Panasonic ES-RT53 User manual

© Panasonic Corporation 2012 Unauthorized copy-
ing and distribution is a violation of law.
Order Number SD1206E38CE
Rechargeable Shaver
Model No. ES-RT53
ES-RT33
Europe
CIS
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
3.1. Main unit and charging adaptor ------------------------ 3
4 Disassembly and Assembly Instructions ---------------- 4
4.1. Disassembly Instructions -------------------------------- 4
4.2. Cautions in Assembly ------------------------------------ 6
5 Schematic Diagram ---------------------------------------------- 8
5.1. ES-RT53 ----------------------------------------------------- 8
5.2. ES-RT33 ----------------------------------------------------- 8
6 Exploded View and Replacement Parts List ------------ 9
6.1. Exploded View for ES-RT53 ---------------------------- 9
6.2. Replacement Parts List ---------------------------------10
6.3. Exploded View for ES-RT33 ---------------------------11
6.4. Replacement Parts List ---------------------------------12

ES-RT33/ES-RT53
2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

ES-RT33/ES-RT53
3
3 Troubleshooting Guide
3.1. Main unit and charging adaptor

ES-RT33/ES-RT53
4
4 Disassembly and Assembly Instructions
4.1. Disassembly Instructions
Follow the procedure below to disassemble the main unit.
1. Remove the protective cap, the foil frame with outer foil
and the inner blade.
2.
NOTE: If you do not replace the trimmer or trimmer
handle, skip to No.4.
Slide the trimmer handle and unhook the trimmer handle
by inserting something like a slotted screwdriver or plastic
spatula into a slit.
NOTE:
In order to prevent the scratch or damage on the
housing, use the cushion under the screwdriver.
3. Loosen a screw and remove the bottom cover.
4. To remove the side panels, insert a small slotted screw-
driver into the housing and unhook.

ES-RT33/ES-RT53
5
5. Loosen four screws on and back side of housing A.
6. Take out the housing B, from the bottom side.
7. To remove the trimmer driving bar or the slit blade driving
bar, press bars outward.
8. And take out the battery assembly from housing A.
9. Remove the motor assembly and tube holder.
10. Remove the battery o-ring and washer in each battery.
Take out the rechargeable batteries from the chassis.

ES-RT33/ES-RT53
6
4.2. Cautions in Assembly
NOTE:
When reassembling, replace the new waterproof rubber.
Make sure whether there is NO foreign substance sticking
around a part covered with water seal.
4.2.1. Motor
Insert the tube into the projection of the housing and set the
tube holder firmly. Then hook the motor holder to the housing
and put the float springs properly.
4.2.2. Module
Align the projection of switch select button on housing A with
the groove of switch plate on module.
4.2.3. Rechargeable batteries
Insert the rechargeable batteries into chassis. Attach the bat-
tery o-ring and washer to the battery.
Put the battery assembly from the battery terminal side into
housing A, and insert the motor side into housing A.
NOTE:
While setting the battery assembly, pull the lead wires out in
order to prevent pinching. Then press fit the lead wires
neatly.
4.2.4. Driving bars
Set the trimmer driving bar and the slit blade driving bar.

ES-RT33/ES-RT53
7
4.2.5. Side panel
Set the side panel on the body and insert the projection on back
of side panel into the housing first. Then hook the front side
and the rear side of the side panel in order.
NOTE:
Make sure that the left and right side panels are firmly fitted
on both rear and front side.
4.2.6. Trimmer
1. Align the housing with the hooks of trimmer.
2. Confirm its operation or smooth movement of trimmer.

8
5 Schematic Diagram
5.1. ES-RT53
5.2. ES-RT33

ES-RT33/ES-RT53
9
6 Exploded View and Replacement Parts List
6.1. Exploded View for ES-RT53

ES-RT33/ES-RT53
10
6.2. Replacement Parts List
Safety Ref.
No.
Part No. Part Name & Description Qty/
unit
Remarks
1 WESRT33X7158 PROTECTIVE CAP 1
2 WESRT33S0048 OUTER FOIL FRAME 1
3 WES9087Y OUTER FOIL 1
4 WES9068Y INNER BLADE 1
5 WESRT33L1008 MOTOR ASSEMBLY 1
6 WESRT33K3268 FOIL RELEASE BUTTON 1
7 WESRT33L1088 TRIMMER DRIVING BAR 1
8 WES8176L1077 SLIT BLADE DRIVING BAR 1
9 WES8196L0328 WATERPROOF RUBBER 1
10 WES7046L0226 FLOAT SPRING 2 (2PCS/PK)
11 WES7046L0966 O-RING 1
12 WES7046L0236 TUBE HOLDER 1
13 WESRT53S3058 HOUSING A 1
14 WESRT53K3778 FRONT PANEL 1
15 WESRT33S3068 HOUSING B 1
16 WESRT53L2128 MODULE 1
17 WES7038L2508 RECHARGEABLE BATTERY 2 Ni-Mh Type, (2PCS/PK)
18 WES7025L0976 WASHER & O-RING SET 2 (2PCS/PK)
19 WESRT53K3368 SIDE PANEL 1
20 WESRT53K1508 TRIMMER 1
21 WESRT53K3848 BOTTOM COVER 1
21 WESRT53K3849 BOTTOM COVER 1 only for CIS
22 WES7023L6058 TAPPING SCREW 9 K2-8
23 WESRT53S3038 BODY BLOCK 1
23 WESRT53S3039 BODY BLOCK 1 only for CIS
24 WESRF41K7664 CHARGING ADAPTOR 1 C-2 PLUG
24 WESRF41K7660 CHARGING ADAPTOR 1 B-2 PLUG, for U.K.
24 WESRT51K7650 CHARGING ADAPTOR 1 C-2 PLUG, for CIS
25 WES8093H7056 CLEANING BRUSH 1
- WESRT53S8008 INDIVIDUAL BOX 1
- WESRT53S8009 INDIVIDUAL BOX 1 only for CIS
- WESRT53S8000 INDIVIDUAL BOX 1 only for U.K.
- WESRT33S8108 OPERATING INSTRUCTIONS 1
- WESRT33S8109 OPERATING INSTRUCTIONS 1 only for CIS