Panasonic WH-UD07HE5 User manual

© Panasonic Corporation 2016.
Order No: PAPAMY1603036CE
Indoor Unit Outdoor Unit
WH-SDC07H3E5
WH-SDC09H3E5
WH-UD07HE5
WH-UD09HE5
Destination
Europe
PRECAUTION OF LOW TEMPERATURE
In order to avoid frostbite, be assured of no refrigerant leakage during the installation or repairing of refrigerant circuit.
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the products dealt with in this service information by anyone else could result in serious injury or death.

2
TABLE OF CONTENTS
1.Safety Precautions ............................................. 4
2.Specifications ..................................................... 7
2.1WH-SDC07H3E5 WH-UD07HE5 ................... 7
2.2WH-SDC09H3E5 WH-UD09HE5 ................. 10
3.Features ............................................................. 13
4.Location of Controls and Components .......... 14
4.1Indoor Unit ................................................... 14
4.2Outdoor Unit ................................................. 37
5.Dimensions ....................................................... 38
5.1Indoor Unit ................................................... 38
5.2Outdoor Unit ................................................. 39
6.Refrigeration and Water Cycle Diagram ........ 40
6.1Standard System (Optional PCB not
connected) ................................................... 41
6.2Advance System (Optional PCB connected) ...
.................................................................... 41
7.Block Diagram .................................................. 42
8.Wiring Connection Diagram ............................ 43
8.1Indoor Unit ................................................... 43
8.2Outdoor Unit ................................................. 44
9.Electronic Circuit Diagram .............................. 45
9.1Indoor Unit ................................................... 45
9.2Outdoor Unit ................................................. 46
10.Printed Circuit Board ....................................... 47
10.1Indoor Unit ................................................... 47
10.2Outdoor Unit ................................................. 49
11.Installation Instruction ..................................... 51
11.1Indoor Unit ................................................... 51
11.2Variation of system ...................................... 58
11.3System Installation ....................................... 69
11.4Outdoor Unit ................................................. 80
12.Operation and Control ..................................... 85
12.1Basic Function ............................................. 85
12.2Water Pump ................................................. 98
12.3Indoor Unit Safety ......................................102
12.4Auto Restart Control ..................................102
12.5Indication Panel .........................................102
12.6Indoor Back-Up Heater Control .................103
12.7Tank Heater Control ...................................105
12.8Base Pan Heater Control (Optional) ..........107
12.9Heater Turn ON/OFF priority Control .........107
12.10Force Heater Mode ....................................108
12.11Powerful Operation ....................................109
12.12Quiet Operation ..........................................109
12.13Sterilization Mode ......................................110
12.14Outdoor Ambient Thermo OFF Control .....111
12.15Alternative Outdoor Ambient Sensor Control ..
..................................................................112
12.16Force DHW mode ......................................112
12.17Anti Freeze Control ....................................113
12.18Solar Operation (Optional) .........................114
12.19Boiler Bivalent Control .............................. 116
12.20External Room Thermostat Control (Optional)
................................................................. 118
12.21Three Ways Valve Control ........................ 119
12.22Two Ways Valve Control........................... 119
12.23External OFF/ON Control ......................... 120
12.24External Compressor Switch (Optional PCB) ..
................................................................. 121
12.25Heat/Cool Switch (Optional PCB) ............. 122
12.26SG Ready Control (Optional PCB) ........... 123
12.27Demand Control (Optional PCB) .............. 125
12.28Holiday Mode ............................................ 126
12.29Dry Concrete ............................................. 126
12.30Flow Sensor .............................................. 126
13.Protection Control ......................................... 127
13.1Protection Control for All Operations ........ 127
13.2Protection Control for Heating Operation.. 129
13.3Protection Control for Cooling Operation .. 130
14.Servicing Mode .............................................. 131
14.1How to Take Out Front Plate .................... 131
14.2Test Run ................................................... 131
14.3Expansion Vessel Pre Pressure Checking 131
14.4Pump Down Procedures ........................... 132
14.5How To Adjust Pump Speed ..................... 133
14.6How To Adjust Pump Speed ..................... 134
14.7How To Unlock Cool Mode ....................... 135
14.8EEPROM Factory Default Data Setup
Procedure ................................................. 136
14.9Dry Concrete Setup .................................. 137
15.Maintenance Guide........................................ 139
15.1Maintenance for Water Filter Set .............. 140
16.Troubleshooting Guide ................................. 142
16.1Refrigeration Cycle System ...................... 142
16.2Relationship between the Condition of the Air-
to-Water Heatpump Indoor and Outdoor Units
and Pressure and Electric Current ............ 143
16.3Breakdown Self Diagnosis Function ......... 144
16.4Error Codes Table ..................................... 146
16.5Self-diagnosis Method .............................. 148
17.Disassembly and Assembly Instructions ... 194
17.1To Remove Front Plate ............................. 194
17.2To Remove Pressure Gauge .................... 194
17.3To Open Control Board Cover .................. 195
17.4To Remove Control Panel ........................ 195
17.5To Remove RCCB .................................... 196
17.6To Remove Transformer and Electronic
Controller Board ........................................ 196
17.7To Open Control Board ............................. 197
17.8To Remove Pressure Relief Valve, Air Purge
Valve and Flow Sensor ............................. 197
17.9To Remove Water Pump and Bottle Complete
................................................................. 198
17.10To Remove Filter ...................................... 199
18.Technical Data ............................................... 200
18.1Operation Characteristics ......................... 200
18.2Heating Capacity Table............................. 212

