Panasonic KX-FM330GR User manual

©1999 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
KX-FM330GR
(for Greece)
Multi-Function Plain Paper FAX
Please file and use this manual together with the service manual for Model No. KX-FP320G/KX-FM330G,
Order No.KM79908300C2. This Service Manual indicates the main differences between; Original KX-
FP320G/KX-FM330G and KX-FM330GR.
Notice the PC interface-related features for KX-FM330 model (marked with “KX-FM330 only” in the original Service
Manual).
ORDER NO. KM79910324A2

1 INTRODUCTION
1.1. CONTROL PANEL
Change from original page 10 (1.12.2 CONTROL PANEL)
2
KX-FM330GR

1.2. CONNECTIONS
Change from original page 11 (1.13. CONNECTIONS)
Note:
·When you operate this product, the power outlet should be near the product and easily accessible.
·If the following message is displayed when the unit is plugged in, the recording paper set lever will be released.
Move the lever back.
3
KX-FM330GR

1.3. TO SELECT CHARACTERS WITH THE DIAL KEYPAD
Change from original page 19 (1.14.7. TO SELECT CHARACTERS WITH THE DIAL KEYPAD)
Pressing the dial keys will select a character as shown below.
Note: A hyphen entered in a telephone number is counted as two digits.
4
KX-FM330GR

2 TROUBLESHOOTING GUIDE
2.1. Program Mode Table
Change from original pages 65~66 (2.3.3.3.2. Remote programming)
Code Function Set Value Default Remote
Setting
001 Set date and time dd/mm/yy hh:mm AM/PM (01/Jan/99) NG
002 Your logo --------- --------- NG
003 Your telephone number --------- (None) NG
004 Transmission report mode 1:Error / 2:ON / 3:OFF ERROR OK
006 FAX ring count 2~4 2 NG
TAD/FAX ring count 2~4/TOLL SAVER/RINGER OFF 2 NG
Not available in TEL/FAX --------- VOX NG
010 Recording time 5MIN, 1MIN 5MIN OK
011 Remote TAD ID --------- ID=111 NG
014 PC link 1:ON / 2:OFF ON OK
015 Memory XMT 1:ON / 2:OFF OFF OK
022 Auto journal print 1:ON / 2:OFF ON OK
023 Overseas mode ON / OFF OFF NG
025 Delayed transmission ON / OFF OFF NG
026 Auto caller ID list 1:ON / 2:OFF ON OK
030 Silent FAX recognition ring 3 to 6 rings 3 OK
036 Rx reduction 1:92% / 2:86% / 3:72% / 4:100% 92% OK
039 LCD contrast 1:NORMAL / 2:DARKER NORMAL OK
041 Remote FAX activation code 1:ON / 2:OFF ON / ID=*9 NG
042 Message alert 1:ON / 2:OFF OFF OK
043 REC. time alert 1:ON / 2:OFF OFF OK
044 Receive alert 1:ON / 2:OFF ON OK
045 LINE MODE CO / PBX CO OK
046 Friendly rcv. 1:ON / 2:OFF ON OK
047 Voice guidance 1:ERROR / 2:ON / 3:OFF ON OK
054 Common greeting MSG.
REC. time 1:16s / 2:60s 16s OK
060 Message transfer 1:MESSAGE 2:PAGER 3:OFF OFF OK
061 Transfer greeting CHECK / RECORD / ERASE CHECK NG
067 Setting the ICM monitor 1:ON / 2:OFF ON OK
068 ECM Communication 1:ON / 2:OFF ON OK
070 FAX PAGER CALL ON / OFF OFF NG
076 FAX tone 1:ON / 2:OFF ON OK
077 Auto answer mode 1:TAD/FAX 2: FAX ONLY 3: TEL/FAX TAD/FAX OK
078 TEL/FAX delayed ring 2to 4rings 2 OK
079 Film detection 1:ON / 2:OFF ON OK
080 Set default YES / NO NO NG
501 Pause time set 001~600 x 100msec 050 OK
502 Flash time set 01~99 x 10msec 12 OK
510 VOX time 1:6sec / 2:4sec 4sec OK
520 CED frequency select 1:2100Hz / 2:1100Hz 2100 OK
521 International mode select 1:ON / 2:OFF ON OK
522 Auto standby select 1:ON / 2:OFF ON OK
523 Receive equalizer select 1:0.0km / 2:1.8km / 3:3.6km / 4:7.2km 0km OK
524 Transmission equalizer select 1:0.0km / 2:1.8km / 3:3.6km / 4:7.2km 0km OK
533 Setting the number of times that
message transfer is redialed 00~99 03 OK
534 Setting the message transfer / pager
call redial interval 001~999 065 OK
550 Memory clear --------- --------- NG
551 ROM check --------- --------- NG
552 DTMF signal tone test 1:ON / 2:OFF OFF NG
553 Monitor on FAX communication select 1:OFF / 2:Phase B / 3:ALL OFF OK
554 Modem test --------- --------- NG
555 Scanner test --------- --------- NG
556 Motor test --------- --------- NG
557 LED test --------- --------- NG
558 LCD test --------- --------- NG
559 Document jam detection select 1:ON / 2:OFF ON OK
561 Key test --------- --------- NG
5
KX-FM330GR

