Panasonic RXFS430 - RADIO CASSETTE-LOW P User manual

Panasonic
Stereo Radio Cassette Recorder
RX-FS430
Operating Instructions
Before connecting, operating or adjusting this product, :
please read these instructions completely. Te C hn ica l S pecific ati ons
Supplied accessories
Radio
Frequency range: FM; 88—108 MHz
AM; 525-1705 kHz
Tape recorder
Track system: 4 track, 2 channel, stereo
Recording system: AC bias, magnet erase
Monitor system: Variable sound monitor
AC power cord Frequency range: 70~10000 Hz (Normal)
(SJA175-A) General
Power requirement: AC; 120 V, 60 Hz
Power consumption;
12 W
Battery; 9 V
{6 "D" size
batteries)
Speakers: 2 Woofers; 10cm (4")
Product Service nae 2 Tweeters; 1.5 cm (%6")
Output; HEADPHONES; 320
Do not attempt to remove the cover(s) or repair the unit Dimensions (WxHxD): 460x149x149 mm
yourself. Refer servicing to qualified personnel only. (18%4"x 574" x 57%")
Weight: 2.4 kg without batteries
(5 lb. 5 oz.)
Product information
Note:
Specifications are subject to change without notice.
For
product
service,
product
information
or
assistance
with
Weight
and
dimensions
are
approximate.
product operation, refer to the servicenter directory.
LP]
RQT2146-P

The model number and serial number.of this product
can be found on either the back or the bottom of the
unit,
Please note them in the space provided below and
retain them for future reference.
RX-FS430
MODEL NUMBER
SERIAL NUMBER
CAUTION:
TO PREVENT ELECTRIC SHOCK
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
CAUTION:
Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate
this device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsu-
lated “dangerous voltage” within the prod-
uct’s enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the liter-
ature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO. NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOIS-
TURE.
| Precautions
Before using this unit please read these operating in-
structions carefully. Take special care to follow the warnings
indicated on the unit itself as well as the safety suggestions
listed below.
Afterwards keep them handy for future reference.
Safety
_
. Power Source -- The unit should be connected to power
supply only of the type described in the operating instruc-
tions or as marked on the unit.
. Polarization -- If the unit is equipped with a polarized AC
power plug (a plug having one blade wider than the
other), that plug will fit into the AC outlet only one way.
This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug
should stil! fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
. Power Cord Protection -- AC power supply cords
should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
Never take hold of the plug or cord if your hand is wet,
and always grasp the plug body when connecting or
disconnecting it.
. Nonuse Periods -- When the unit is not used, turn the
power off. When left unused for a long period of time, the
unit should be unplugged from the household AC outlet.
N
w
ia
Installation
Environment
ama
. Water and Moisture -- Do not use this unit near
water—for example, near a bathtub, washbowl, swim-
ming pool, or the like. Damp basements should also be
avoided. .
. Heat -- The unit should be situated away from heat
sources such as radiators and the like. It also should not
be placed in temperatures less than 5°C (41°F) or greater
than 35°C (95°F).
Ld