3
18.3Cooling Capacity Table ............................. 212
19.Exploded View and Replacement Parts List 213
19.1Indoor Unit ................................................. 213
19.2Outdoor Unit .............................................. 215

4
1. Safety Precautions
 Read the following “SAFETY PRECAUTIONS” carefully before installation.
 Electrical work must be installed by a licensed electrician. Be sure to use the correct rating and main circuit for
the model to be installed.
 The caution items stated here must be followed because these important contents are related to safety. The
meaning of each indication used is as below. Incorrect installation due to ignoring of the instruction will cause
harm or damage, and the seriousness is classified by the following indications.
 Please leave this installation manual with the unit after installation.
WARNING This indication shows the possibility of causing death or serious injury.
CAUTION This indication shows the possibility of causing injury or damage to properties only.
 The items to be followed are classified by the symbols:
Symbol with white background denotes item that is PROHIBITED from doing.
Symbol with dark background denotes item that must be carried out.
 Carry out test run to confirm that no abnormality occurs after the installation. Then, explain to user the operation, care and
maintenance as stated in instructions. Please remind the customer to keep the operating instructions for future reference.
WARNING
1. Do not use unspecified cord, modified cord, joint cord or extension cord for power supply cord. Do not share the single outlet with
other electrical appliances. Poor contact, poor insulation or over current will cause electrical shock or fire.
2. Do not tie up the power supply cord into a bundle by band. Abnormal temperature rise on power supply cord may happen.
3. Keep plastic bag (packaging material) away from small children, it may cause suffocation.
4. Do not use pipe wrench to install refrigerant piping. It might deform the piping and cause the unit to malfunction.
5. Do not purchase unauthorized electrical parts for installation, service, maintenance and etc.. They might cause electrical shock or fire.
6. Do not modify the wiring of Indoor Unit for installation of other components (i.e. heater, etc). Overloaded wiring or wire connection
points may cause electrical shock or fire.
7. Do not add or replace refrigerant other than specified type. It may cause product damage, burst and injury etc.
8.
Do not use joint cable for Indoor / Outdoor Unit connection cable. Use specified Indoor / Outdoor Unit connection cable, refer to
instruction CONNECT THE CABLE TO THE INDOOR UNIT and connect tightly for Indoor / Outdoor Unit connection. Clamp the cable
so that no external force will be acted on the terminal. If connection or fixing is not perfect, it will cause heat up or fire at the
connection.
9. For electrical work, follow local wiring standard, regulation and this installation instruction. An independent circuit and single outlet
must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will cause electrical shock or fire.
10. For water circuit installation work, follow to relevant European and national regulations (including EN61770) and local plumbing and
building regulation codes.
11. Engage dealer or specialist for installation. If installation done by the user is defective, it will cause water leakage, electrical shock or
fire.
12.
 This is a R410A model, when connecting the piping, do not use any existing (R22) pipes and flare nuts. Using such same may
cause abnormally high pressure in the refrigeration cycle (piping), and possibly result in explosion and injury. Use only R410A
refrigerant.
 Thickness or copper pipes used with R410A must be 0.8 mm or more. Never use copper pipes thinner than 0.8 mm.
 It is desirable that the amount of residual oil is less than 40mg/10m.
13. When install or relocate Indoor Unit, do not let any substance other than the specified refrigerant, e.g. air etc. mix into refrigerant cycle
(piping). Mixing of air etc. will cause abnormal high pressure in refrigeration cycle and result in explosion, injury etc..
14. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical shock or fire.
15. Install at a strong and firm location which is able to withstand the set’s weight. If the strength is not enough or installation is not
properly done, the set will drop and cause injury.
16. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical shock or fire.

