Panasonic SA-PT250GCP User manual

lGENERAL
Power Supply:
A
C 110 to 127 V, 220 to 240
V, 50/60 Hz
Power Consumption: 135 W
Power Consumption in Standby Mode:
approx. 0.8 W
Dimensions (W×H×D): 430×60×363 mm
Mass: Main unit approx. 3.5 kg
Operating Temperature Range: +5°C to +35°C
Operating Humidity Range: 5% to 90% RH (no
condensation)
lAMPLIFIER SECTION
RMS Output Power: Dolby Digital Mode
lTotal RMS Dolby Digital mode power:
750 W
At 1 kHz and total harmonic of 10%
lFront Ch: 125 W / Channel (3 Ω)
lCenter Ch: 125 W / Channel (3 Ω)
lSurround Ch: 125 W / Channel (3 Ω)
©2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
SA-PT250GCP
Colour
(S).......................Silver Type
At 100 Hz and total harmonic of 10%
lSubwoofer Ch: 125 W / Channel (3 Ω)
PMPO Output Power: 5600 W
DIN Output Power: Dolby Digital Mode
lTotal DIN Dolby Digital mode power:
450 W
At 1 kHz and total harmonic of 1%
lFront Ch: 75 W / Channel (3 Ω)
lCenter Ch: 75 W / Channel (3 Ω)
lSurround Ch: 75 W / Channel (3 Ω)
At 100 Hz and total harmonic of 1%
lSubwoofer Ch: 75 W / Channel (3 Ω)
lFM TUNER, TERMINALS SECTION
Preset Memory: FM 30 stations
Frequency Modulation (FM)
Frequency range: 87.50-108.00 MHz
(50-kHz step)
Sensitivity: 1.8 µV (IHF)
S/N 26 dB: 1.4 µV
DVD Home Theater Sound System
Specifications
ORDER NO. MD0705013CE

Antenna terminals: 75 Ω(unbalanced)
Phone Jack:
Terminal: Stereo, 3.5 mm jack
Mic Jack:
Sensitivity: 0.7 mV, 1.2 kΩ
Terminal: Mono, 6.3 mm jack (2 system)
Front Music Port:
Sensitivity: 100 mV, 1.4 kΩ
Terminal: Stereo, 3.5 mm jack
USB Port:
USB standard: USB 2.0 full speed
Media file format support: MP3 (*.mp3)
WMA (*.wma)
JPEG (*.Jpg, *.JPEG)
MPEG4 (*.asf)
USB device file system: (FAT12) (FAT16) (FAT32)
USB Port power: Max. 500 mA
lDISC SECTION
Discs played (8 cm or 12 cm):
(1) DVD [DVD-Video, DivX (*6, *7)]
(2) DVD-RAM [DVD-VR, MP3 (*2, *7), JPEG (*4, *7), MPEG4
(*5, *7), DivX (*6, *7)]
(3) DVD-R [DVD-Video, DVD-VR, MP3 (*2, *7), JPEG (*4, *7),
MPEG4 (*5, *7), DivX (*6, *7)]
(4) DVD-R DL [DVD-Video, DVD-VR]
(5) DVD-RW [DVD-Video, DVD-VR, MP3 (*2, *7), JPEG (*4, *7),
MPEG4 (*5, *7), DivX (*6, *7)]
(6) +R/+RW [Video]
(7) +R DL [Video]
(8) CD, CD-R/RW [CD-DA, Video CD, SVCD (*1), MP3 (*2, *7),
WMA (*3, *7), JPEG (*4, *7), MPEG4 (*5, *7), DivX (*6, *7)]
*1 Conforming to IEC62107
*2 MPEG-1 Layer 3, MPEG-2 Layer 3
*3 Windows Media Audio Ver.9.0 L3
lNot compatible with Multiple Bit Rate (MBR)
*4 Exif Ver 2.1 JPEG Baseline files
lPicture resolution: between 160 x 120 and 6144 x 4096
pixels (Sub sampling is 4:0:0, 4:2:0, 4:2:2, or 4:4:4).
Extremely long and narrow pictures may not be displayed.
*5 MPEG4 data recorded with the Panasonic SD multi cameras
or DVD video recorders.
lConforming to SD VIDEO specifications (ASF standard)/
MPEG4 (Simple Profile) video system/G.726 audio system.
*6 Plays all versions of DivX® video (including DivX®6) with
standard playback of DivX® media files. Certified to the DivX
Home Theater Profile.
*7 The total combined maximum number of recognizable audio,
picture and video contents and groups: 4000 audio, picture
and video contents and 400 groups.
Pick Up:
Wavelength:
lCD: 785 nm
lDVD: 662 nm
Laser power:
lCD: CLASS 1M
lDVD: CLASS 1
Audio Output (Disc):
Number of channels: 5.1 ch (FL, FR, C, SL, SR,
SW)
lVIDEO SECTION
V
ideo System: NTSC
Composite Video Output:
lOutput level: 1 Vp-p (75 Ω)
lTerminal: Pin jack (1 system)
Component Video Output: (480p/480i)
lY output level: 1 Vp-p (75 Ω)
lPBoutput level: 0.7 Vp-p (75 Ω)
lPRoutput level: 0.7 Vp-p (75 Ω)
lTerminal: Pin jack (Y: green, PB: blue,
PR: red) (1 system)
Note:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
Solder:
This model uses lead free solder (PbF).
Mechanism:
This model uses DL2S (Single tray) mechanism.
Refer to their respective original service manuals for *1, *2,
*3, *4.
2
SA-PT250GCP

