
18 EVSS Grand potential for
external - 0
19 VDD Positive powersupply
forin - 4.9
20 EVDD Positive powersupply
forexternal - 4.9
21 SCL I2C bus clock output
forDAC O 4.9
22 SDA I2C bus data output for
DAC O 4.9
23 NC NC(OPEN) - -
24 NC NC(OPEN) - -
25 NC NC(OPEN) - -
26 NC NC(OPEN) - -
27 NC NC(OPEN) - -
28 NC NC(OPEN) - -
29 NC NC(OPEN) - -
30 NC NC(OPEN) - -
31 NC NC(OPEN) - -
32 NC NC(OPEN) - -
33 NC NC(OPEN) - -
34 NC NC(OPEN) - -
35 NC NC(OPEN) - -
36 NC NC(OPEN) - -
37 NC NC(OPEN) - -
38 HD IN HD signal input I 4.4
39 VD IN PALN/PALM judgment
VD signal input I4.7
40 NC NC(OPEN) - -
41 NC NC(OPEN) - -
42 NC NC(OPEN) - -
43 NC NC(OPEN) - -
44 NC NC(OPEN) - -
15

Pin
No. Port Description I/O Vol (V)
45 OSD
CSEL(NC) NC(OPEN) - -
46 X- TransistorSW output
fortouchpanel side X (
- pole)
O 0
47 Y- TransistorSW output
fortouchpanel side Y (
- pole)
O 0
48 X+ TransistorSW output
fortouchpanel side X (
+ pole)
O 4.9
49 Y+ TransistorSW output
fortouchpanel side Y (
+ pole)
O 4.9
50 RX ForFlashrewriting I 0.5
51 TX ForFlashrewriting O 0
52 IP SO IP Serial data output O 0
53 IP SI IP Serial data input I 0
54 IP SCK IP Serial clock output O 0
55 IP STR IP STR control O 0
56 IP RESET IP RESEToutput O 0
57 NC NC(OPEN) - -
58 NC NC(OPEN) - -
59 AVREF Reference voltage
input 0 of A/D converter - 4.9
60 AVSS A/D convertergrand
potential - 0
61 XG Touchpanel side X
withrespect to- pole I 0
62 YG Touchpanel side Y
withrespect to- pole I 1.2
63 XR Touchpanel side X
withrespect to+ pole I 0
64 YR Touchpanel side Y
withrespect to- pole I 1.2
65 LIGHT
SENS DIMMER input I 3.9
66 A/D KEY A/D keyinput forTILT
and OPEN/CLOSE I 4.9
67 A/D KEY GND connection I 0
68 A/D KEY GND connection I 4.9
69 NC NC(OPEN) - -
70 TFT CLK Serial communications
clock forthe mainCPU I 4.9
16

Pin
No. Port Description I/O Vol (V)
71 TFT SO/
TFT COM Serial communications data input forthe main
CPU
I 0.6
72 TFT SI/
TFT DATA Serial communications data output forthe
mainCPU
O 0.4
73 TouchSW Switchoutput fortouch
panel SW detection O4.1
74 NC NC(OPEN) - -
75 NC NC(OPEN) - -
76 NC NC(OPEN) - -
77 NC NC(OPEN) - -
78 NC NC(OPEN) - -
79 NC NC(OPEN) - -
80 BUS KILL Forconnected
confirmation of self
adjustment treatment
device
I 0
9.3. DVDServo Block
IC501 : C1AB00002402
Pin No. Port Descriptions I/O Vol (V)
1 VDDIO I/O pad power (3.3V) - 3.3
2MD10 SDRAMdata bus I/O 0
3MD11 SDRAMdata bus I/O 0.6
4VDD Corepower (1.8V) - 1.8
5MD12 SDRAMdata bus I/O 0
6VSSIO I/O pad ground - 0
7MD13 SDRAMdata bus I/O 0.7
8MD14 SDRAMdata bus I/O 0.5
9MD15 SDRAMdata bus I/O 0
10 VDDIO I/O pad power (3.3V) - 3.3
11 /DQM1 SDRAMdata byte enable O 0
12 MA9 SDRAMaddress bus O 0
13 MA8 SDRAMaddress bus O 0
14 VSSIO I/O pad ground - 0
15 MA7 SDRAMaddress bus O 2.3
16 MA6 SDRAMaddress bus O 1.9
17 VSS Coreground - 0
18 MA5 SDRAMaddress bus O 1.1
19 VDDIO I/O pad power (3.3V) - 3.3
20 MA4 SDRAMaddress bus O 2.0
21 MA3 SDRAMaddress bus O 2.3
22 MCLK SDRAMclock O 1.7
23 VSSIO I/O pad ground - 0
24 CKE SDRAMclock enable O 3.3
25 MA2 SDRAMaddress bus O 2.3
26 MA1 SDRAMaddress bus O 1.0
17