5
WARNING
17. Install at a strong and firm location which is able to withstand the set’s weight. If the strength is not enough or installation is not
properly done, the set will drop and cause injury.
18. This equipment is strongly recommended to be installed with Residual Current Device (RCD) on-site according to the respective
national wiring rules or country–specific safety measures in terms of residual current.
19.
During installation, install the refrigerant piping properly before run the compressor. Operation of compressor without fixing
refrigeration piping and valves at opened condition will cause suck-in of air, abnormal high pressure in refrigeration cycle and result in
explosion, injury etc.
20.
During pump down operation, stop the compressor before remove the refrigeration piping. Removal of refrigerant piping while
compressor is operating and valves are opened will cause suck-in of air, abnormal high pressure in refrigerant cycle and result in
explosion, injury etc.
21. Tighten the flare nut with torque wrench according to specified method. If the flare nut is over tightened, after a long period, the flare
may break and cause refrigerant gas leakage.
22. After completion of installation, confirm there is no leakage of refrigerant gas. It may generate toxic gas when the refrigerant contacts
with fire.
23. Ventilate the room if there is refrigerant gas leakage during operation. Extinguish all fire sources if present. It may cause toxic gas
when the refrigerant contacts with fire.
24. Only use the supplied or specified installation parts, else, it may cause unit vibrate loose, water leakage, electrical shock or fire.
25. The unit is only for use in closed water system. Utilization in an open water circuit may lead to excessive corrosion of water piping and
risk of incubating bacteria colonies, particularly Legionella, in water.
26. If there is any doubt about the installation procedure or operation, always contact the authorized dealer for advice and information.
27. Select a location where in case of water leakage, the leakage will not cause damage to other properties.
28. When installing electrical equipment at wooden building of metal lath or wire lath, in accordance with electrical facility standard, no
electrical contact between equipment and building is allowed. Insulator must be installed in between.
29. Any work carried out on the Indoor Unit after removing any panels which is secured by screws, must be carried out under the
supervision of authorized dealer and licensed installation contractor.
30.
This unit must be properly earthed. The electrical earth must not be connected to a gas pipe, water pipe, the earth of lightening rod or
a telephone. Otherwise there is a danger of electrical shock in the event of an insulation breakdown or electrical earth fault in the
outdoor unit.
CAUTION
1. Do not install the Indoor Unit at place where leakage of flammable gas may occur. In case gas leaks and accumulates at surrounding
of the unit, it may cause fire.
2. Do not release refrigerant during piping work for installation, re-installation and during repairing a refrigeration parts. Take care of the
liquid refrigerant, it may cause frostbite.
3. Do not install this appliance in a laundry room or other high humidity location. This condition will cause rust and damage to the unit.
4. Make sure the insulation of power supply cord does not contact hot part (i.e. refrigerant piping) to prevent from insulation failure (melt).
5. Do not apply excessive force to water pipes that may damage the pipes. If water leakage occurs, it will cause flooding and damage to
other properties.
6. Select an installation location which is easy for maintenance.
7. Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water may enter the room and damage
the furniture.
8.
Power supply connection to Indoor Unit.
 Power supply point should be in easily accessible place for power disconnection in case of emergency.
 Must follow local national wiring standard, regulation and this installation instruction.
 Strongly recommended to make permanent connection to a circuit breaker.
- Power supply 1: Use approved 30A 2-poles circuit breaker with a minimum contact gap of 3.0 mm.
- Power supply 2: Use approved 30A 2-poles circuit breaker with a minimum contact gap of 3.0 mm.
9. Ensure the correct polarity is maintained throughout all wiring. Otherwise, it will cause electrical shock or fire.
10. After installation, check the water leakage condition in connection area during test run. If leakage occurs, it will cause damage to other
properties.