1 Safety Precautions 6
1.1. GENERAL GUIDELINES 6
1.2. Before Repair and Adjustment 6
1.3. Protection Circuitry 6
1.4. Safety Parts Information 7
CONTENTS
Page Page
3
SA-PT250GCP

2 Prevention of Electrostatic Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 8
3 Precaution of Laser Diode 9
4 About Lead Free Solder (PbF) 10
4.1. Service caution based on legal restrictions 10
5 Handling Precautions for Traverse Unit 11
5.1. Cautions to Be Taken in Handling the Optical Pickup Unit
11
5.2. Grounding for electrostatic breakdown prevention 11
6 Accessories 13
7 Operation Procedures 14
7.1. Remote Control Key Buttons Operations 14
7.2. Main Unit Key Buttons Operations 15
7.3. Music Port Connection and Operation 16
7.4. USB Connection and Operation 17
7.5. Audio & Video Connections 18
7.6. Disc Information 19
8 Self-Diagnosis and Special Mode Setting 21
8.1. Service Mode Summary Table 21
8.2. Service Mode Table 21
8.3. DVD Self Diagnostic Function-Error Code 29
8.4. Sales Demonstration Lock Function 32
8.5. Service Precautions 33
9 Assembling and Disassembling 34
9.1. Disassembly Flow Chart 35
9.2. Main Components and P.C.B. Locations 36
9.3. Disassembly of Top Cabinet 37
9.4. Disassembly of the DVD Lid (When taking out disc
manually) 37
9.5. Disassembly of Front Panel 38
9.6. Disassembly of Volume P.C.B. 38
9.7. Disassembly of Mic P.C.B. 39
9.8. Disassembly of Panel P.C.B. 39
9.9. Disassembly of USB P.C.B. 40
9.10. Disassembly of Rear Panel 40
9.11. Disassembly of DVD Mechanism Unit 40
9.12. Disassembly of DVD Module P.C.B. 41
9.13. Disassembly of Main P.C.B. 41
9.14. Replacement of Regulator IC (IC2903) 42
9.15. Disassembly of D-Amp P.C.B. 42
9.16. Replacement of Digital Amp IC (IC5000) 43
9.17. Disassembly of SMPS, AC-Inlet & Voltage Selector P.C.B.
44
9.18. Replacement of Switch Regulator IC/Diode
(IC5701/D5702) 45
9.19. Replacement of Regulator Diode (D5801/D5802) 45
9.20. Replacement of Regulator Diode (D5803) 46
10 Assembly and Disassembly of DVD Mechanism Unit 47
10.1. Disassembly Procedure 47
11 Service Position 52
11.1. Checking & Repairing Panel P.C.B. 52
11.2. Checking & Repairing Mic P.C.B. 52
11.3. Checking & Repairing Main P.C.B. 52
11.4. Checking & Repairing D-Amp P.C.B. 53
11.5. Checking & Repairing DVD Module P.C.B. 53
11.6. Checking & Repairing SMPS P.C.B. 53
12 Measurements and Adjustments 54
12.1. Service Tools and Equipment 54