Code Function Set Value Default Remote
Setting
571 ITS auto redial time set 00~99 03 OK
572 ITS auto redial line disconnection time set 001~999 065 OK
573 Remote turn-on ring number set 01~99 15 OK
576 K break detect 1:ON / 2:OFF OFF OK
580 TAM continuous tone detection 1:ON / 2:OFF ON OK
590 FAX auto redial time set 00~99 03 OK
591 FAX auto redial line disconnection time set 001~999 065 OK
592 CNG transmit select 1:OFF / 2:ALL / 3:AUTO ALL OK
593 Time between CED and 300 bps 1:75ms / 2:500ms / 3:1sec 75ms OK
594 Overseas DIS detection select 1:1st / 2:2nd 1st OK
595 Receive error limit value set 001~999 100 OK
596 Transmit level set -15~00dBm -8 OK
598 Receiving Sensitivity -20~48dBm -44 OK
624 AT ring time out 1:3sec 2:5sec 3sec OK
711 TONE/PULSE selector 1:TONE 2:PULSE PULSE OK
717 Transmit speed select 1:14400 / 2:12000 / 3:9600 / 4:7200 /
5:4800 / 6:2400 14400bps OK
718 Receive speed select 1:14400 / 2:12000 / 3:9600 / 4:7200 /
5:4800 / 6:2400 14400bps OK
719 Ringer off in TEL/FAX mode 1:ON / 2:OFF ON OK
721 Pause tone detect 1:ON / 2:OFF ON OK
722 Redial tone detect 1:ON / 2:OFF ON OK
724 PC-FAX ATD BUSY TONE DETECT 1:ON / 2:OFF ON OK
731 CPC mode 1:A / 2:B / 3:OFF A OK
732 Auto disconnect cancel time 1:350ms / 2:1800ms / 3:OFF 350ms OK
745 Power ON film feed 1:ON / 2:OFF ON OK
763 CNG detect time for friendly reception 1:10s / 2:20s / 3:30s 30s OK
771 T1 timer 1:35s / 2:60s 35s OK
775 Monitoring of message transfer 1:ON / 2:OFF OFF OK
815 Sensor & VOX test --------- --------- NG
852 Print test pattern --------- --------- NG
853 Top margin 1~9 --------- OK
854 Left margin 1~8 --------- OK
861 A4 size set 1:ON / 2:OFF ON OK
880 Special service journal 1:Start --------- OK
890 TEL/FAX ring back tone 1:ON / 2:OFF ON OK
895 TEL/FAX Receive mode 1:TAD/FAX / 2:FAX FAX OK
991 Setup list 1:Start --------- OK
994 Journal list 1:Start --------- OK
999 Service list 1:Start --------- OK
OK means "can set".
NG means "can not set".
6
KX-FM330GR

2.2. Analog Board Section
Change from original page 81 (2.3.3.5. Analog Board Section)
This chapter provides the testing procedures required for the analog parts. A signal route to be tested is determined depending
upon purposes. For example, the handset TX route begins at the handset microphone and the signal is output to the telephone line.
The signal mainly flowing on this route is analog. You can trace the signal with an oscilloscope. The signal flow on each route is
shown in the Check Sheet here. If you find a specific problem in the unit, for example if you cannot communicate with the H/S, trace
that signal route locally with the following Check Sheet and locate the faulty point.
Note:
{ }: digital board
7
KX-FM330GR