6
CAUTION
12.
Installation work.
It may need two or more people to carry out the installation work. The weight of Indoor Unit might cause injury if carried by one
person.

7
2. Specifications
2.1 WH-SDC07H3E5 WH-UD07HE5
Item Unit Outdoor Unit
Performance Test Condition EN 14511
Cooling Capacity
Condition
(Ambient/Water) A35W7
kW 6.00
BTU/h 20500
kcal/h 5160
Cooling EER W/W 2.63
kcal/hW 2.26
Heating Capacity
Condition
(Ambient/Water) A7W35 A2W35
kW 7.00 6.55
BTU/h 23900 22300
kcal/h 6020 5630
Heating COP W/W 4.46 3.34
kcal/hW 3.84 2.87
Heating ErP
Low Temperature Application (W35) Warmer Average Colder
Application Climate
Pdesign kW 7.0 5.0 6.0
Tbivalent / TOL °C 2 / 2 -10 / -10 -15 / -22
SCOP / ns (W/W) / % 5.69 / 225 4.83 / 190 4.08 / 160
Annual Consumption kWh 1643 2140 3624
Class A++ A++ A++
Medium Temperature Application (W55) Warmer Average Colder
Application Climate
Pdesign kW 6.0 7.0 6.0
Tbivalent / TOL °C 2 / 2 -6 / -10 -15 / -22
SCOP / ns (W/W) / % 4.07 / 160 3.32 / 130 2.95 / 115
Annual Consumption kWh 1971 4354 5022
Class A++ A++ A+
Noise Level
Condition
(Ambient/Water) A35W7 A7W35 A2W35
dB (A) Cooling: 48 Heating: 50 —
Power Level dB Cooling: 66 Heating: 68 —
Air Flow m3/min (ft3/min) Cooling: 56.3 (1987)
Heating: 46.0 (1624)
Refrigeration Control Device Expansion Valve
Refrigeration Oil cm3 FV50S (900)
Refrigerant (R410A) kg (oz) 1.45 (51.2)
Dimension
Height mm (inch) 795 (31-5/16)
Width mm (inch) 900 (35-7/16)
Depth mm (inch) 320 (12-19/32)
Net Weight kg (lbs) 66 (146)
Pipe Diameter Liquid mm (inch) 6.35 (1/4)
Gas mm (inch) 15.88 (5/8)
Standard Length m (ft) 7 (23.0)
Pipe Length Range m (ft) 3 (9.8) ~ 30 (98.4)
I/D & O/D Height Difference m (ft) 20 (65.6)
Additional Gas Amount g/m (oz/ft) 30 (0.3)
Refrigeration Charge Less m (ft) 10 (32.8)

8
Item Unit Outdoor Unit
Compressor
Type Hermetic Motor
Motor Type Brushless (4-poles)
Rated Output kW 1.70
Fan
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W —
Output Power W 60
Fan Speed rpm Cooling: 670
Heating: 570
Heat Exchanger
Fin material Aluminium (Pre Coat)
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 30 × 17
Size (W × H × L) mm 38.1 × 762.0 × 873.8:903.8
Power Source (Phase, Voltage, Cycle)
ø Single
V 230
Hz 50
Input Power
Condition
(Ambient/Water) A35W7 A7W35 A2W35
kW Cooling: 2.28 Heating: 1.57 Heating: 1.96
Maximum Input Power For Heatpump System kW 4.59
Power Supply 1 : Phase (Ø) / Max. Current (A) / Max. Input Power (W) 1Ø / 21.0 / 4.59k
Power Supply 2 : Phase (Ø) / Max. Current (A) / Max. Input Power (W) 1Ø / 13.0 / 3.00k
Power Supply 3 : Phase (Ø) / Max. Current (A) / Max. Input Power (W) — / — / —
Starting Current A 7.2
Running Current
Condition
(Ambient/Water) A35W7 A7W35 A2W35
A Cooling: 10.3 Heating: 7.2 Heating: 9.0
Maximum Current For Heatpump System A 21.0
Power Factor
Power factor means total figure of compressor and
outdoor fan motor.
% Cooling: 96
Heating: 95
Power Cord Number of core —
Length m (ft) —
Thermostat Electronic Control
Protection Device Electronic Control
Item Unit Indoor Unit
Performance Test Condition EN 14511
Operation Range
Outdoor Ambient °C Cooling: 16 ~ 43
Heating: -20 ~ 35
Water Outlet °C Cooling: 5 ~ 20
Heating: 20 ~ 55
Internal Pressure Differential kPa Cooling: 18.0
Heating: 24.0
Noise Level
Condition
(Ambient/Water) A35W7 A7W35 A2W35
dB (A) Cooling: 30 Cooling: 30 —
Power Level dB Cooling: 43 Cooling: 43 —
Dimension
Height mm (inch) 892 (35-1/8)
Width mm (inch) 500 (19-11/16)
Depth mm (inch) 340 (13-13/32)
Net Weight kg (lbs) 44 (97)
Refrigerant Pipe Diameter Liquid mm (inch) 6.35 (1/4)
Gas mm (inch) 15.88 (5/8)
Water Pipe Diameter Inlet mm (inch) 28 (1-3/32)
Outlet mm (inch) 28 (1-3/32)
Water Drain Hose Inner Diameter mm (inch) 12 (15/32)