12.2. Important points in adjustment 54
12.3. Storing and handling of test discs 54
12.4. Optical adjustment 55
13 Abbreviations 56
14 Voltage and Waveform Chart 58
14.1. DVD Module P.C.B. 58
14.2. Main P.C.B. 59
14.3. D-Amp P.C.B. 60
14.4. SMPS P.C.B. 60
14.5. Panel & Tray Loading P.C.B. 61
14.6. Mic P.C.B. 61
14.7. Waveform Chart 62
15 Illustration of IC's, Transistors and Diodes 64
16 Wiring Connection Diagram 65
17 Block Diagram 67
17.1. System Control 67
17.2. DVD (Servo) 68
17.3. DVD (Audio) 69
17.4. DVD (Video) 70
17.5. Audio 71
17.6. Audio Digital Amp 72
17.7. Power 73
18 Schematic Diagram Notes 75
19 Schematic Diagram 77
19.1. DVD Module Circuit 77
19.2. Main, Panel & Mic Circuit 81
19.3. D-Amp & SMPS Circuit 87
19.4. Volume, USB, AC-Inlet, Tray Loading & Voltage Selector
Circuit 91
19.5. Optical Pickup Unit Circuit 92
20 Printed Circuit Board 93
20.1. DVD Module P.C.B. 93
20.2. Main P.C.B. 94
20.3. Panel & Mic P.C.B. 95
20.4. D-Amp P.C.B. 96
20.5. SMPS P.C.B. 97
20.6. Volume, USB, AC-Inlet, Tray Loading & Voltage Selector
P.C.B. 98
21 Basic Troubleshooting Guide 99
21.1. Basic Troubleshooting Guide for Traverse Unit (DVD
Module P.C.B) 99
22 Overall Block Diagram for PT250 100
22.1. SC-PT250 Simplified Block 100
22.2. SC-PT250 Power Block 101
22.3. SC-PT250 SMPS Block 102
23 Terminal Function of ICs 103
23.1. IC2001 (C2CBYY000440): System Control IC 103
24 Exploded Views 104
24.1. Cabinet Parts Location 105
24.2. Packaging 107
4
SA-PT250GCP

25 Replacement Parts List 108 25.1. Component Parts List 109
5
SA-PT250GCP

1 Safety Precautions
1.1. GENERAL GUIDELINES
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, carry out the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. LEAKAGE CURRENT COLD CHECK
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be
1.1.2. LEAKAGE CURRENT HOT CHECK
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to
the customer.
Figure 1
1.2. Before Repair and Adjustment
Disconnect AC power to discharge unit AC Capacitors as such C5700, C5701, C5703, C5704, C5705 through a 10 Ω,10W
resistor to ground.
Caution:
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 110 to 127 V/ 220 to 240 V, 50/60 Hz in NO SIGNAL mode volume minimal should be ~ 600 mA.
1.3. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
· No sound is heard when the power is turned on.
· Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
6
SA-PT250GCP