Placement
= . Ventilation -- The unit should be situated so that its
location or position does not interfere with its proper
ventilation. Allow 10 cm (4”) clearance from the rear of
the unit.
. Foreign Material -- Care should be taken so that objects
do not fall into and liquids are not spilled into the unit. Do
not subject this unit to excessive smoke, dust, me-
chanical vibration, or shock.
. Magnetism -- The unit should be situated away from
equipment or devices that generate strong magnetism.
. Stacking -- Do not place heavy objects, other than
system components, on top of the unit.
. Surface -- Place the unit on a flat, level surface.
. Carts and Stands -- The unit should be used only with a
cart or stand that is recommended by the manufacturer.
The unit and cart combination should be moved with
care. Quick stops, excessive force, and
uneven surfaces may cause the unit
and cart combination to overturn.
N
Q
a=
an
~
. Wail or Ceiling Mounting -- The unit should not be
mounted to a wall or ceiling, unless specified in this
operating instructions.
Maintenance
Clean the cabinet, panel and controls with a soft cloth lightly
moistened with mild detergent solution.
Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
Service
1. Damage Requiring Service -- The unit should be
` serviced by qualified service personnel when:
(a) The AC power supply cord or the plug has been
damaged; or
(b) Objects have fallen or liquid has been spilled into the
unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not appear to operate normally or
exhibits a marked change in performance; or
(e) The unit has been dropped, or the enclosure —
damaged.
. Servicing -- The user should not attempt to service the
unit beyond that described in the operating instructions.
All other servicing should be referred to qualified service
personnel.
N
Listening caution
Selecting fine audio equipment such as the unit
you've just purchased is only the start of your
musical enjoyment. Now it’s time to consider
how you can maximize the fun and excitement
your equipment offers. This manufacturer and
the Electronic Industries Association’s Con-
sumer Electronics Group want you to get the
most out of your equipment by playing it at a
safe level. One that lets the sound come through loud and
clear without annoying blaring or distortion—and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort
level” adapts to higher volumes of sound. So what sounds
“normal” can actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe level
BEFORE your hearing adapts.
To establish a safe level:
eStart your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably
and clearly, and without distortion.
Once you have established a comfortable sound level:
®Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing
damage or loss in the future. After all, we want you listening
for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a
lifetime of fun and enjoyment. Since hearing damage from
loud noise is often undetectable until it is too late, this
manufacturer and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid pro-
longed exposure to excessive noise. This list of sound
levels* is included for your protection.
"The level used here is different from that displayed on the
system's display.
Decibel
Level Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock
at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet plane
180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.

Power Sources
To operate on battery power
Unplug the AC power cord from the household AC outlet
and the AC socket of the unit.
Insert six “D” size (R20/LR20 or equivalent, not included)
batteries into the battery compartment in the designated
numerical order.
t ®© €1 3K 2) O| Bottom sheif
Batteries installed with incorrect polarities may leak and
damage this unit.
@Do not mix batteries (old and new) or types (carbon and
alkaline, etc.).
eif the set is not used for a long period of time or is used
only from an AC power source, remove the batteries to
prevent potential damage from possible battery leakage.
elf you cannot open the cassette compartment cover when
running this unit on batteries, replace the batteries with
new ones, or use AC power source, and then perform the
operation once again.
Battery removal:
Insert your finger, and then
push out the batteries.
Battery life:
When the batteries get weak, the sound will become dis-
torted and the volume will decrease.
To operate AC power
Connect the AC power cord {included).
Household AC outlet
{AC 120 V, 60 Hz)
AC power cord (included)
AC IN~

Listening to Radio Broadcast
FM STEREO
1 SELECTOR Set SELECTOR to RADIO.
2 BAND Set BAND to the desired radio
== = band.
FM STEREO: To receive FM stereo
broadcasts
(If you have tuned into
an FM stereo broad-
cast, the FM STEREO
indicator will light.)
AM: To receive AM broad-
casts
elf FM stereo reception is poor, set BAND to FM. This
will reduce the noise and provide clear reception;
however, the broadcast will not be heard in stereo.
3 = Use TUNING to tune into a de-
sired broadcast.
4 owe es, Adjust VOLUME and TONE.
gw a w dl
The radio can be turned off by setting SELECTOR to TAPE/
CH3.
Adjust the antennas E)
FM:
Pull out the telescopic antenna and adjust its length and
angle for optimum reception.
AM:
Tum the unit in the direction which gives the best results.
How to use headphones
eReduce the volume level. Connect the headphones to the
headphones jack.
eAvoid listening for prolonged periods of time to prevent .
hearing damage.
Speakers are automatically cut off when the headphones
are connected.
(not included)