9
Item Unit Indoor Unit
Pump
Motor Type DC Motor
No. of Speed 7 (Software Selection)
Input Power W 48
Hot Water Coil
Type Brazed Plate
No. of Plates 48
Size (H × W × L) mm 82 × 93 × 325
Water Flow Rate l/min (m3/h) Cooling: 17.6 (1.1)
Heating: 20.1 (1.2)
Pressure Relief Valve Water Circuit kPa Open: 300, Close: 266 and below
Flow Switch Electronic Sensor
Protection Device A Residual Current Circuit Breaker (30 ~ 40)
Expansion Vessel Volume I 10
MWP bar 3
Capacity of Integrated Electric Heater kW 3.00
Note:
 Cooling capacities are based on outdoor air temperature of 35°C Dry Bulb with controlled indoor water inlet
temperature of 12°C and water outlet temperature of 7°C.
 Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled indoor water inlet temperature of 30°C and water outlet temperature of 35°C.
 Specification are subjected to change without prior notice for further improvement.
 Flow rate indicated are based on nominal capacity adjustment of leaving water temperature (LWT) 35°C and ∆T
= 5°C.

10
2.2 WH-SDC09H3E5 WH-UD09HE5
Item Unit Outdoor Unit
Performance Test Condition EN 14511
Cooling Capacity
Condition
(Ambient/Water) A35W7
kW 7.00
BTU/h 23900
kcal/h 6020
Cooling EER W/W 2.43
kcal/hW 2.09
Heating Capacity
Condition
(Ambient/Water) A7W35 A2W35
kW 9.00 6.70
BTU/h 30700 22800
kcal/h 7740 5760
Heating COP W/W 4.13 3.13
kcal/hW 3.55 2.69
Heating ErP
Low Temperature Application (W35) Warmer Average Colder
Application Climate
Pdesign kW 7.0 6.0 7.0
Tbivalent / TOL °C 2 / 2 -10 / -10 -15 / -22
SCOP / ns (W/W) / % 5.69 / 225 4.83 / 190 4.08 / 160
Annual Consumption kWh 1643 2566 4233
Class A++ A++ A++
Medium Temperature Application (W55) Warmer Average Colder
Application Climate
Pdesign kW 6.0 7.0 6.0
Tbivalent / TOL °C 2 / 2 -6 / -10 -15 / -22
SCOP / ns (W/W) / % 4.07 / 160 3.32 / 130 2.95 / 115
Annual Consumption kWh 1971 4354 5022
Class A++ A++ A+
Noise Level
Condition
(Ambient/Water) A35W7 A7W35 A2W35
dB (A) Cooling: 50 Heating: 51 —
Power Level dB Cooling: 68 Heating: 69 —
Air Flow m3/min (ft3/min) Cooling: 56.3 (1987)
Heating: 51.0 (1800)
Refrigeration Control Device Expansion Valve
Refrigeration Oil cm3 FV50S (900)
Refrigerant (R410A) kg (oz) 1.45 (51.2)
Dimension
Height mm (inch) 795 (31-5/16)
Width mm (inch) 900 (35-7/16)
Depth mm (inch) 320 (12-19/32)
Net Weight kg (lbs) 66 (146)
Pipe Diameter Liquid mm (inch) 6.35 (1/4)
Gas mm (inch) 15.88 (5/8)
Standard Length m (ft) 7 (23.0)
Pipe Length Range m (ft) 3 (9.8) ~ 30 (98.4)
I/D & O/D Height Difference m (ft) 20 (65.6)
Additional Gas Amount g/m (oz/ft) 30 (0.3)
Refrigeration Charge Less m (ft) 10 (32.8)
Compressor
Type Hermetic Motor
Motor Type Brushless (4-poles)
Rated Output kW 1.70