2.3. Digital Speaker Phone
Change from original page 84 (2.3.3.5.1. Digital Speakerphone)
8
KX-FM330GR

2.4. USER MODE (The list below is an example of the SYSTEM SETUP
LIST the unit prints out.)
Change from original page 103 (2.4.3. USER MODE)
Note:
The above values are default.
9
KX-FM330GR

2.5. SERVICE FUNCTION TABLE
Change from original pages 104~105 (2.4.4. SERVICE FUNCTION TABLE)
Code Function Set Value Effective Range Default Remarks
501 Pause time set X 100 ms. 001~600 150
502 Flash time set X10ms. 01~99 2
510 VOX time 1:6sec 2:4sec 1, 2 2 --------
520 CED frequency select 1:2100 Hz 2:1100 Hz 1, 2 1 See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
521 International mode select 1:ON 2:OFF 1, 2 1See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the
default when transmission is
complete.
523 Receive equalizer select 1:0km 2:1.8km
3:3.6km 4:7.2km 1~4 1 When the telephone station is far from the unit or reception cannot
be performed correctly, adjust
accordingly.
524 Transmission equalizer select 1:0km 2:1.8km
3:3.6km 4:7.2km 1~4 1 When the telephone station is far from the unit or transmission
cannot be performed correctly,
adjust accordingly.
533 Setting the number of times that
message transfer is redialed 00~99 00~99 03 Selects the number of times that message transfer is redialed (not
including the first dialing).
534 Setting the message transfer /
pager call redial interval 000~999 000~999 065 Sets the interval of message transfer / pager call redial.
550 Memory clear: To reset the value to the default one, except the top margin (853)and left
margin (854). "START" input.
551 ROM check "START" input.
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See 2.5. TEST FUNCTIONS.
553 Monitor on FAX communication
select 1: OFF 2:PHASE B 3:ALL phases 1~3 1
554 Modem test See 2.5. TEST FUNCTIONS.
555 Scan check See 2.5. TEST FUNCTIONS.
556 Motor test 00 See 2.5. TEST FUNCTIONS.
557 LED test See 2.5. TEST FUNCTIONS.
558 LCD test See 2.5. TEST FUNCTIONS.
559 Paper jam detection select 1:ON 2:OFF 1, 2 1 See 2.2.1. Paper Jam.
561 KEY test See 2.5. TEST FUNCTIONS.
571 ITS auto redial time set X number of times 00~99 03 Selects the number of times that
ITS is redialed (not including the
first dial).
572 ITS auto redial line disconnection
time set X second 001~999 065 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of rings 01~99 15 Sets the number of rings before
the unit starts to receive a
document in the TEL mode.
576 K break detect 1:ON 2:OFF 1, 2 1 --------
580 TAM continuous tone detection 1:ON 2:OFF 1, 2 1 ON: STOP TAM operation when
Dial tone, etc. are detected.
590 FAX auto redial time set X number of times 00~99 03 Selects the number of redial times
during FAX communication (not
including the first dial).
591 FAX auto redial time disconnection
time set X second 001~999 065 Sets the FAX redial interval during FAX communication.
592 CNG transmit select 1:OFF 2:ALL 3:AUTO 1~3 2 Lets you select the CNG output
during FAX transmission. ALL:
CNG is output at phase A. AUTO:
CNG is output only when automatic
dialing is performed. OFF: CNG is
not output at phase A.
593 Time between CED and 300bps 1: 75 ms. 2:500 ms.
3:1 sec 1~3 1 See the Symptom/Countermeasure Table for long distance and
international calls in 2.3.3.3.1.
Defective facsimile section.
10
KX-FM330GR

