Panasonic ES7035-U1 User manual

ORDERNO. SD0509U43C1
E6
Wet/DryRechargeableShaver
ES7035-U1 / ES7037-U1
SPECIFICATIONS
SPECIFICATIONS
2005 Matsushita ElectricWorks, Ltd. All rights reserved.
Unauthorized copying and distribution isaviolation of law.
1
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

1. SCHEMATIC DIAGRAM
1.1. ES7035
1.2. ES7037
2. WIRING CONNECTION DIAGRAM
3. DISASSEMBLY INSTRUCTION
Followthe procedure belowtodisassemble the mainunit.
1. Remove the cap, the outer foil with foil frame and the inner blade.
2
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

2. Slide the trimmer handleup to open the trimmer and unhook the
trimmer handlebyinserting something like asloted screwdriver
or plasticspatulainto aslit.
NOTE: Make sure not toscratchordamage on the housing.
3. Remove trimmer and trimmer handle.
3
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

4. To remove the trimmer driving bar or the slitblade driving bar,
press bars outward.
5. Loosen ascrew and remove the bottom cover.
6. Slide downthe side panelsfor both sides.
4
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

7. Loosen twoscrewson front and four screwson the back side,
and remove twohousing clips.
8. Take out the housing B.
5
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

9. Remove the motor assemblyand tube holder.
10. And take out the batteryassemblyfrom housing A.
11. Remove the batteryo-ring and washer ineach battery. Take out
the rechargeablebatteries from the chassis.
4. CAUTION IN ASSEMBLY
6
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

NOTE: Whenreassembling, replace the newwaterproof rubber. Make sure whetherthere is NO
foreign substance sticking around a part coveredwithwaterseal.
4.1. Motor
Insert the motorand press fit the waterproof tube neatlyunderthe tube holder. And put the float
spring propery.
4.2. Rechargeablebatteries
Insert the rechargeable batteries intochassis. Attachthe batteryo-ring and washertothe
battery.
Put the batteryassemblyfromthe batteryterminal side intohousing A, and insert the motor
side intohousing A.
NOTE: Press fit the leadwire neatlyinordertoprevent pinching.
7
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

4.3. Module
Align the projection of switchselect button on housing A withthe groove of switchplate on
module.
4.4. Driving bars
Set the trimmerdriving barand the slit blade driving bar.
8
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

4.5. Side panel
Set the side panel on the bodyand slide it up until clicking the hook of panel at three locations.
NOTE: Make sure that the left and right side panels are firmlyfittedon bothrearand front side.
Fit the front side of hook first, thenon top and rearside.
4.6. Trimmer
1. Make sure ifthe bosses of handlearm insert into the holes of
trimmer.
2. Align the bosses of housing with the holes of trimmer, and hook
the trimmer handle.
3. Confirm its operation or smooth movement of trimmer.
9
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com

5. TROUBLESHOOTING GUIDE
(Referto WIRING CONNECTION DIAGRAM)
<TROUBLE> <CHECK.> <
REMEDY>
Motordoes not
rotate. <CHECK CHARGING ADAPTOR.> NO Replace
charging
Does not
charge.
Connect the ratedvoltage tothe normal mainunit bythe
charging adaptor. adaptor.
Functions fora
mo- Check if the charge status lampof mainunit is lit.
ment and stops. Supplythe ratedvoltage tothe adaptorand measure the
voltage. OK if it is
Does not
operate by approximatelyDC 5.8V betweenthe terminals of the plug withno-loadoperation.
AC power
source. OK
<CHECK RECHARGEABLE BATTERIES.> NO Replace
both
recharge-
Okayif the voltage of rechargeable batteries is more than
approximately able
batteries
the same
1.2V DC between(+) and (-) terminals. time.
10
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com