Panasonic WHUD30BE51 User manual

F567459
HEAT
SETTING
STATUS
PUMPDW
WATERINLET ERROR
OFF/ON
WATEROUTLET OUTDOOR
C
C
C
0.2
0.4
0
0.3
0.1
MPa
Operating Instructions
Air-to-Water Heatpump
Model No.
Indoor Unit Outdoor Unit
WH-SD24BE5-1 WH-UD24BE5-1
WH-SD30BE5-1 WH-UD30BE5-1
ENGLISH
ENGLISH
Before operating the unit, read these operating instructions thoroughly and keep them for future reference.
Before operating the unit, read these operating instructions thoroughly and keep them for future reference.
Before operating the unit, make sure the installation has been carried out correctly by authorized dealer correctly and
precisely following the installation instructions given.
2 ~ 9
2 ~ 9
SVENSKA
SVENSKA
Innan du använder enheten, läs noga igenom denna bruksanvisning och spara den för framtida bruk.
Innan du använder enheten, läs noga igenom denna bruksanvisning och spara den för framtida bruk.
Innan du använder enheten, se till att installationen har utförts noggrant och korrekt av auktoriserad återförsäljare som
följt de givna installationsinstruktionerna.
10 ~ 17
10 ~ 17
NORSK
NORSK
Les bruksanvisningen nøye før du bruker denne enheten, og oppbevar den for fremtidig bruk.
Les bruksanvisningen nøye før du bruker denne enheten, og oppbevar den for fremtidig bruk.
Før du bruker enheten, må du forsikre deg om at autorisert forhandler har utført korrekt og presis installasjon og har
fulgt installasjonsinstruksjonene som er gitt.
18 ~ 25
18 ~ 25
SUOMI
SUOMI
Lue nämä käyttöohjeet huolellisesti ennen yksikön käyttämistä ja säilytä ne tulevaisuutta varten.
Lue nämä käyttöohjeet huolellisesti ennen yksikön käyttämistä ja säilytä ne tulevaisuutta varten.
Varmista ennen laitteen käyttöä, että asennuksen on suorittanut valtuutettu jälleenmyyjä ja että se on tehty oikein ja
Varmista ennen laitteen käyttöä, että asennuksen on suorittanut valtuutettu jälleenmyyjä ja että se on tehty oikein ja
tarkasti annettuja asennusohjeita noudattaen.
tarkasti annettuja asennusohjeita noudattaen.
26 ~ 33
26 ~ 33
DANSK
DANSK
Læs brugsanvisningen grundigt igennem før du benytter anlægget og gem den til fremtidig brug.
Læs brugsanvisningen grundigt igennem før du benytter anlægget og gem den til fremtidig brug.
Sørg for, at anlægget er installeret korrekt af en autoriseret forhandler i overensstemmelse med de følgende
instruktioner, før anlægget tages i brug.
34 ~ 41
34 ~ 41
© Panasonic HA Air-Conditioning (M) Sdn. Bhd. 2010.
Unauthorized copying and distribution is a violation
of law.
F567459_YS0111-2.indb 1F567459_YS0111-2.indb 1 23-Mar-11 11:23:18 AM23-Mar-11 11:23:18 AM

2
Thank you for purchasing
Panasonic Product
TABLE OF CONTENTS
TABLE OF CONTENTS
SAFETY PRECAUTIONS
2~3
PRODUCT OVERVIEW
4
BASIC OPERATION
5
ADVANCE OPERATION
6
CARE & CLEANING
7
TROUBLESHOOTING
8
INFORMATION
9
NOTE :
The illustrations in this manual are
for explanation purposes only and
may differ from the actual unit. It is
subjected to change without notice
for future improvement.
• Panasonic Air-to-Water Heatpump is a split system consisting
only of an indoor unit and an outdoor unit. This system designed for
combination with Panasonic Tank Unit. In case of non-Panasonic
Tank Unit is being used with Panasonic Air-to-Water Heatpump
System, Panasonic cannot guarantee neither good operation nor
reliability of the system.