Listening to Tape
A|
1
SELECTOR
Set
SELECTOR
to
TAPE/
:
2 BISTOPIEJECT Press STOP/EJECT, and then in-
sert the tape.
|] You can use normal tapes only.
Insert the cassette with the exposed
tape facing up.
3 <Play Press PLAY to start playback.
. .
a", gate,
4 eee Adjust VOLUME and TONE.
To stop the playback:
Press STOP/EJECT.
To briefly interrupt the playback:
Press PAUSE.
To resume playback, press PAUSE again.
To fast forward or rewind the tape EJ
Press <</CUE or »P/REV while the tape is
stopped.
The tape will start moving at high speed.
To stop the fast forward or rewind operation, press STOP/
EJECT.
STOP/EJECT
To cue or review the tape E
During playback, press and hold <</CUE or
> /REV.
The recorded sound on the tape can be monitored at high
speed.
When the button is released, normal playback will resume.
Full auto stop:
When the tape reaches the end, the tape will automatically
stop.
44/CUE,> > /REV

Making a Recording
The recording level is automatically adjusted.
Recording from radio broadcast W
1 OSTOPÆJECT Press STOP/EJECT to insert the
[ tape.
2 SELECTOR Tune into the desired broadcast.
f : (See “Listening to Radio Broad-
BAND cast”.)
3 eG ë Press HANON.
L
To stop the recording:
Press STOP/EJECT.
To briefly interrupt recording:
Press PAUSE.
To resume recording, press PAUSE again.
Recording through the built-in
microphone E]
1
seiecton
Set
SELECTOR
to
TAPE/
O3.
TAP Aa
2 GASTOP/EJECT Press STOP/EJECT to insert the
C] tape.
3
PYRECORD]
Press
[E[xefe)zia).
l
Pause button:
Before beginning a recording, first press and lock PAUSE.
Then press Gage. (The tape will not move.)
When ready to record, press PAUSE to release it. This will
start tape movement for immediate recording. Do not use
PAUSE to stop the tape for a long period of time.
Monitoring:
The monitor system enables you to listen, through the
speakers or headphones, to the sound as it is being re-
corded.
When recording from the built-in microphone the sound
being recorded cannot be monitored.
Erasure of tape:
When recording, previously recorded signals on the tape
will be erased automatically.

Care & Use
Concerning cassette tapes
Selection of cassette tapes
You can use normal tapes only.
Cassette tapes exceeding 90 minutes:
These tapes are handy for their long playback and record-
ing time but be careful about repeatedly stopping and start-
ing, rewinding and fast forwarding these tapes in short
intervals as they are thin, tend to stretch and may become
entangled in the machine.
If the tape loosens, take up the slack
Tape slack may cause the tape to break.
To prevent erasure of recorded sounds
Remove the erase-prevention tabs with a screwdriver or a
similar object.
To re-record on a protected cassette, cover the slot with
adhesive tape.
Side A
Tab for side A :
Adhesive tape
Tab for side B
improper tape storage:
You can damage tapes if you store them in the following
places:
èin high temperature [35°C (95°F) or higher] or high humid-
ity (80% or higher) areas
ein a strong magnetic field (near a speaker, on top of a TV,
etc.)
This can erase a recording.
*@Areas exposed to direct sunlight
Tape head care
To assure sound quality for recording and playback, be sure
to clean the tape heads after approximately every 10 hours
of use.
1 Open the cassette compartment cover by
pressing STOP/EJECT.
2 While pushing erase prevention lever down-
ward, press [i]see)sib).
3 Clean the heads, pinch roller and the capstan
with a cotton swab (or a soft, lint-free cloth)
slightly moistened with isopropyl alcohol.
Do not use any solution other than alcohol for head
cleaning.
Erase prevention lever
Cotton swab
It is recommended that the head assembly be demagne-
tized if distortion or poor sound quality persists after clean-
ing the heads. `
Demagnetize them using a demagnetizer available from an
audio store.
Panasonic Company, Division of
Matsushita Electric Corporation of America
One Panasonic Way
Secaucus, New Jersey 07094
Panasonic Sales Company, Division of
Matsushita Electric of Puerto Rico, Inc.
San Gabriel industrial Park
65th Infantry Ave. Km. 9.5
Carolina, P.R. 00630
Printed in Malaysia
Panasonic Company (West) of America, Division of
Matsushita Electric Corporation of America
6550 Katella Ave.
Cypress, CA 90630
Matsushita Electric of Canada Limited
5770 Ambler Drive,
Mississauga, Ontario L4W 2T3
RQT2146-P
FO893RO