“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.4. Safety Parts Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts
should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design
without permission of manufacturer.
Table 1
Reference No. Part No. Part Name & Description Remarks
340 RAE2023Z-S TRAVERSE UNIT [M]
PC5701 B3PBA0000402 PHOTO COUPLER [M]
PC5702 B3PBA0000402 PHOTO COUPLER [M]
PC5720 B3PBA0000402 PHOTO COUPLER [M]
PC5799 B3PBA0000402 PHOTO COUPLER [M]
D5701 B0FBAR000041 DIODE [M]
DZ5701 ERZV10V511CS ZENER [M]
TH5701 D4CAC8R00002 THERMISTOR [M]
TH5860 D4CC11040013 THERMISTOR [M]
L2101 J0JBC0000015 CHIP INDUCTOR [M]
L2201 J0JBC0000015 CHIP INDUCTOR [M]
L2802 J0JBC0000015 CHIP INDUCTOR [M]
L2803 J0JBC0000015 CHIP INDUCTOR [M]
L2804 J0JBC0000015 CHIP INDUCTOR [M]
L2805 J0JBC0000015 CHIP INDUCTOR [M]
L5001 G0B9R5K00003 LINE CHOKE COIL [M]
L5002 G0B9R5K00004 LINE CHOKE COIL [M]
L5201 G0B9R5K00004 LINE CHOKE COIL [M]
L5301 G0B9R5K00003 LINE CHOKE COIL [M]
L5401 G0B9R5K00003 LINE CHOKE COIL [M]
L5402 G0B9R5K00004 LINE CHOKE COIL [M]
L5701 ELF15N035AN LINE FILTER [M]
L5702 ELF22V035B COIL [M]
L6101 J0JBC0000019 CHIP INDUCTOR [M]
L6201 J0JBC0000019 CHIP INDUCTOR [M]
L6801 J0JBC0000019 CHIP INDUCTOR [M]
L6904 J0JBC0000019 CHIP INDUCTOR [M]
L6905 J0JBC0000019 CHIP INDUCTOR [M]
L6906 J0JBC0000019 CHIP INDUCTOR [M]
L6907 J0JBC0000019 CHIP INDUCTOR [M]
L6908 J0JBC0000019 CHIP INDUCTOR [M]
L6909 J0JBC0000019 CHIP INDUCTOR [M]
T2900 G4D1A0000117 SWITCHING TRANSFORMER [M]
T5701 ETS42BN1A6AD MAIN TRANSFORMER [M]
T5751 ETS19AB236AG BACK-UP TRANSFORMER [M]
F1 K5D802BNA005 FUSE [M]
FP2900 K5G401A00008 FUSE PROTECTOR [M]
P5701 K2AA2B000015 JACK AC INLET [M]
A2 K2CQ2CA00002 AC CORD [M]
C5700 F1BAF1020020 1000P [M]
C5701 ECQU2A334MLA 0.33 [M]
C5703 ECQU2A104MLC 0.1 [M]
C5704 F1BAF1020020 1000P [M]
C5705 F1BAF1020020 1000P [M]
7
SA-PT250GCP

2 Prevention of Electrostatic Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).
8
SA-PT250GCP

3 Precaution of Laser Diode
CAUTION :
This product utilizes a laser diode with the unit turned on, invisible laser radiation is emitted from the pickup lens.
Wavelength : 662nm/785nm
Maximum output radiation power from pickup : 100µW/VDE
Laser radiation from pickup unit is safety level, but be sure the followings:
1. Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pickup unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pickup lens for a long time.
9
SA-PT250GCP

4 About Lead Free Solder (PbF)
4.1. Service caution based on legal restrictions
4.1.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)
Service caution for repair work using Lead Free Solder (PbF)
· The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
· To put lead free solder, it should be well molten and mixed with the original lead free solder.
· Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
· Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt
the lead free solder.
· Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30
degrees C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
· The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
10
SA-PT250GCP

5 Handling Precautions for Traverse Unit
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the traverse unit.
5.1. Cautions to Be Taken in Handling the Optical Pickup Unit
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed should
be short-circuited with a short pin or a clip.
3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexible
cable, cut off the antistatic FPC.
5.2. Grounding for electrostatic breakdown prevention
Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static
electricity in the working environment. Proceed servicing works under the working environment where grounding works is
completed.
5.2.1. Worktable grounding
1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.
5.2.2. Human body grounding
1. Use the anti-static wrist strap to discharge the static electricity form your body.
11
SA-PT250GCP

12
SA-PT250GCP

Remote control
Antenna wire
AC cord
AC plug adaptor
Screw
Speaker cord
Speaker label
Video cable
6 Accessories
· Note: Refer to “Replacement Parts List” (Section 25) for the part number.
13
SA-PT250GCP