• This manual describes how to operate the Heatpump system
between indoor and outdoor units only.
• Other operation such as water tank, radiator and underfloor system,
please refer to respective manufacturer operation manuals.
OPERATION CONDITION
OPERATION CONDITION
Water outlet
Temperature (°C) Indoor
HEATING Max. 55
Min. 25
Ambient
Temperature (°C) Outdoor
HEATING Max. 35
Min. -20
NOTICE : When the outdoor temperature
is out of the above temperature
range, the heating capacity will
drop significantly and outdoor
unit might stop for protection
control.
To prevent personal injury, injury to others, or property damage, please
comply with the following.
Incorrect operation due to failure to follow instructions below may cause
harm or damage, the seriousness of which is classified as below:
WARNING
WARNING
This sign warns of death or serious injury.
CAUTION
CAUTION
This sign warns of injury or damage to
property.
The instructions to be followed are classified by the following symbols:
This symbol denotes an action that is
PROHIBITED.
These symbols denote an actions that
is COMPULSORY.
WARNING
WARNING
INDOOR UNIT AND OUTDOOR UNIT
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
Please consult authorized dealer or specialist to repair,
install, remove and reinstall the unit. Improper installation
and handling will cause leakage, electric shock or fire.
Do not install the unit in a potentially explosive or flammable
atmosphere. Failure to do so could result in fire.
Do not insert your fingers or other objects into the
indoor or outdoor unit, rotating parts may cause
injury.
Do not touch the outdoor unit during lightning, it may cause
electric shock.
Do not attempt to repair the unit by yourself. Otherwise,
it may cause injury if it is mishandling.
Do not install the indoor unit at outdoor. This is designed for
indoor installation only.
SAFETY PRECAUTIONSSAFETY PRECAUTIONS
F567459_YS0111-2.indb 2F567459_YS0111-2.indb 2 23-Mar-11 11:23:20 AM23-Mar-11 11:23:20 AM

3
ENGLISH
CAUTION
CAUTION
INDOOR UNIT AND OUTDOOR UNIT
Do not wash the indoor unit with water,
benzene, thinner or scouring powder.
Do not install the unit close to any combustible
equipment or at bathroom. Otherwise, it may
cause electric shock or fire.
Do not touch the water discharge pipe at the
indoor unit during operation.
Do not place anything on top or beneath of the
unit.
Do not sit or step on the unit, you
may fall down accidentally.
Do not touch the sharp aluminium fin,
sharp parts may cause injury.
Ensure drainage pipe is connected properly.
Otherwise, leakage may occur.
Check the installation rack periodically to make
sure that it is not damaged. After long periods
of use, the strength of the installation rack may
have deteriorated.
CONTROL PANEL
Do not let the control panel get wet. Otherwise,
it may cause electric shock or fire.
Do not press the buttons on the control panel
with hard, pointed objects. Otherwise, it may
damage the unit.
Do not wash the control panel with water,
benzene, thinner or scouring powder.
Do
not inspect or service the control panel by
not inspect or service the control panel by
yourself. Please consult authorized dealer.
yourself. Please consult authorized dealer.
Otherwise, it may cause injury if mishandling.
WARNING
WARNING
POWER SUPPLY
Do not use modified cord,
joint cord, extension cord or
unspecified cord to prevent
overheating and fire.
Do not share the same power outlet with other
equipment to prevent overheating and fire.
Do not operate with wet hands to prevent electric
shock.
If the supply cord is damage, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
This unit is equipped with Residue Current Circuit
Breaker (RCCB). It is strongly recommended to
check the operation of the RCCB after installation
and periodically after servicing or maintenance by
authorized dealer to ensure it is in good working
order. Otherwise, it may cause electrical shock or
fire in case of malfunction.
It is strongly recommended to install Residual
Current Device (RCD) on-site to prevent electric
shock or fire.