11
Item Unit Outdoor Unit
Fan
Type Propeller Fan
Material PP
Motor Type DC (8-poles)
Input Power W —
Output Power W 60
Fan Speed rpm Cooling: 700
Heating: 640
Heat Exchanger
Fin material Aluminium (Pre Coat)
Fin Type Corrugated Fin
Row × Stage × FPI 2 × 30 × 17
Size (W × H × L) mm 38.1 × 762.0 × 873.8:903.8
Power Source (Phase, Voltage, Cycle)
ø Single
V 230
Hz 50
Input Power
Condition
(Ambient/Water) A35W7 A7W35 A2W35
kW Cooling: 2.88 Heating: 2.18 Heating: 2.14
Maximum Input Power For Heatpump System kW 5.01
Power Supply 1 : Phase (Ø) / Max. Current (A) / Max. Input Power (W) 1Ø / 22.9 / 5.01k
Power Supply 2 : Phase (Ø) / Max. Current (A) / Max. Input Power (W) 1Ø / 13.0 / 3.00k
Power Supply 3 : Phase (Ø) / Max. Current (A) / Max. Input Power (W) — / — / —
Starting Current A 10.0
Running Current
Condition
(Ambient/Water) A35W7 A7W35 A2W35
A Cooling: 13.0 Heating: 10.0 Heating: 9.8
Maximum Current For Heatpump System A 22.9
Power Factor
Power factor means total figure of compressor and
outdoor fan motor.
% Cooling: 96
Heating: 95
Power Cord Number of core —
Length m (ft) —
Thermostat Electronic Control
Protection Device Electronic Control
Item Unit Indoor Unit
Performance Test Condition EN 14511
Operation Range
Outdoor Ambient °C Cooling: 16 ~ 43
Heating: -20 ~ 35
Water Outlet °C Cooling: 5 ~ 20
Heating: 20 ~ 55
Internal Pressure Differential kPa Cooling: 24.0
Heating: 39.5
Noise Level
Condition
(Ambient/Water) A35W7 A7W35 A2W35
dB (A) Cooling: 30 Cooling: 30 —
Power Level dB Cooling: 43 Cooling: 43 —
Dimension
Height mm (inch) 892 (35-1/8)
Width mm (inch) 500 (19-11/16)
Depth mm (inch) 340 (13-13/32)
Net Weight kg (lbs) 44 (97)
Refrigerant Pipe Diameter Liquid mm (inch) 6.35 (1/4)
Gas mm (inch) 15.88 (5/8)
Water Pipe Diameter Inlet mm (inch) 28 (1-3/32)
Outlet mm (inch) 28 (1-3/32)
Water Drain Hose Inner Diameter mm (inch) 12 (15/32)
Pump
Motor Type DC Motor
No. of Speed 7 (Software Selection)
Input Power W 68

12
Item Unit Indoor Unit
Hot Water Coil
Type Brazed Plate
No. of Plates 48
Size (H × W × L) mm 82 × 93 × 325
Water Flow Rate l/min (m3/h) Cooling: 20.1 (1.2)
Heating: 25.8 (1.5)
Pressure Relief Valve Water Circuit kPa Open: 300, Close: 266 and below
Flow Switch Electronic Sensor
Protection Device A Residual Current Circuit Breaker (30 ~ 40)
Expansion Vessel Volume I 10
MWP bar 3
Capacity of Integrated Electric Heater kW 3.00
Note:
 Cooling capacities are based on outdoor air temperature of 35°C Dry Bulb with controlled indoor water inlet
temperature of 12°C and water outlet temperature of 7°C.
 Heating capacities are based on outdoor air temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb
(42.8°F Wet Bulb) with controlled indoor water inlet temperature of 30°C and water outlet temperature of 35°C.
 Specification are subjected to change without prior notice for further improvement.
 Flow rate indicated are based on nominal capacity adjustment of leaving water temperature (LWT) 35°C and ∆T
= 5°C.