Code Function Set Value Effective Range Default Remarks
594 Overseas DIS detection select 1:detects at the 1st
time 2:detects at the
2nd time
1, 2 1 See the Symptom/Countermeasure
Table for long distance and
international calls in 2.3.3.3.1.
Defective facsimile section.
595 Receive error limit value set X number of times 001~999 100 Sets the number of acceptable
error lines when the FAX
reconstructs the received data.
596 Transmit level set X dBm -15~00 8Selects the FAX transmission level.
598 Receiving sensitivity 43= -43 dBm 20~48 44 Used when there is an error
problem. See the
Symptom/Countermeasure Table
for long distance and international
calls in 2.3.3.3.1. Defective
facsimile section.
624 AT ring time out 1:3 sec 2:5 sec 1, 2 1 --------
711 TONE/PULSE select 1:TONE 2:PULSE 1, 2 2 --------
717 Transmit speed selection 1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6 1 Adjusts the speed to start training
during FAX transmission.
718 Receive speed selection 1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6 1 Adjusts the speed to start training
during FAX reception.
719 Ringer off in TEL/FAX mode 1:ON 2:OFF 1, 2 1 Sets the ringer switch off when a
call is received in the TEL/FAX
mode.
721 Pause tone detect 1:ON 2:OFF 1, 2 1Selects the tone detection for
pause in dialing.
722 Redial tone detect 1:ON 2:OFF 1, 2 1 Selects the tone detection mode
after redialing.
724 PC-FAX ATD busy tone detect 1:ON 2:OFF 1, 2 1 --------
731 CPC mode 1:A 2:B 3:OFF 1~3 1 Select the CPC signal detection
mode from the converter.
732 Auto disconnect 1:350ms
2:1.8sec
3:OFF
1~3 1 Select the detection start time of
auto disconnect.
745 Power ON film feed 1:ON 2:OFF 1, 2 1
763 CNG detect time for friendly
reception 1:10 sec 2:20 sec 3:30 sec 1~3 3 Selects the CNG detection tome of friendly reception.
771 T1 timer 1:35 sec 2:60 sec 1, 2 1 Sets a higher value when the
response from the other party
needs more time during FAX
transmission.
775 Monitoring of message transfer 1:ON 2:OFF 1, 2 2 --------
784 Voice prompt test Press “START”.
815 Sensor & Vox check See 2.5. TEST FUNCTIONS.
852 Print test pattern See 2.5. TEST FUNCTIONS.
853 Top margin 1~9 --------
854 Left margin 1~8 --------
861 A4 size set 1:ON 2:OFF 1, 2 1
880 Special service journal See 2.4.7. SPECIAL SERVICE
JOURNAL.
881 Journal 2 list See 2.4.7.3. PRINTOUT
EXAMPLE.
882 Journal 3 list See 2.4.7.3. PRINTOUT
EXAMPLE.
890 TEL/FAX 1st ring back tone 1:ON 2:OFF 1, 2 1 Selects whether the TEL/FAX 1st
ring back tone is ON or OFF in the
TEL/FAX mode.
895 TEL/FAX mode receiving mode
setting after bell time out 1:TAX 2:FAX 1, 2 2 --------
11
KX-FM330GR

2.6. SERVICE MODE SETTINGS (Example of a printed out list)
Change from original page 106 (2.4.5. SERVICE MODE SETTINGS)
Note:
The above values are default.
12
KX-FM330GR

2.7. HISTORY
Change from original pages 106~110 ([HISTORY] in 2.4.5. SERVICE MODE SETTINGS)
Note:
See the following descriptions of this report. Item No. (1) ~ (49) are corresponding to the listed items in 2.7.1 Descriptions of
the HISTORY Report.
13
KX-FM330GR

2.7.1. Descriptions of the HISTORY Report (Addition)
(1) ROM VERSION
EPROM version
(2) SUM
EPROM internal data calculation.
(3) YOUR LOGO
The user logo recorded in the unit. If it is not recorded, NONE will be displayed.
(4) YOUR TELEPHONE NUMBER
The user telephone number recorded in the unit. If it is not recorded, NONE will be displayed.
(5) FAX PAGER NUMBER
If you program a pager number into the unit, the pager number will be displayed here.
(6) FACTORY - CUSTOMER
This shows how many days from factory production until the user turns ON the unit.
(7) MONTH
The shows the very first month, date, year and time set by the user after they purchased the unit.
(8) DAY
The shows the very first month, date, year and time set by the user after they purchased the unit.
(9) YEAR
The shows the very first month, date, year and time set by the user after they purchased the unit.
(10) TIME
The shows the very first month, date, year and time set by the user after they purchased the unit.
(11) USAGE TIME
The amount of time the unit has been powered ON.
(12) FACTORY - NOW
This shows how many days from factory production until the user prints out this history list.
(13) TEL MODE
The amount of time the TEL mode setting was used.
(14) FAX MODE
The amount of time the FAX mode setting was used.
(15) TEL/FAX MODE
The amount of time the TEL/FAX mode setting was used.
(16) ANS/FAX MODE
The amount of time the ANS/FAX mode setting was used.
(17) FINAL RECEIVE MODE
The last set receiving mode by the user.
(18) TONE/PULSE SELECTION
The most recently used setting used, either TONE or PULSE.
(19) RECEIVE REDUCTION
The compression rate when receiving.
(20) SETTING NO. OF DIRECTORY
The recorded directory stations (one touch and JOG DIAL).
(21) NUMBER OF COPY
The number of pages copied.
(22) NUMBER OF RECEIVE
The number of pages received.
(23) NUMBER OF SENDING
The number of pages sent.
(24) NUMBER OF CALLER ID
The number of times Caller ID was received.
(25) NUMBER OF RECORDING MESSAGE
14
KX-FM330GR