It is recommended to wear gloves during servicing
or maintenance in order to avoid hazard.
This equipment must be earthed to prevent
electrical shock or fire.
Prevent electric shock by switching off the power
supply when:
- Before cleaning or servicing.
- Extended non-use.
- Abnormally strong lightning activity.
This appliance is for multiple uses. All power
supply circuits must be turn off before access to
any of the terminals in the indoor unit, to avoid
electrical shock, burn or fatal injury.
Stop using the product when any abnormality/
failure occurs and disconnect the power plug
or turn off the power switch and breaker.
(Risk of smoke/fire/electric shock)
Examples of
abnormality/
failure
• The RCCB switches off by itself.
• Burning smell, abnormal noise or vibration
sound is observed when the unit is in use.
• Hot water keeps on coming off the unit.
Contact immediately your local dealer for
maintenance/repair.
/
/
Floor Heating
Panel
Control Panel
Power Supply
Water Tank Unit
Indoor Unit
Outdoor Unit
Shower
F567459_YS0111-2.indb 3F567459_YS0111-2.indb 3 23-Mar-11 11:23:20 AM23-Mar-11 11:23:20 AM

4
HEAT
SETTING
STATUS
PUMPDW
WATERINLET ERROR
OFF/ON
WATEROUTLET OUTDOOR
C
CC
0.2
0.40
0.30.1
MPa
PRODUCT OVERVIEWPRODUCT OVERVIEW
Air-to-Water Heatpump
Air-to-Water Heatpump
Indoor Unit
Indoor Unit
Water Pressure Gauge
Water Pressure Gauge
0.2
0.40
0.30.1
MPa
• Do not press or hit the glass
cover with hard, pointed
objects. This may damage the
unit.
• Ensure that the water
pressure is between 0.05 to
0.2 MPa (0.1 MPa = 1 bar).
• In case the water pressure is
out of the above range, please
consult authorized dealer.
Control Panel
Control Panel
HEAT
SETTING
STATUS
PUMPDW
WATER INLET ERROR
OFF /ON
WATER OUTLET OUTDOOR
C
C
C
Open the cover to
use the buttons
WATER OUTLET OUTDOOR
HEAT
SETTING
STATUS
PUMPDW
WATER INLET ERROR
C
CC
SET
SELECT
CANCEL
ERROR
RESET
SETTING STATUS
SEARCH
PUMPDW
CHECK
OFF /ON
11
2
1
12 13
8
10
9
14
7
5
4
36
1OFF/ON Button 8System Pumpdown Mode Indicator
2Operation LED 9System Status Check Mode Indicator
3System Setting Mode Buttons 10 System Setting Mode Indicator
4Error Reset Button 11 Heating Operation Indicator
5System Status Check Mode Buttons 12 Water Outlet Temperature Display
6System Pumpdown Mode Button 13 Water Inlet Temperature Display
7System Error Display 14 Outdoor Ambient Temperature Display
F567459_YS0111-2.indb 4F567459_YS0111-2.indb 4 23-Mar-11 11:23:21 AM23-Mar-11 11:23:21 AM

5
ENGLISH
BASIC OPERATIONBASIC OPERATION
WATER INLET ERROR
SET
SETTING STATUS
CHECK
OFF /ON
Operation Start / Stop
Operation Start / Stop
• The unit starts by pressing
OFF /ON
.
• When unit is ON, operation LED is lit and the actual
temperature for water outlet, water inlet and outdoor
ambient are shown on the control panel display.
• Press
OFF /ON
again to stop the operation.
Operation details (Default setting)
Operation details (Default setting)
• Operation takes place under default settings as follows:
-
-
When Outdoor ambient temperature (Out Lo) is less than 0°C, water outlet set temperature (H2O Lo) is 50°C.
When Outdoor ambient temperature (Out Hi) is more than 15°C, water outlet set temperature (H2O Hi) is 32°C.
• In between the specified outdoor ambient temperature range (Out Lo and Out Hi), the system will automatically adjust
the water outlet temperature between specified range (H2O Lo and H2O Hi).
