Panasonic G600 Quick start guide

http://cxema.ru
Order Number: MCUK980101G8
Technical Guide
G600 Personal Cellular Telephone Handheld portable
EB-G600
Car mount k t
EB-HF600Z
Easy f t car mount k t
EB-HF600Z
Dual charger
EB-CR600
Issue 1
Rev s on 0

http://cxema.ru
Th s Techn cal Gu de s copyr ght and ssued on the str ct understand ng that t s not to be reproduced, cop ed, or
d sclosed to any th rd party, e ther n whole or part, w thout the pr or wr tten consent of Matsush ta Commun cat on
Industr al UK Ltd.
Every care has been taken to ensure that the contents of th s manual g ve an accurate representat on of the
equ pment. However, Matsush ta Commun cat on Industr al UK Ltd. accepts no respons b l ty for naccurac es that
may occur and reserves the r ght to make changes to spec f cat on or des gn w thout pr or not ce.
The nformat on conta ned n th s manual and all r ghts n any des gns d sclosed there n, are and rema n the
exclus ve property of Matsush ta Commun cat on Industr al UK Ltd.
Other patents apply to mater al conta ned n th s publ cat on:
BULL CP8 PATENTS
Comments or correspondence concern ng th s manual should be addressed to:
Customer Support Department,
Matsush ta Commun cat on Industr al UK Ltd.,
Colthrop,
Thatcham,
Berksh re. RG19 4ZD.
ENGLAND
© 1998 Matsush ta Commun cat on Industr al UK Ltd.
Issue 1 MCUK980101G8
Rev s on 0 Techn cal Gu de

http://cxema.ru
MCUK980101G8 Issue 1
Techn cal Gu de Rev s on 0
TABLE OF CONTENTS
1 INTRODUCTION
1.1 Purpose of th s Gu de ..............................................1-1
1.2 Structure of the Gu de ..............................................1-1
2 INTERFACES AND TEST POINTS
2.1 Introduct on ...................................................2-1
2.2 Interfaces ....................................................2-1
2.3 Test Po nts ...................................................2-6
3 RF OVERVIEW
3.1 Introduct on ...................................................3-1
3.2 Funct onal Descr pt on..............................................3-1
4 TRANSMITTER
4.1 Introduct on ...................................................4-1
4.2 Funct onal Descr pt on..............................................4-2
5 RECEIVER
5.1 Introduct on ...................................................5-1
5.2 Funct onal Descr pt on..............................................5-2
6 BASEBAND OVERVIEW
6.1 Introduct on ...................................................6-1
6.2 Funct onal Descr pt on..............................................6-1
7 GEMINI
7.1 Introduct on ...................................................7-1
7.2 Funct onal Descr pt on..............................................7-1
8 VEGA
8.1 Introduct on ...................................................8-1
8.2 Funct onal Descr pt on..............................................8-1
9 POWER SUPPLIES
9.1 Introduct on ...................................................9-1
9.2 Overv ew ....................................................9-1
9.3 Power-up ....................................................9-2
9.4 Power-down ...................................................9-3
9.5 Power Management ...............................................9-4
10 ACCESSORIES
10.1 Handsfree Un t - C rcu t Descr pt on ......................................10-1
10.2 Dual Charger .................................................10-5

http://cxema.ru
WARNINGS AND CAUTIONS
WARNING
The equ pment descr bed n th s manual conta ns polar sed capac tors ut l s ng l qu d electrolyte. These dev ces
are ent rely safe prov ded that ne ther a short-c rcu t nor a reverse polar ty connect on s made across the
capac tor term nals. FAILURE TO OBSERVE THIS WARNING COULD RESULT IN DAMAGE TO THE
EQUIPMENT OR, AT WORST, POSSIBLE INJURY TO PERSONNEL RESULTING FROM ELECTRIC SHOCK
OR THE AFFECTED CAPACITOR EXPLODING. EXTREME CARE MUST BE EXERCISED AT ALL TIMES
WHEN HANDLING THESE DEVICES.
CAUTION
The equ pment descr bed n th s manual conta ns electrostat c sens t ve dev ces (ESDs). Damage can occur to
these dev ces f the appropr ate handl ng procedure s not adhered to.
ESD Handling precautions
A work ng area where ESDs may be safely handled w thout undue r sk of damage from electrostat c d scharge,
must be ava lable. The area must be equ pped as follows:
Working Surfaces - All work ng surfaces must have a d ss pat ve bench mat, SAFE for use w th l ve equ pment,
connected v a a 1M2 res stor (usually bu lt nto the lead) to a common ground po nt.
Wrist Strap - A qu ck release sk n contact dev ce w th a flex ble cord, wh ch has a bu lt n safety res stor of between
5k2 and 1M2 shall be used. The flex ble cord must be attached to a d ss pat ve earth po nt.
Containers - All conta ners and storage must be of the conduct ve type.
Batteries
Th s equ pment may conta ns an nternal battery n add t on to the external battery packs. These batter es are
re-cyclable and should be d sposed of n accordance w th local leg slat on. They must not be nc nerated, or
d sposed of as ord nary rubb sh.
Issue 1 v MCUK980101G8
Rev s on 0 Techn cal Gu de