The number of messages recorded in TAM.
(26) NUMBER OF PC SCAN
The number of times multifunction was used for the Scanner. (The number of pages scanned. If the unit does not have a PC
interface, NONE will be printed.)
(27) NUMBER OF PC-PRINT
The number of times multifunction was used for the Printer. (The number of pages printed. If the unit does not have a PC interface,
NONE will be printed.)
(28) NUMBER OF RECEIVING TO PC
The number of times received in the PC through the FAX serial interface (RS232C). (The number of pages received. If the unit does
not have a PC interface, NONE will be printed.)
(29) NUMBER OF SENDING FROM PC
The number of times transmitted from the PC through the FAX serial interface (RS232C). (The number of pages transmitted. If the
unit does not have a PC interface, NONE will be printed.)
(30) NUMBER OF PRINTING WARNING LIST
The number of warning lists printed until now.
(31) NUMBER OF PRINTING HELP
The number of help lists printed until now.
(32) NUMBER OF DIVIDED PRINTING IN FAX RECEPTION
The number of faxes received that were divided into more than one sheet since the unit was purchased.
(33) DETECTION OF RS232C
When the fax and PC serial cable (RS232C) are connected and the signal is received correctly, COMPLETE will be printed. For
models without a PC interface or when there is a PC interface but the signal cannot be received between the fax and PC,
INCOMPLETE will be printed. (The number of pages transmitted. If the unit does not have a PC interface, NONE will be printed.)
(34) NO. OF IQ-FAX LOADING -OK:
(35)NO. OF IQ-FAX LOADING -NG:
You may not be able to use IQ-FAX if the special subscriber information is not loaded from the IQ-FAX center before use.
Depending on the conditions of the communication line, it may not be completed in one time, so RETRIED will be performed. The
number of OK and NG IQ-FAX loadings will be printed.
(36) FAX MODE
Means the unit received a fax message in the FAX mode.
(37) MAN RCV
Means the unit received a fax message by manual operation.
(38) FRN RCV
Means the unit received a fax message by friendly signal detection.
(39) VOX
Means the unit detected silence or no voice.
(40) RMT DTMF
Means the unit detected DTMF (Remote Fax activation code) entered remotely.
(41) PAL DTMF
Means the unit detected DTMF (Remote Fax activation code) entered by a parallel connected telephone.
(42) TURN-ON
Means the unit started to receive after 15 rings. (Remote Turn On: Service Code #573)
(43) TIME OUT
Means the unit started to receive after Ring Time Out in the EXT-TAM or TEL/FAX mode.
(44) IDENT
Means the unit detected Ring Detection.
(45) CNG OGM
Means the unit detected the CNG while it was sending the Dummy Ring Back Tone in the TEL/FAX mode, or while answering a
call in the EXT-TAM mode. Or means the unit detected the CNG while it was sending the OGM in the ANS/FAX mode.
(46) CNG ICM
Means the unit detected the CNG while it was recording the ICM in the ANS/FAX mode.
(47) KEY OPERATION -1st 50:
15
KX-FM330GR

(48) KEY OPERATION -Last 50:
Indicates 2-digit codes. Refer to 2.5.2. BUTTON CODE TABLE.
·1st 50:
History of the first 50 key operations after purchase.
(Ex.) If the MENU, # and 9 buttons are pressed, 20, 3C and 39 will be printed.
·Last 50:
History of the last 50 key operations.
16
KX-FM330GR