• Lower outdoor ambient temperature will result in higher water outlet temperature and vice versa.
Optional Settings
Optional Settings
ERROR
RESET
Error code reset
• Not usable during normal operation.
PUMPDW
System Pump Down
• Not usable during normal operation.
• If accidentally pressed the
PUMPDW
, press
OFF /ON
to stop the pump down operation.
F567459_YS0111-2.indb 5F567459_YS0111-2.indb 5 23-Mar-11 11:23:22 AM23-Mar-11 11:23:22 AM

6
Recommendation
Recommendation
• It is strongly recommended to have the authorized dealer to change the water temperature range. The temperature range
for water outlet temperature and outdoor ambient temperature could be set by control panel.
Perform the steps below to set preferred temperature range.
SET
SELECT
CANCEL
ERROR
RESET
SETTING STATUS
SEARCH
PUMPDW
CHECK
2,4
1,5
3
STEP 1: Press
SET
for 5 seconds to enter SETTING mode. “SETTING” indicator is ON.
STEP 2: Press or to choose a parameter.
H2O Lo: Water outlet set
temperature at low outdoor
ambient set temperature
Selection range:
25°C ~ 55°C
HEAT
SETTING
STATUS
PUMPDW
C
H2O Hi: Water outlet set
temperature at high outdoor
ambient set temperature
HEAT
SETTING
STATUS
PUMPDW
C
Selection range:
25°C ~ 55°C
Out Lo: Low outdoor
ambient set temperature
HEAT
SETTING
STATUS
PUMPDW
C
Selection range:
-15°C ~ 15°C
Out Hi: High outdoor
ambient set temperature
HEAT
SETTING
STATUS
PUMPDW
C
Selection range:
-15°C ~ 15°C
Note: Please make sure High outdoor ambient set temperature (Out Hi) is always higher than Low outdoor
ambient set temperature (Out Lo).
STEP 3: After selecting the desired parameter,press
SELECT
to enter the parameter. “ ” indicator will blink when a
parameter is selected.
STEP 4: Press or to set the desired temperature.
STEP 5: Press
SET
again to confirm the setting.
• Repeat steps 2 to 5 to set other parameters.
• Press
C
AN
C
E
L
or wait 30 seconds to exit SETTING mode.
• The setting temperature will be stored in the system once confirm.
• “SETTING” mode cannot be activated when the “PUMPDW” and “STATUS” indicator is ON.
ADVANCE OPERATIONADVANCE OPERATION
F567459_YS0111-2.indb 6F567459_YS0111-2.indb 6 23-Mar-11 11:23:23 AM23-Mar-11 11:23:23 AM

7
ENGLISH
CARE & CLEANINGCARE & CLEANING
CAUTION
• Switch off the power supply before cleaning.
Indoor Unit & Control Panel
Indoor Unit & Control Panel
• Do not splash water directly.
• Wipe the unit gently with a soft, dry cloth.
External Filter
External Filter
• Please clean the external filter at least once a year. Fail to do so might cause filter clogged, consequent system
breakdown. Please consult authorized dealer.
Outdoor Unit
Outdoor Unit
• Do not obstruct the air inlet and air outlet vents, it may cause low performance or breakdown. Please remove obstacles to
assure the ventilation.
• During winter, please clean and remove the snow near outdoor unit so that the snow does no cover the air inlet and air
outlet vents.
Inspection
Inspection
• In order to ensure optimal performance of the unit, seasonal inspections on the unit, external filter and field wiring have to
be carried out at regular intervals. This maintenance should be carried out by authorized dealer.
• Clear any obstruction at the air inlet and air outlet vents of outdoor unit.
For Extended Non-Use
For Extended Non-Use
• Turn off the power supply.
Perform the steps below to check system status
Perform the steps below to check system status
SET
SELECT
CANCEL
ERROR
RESET
SETTING STATUS
SEARCH
PUMPDW
CHECK
2
1
STEP 1: Press
CHECK
for 5 seconds to enter STATUS mode.
