Panasonic KX-TG8021FX User manual

PNQW1166ZA DC0808DJ0
FX-3/4
Connections
Important:
LIf you use a telephone line cord which is not supplied, the unit may not work
properly.
(220-240 V AC, 50 Hz)
To telephone
line
DSL/ADSL filter
(For DSL/ADSL service
users) Hook
Guide
Plug
“Click”
Use only the supplied Panasonic
AC adaptor PQLV207CE.
Use only the supplied
telephone line cord.
Press plug firmly.
Plug
Guide
Do not try to connect over the guide.
Base unit
(KX-TG8012)
Charger
Use only the supplied Panasonic
AC adaptor PQLV209CE.
Press plug firmly.
(220-240 V AC, 50 Hz)
Hooks
Model No. KX-TG8011FX/KX-TG8012FX
KX-TG8021FX
Quick Guide
To use this unit in your country, first change the unit’s region setting to match your
country. Change the unit’s display language as needed.
Refer to “Changing the unit’s region setting” in the operating instructions.
TG8011_8021FX(e)_QG.fm Page 1 Friday, August 22, 2008 3:28 PM

– 2 –
Battery installation/Battery charge
Charge for about 7 hours.
Note:
LUSE ONLY Ni-MH batteries AAA (R03) size.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Screen saver mode
The backlight goes dark when on a call or
turns off completely after 1 minute of
inactivity if the handset is not on the base
unit or charger.
Activate the handset display again by:
–pressing{<}or {>}when on a call.
–pressing{ih} at all other times.
Base unit *1 Charger *2
Rechargeable
Ni-MH ONLY
“Charging”is
displayed.
*1 Model shown is KX-TG8011.
*2 KX-TG8012
{ih}
TG8011_8021FX(e)_QG.fm Page 2 Friday, August 22, 2008 3:28 PM

– 3 –
Operating tips
Using the navigator key
The handset navigator key can be used to
navigate through menus and to select items
shown on the display by pressing {^}, {V},
{<}, or {>}.
To adjust the receiver or speaker volume,
press {^} to increase the volume, or press
{V} to decrease the volume repeatedly while
talking.
Soft keys
The handset features 3 soft keys. By
pressing a soft key, you can select the feature
shown directly above it on the display.
Menu icons
When in standby mode, pressing the middle soft key reveals the handset’s top-
menu. From here you can access various features and settings.
*1 KX-TG8011/KX-TG8012
*2 KX-TG8021
Display language (Handset) (default: English)
16 display languages are available.
You can select “Deutsch”, “English”, “Magyar”, “Polski”, “SlovenČina”,
“ČeŠtina”, “Hrvatski”, “Slovenscina”, “Eesti”, “LIETUVIŠKAI”,
“LatvieŠu”, “Românã”, “БЪЛГАРСКИ”, “Srpski”, “МАКЕДОНСКИ”, or “Shqip”.
1K(middle soft key) iNiM
2{V}/{^}: “Display Setup”iM
3{V}/{^}: “Select Language”iM
4{V}/{^}: Select your desired language. iMi{ih}
Note:
LIf you select a language you cannot read: {ih} iKiNiMi
{V} 2 times iMi{V} 4 times iMi{V}/{^}: Select your desired
language. iMi{ih}
{V}
{^}
Volume up
Volume down
{<}{>}
Icon Feature
jCaller List
XSMS (Short Message
Service)
KTime Settings*1
Icon Feature
IAnswer System*2
NHandset Setup
<Base Unit Setup
|Display Setup
TG8011_8021FX(e)_QG.fm Page 3 Friday, August 22, 2008 3:28 PM

– 4 –
Dialling mode (Handset) (default: Tone)
1K(middle soft key) i<iM
2{V}/{^}: “Dial Mode”iM
3{V}/{^}: Select the desired setting. iMi{ih}
Date and time (Handset)
1K(middle soft key) iNiM
2{V}/{^}: “Time Settings”iM
3{V}/{^}: “Set Date & Time”iM
4Enter the current date, month, and year.
5Enter the current hour and minute.
6Mi{ih}
Basic operations
Making/Answering calls (Handset)
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
To hang up {ih}
To adjust the receiver/
speaker volume
Press {^} or {V} repeatedly while talking.
Making a call using the redial
list
j(right soft key) i{V}/{^}: Select the desired
phone number. i{C}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
Handset ringer volume 1K(middle soft key) iNiM
2{V}/{^}: “Ringer Setup”iM
3{V}/{^}: “Ringer Volume”iM
4{V}/{^}: Select the desired volume. iMi
{ih}
TG8011_8021FX(e)_QG.fm Page 4 Friday, August 22, 2008 3:28 PM