Pin No. Port Descriptions I/O Vol (V)
27 VDDIO I/O pad power (3.3V) - 3.3
28 MA0 SDRAMaddress bus O 1.0
29 MA10 SDRAMaddress bus O 0
30 MA11 Notused - -
31 VSSIO I/O pad ground - 0
32 MA12 SDRAMaddress bus O 2.1
33 MA13 SDRAMaddress bus O 2.1
34 VDD Corepower (1.8V) - 1.8
35 /CS0 SDRAMprimarybankchip select O 2.7
36 VDDIO I/O pad power (3.3V) - 3.3
37 /RAS SDRAMcommand bit O 3.1
38 /CAS SDRAMcommand bit O 2.9
39 /WE SDRAMcommand bit O 3.2
40 VSSIO I/O pad ground - 0
41 /DQM0 SDRAMdata byte enable O 0
42 /DQM2 SDRAMdata byte enable O 0
43 MD16 SDRAMdata bus I/O 0.5
44 VDDIO I/O pad power (3.3V) - 3.3
45 MD17 SDRAMdata bus I/O 0.5
46 MD18 SDRAMdata bus I/O 0.5
47 VSS Coreground - 0
48 MD19 SDRAMdata bus I/O 0.7
49 VSSIO I/O pad ground - 0
50 MD20 SDRAMdata bus I/O 0
51 MD21 SDRAMdata bus I/O 1.5
52 MD22 SDRAMdata bus I/O 1.0
53 VDDIO I/O pad power (3.3V) - 3.3
54 MD23 SDRAMdata bus I/O 0
55 MD24 SDRAMdata bus I/O 0.5
56 MD25 SDRAMdata bus I/O 0.5
57 VSSIO I/O pad ground - 0
58 MD26 SDRAMdata bus I/O 0.5
59 MD27 SDRAMdata bus I/O 0.8
60 MD28 SDRAMdata bus I/O 0
61 MD29 SDRAMdata bus I/O 1.0
62 VDDIO I/O pad power (3.3V) - 3.3
63 MD30 SDRAMdata bus I/O 0.7
64 MD31 SDRAMdata bus I/O 0.5
65 /DQM3 SDRAMdata byte enable O 0
66 /CS1 Notused O -
67 VSSIO I/O pad ground - 0
68 SPDIF S/PDIF digital audio output O 1.3
69 VSS Coreground - 0
70 AIN Digital audio inputfor digital micro I 3.3
71 AOUT3 Serial audio data (Left/RightCH) O 0
72 AOUT2 Serial audio data (Center/LFECH) O 0
73 AOUT1 Serial audio data (Sound Left/RightCH) O 0
74 AOUT0 Serial audio data (Left/RightCH) O 0
75 VDDIO I/O pad power (3.3V) - 3.3
76 PCMCLK Audio DAC PCMsampling clock O 1.8
77 VDD Corepower (1.8V) - 1.8
78 ACLK Audio interface serial data clock O 1.7
79 LRCLK Left/Rightchannel clock O 1.7
80 /SRST Reset signal O 3.3
18