STEP 2: Press or to check the Water Inlet Temperature, Tank Temperature, Compressor Running
Frequency or Error History.
• Press
C
AN
C
E
L
or wait 30 seconds to exit STATUS mode.
• Once STATUS mode is entered, “STATUS” indicator is ON.
• STATUS mode cannot be activated when the “SETTING” indicator is ON.
F567459_YS0111-2.indb 7F567459_YS0111-2.indb 7 23-Mar-11 11:23:24 AM23-Mar-11 11:23:24 AM

8
TROUBLESHOOTINGTROUBLESHOOTING
Symptom
Symptom
Cause
Cause
Water flowing sound during operation. • Refrigerant flow inside the unit.
Operation is delayed a few minutes after
restart. • The delay is a protection to the unit’s compressor.
Outdoor unit emits water/steam. • Condensation or evaporation occurs on pipes.
Outdoor unit emits steam during heating
mode. • This is due to defrost operation happens at the heat exchanger.
Outdoor unit does not operate. • When the outdoor temperature is out of the operation condition range,
the heatpump system enter protection control.
Air-to-Water Heatpump system operation will
turn off. • If indoor unit water inlet temperature is lower than 20°C. Please set the heater of tank more than 20°C.
System difficult to heat-up. • When heating is operated by indoor unit together with floor heating or
panel heater simultaneously, there may be case where warm water
temperature is getting lower and cause floor heating or panel heater
heat-up is weaken.
• When outdoor air temperature is low, it may be difficult to get warm.
• Is the snow pile blocking the discharge outlet or intake inlet of outdoor
unit.
• When water outlet set temperature is low, it may be difficult to get warm.
System cannot get warm instantly. • Due to the nature of the heatpump system, it may take some time to
heat-up the water if the unit is operated from cold-start.
Operation starts after power resumes. • Auto restart is in function and operates under.
The following symptoms do not indicate malfunction.
The following symptoms do not indicate malfunction.
Symptom
Symptom
Check
Check
Heating operation is not working efficiently. • Set the temperature correctly.
• Is the panel heater valve closed.
• Clear any obstruction at the air inlet and air outlet vents of outdoor unit.
Noisy during operation. • Check if the unit has been installed at an incline or the cover is not
closed properly.
The unit does not work. • Check if the circuit breaker is tripped.
Operation LED is no lit or control panel display
is blank. • Is the power supply off or power failure.
Check the following before calling for servicing.
Check the following before calling for servicing.
The operation LED blinks and error code appear on control panel display.
The operation LED blinks and error code appear on control panel display.
WATER INLET ERROR
• Turn the unit off and reveal the error code to authorized dealer.
F567459_YS0111-2.indb 8F567459_YS0111-2.indb 8 23-Mar-11 11:23:25 AM23-Mar-11 11:23:25 AM

9
ENGLISH
NON SERVICEABLE CRITERIAS
NON SERVICEABLE CRITERIAS
TURN OFF POWER SUPPLY then please consult authorized dealer under the following conditions:
• Abnormal noise during operation.
• Water/foreign particles have entered the control panel.
• Water leaks from Indoor unit.
• Circuit breaker switches off frequently.
• Power cord becomes unnaturally warm.
• Switches or buttons are not functioning properly.
Information for Users on Collection and Disposal of Old Equipment
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points,
in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from inappropriate waste
handling.
For more information about collection and recycling of old products, please contact your local municipality,
your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
INFORMATIONINFORMATION
The operation LED blinks and error code appear on control panel display.