http://cxema.ru
1 INTRODUCTION
1.1 Pu pose of this Guide
Th s gu de conta ns techn cal nformat on for the Panason c G600 personal cellular telephone system operat ng on
the GSM network. Procedures for nstall ng, operat ng and serv c ng (e.g. d sassembly and test ng) the telephone
system are prov ded n the assoc ated Serv ce Manual.
1.2 St uctu e of the Guide
The gu de s structured to prov de serv ce-eng neer ng personnel w th the follow ng techn cal nformat on on the
GSM mob le telephone:
1. Interface deta ls and relevant test po nts.
2. Funct onal descr pt on of each sect on of the mob le telephone.
3. Deta led descr pt on of each sect on of the mob le telephone.
MCUK980101G8 Sect on 1 Issue 1
Techn cal Gu de 1 - 1 Rev s on 0
INTRODUCTION

http://cxema.ru
2 INTERFACES AND TEST POINTS
2.1 Int oduction
Th s sect on prov des deta ls on connect ons between the RF and Baseband PCB and other nterfaces on G600.
2.2 Inte faces
. .1 Baseband and RF
Th s deta ls the 50-way connector between the RF and baseband PCB.
No. Signal Name Function Connection Status
1 BAT TEMP Battery Temperature
measurement s gnal
ADIN3 of VEGA(10b tAD)
2 CHARGE ON Charge control s gnal for
Dual Charger Extended I/O: Q(1) H:Charge On
L:Charge Off
3 GND
4 TX AUDIO TX AUDIO analogue
s gnal AUXIN of VEGA
5 RX AUDIO RX AUDIO analogue
s gnal AUXOUT of VEGA
6 GND
7 nADP SENSE Opt onal Adaptor
detect on s gnal
ADIN4 of VEGA(10b tAD)
8 nHF SENSE Handsfree connect on
sense s gnal IO(11) of GEMINI L:HF connected
H:HF d sconnected
9 LO2SEL 2nd Local Frequency
control s gnal TSPACT(4) of GEMINI L:RX 8 MON slot
H:TX slot
10 BUZZ- Buzzer control s gnal BUZZIN of Charge IC
11 BUZZ+ Buzzer control s gnal REGFB of Charge IC 6V MAX
12 SIM RST SIM Interface: Reset
s gnal SIM RST of GEMlNI Depends on SIM Card
13 SIM IO SIM Interface: I/O s gnal SIM I/O of GEMINI 3.25/372=8736.56baud
14 SIM CLK SIM Interface: Clock
s gnal SIM CLK of GEMINI 3.25MHz clock
15 TX ON Transm tter block power
control s gnal TSPACT(10) of GEMINI H:On, L: Off
16 PA ON PA power control s gnal TSPACT(11) of GEMINI H:On, L:Off
17 RF ON RF common block power
control s gnal TSPACT(5) of GEMINI H:On, L: Off
18 RX ON1 Rece ver block power
control s gnal1 TSPACT(6) of GEMINI H:On, L: Off
19 RX ON2 Rece ver block power
control s gnal2 TSPACT(7) of GEMINI H:On, L:Off
20 nRADIO_MUTE Rad o Mute control s gnal
for Car Extended I/O: Q(4) L: Rad o Mute
H – Z:Rad o Un-Mute
MCUK980101G8 Sect on 2 Issue 1
Techn cal Gu de 2 - 1 Rev s on 0
INTERFACES AND TEST POINTS

