Panasonic ER?GB50 User manual

© Panasonic Electric Works Co., Ltd. 2010.
All rights reserved. Unauthorized copying and distri-
bution is a violation of law.
Order Number SD1010A67CE
AC/Rechargeable Hair Clipper
Model No. ER-GB50
Asia
Middle East
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------- 8
6 Schematic Diagram ---------------------------------------------- 9
7 Exploded View and Replacement Parts List -----------10

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide

4
4 Disassembly and Assembly Instructions
4.1. Disassembly Instructions
1. Remove the blade.
2. Insert a slotted screwdriver into the slit of dial cover firmly
and raise it with the driver.
NOTE :
Make sure there is NO scratch or damage on the
parts.
3. Loosen a screw and take out the dial with the dial mount-
ing base.

5
4. Loosen two screws.
5. Remove the housing C.
6. Loosen a screw.
7. Insert a slotted screwdriver under the front panel, then
raise the front panel with the driver slightly.

6
8. Loosen 8 screws and remove the housing A.
9. Loosen 2 screws and remove the module assembly with
rechargeable battery first, then remove the motor holder.

7
4.2. Assembly Instructions
For assembly, reverse the order of disassembly.
1. Insert the rechargeable battery into the battery holder.
NOTE:
Make sure to attach the washer and O-ring to the bat-
tery terminal. The O-ring for the battery terminal is the
thickest. Confirm if the O-ring is attached properly.
• Battery terminal : washer x 1and O-ring x 1
• terminal pins: o-ring x 1
2. Set the motor holder first, then set the module assembly
with rechargeable battery.
NOTE:
Make sure that two motor lead wires are set within the
space between the battery holder and the motor
holder to prevent pinching.
NOTE:
Make sure to attach the switch cam with the lowest
position.
Apply the grease (G741S) on the housing O-ring.
3. Fix the motor holder in housing A with two screws.
NOTE:
Make sure that two O-rings are set.
4. Set the front panel.
NOTE:
Hook the bottom side first and fix the front panel.
Make sure to set the switch handle to the "0" position.
5. Set the click spring.

8
6. Set the housing C.
NOTE:
Make sure to set the rack.
Insert the hook of housing C under the front panel
first.
7. Fix the dial and the dial mounting base by a screw.
NOTE:
Make sure to set the slit at left side.
Apply the grease (G741S) on the gear of dial.
5 Wiring Connection Diagram

9
6 Schematic Diagram

Model No. : ER-GB50 Exploded View
7 Exploded View and Replacement Parts List

Model No. : ER-GB50 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 WERGB50K7458 COMB ATTACHMENT 1 (1-20mm)
2 WERGB50K7468 DETAIL TRIMMING ATTACHMENT 1
3 WER9605Y BLADE BLOCK 1
4 WERGB50S3108 DIAL COVER 1
5 WES7023L9008 TAPPING SCREW 1 (M2-6)
6 WER217D1477 DIAL MOUNTING BASE 1
7 WERGB50K3338 DIAL 1
8 WES631W6057 SCREW 11 (K2-8)
9 WERGB50K3028 HOUSING C 1
10 WERGB50K3858 FRONT PANEL 1
11 WERGC70L0288 RACK 1
12 WER223L0457 CLICK SPRING 1
13 WERGB50K3058 HOUSING A 1
14 WER217L1678 SWITCH CAM 1
15 WES7025L9707 SCREW 2 (K2-15)
16 WER217L0967 O-RING 2 (6PCS/PK)
17 WER217L3577 MOTOR HOLDER 1
18 WER217L1008 MOTOR 1
19 WERGB50L2108 MODULE ASSEMBLY 1
20 WER217L0977 O-RING 2 (2PCS/PK)
21 WES8017L2500 RECHARGEABLE BATTERY 1 (2PCS/PK), (NI-MH TYPE)
22 WER217L0318 CUSHION 1 (2PCS/PK)
23 WES7025L0977 O-RING AND WASHER 1 (2PCS/PK)
24 WERGB50K3068 HOUSING B 1
25 WER504L0167 SPRING FOR CUTTER 2 (2PCS/PK)
26 WERGB50K7663 ADAPTOR 1 (C-2 PLUG)
26 WERGB50K7675 ADAPTOR 1 (BF-3 PLUG)
27 WER203X7918 OIL 1
28 WES76806761 CLEANING BRUSH 1
29 WER217K7007 SOFT CASE 1
- WERGB50K8008 INDIVIDUAL BOX 1
- WERGB50K8009 INDIVIDUAL BOX 1 (Only for Saudi Arabia)
- WERGB50K8108 OPERATING INSTRUCTIONS 1