F567459_YS0111-2.indb 9F567459_YS0111-2.indb 9 23-Mar-11 11:23:25 AM23-Mar-11 11:23:25 AM

10
Tack för ditt inköp av
Panasonic -produkt
INNEHÅLLSFÖRTECKNING
INNEHÅLLSFÖRTECKNING
SÄKERHETSFÖRESKRIFTER
10~11
PRODUKTÖVERSIKT
12
GRUNDLÄGGANDE ANVÄNDNING
13
AVANCERAD ANVÄNDNING
14
UNDERHÅLL & RENGÖRING
15
PROBLEMLÖSNING
16
INFORMATION
17
OBS :
Bilderna i denna skötselanvisning
är endast illustrativa och kan därför
skilja sig från den faktiska modellen.
Förändringar kan göras utan
föregående meddelande angående
framtida förbättringar.
• Panasonics Luft-till-Vatten-Värmepump är ett split-system som består
av endast en inomhusenhet och en utomhusenhet. Det här systemet
är tillverkat för att användas med Panasonics ackumulatortank.
Om du använder Panasonics Luft-till-Vatten-Värmepump med en
ackumulatortank från en annan tillverkare än Panasonic, kan Panasonic
varken garantera god prestanda eller tillförlitlig drift.
• I denna manual beskrivs hur du använder värmepumpsystemet mellan
inomhus- och utomhusenheterna enbart.
• För annan användning av t.ex. vattentank, värmeelement och
golvvärmesystem, se bruksanvisningen från respektive tillverkare.
För att undvika skada på dig själv, skada på andra, eller skada på
egendom, var god iaktta följande.
Felaktig användning orsakad av att skötselanvisningen inte följts kan leda
till skador, nedan klassas deras allvar:
VARNING
VARNING
Denna symbol varnar för dödsfara eller
allvarliga skador.
FÖRSIKTIGHET
FÖRSIKTIGHET
Denna symbol varnar för personskada eller
skada på egendom.
Instruktioner klassificeras med följande symboler:
Denna symbol betecknar en handling
som är FÖRBJUDEN.
Denna symbol betecknar ett
handhavande som MÅSTE UTFÖRAS.
VARNING
VARNING
INOMHUS- OCH UTOMHUSENHET
INOMHUS- OCH UTOMHUSENHET
Denna apparat är inte avsedd att användas av personer
(inklusive barn) med reducerad fysiska, sensoriska eller
mentala färdigheter, eller brist på erfarenhet och kunskap,
ifall de inte övervakats eller instruerats om användandet av
apparaten av en person som ansvarar för deras säkerhet.
Barn bör övervakas för att se till att de inte leker med
apparaten.
Var god rådfråga auktoriserad återförsäljare eller specialist för att
reparera, installera, avlägsna och återinstallera enheten. Felaktig
installation och hantering orsakar läckage, elstöt eller eldsvåda.
Installera inte enheten i en potentiellt explosiv eller
lättantändlig miljö. Underlåtenhet i detta kan resultera i skada
till följd av eldsvåda.
För inte in dina fingrar eller andra föremål i
inomhus- eller utomhusenheten, eftersom
roterande delar kan orsaka personskada.
Rör inte utomhusenheten under blixtoväder, då det kan
orsaka elstöt.
Försök inte reparera enheten på egen hand. Detta kan i så
fall orsaka personskada, om det görs på fel sätt.
Installera inte inomhusenheten utomhus. Den är endast
utformad för installation inomhus.
TILLÅTNA
TILLÅTNA
DRIFTSFÖRHÅLLANDEN
DRIFTSFÖRHÅLLANDEN
Vattenutloppstemperatur
(°C) Inomhus
VÄRME Max. 55
Min. 25
Omgivningstemperatur
(°C) Utomhus
VÄRME Max. 35
Min. -20
MÄRK : Då utomhustemperaturen är
utanför temperaturområdet
ovan, sjunker
uppvärmningskapaciteten
avsevärt och utomhusenheten
kan stoppa för skyddskontroll.
SÄKERHETSFÖRESKRIFTERSÄKERHETSFÖRESKRIFTER
F567459_YS0111-2.indb 10F567459_YS0111-2.indb 10 23-Mar-11 11:23:25 AM23-Mar-11 11:23:25 AM