Panasonic ER154-E8 User manual

1 SCHEMATIC DIAGRAM 2
2 WIRING CONNECTION DIAGRAM 2
3 DISASSEMBLY INSTRUCTIONS 3
4 ASSEMBLY INSTRUCTIONS 5
©2005 Matsushita Electric Works, Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
ER154-E8
5 TROUBLESHOOTING GUIDE 7
6 EXPLODED VIEW 8
7 REPLACEMENT PARTS LIST 8
AC/Rechargeable Hair Clipper for Professional
SPECIFICATIONS
Power source
A
C/Rechargeable
A
C 230V, 50Hz
Charging time 1 hour
Weight 200g
Supplied accessories Comb attachment (3mm/4mm, 6mm/9mm, 12mm/15mm)
Charging stand
Charging stand tray
Oil
Cleaning brush
CONTENTS
Page Page
ORDER NO. SD0512E51CE8

1 SCHEMATIC DIAGRAM
2 WIRING CONNECTION DIAGRAM
2
ER154-E8

Follow the procedure below to disassemble the main body.
1. Remove the attachment.
2. First, hold the handle of the hair clipper firmly with the
"Panasonic" name facing upward and set the dial to
"2.0mm", and push the upper part of the blade away from
the housing.
3. Loosen two screws tightening the spring for cutter and take
out the spring.
4. Remove the front panel.
5. With the dial at “ 2.0mm” , slide up the adjusting dial to the
blade side slightly pushing the adjusting arm with the
slotted-head screwdriver.
6. Loose a screw and take out the bottom cover.
3 DISASSEMBLY INSTRUCTIONS
3
ER154-E8

7. Loosen a screw and take out the name plate slightly
inserting the slotted-head screwdriver to unhook the side.
8. Separate housing A and B.
4
ER154-E8

1. Set the click button and the dial spring to the housing A.
2. Place the holding plate on the housing A firmly.
NOTE: Confirm if housing bosses completely cover the
hole of holding plate.
3. Insert the terminal pins into the hole of housing A firmly and
set the battery & module assembly into the housing A.
NOTE: Confirm to set the switch handle OFF position.
And make sure that the projection of switch handle
fixing frame connects to the slit of switch plate.
NOTE: Confirm the smooth movement and operation of
switch handle.
4 ASSEMBLY INSTRUCTIONS
NOTE: Always set the dial to "2.0mm" when removing or attaching the blade; otherwise the blade can not be attached.
Always set the dial to "0.8mm" when removing or attaching the comb attachment.
5
ER154-E8

4. Insert the motor facing the sticker on the housing B side.
NOTE: The motor has a own direction. Make sure to set
the proper direction when reassembling.
NOTE: Be certain that the lead wires are mounted in the
proper position without setting over the housing ribs.
NOTE: Confirm the smooth movement of click button
and the motor rotates when switching ON.
5. Close the housing B on the housing A.
NOTE: Make sure of the position of lead wires to
prevent pinching.
NOTE: Confirm that the motor rotates when switching
ON.
6. Applying GREASE (FLOIL G741) on the dial. Put two dials
together and align the slit of adjusting dial with the
projection of adjusting arm to assemble the dial.
NOTE: Confirm the smooth movement of adjusting dial.
7. Attach the dust-proof rubber.
8. Set the front panel.
9. Attach the spring for cutter tighten with two screws.
10. Attach the bottom cover with a screw.
11. Tighten a screw and set the name plate.
6
ER154-E8

5 TROUBLESHOOTING GUIDE
(Refer to WIRING CONNECTION DIAGRAM)
7
ER154-E8

6 EXPLODED VIEW
7 REPLACEMENT PARTS LIST
Ref. No. Part No. Part Name & Description Remarks Per Unit
1WER9792Y BLADE BLOCK 1
2WER151L9207 TAPPING SCREW *C K2.6-8 2
3WER154L0168 SPRING FOR CUTTER 1
4WER154S3968 FRONT PANEL 1
5WER154S3288 ADJUSTING DIAL 1
6WER150L0137 DUST-PROOF RUBBER 1
7WER154K3058 HOUSING A 1
8WER154L0458 DIAL CLICK BUTTON 1
9WER154L0158 DIAL CLICK SPRING 1
10 WER154L3178 HOLDING PLATE 1
11 WER154L3578 SWITCH CONTACT PLATE 1
12 WER154L1008 MOTOR 1
13 WER154L0778 CHASSIS BLOCK 1
14 WER154L2108 MODULE 1
15 WER154K2158 PLUG BLOCK 1
16 WER154L2508 RECHARGEABLE BATTERY *B Ni-Mh Type (2PCS/PK) 2
17 WER154K3068 HOUSING B 1
18 WER154K8408 NAME PLATE 1
19 WER160L9207 P-TIGHT SCREW M2.0-8 1
20 WER154K3178 BOTTOM COVER 1
21 WER160L9107 SCREW M2-6 1
22 WER154K7398 COMB ATTACHMENT A 3-4MM 1
23 WER154K7408 COMB ATTACHMENT B 6-9MM 1
24 WER154K7418 COMB ATTACHMENT C 12-15MM 1
25 WER154K7188 CHARGING STAND 1
26 WER154K7198 CHARGING STAND TRAY 1
27 WER154K7659 CHARGING ADAPTOR C-2 PLUG 1
28 WES76806761 CLEANING BRUSH 1
29 WER203X7918 OIL 1
-WER154K8008 INDIVIDUAL BOX 1
-WER154K8108 OPERATING INSTRUCTIONS 1
8
ER154-E8