http://cxema.ru
No. Signal Name Function Connection Status
21 VIB_ON V brator control s gnal Extended I/O: Q(3) H: V brat on On
L: V brat on Off
22 nON_HOOK ON HOOK detect on
s gnal 10(9) of GEMINI H: Off Hook
L: On Hook
23 PA_RAMP RF Output power control
s gnal of PA APC of VEGA(5b tDA) 64 step
24 VBAT Battery Power Supply BAT
VOLT:ADIN1(10b tAD)
L -lON: 7.2V
N -MH: 4.8V
25 DCOUT 3.5V DC/DC output
power supply 3.44V ±5%
26 D5V 5.0V DC/DC output
power supply for SIM 5.0V ± 2.4%
27 EXT_PWR External Power Supply nEXT_PWR: lO(2) of
GEMINI 9.4V Max
28 VDD Power supply for V brator
29 GND
30 13MHZCLK 13MHz Ma n (Master)
Clock MCLK (more than 0.5V)
31 SERIAL_UP Ser al Interface (Upl nk) GEMINI USART(8251) Baud rate:115.2, 57.6,
38.4, 28.8, 19.2, 9.6(k)
32 IGNITION Ign t on sense s gnal nlGNITION: IO(4) of
GEMINI
H: Ign t on On, L(H – Z):
Ign t on Off
33 SERIAL_DOWN Ser al Interface
(Downl nk) GEMINI USART(8251) 8 b t, Even, 1 stop
34 nLOGIC_PWR H/H power sense s gnal
for Opt onal equ pment
LOGIC_PWR: lO(1) of
GEMINI
L: H/H Power On
H – Z: H/H Power Off
35 nHF_ON HF Aud o block control
s gnal
HF_ON: 10(3) of GEMINI L: HF Aud o On
H – Z: HF Aud o Off
36 BATID Battery Cell detect on
s gnal
BAT – ID :ADIN2 of
VEGA(10b tAD)
37 VREF_OUT Vega reference voltage
output s gnal for RF VMID of VEGA
38 DQX Downl nk nQ s gnal
39 DQ Downl nk Q s gnal
40 DIX Downl nk nl s gnal
41 Dl Downl nk I s gnal
42 GND
43 OCE Output Cancel Enable
s gnal
BCAL=TSPACT(l) of
GEMINI H: Enable
44 IFAGCEN IF AGC Enable s gnal for
RX IC TSPEN(4) of GEMINI H: Enable
L: D sable
45 PLL_STRB PLL ser al nterface
s gnal: Strobe TSPACT(9) of GEMINI H: Enable
L: D sable
46 PLL_SD PLL and AGC ser al
nterface s gnal: Data TSPDO of GEMINI
Issue 1 Sect on 2 MCUK980101G8
Rev s on 0 2 - 2 Techn cal Gu de
INTERFACES AND TEST POINTS

http://cxema.ru
No. Signal Name Function Connection Status
47 PLL_CLK PLL and AGC ser al
nterface s gnal: Clock TSPCLK of GEMINI
48 GND
49 UQX Upl nk nQ s gnal
50 UQ Upl nk Q s gnal
51 UI X Upl nk nl s gnal
52 UI Upl nk I s gnal
53 PL_CONT TX Power Level control
s gnal IO(6) of GEMINI H: TX PL5~1
L: TX PL12~19
54 VBAT Battery Power Supply BAT VOLT:
ADIN1(10b tAD)
L -ION: 7.2V
N -MH: 4.8V
55 DCOUT 3.5V DC/DC output
power supply 3.44V ± 5%
56 D5V 5.0V DC/DC output
power supply for SIM 5.0V ± 2.4%
57 EXT_PWR External Power Supply nEXT PWR: IO(2) of
GEMINI 9.4V Max
58 VDD Power supply for V brator AFC of VEGA (13b tDA)
59 GND
60 AFC TCVCXO Frequency
Control s gnal
MCUK980101G8 Sect on 2 Issue 1
Techn cal Gu de 2 - 3 Rev s on 0
INTERFACES AND TEST POINTS

http://cxema.ru
. . External Interface
G600 has 2 external connectors, a mult way connector for use w th a handsfree and data and add t onal contacts
for the charg ng the battery pack wh le n the desk top charger. Both nterfaces are electr cally and mechan cally
compat ble w th G600.
Hands ree and data connector (J001)
PIN Signal Direction
(from HH) Description
1 GND Power supply and d g tal s gnal ground
2 TX_AUDIO Input TX aud o
3 AUDIO_GND Aud o s gnal ground
4 nHF_ON Output Handsfree control s gnal
(Lo=ON, H -Zo=OFF)
5 nADP_SENSE Input Data adaptor select s gnal
6 SERIAL_UP Input UART up (9600, 33.8kbps)
7 SERIAL_DOWN Output UART down (9600, 33.8kbps)
8 EXT_PWR Input Power for charg ng
9 GND D g tal s gnal power supply ground
10 RX_AUDIO Output RX aud o s gnal (analogue)
11 nRADIO_MUTE Output Rad o mute
(Lo=mute, H -Zo=Not muted)
12 nHF_SENSE Input Handsfree select s gnal
(Lo=Handsfree mode)
13 nFLASH_WE /
PERF_PWR_ENBL Output Flash wr te enable and enable external per pheral
(Lo=Enable flash wr te)
14 IGNITION Input Cond t on of gn t on
(Lo=off, H =on)
15 nLOGIC_PWR Output Handheld state
(Lo=off, H =on)
16 PERF_PWR /
PA_ON Output Power ampl f er control s gnal and external per pheral
power supply
Charge Contacts
PIN Signal Description
20 EXT_PWR Power for charg ng
21 GND Ground
Issue 1 Sect on 2 MCUK980101G8
Rev s on 0 2 - 4 Techn cal Gu de
INTERFACES AND TEST POINTS

http://cxema.ru
Battery Contacts
PIN Signal Description
T TEMP Battery temperature sense
+ BATT + Battery pos t ve
- BATT - Battery negat ve
S SENSE Battery Type Sensor
SIM Inter ace
PIN SIGNAL
1 GND
25V
3 Not connected
4 Reset
5 Ser al nput/output
6 Clock
7 Not connected
8 Not connected
MCUK980101G8 Sect on 2 Issue 1
Techn cal Gu de 2 - 5 Rev s on 0
INTERFACES AND TEST POINTS