13
3. Features
 Inverter Technology
- Energy saving
 High Efficiency
 Compact Design
 Environment Protection
- Non-ozone depletion substances refrigerant (R410A)
 Long Installation Piping
- Long piping up to 15 meter with height difference 5 meter
- Flexible 4-way piping for outdoor unit
 Easy to use control panel
 Weekly Timer setting
 Quality Improvement
- Random auto restart after power failure for safety restart operation
- Gas leakage protection
- Prevent compressor reverse cycle
- Inner protector to protect compressor
 Serviceability Improvement
- Breakdown Self Diagnosis function
- System Status Check Buttons for servicing purpose
- System Pumpdown Button for servicing purpose
- Front maintenance design for outdoor unit
 Operation Condition
Indoor Outdoor
Water outlet temperature (°C) Ambient temperature (°C)
COOLING Maximum 20 43
Minimum 5 16
HEATING Maximum 55 35
Minimum 20 -20
NOTICE : When the outdoor temperature is out of the above temperature range, the heating capacity will drop significantly
and outdoor unit might stop for protection control.

14
4. Location of Controls and Components
4.1 Indoor Unit
4.1.1 Location of Control
Buttons / Indicator
Water pressure gauge
• Do not press or hit the glass cover using hard
and sharp objects. Failure to do so may cause
damage to the unit.
• Ensure that the water pressure is between 0.05
and 0.3 MPa (0.1 MPa = 1 bar).
• In case the water pressure is out of the above
range, consult an authorised dealer.
1
Quick Menu button
(For more details, refer to the separate
Quick Menu Guide.)
2Back button
Returns to the previous screen
3LCD Display
4Main Menu button
For function setup
5ON/OFF button
Starts/Stops operation
6
Operation indicator
Illuminates during operation, blinks during
alarm.
Press centre
No glove
No pen
2
1
4
5
6
3
Cross key buttons
Selects an item.
Enter button
Fixes the selected content.
Up
Down
thgiRtfeL
0.2
0.4
0.30.1
MPa
bar
2
31
4
23
1
44 40
10:34am, Mon
18
˚
c
˚
c
˚
c
˚
c
2

15
Display
1Mode selection
AUTO •Depending on the preset outdoor
temperature, the system selects
HEAT or *
1
COOL operation mode.
Auto Heat Auto Cool
*
1,
*
2
COOL •The fan coil unit is either turned
ON or OFF.
•The outdoor unit provides cooling
to the system.
AUTO
+ TANK
•Depending on the preset outdoor
temperature, the system selects
HEAT + TANK or *
1
COOL + TANK
operation mode.
Auto Heat Auto Cool
*
1,
*
2
COOL
+ TANK
•The outdoor unit provides cooling
to the system.
•The system controls the booster
heater in the water tank.
HEAT •The panel/floor HEAT operation is
either turned ON or OFF.
•The outdoor unit provides heat to
the system.
TANK •The water tank is either turned
ON or OFF.
•The outdoor unit provides heat to
the water tank.
HEAT
+ TANK
•The outdoor unit provides heat to
the water tank and the system.
•This mode can be selected only
when the water tank is installed.
* The direction icons point to the currently
active mode.
•Room operation / Tank operation.
•Deice operation.
2Operation icons
The status of operation is displayed.
Icon will not display (under operation OFF screen) whenever operation is OFF except weekly timer.
Holiday operation status Weekly Timer operation status Quiet operation status
Zone:Room Thermostat
→Internal sensor status Powerful operation status Demand Control or SG ready or SHP status
Room Heater status Tank Heater status Solar status
Bivalent status
(Boiler)
*1 The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised service partners.
*2 Only displayed when COOL mode is unlocked (This means when COOL mode is available).
3Temperature of each zone
4Time and day
5Water Tank temperature
6Outdoor temperature
7Sensor type/Set temperature type icons
Water Temperature
→Compensation curve
Water Temperature
→Direct Pool only
Room Thermostat
→External
Room Thermostat
→Internal
2 4
1
5
6
7
23
1
44
40
10:34am, Mon
18
˚
c
˚
c
˚
c
˚
c
2
3