Pin No. Port Descriptions I/O Vol (V)
81 /RSTP Power on reset I 3.3
82 VSSIO I/O pad ground - 0
83 RXD1 Notused - -
84 SSPIN1 SSP1data in / UART116Xclock I/O 15
85 VSS Coreground - 0
86 SSPOUT1 SSP1sata out/ UART1DTR I/O 0
87 SSPCLK1 SSP1clock / UART1CTS I/O 3.3
88 SSPCLK0 Notused - -
89 VDD Corepower (1.8V) - 1.8
90 SSIN0 Notused - -
91 VDDIO I/O pad power (3.3V) - 3.3
92 SSPOUT0 Notused - -
93 TXD0 UART0serial data O 3.2
94 RXD0 UART0serial data I 3.0
95 /CTS0 Notused - -
96 /RTS0 Notused - -
97 VSSIO I/O pad ground - 0
98 CXI Crystal Oscillator terminal I 1.6
99 CXO Notused - -
100 OSCVSS Oscillator ground - 0
101 OSCVDD Oscillator power (1.8V) - 1.8
102 MVCLVDD Main/Video clock PLL power (3.3V) - 3.3
103 SCEN Notused - -
104 MVCKVSS Main/Video clock PLL Ground - 0
105 ACLKVSS Audio clock PLL ground - 0
106 SCMD Notused - -
107 ACLKVDD Audio clock PLL power - 3.3
108 VDDDAC DAC digital power (1.8V) - 1.8
109 VSSDAC DAC digital ground - 0
110 CVBS2/CR/R Composite Cr/ComponentCr/SCARTRed O 0.5
111 IOM Cascaded DAC differential output O 1.0
112 C/CB/B Chrominance/ComponentCb/SCARTCb O 0.7
113 VAA3 DAC analog power (3.3V) - 3.3
114 Y/G Luminance/SCARTG O 0.4
115 VSSA DAC analog ground - 0
116 VREF Notused - -
117 VAA - - 1.8
118 CVBS/C Composite/S-Video Chrominance O 0.5
119 RSET Currentsetting resistor connection O 1.4
120 COMP Compensation capacitor connection O 2.0
121 VSS Coreground - 0
122 VCLK Notused - -
123 VSYNC Notused - -
124 HSYNC Notused - -
125 VDDIO I/O pad power (3.3V) - 3.4
126-131 VI07-02 Notused - -
132 VSSIO I/O pad ground - 0
133 Notused - -
134 Notused - -
135 VDD Corepower (1.8V) - 1.9
136-139 AD31-28 Notused - -
140 VDDIO I/O pad power (3.3V) - 3.4
141-144 AD27-24 Notused - -
145 /PWE3 Notused - -
19

Pin No. Port Descriptions I/O Vol (V)
146 AD23 Notused - -
147 VSSIO I/O pad ground - 0
148-150 AD22-20 Notused - -
151-153 AD19-17 Address/Data bus I/O 0
154 VDDIO I/O pad power (3.3V) - 3.4
155 AD16 Address/Data bus I/O 0
156 /PWE2 Notused - -
157, 158 AD15, 14 Address/Data bus I/O 0
159 VDD Corepower (1.8V) - 1.9
160 SCLK External busclock O 2.1
161 ACK ProgrammableWAIT/ACK/RDYcontrol I 3.4
162 VSSIO I/O pad ground - 0
163-168 AD13-08 Address/Data bus I/O 0
169 VDDIO I/O pad power (3.3V) - 3.4
170 /PWE1 Notused - -
171 VSS Coreground - 0
172-176 AD7-3 Address/Data bus I/O 0
177 VSSIO I/O pad ground - 0
178-180 AD02-00 Address/Data bus I/O 0
181 VDDIO I/O pad power (3.3V) - 3.4
182 /PWE0 Byte write enable O 0
183 ALE Address latch enable O 0
184-187 LA0-3 Latch address O 3.3
188 VSSIO I/O pad ground - 0
189 RD Read signal O 3.4
190 LHLDA Notused - -
191 LHLD Notused - -
192 VDD Corepower (1.8V) - 1.9
193 /PCS0 Peripheral chip select 0 O 3.4
194 XI01 Notused - -
195 DACCS2 DAC outputselect 2 O 3.4
196 VDDIO I/O pad power (3.3V) - 3.4
197 DACCS1 DAC outputselect 1 O 3.4
198 NINTCPPM Notused - -
199 CPPMCS Notused - -
200 XI06 Notused - -
201 VSS Coreground - 0
202 FRAMCS FRAMchip selection O 0
203 DACRST DAC reset O 0
204 VSSIO I/O pad ground - 0
205 FEPCS FrontEnd Pro. LSI chip select O 3.4
206 FEPRST FrontEnd Pro. reset O 3.4
207 SODCCS SODC LSI chip selection O 3.4
208 NINTHOST HOSTinterrupt I 3.4
209 NINTDDC DDC interrupt I 3.2
210 VDDIO I/O pad power (3.3V) - 3.4
211 NINTDSC DSC interrupt I 3.5
212 VDD Corepower (1.8V) - 1.9
213 DSYNV DVD parallel modesector SYNC I 3.4
214 DREQ DVD parallel modedata request O 3.4
215 DCLK Data sampling clock I 3.4
216 DSTB Parallel modedata valid/Serial modeclock I 0.7
217 DVD0 DVD driveparallel data port I 0
218 VSSIO I/O pad ground - 0
20