– 5 –
Phonebook (Handset)
Adding entries 1n(left soft key) iK
2{V}/{^}: “New Entry”iM
3Enter the party’s name (16 characters max.).
iM
LYou can change the character entry mode by
pressing /.
4Enter the party’s phone number (24 digits max.).
iM
5{V}/{^}: Select the desired category.
iM2timesi{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1n(left soft key)
2{V}/{^}: Select the desired entry.
LYou can scroll through the phonebook entry by
pressing and holding {V} or {^}.
3{C}
Answering system (Base unit): KX-TG8021
Answering on/off Press {s}to turn on/off the answering system.
Listening to messages {6}
Basic operations
TG8011_8021FX(e)_QG.fm Page 5 Friday, August 22, 2008 3:28 PM

– 6 –
Frequently asked questions
Question Cause/solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit’s AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Re-position the
base unit and use the handset away from sources
of interference.
LThe handset is not registered to the base unit.
Register it (page 8).
Why can I not make calls? LThe dialling mode may be set incorrectly. Change
the setting (page 4).
Why is the handset display
blank or goes dark when on
a call?
LThe handset is in screen saver mode. Activate the
handset display again by:
– pressing {<}or {>}when on a call.
– pressing {ih} at all other times.
L“LCD Dimming”is set to “Off”while on charge.
Change the setting.
What should I do when the
handset does not turn on?
LMake sure the batteries are installed correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 14 hours max.
Not in use (standby): 240 hours (10 days) max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
Can I keep the handset on
the base unit or charger
when I am not using it?
LEven after the handset is fully charged, the
handset can be left on the base unit or charger
without any ill effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until 1is
displayed, but 3is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
TG8011_8021FX(e)_QG.fm Page 6 Friday, August 22, 2008 3:28 PM

– 7 –
What should I do to display
caller information?
LYou must subscribe to a Caller ID service. Contact
your service provider/telephone company for
details.
LThe message “You must first subscribe
to Caller ID.” will be displayed until you
receive caller information after subscribing to a
Caller ID service.
What should I do when noise
is heard, sound cuts in and
out?
LYou are using the handset or base unit in an area
with high electrical interference. Re-position the
base unit and use the handset away from sources
of interference.
LMove closer to the base unit.
LIf you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base
unit and the telephone line jack. Contact your
DSL/ADSL provider for details.
What should I do when the
operating time seems to be
shorter even after I fully
charged the batteries?
LClean the battery ends (S, T) and the charge
contacts with a dry cloth, and charge again.
What do I need to do to
erase y(Missed call) from
the display?
LThere are unviewed missed calls remaining. View
them and erase yin the following way.
1K(middle soft key) ijiM
2Press {V} to search from the most recent call,
or press {^} to search from the oldest call.
Frequently asked questions
Question Cause/solution
TG8011_8021FX(e)_QG.fm Page 7 Friday, August 22, 2008 3:28 PM

– 8 –
Registering a handset to a base unit
The supplied handset and base unit are pre-registered. If for some reason the
handset is not registered to the base unit, re-register the handset.
1K(middle soft key) iNiM
2{V}/{^}: “Registration”iM2times
3{V}/{^}: Select a base unit number. iM
Proceed with the operation for your model.
NKX-TG8011/KX-TG8012
Press and hold {x} for about 5 seconds.
(No registration tone)
NKX-TG8021
Press and hold {x} for about 5 seconds, until
the registration tone sounds.
LThe next step must be completed within
90 seconds.
Wait until “Enter Base PIN”is displayed. i
Enter the base unit PIN (default: “0000”). i
M
LWhen the handset has been registered
successfully, wstops flashing.
Handset
M
Base unit
{x}
{x}
Handset
M
TG8011_8021FX(e)_QG.fm Page 8 Friday, August 22, 2008 3:28 PM

– 9 –
Optional services (Caller ID and SMS)
If you subscribe to a Caller ID service,
– caller information will be displayed when a call is received, or
when viewing missed calls.
– you can identify who is calling by using different display colours
and ringer tones (phonebook category).
To use SMS, you must subscribe to a Caller ID and/or an appropriate service
such as SMS.
– SMS (Short Message Service)
012345
012345
TG8011_8021FX(e)_QG.fm Page 9 Friday, August 22, 2008 3:28 PM

– 10 –
Notes
TG8011_8021FX(e)_QG.fm Page 10 Friday, August 22, 2008 3:28 PM