Panasonic KX-TCA155E User manual

ORDERNO. KMS0311868C2
DECTPortableStation
KX-TCA155E / KX-TCA155CE
(for United Kingdom and Europe)
2003 PanasonicCommunications Co., Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
1

IMPORTANTINFORMATION ABOUTLEAD FREE, (PbF), SOLDERING
If leadfree solderwas usedinthe manufacture of this product the printedcircuit boards will be
markedPbF.
Standardleaded, (Pb), soldercanbe usedas usual on boards without the PbF mark.
Whenthis mark does appearplease readand followthe special instructions describedinthis
manual on the use of PbF and howit might be permissible touse Pbsolderduring service and
repairwork.
1. ABOUT LEAD FREE SOLDER (PbF: Pb free)
Note:
Inthe information below, Pb, the symbol forleadinthe periodic table of elements, will referto
standardsolderorsolderthat contains lead.
We will use PbF solderwhendiscussing the leadfree solderusedinourmanufacturing process
whichis made fromTin(Sn), Silver(Ag), and Copper(Cu).
This model, and others like it, manufacturedusing leadfree solderwill have PbF stampedon
the PCB. Forservice and repairwork we suggest using the same type of solderalthough, with
some precautions, standardPbsoldercanalsobe used.
Caution
-PbF solder has amelting point that is50°F ~70°F (30°C~ 40°C)
higher than Pb solder. Please use asoldering iron with
temperature control and adjust itto 700°F ± 20°F (370°C± 10°C). In
case of using high temperature soldering iron, please be careful
not to heat too long.
-PbF solder will tend to splash ifitisheated much higher than its
melting point, approximately1100°F (600°C).
-Ifyou must use Pb solder on aPCB manufactured using PbF
solder, remove as much of the original PbF solder as possibleand
be sure that anyremaining ismelted prior to applying the Pb
solder.
-When applying PbF solder to doublelayered boards, please check
the component side for excess which mayflow onto the opposite
side (See the figure below).
2

1.1. Suggested PbF Solder
There are several types of PbF solderavailable commercially. While this product is
manufacturedusing Tin, Silver, and Copper
(Sn+Ag+Cu), you canalsouse Tinand Copper(Sn+Cu) orTin, Zinc, and Bismuth(Sn+Zn+Bi).
Please check the manufac
turer’s specific instructions forthe melting points of theirproducts and anyprecautions for
using theirproduct withother
materials.
The following leadfree (PbF) solderwire sizes are recommendedforservice of this product:
0.3mm, 0.6mm and 1.0mm.
1.2. How to recognize that Pb Free solder isused
1.2.1. Handset PCB
(Component View)
(FlowSolderSide View)
Note:
The location of the “PbF“ marks is subject tochange without notice.
1.2.2. ChargerUnit PCB
Note:
The location of the “PbF“ marks is subject tochange without notice.
2. FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable tostatic electricity.
Whenrepairing, the following precautions will helpprevent recurring malfunctions.
1. Cover the plasticparts boxes with aluminum foil.
2. Ground the soldering irons.
3

3. Use aconductive mat on the worktable.
4. Donot touch ICor LSI pins with bare fingers.
3. CAUTION
Dangerof explosion if batteryis incorrectlyreplaced. Replace onlywiththe same orequivalent
type recommendencedbythe manufacturer.
Dispose of usedbatteries according tothe manufacture’s Instructions.
4. SPECIFICATION
5. BATTERY
5.1. BatteryInstallation
Insert the batteries as shown. The negative end shouldbe insertedfirst.
Close the coveras indicatedbythe arrow.
-When you replace the batteries, the positive end shouldbe
removed first.
4

5.2. BatteryCharge
At the time of shipment, the batteries are not charged.
Please charge the batteries forabout 7 hours before initial use.
-When the batteryhas been completelycharged, the charge
indicator will change from red to green.
-Itisnormal for the PS and charger to feel warm whilethe batteryis
charging.
-Keep devices sensitive to magneticfields awayfrom the charger.
5

5.3. BatteryInformation
AfteryourPanasonic batteries are fullycharged[at 25°C]:
Operation Operating Time
While inuse (TALK) 10 hrs approx.
While not inuse (Standby) 120 hrs approx.
-Batterycharge maybe shortened depending on usage conditions
and ambient temperature.
-The batteries cannot be overcharged.
-The batteries will draineven whilethe unitis“OFF”.
-The PS can receive callswhilecharging.
-Batteryconsumption increases when the PS isused out of range.
If“ “flashes, power off the PS.
-Clean the handset and the charger contacts with asoft, drycloth
once amonth. Clean more often ifthe unitissubject to grease,
dust or high humidity. Otherwise the batteries maynot charge
properly.
-Read “Important Notice Concerning the Correct Use and Charging
of Ni-MHBatteries.”
5.4. Low BatteryWarning
The batteries needs tobe chargedwhen“ “ flashes orthe alarm sounds everyone
minute.*
*If the lowbatterywarning occurs during a conversation, you cancontinue the call forone
minute, thenthe call will be disconnectedautomatically.
5.5. Replacing the Batteries
If “ “flashes aftera fewtelephone calls evenwhenthe batteries have beenfully
charged, it is time toreplace the batterirs withnewones.
Before replacing the batteries, turnthe poweroff toprevent memoryloss. Replace the batteries.
Charge the newbatteries forat least 7 hours.
If you replace the batteries before the lowbatterywarning appears, the batterystrengthicon
maydisplayanincorrect reading. Inthis case, use the PS as normal withthe newbatteries
installed. Whenthe lowbatterywarning is displayed, charge the batteries forabout 7 hours.
6

The batterystrengthicon will thendisplaya correct reading.
-Replace both batteries and close the cover then charge the
handset for about 7hours.
Please orderPanasonic P03P(Ni-MH) batteries.
6. LOCATION OF CONTROLS
6.1. Handset
7

6.2. Soft KeyDisplay
Icons and information shownon the displaywill varydepending on the state of use. To select
anitemshownon the display, press the corresponding soft buttons.
8

7. SETTINGS
7.1. Connection
-USE ONLY the PanasonicAC ADAPTORPQLV200CEZ.
-USE ONLY the PanasonicAC ADAPTORPQLV200EZ.
7.2. Settings Menu Chart
7.2.1. Handset
9

7.3. KeyLock
You canlock the dialling buttons while the PS is inidle status.
10