16
4.1.2 Initialization
Before starting to install the various menu settings, please initiate the Remote Controller by selecting the language of
operation and installing the date and time correctly.
It is recommended that the installer conducts the following initialization of the Remote Controller.
Selecting the language
LCD blinking
Press and wait while the display is
initializing.
1Scroll with and to select the language.
2Press to confirm the selection.
Setting the clock
1htiwtceleS or how to display the time,
either 24h or am/pm format (for example, 15:00
or 3 pm).
2Press to confirm the selection.
3Use and to select year, month, day,
hour and minutes. (Press to confirm the
selection each time.)
4Once the time is set, time and day will appear
on the display even if the Remote Controller is
turned OFF.
4.1.3 Quick Menu
A
fter the initial settings have been completed, you can select a quick menu from the following options and edit the setting.
1Press to display the quick menu.
Force DHW Powerful Quiet Force Heater
Timer Force Defrost Error Reset R/C Lock
2Use to select menu.
3Press to turn on/off the select menu.
Select ON/OFF

17
4.1.3.1 Before Use
This Quick Guide explains how to use the Quick Menu.
Please read the Operating Instructions thoroughly before using the Quick Menu.
4.1.3.2 How to use the Quick Menu
After the initial settings have been completed, you can select a quick menu from the
following options and edit the setting.
Select each setting and confirm the setting
according to the instructions displayed at the
bottom of the screen. (The icons refer to each
selection key.)
Quick Menu
To return to the Main Screen,
Press or .
Force DHW Powerful Quiet Force
Heater
Weekly
Timer
Force
Defrost Error Reset R/C Lock
■ Note:
• If the system is not
connected to the tank
(Tank Connection is
OFF), the Quick Menu
screen will be displayed
as right. Make sure the
Tank Connection is ON.
1Press . 2Use to select menu.
3Press to turn on/off the select
menu.
Select Change
Select ON/OFF
Select ON/OFF
23
1
44
40
10:34am, Mon
18
˚c
˚c
˚c
˚c
2

18
Notes on operation icon
Example:
• Operation icon indicate with “ ” = OFF
• Operation icon indicate with “ ” = ON
Select this icon to turn the Tank DHW on or off.
Press to confirm your selection.
• Force DHW is turned off.
• Force DHW is turned on.
■ Note:
• Force DHW is disabled when Force Heater is turned on.
• When Force DHW is turned off, operation & mode should change back to
the previous memorized status.
Force DHW
Select this icon to operate the heating/cooling system
powerfully.
Press to confirm your selection.
(The powerful operation starts approximately 1 minute after is
pressed.)
• Powerful mode is set off.
• The Powerful mode operates for 30 minutes.
• The Powerful mode operates for 60 minutes.
• The Powerful mode operates for 90 minutes.
■ Note:
• Powerful is disabled when operation is turned OFF.
Powerful
30
60
90

19
Select this icon to operate quietly.
Press to confirm your selection.
(The quiet operation starts approximately 1 minute after is pressed.)
• Quiet mode is set off.
• The Quiet mode operates at level 1.
• The Quiet mode operates at level 2.
• The Quiet mode operates at level 3.
Level 3 is the most quiet mode.
• Select this to set a timer for the Quiet mode operation.
After 1 sec delay.
Quiet
Select “Yes”.
• Select “Yes” using buttons.
Select pattern “1” ~ “6”.
Select “Edit”.
• If you select “Delete”, the timer setting of
the selected pattern will be deleted.
Set the hour and minutes.
Select the level of Quiet.
■Note:
• If the time overlaps with another pattern,
"Set time is overlapped!" will appear on
the screen.
1
2
3

20
Select to force the Heater on.
Press to confirm your selection.
(The Force Heater mode starts approximately 1 minute after is
pressed.)
• Force Heater is turned off.
• Force Heater is turned on.
■Note:
• Force Heater is disabled whenever
operation is already on and ‘Disabled
due to Operation ON!’ will be
displayed.
Force
Heater