2.7.2. SPECIAL SERVICE JOURNAL REPORTS (Addition)
Journal 2 and Journal 3 shown below, which are special journals giving the additional detailed information about the latest 35
communications, can be printed by Service Code 881 or 882. Remote printing function for the journal reports (JOURNAL,
JOURNAL 2 and JOURNAL 3) is also available for service technicians. (Refer to 2.3.3.3.2. Remote programming.) The JOURNAL
report only gives you basic information about a communication, but the other two journal reports provide different information on
the same item (communication).
HOW TO READ JOURNAL REPORTS:
Example:
1.Look at NO. 01 in the JOURNAL. If you want to know about the details about that item, see NO. 01 in the JOURNAL 2 and
the JOURNAL 3. You can get the following information.
* MODE: Fax transmission
* RCV. MODE: TEL
* TX SPEED: 9.6 kbps
* RESOLUTION: standard
* ENCODE: MH
* MAKER CODE: 79
2.Look at NO. 04 in the JOURNAL 2. CNG (0003) indicates that the CNG signal has been received three times since the
purchase date.
For further details, see 2.7.3. JOURNAL 2 and 2.7.4 JOURNAL 3.
17
KX-FM330GR

2.7.3. JOURNAL 2 (Refer to JOURNAL 2 in 2.7.5. PRINTOUT EXAMPLE.)...Addition
Journal 2 displays the additional detailed information about the last 35 communications.
Descriptions:
(1) RCV. MODE
Indicates which receive mode the unit was in when the unit received a fax message.
This information is also displayed when the unit transmitted a fax message.
(2) SPEED
Indicates the speed of the communication. If multiple pages are transmitted or received, it indicates the last page´scommunication
speed. If there is a communication error, “?” is displayed.
(3) RESOLUTION
Indicates the resolution of the communication. If multiple pages are transmitted or received, it indicates the last page´sresolution.
If there is a communication error, “?” is displayed.
(4) RCV-TRIG. (CNT.)
Indicates the trigger that causes the unit to switch to the fax receive mode. The available options are listed in JOURNAL 2 in 2.7.5.
PRINTOUT EXAMPLE. The values in parentheses indicate how many times the trigger has been used. (For example,“0003”
means three times.)
No. Display Function
1FAX MODE Means the unit received a fax message in the FAX mode.
2MAN RCV Means the unit received a fax message by manual operation.
3FRN RCV Means the unit received a fax message by friendly signal detection.
4VOX Means the unit detected silence or no voice.
5RMT DTMF Means the unit detected DTMF (Remote Fax activation code) entered remotely.
6PAL DTMF Means the unit detected DTMF (Remote Fax activation code) entered by a parallel connected
telephone.
7 TURN-ON Means the unit started to receive after 15 rings. (Remote Turn On: Service Code #573)
8TIME OUT Means the unit started to receive after Ring Time Out in the EXT-TAM or TEL/FAX mode.
9IDENT Means the unit detected Ring Detection.
10 CNG OGM Means the unit detected the CNG while it was sending the Dummy Ring Back Tone in the
TEL/FAX mode.
OR
Means the unit detected the CNG while it was sending the OGM in the ANS/FAX mode.
11 CNG ICM Means the unit detected the CNG while it was recording the ICM in the ANS/FAX mode.
(5) ERROR MEMORY
Indicates the reason why the unit received a fax message in memory.
If you look at No.11 in the JOURNAL 2 in 2.7.5. PRINTOUT EXAMPLE, it shows the fax message was received in memory due
to “PAPER OUT” error.
NO RESPONSE DISAPPEARED ON JOURNAL
The “NO RESPONSE DISAPPEARED ON JOURNAL” displays the information about the last 10 communications terminatedby
“No Response”. (Some of the communications terminated by “No Response” were not displayed in the JOURNAL.)
When a fax transmission cannot be performed because the other party´s unit is set to the TEL mode, “No response” will beprinted.
2.7.4. JOURNAL 3 (Refer to JOURNAL 3 in 2.7.5. PRINTOUT EXAMPLE.)...Addition
Descriptions:
(6) ENCODE
Compression Code: MH/MR
(7) MSLT
MSLT means Minimum Scan Line Time. Used only at the factory.
18
KX-FM330GR

(8) EQM
EQM means Eye Quality Monitor. Used only at the factory.
(9) ERROR LINE(RX)
When an error occurs while receiving a fax, this shows the number of error lines.
(10) MAKER CODE
This shows a 2 digit code of the other party´s fax machine brand.
0E: “KX” model
00: Unknown
79: “UF” model
19: “Zerox” model
2.7.5. PRINTOUT EXAMPLE (Addition)
19
KX-FM330GR

20
KX-FM330GR