7 Operation Procedures
7.1. Remote Control Key Buttons Operations
Adjust the television volume
Select the source
DVD:
DVD/CD
FM
EXT-IN: USB, AUX, MUSIC P.
Show the current disc’s playback condition
Adjust the volume of the main unit
Basic operations for play
Show a disc menu or play list
Select or confirm menu items on the
television screen , Frame-by-frame
Return to previous screen,
Show the Setup menu
Telev ision o perations
Switch the main unit on or off
Change the television’s video input mode
Select disc’s title numbers and etc.,
Enter numbers
Select preset radio stations
Show a disc top menu
or program list
Show on-screen menu,
Karaoke
Show the display on the main unit,
Set the sleep timer
This function enables you to turn off the unit
automatically after the set time.
SLEEP 30 SLEEP 60 SLEEP 90
OFF SLEEP 120
To cancel the timer
Press and hold [ SLEEP] to select "OFF".
To confirm the remaining time
Press and hold [ SLEEP] again. To mute the sound
To cancel
Press [MUTING] again or adjust the
volume.
Muting is cancelled when you switch the
unit to standby.
14
SA-PT250GCP

7.2. Main Unit Key Buttons Operations
AC supply indicator [AC IN]
This indicator lights when the unit
is connected to the AC mains
supply.
OPEN/CLOSE
Open or close the
disc tray
Display
/ TUNE MODE / FM MODE
Stop playback, Select the tuning mode,
Adjust the FM reception condition
/ , / / TUNE
Skipping or slow-search play,
Select the radio stations
MUSIC PORT jack
Connect an external device
+, VOLUME
Turn the volume
up or down
SELECTOR
DVD/CD USB FM MUSIC. P. AUX
USB port
Connect a USB device
Standby/on switch [ /I]
Press to switch the unit from on to
standby mode or vice versa. In standby
mode, the unit is still consuming a small
amount of power.
/MEMORY
Disc playback ,
Memorise the receiving
radio stations
Headphones
(not included)
Headphone plug type:
3.5 mm stereo mini plug
Reduce the volume before
connecting.
Audio is automatically
switched to 2-channel stereo.
To prevent hearing damage,
avoid listening for prolonged
periods of time.
Remote control signal sensor
MIC jack
Connect a microphone
MIC VOL
Adjust the microphone volume
POWER
15
SA-PT250GCP

7.3. Music Port Connection and Operation
The Music Port allows you to connect and enjoy music from
an external device (example: MP3 player) through your
home theater system.
Preparation
To avoid distorted sound, make sure that any equalizer
function of your external device is turned off.
1Reduce the volume and connect the external device
(not included).
Plug type 3.5 mm stereo mini plug
External device
(not included)
Reduce the volume
before connecting.
2To select "MUSIC P.".
USB AUX MUSIC P.
3Adjust the external device volume to a normal
listening level, and then adjust the volume of the
main unit.
You can enjoy surround sound when you turn on
Super Surround (MOVIE, MUSIC) ( OI page 29).
16
SA-PT250GCP

7.4. USB Connection and Operation
The USB connectivity enables you to connect and play
tracks or files from USB mass storage class devices.
Typically, USB memory devices. (Bulk only transfer)
Preparation
Before connecting any USB mass storage device to the
unit, ensure that the data stored therein has been backed
up.
It is not recommended to use a USB extension cable. The
USB device is not recognised by this unit.
1 Connect the USB mass storage device (not included).
USB enabled device
(not included)
It is not recommended to use a USB
extension cable. The device connected
via the cable will not be recognised by
this unit.
2 To select "USB" as the source, press several times.
USB AUX MUSIC P.
Select the desired item for playback.
OR
Example:
LAYBACK MENUP
AUD I O
/ PCTURE
VIDEO
I
SBU
Fish eLong
MP 3 I 3DTAG
jpeg
MPEG4
WMA
OROT
3 Adjust the volume of the main unit.
4 Begin playback by selecting the track from the USB
mass storage device.
Example:
SBU
OR OT/FI
TRACK 0 1
HSLENGO
TRACK 0 2
TRACK 0 3
TRACK 0 4
TRACK 0 5
TRACK 0 6
TRACK 0 7
TRACK 0 8
TRACK 0 9
TRACK 1 0
TRACK 1 1
TRACK 1 2
TRACK 1 3
TRACK 1 4
TRACK 1 5
TRACK 1 6
TRACK 1 7
TRACK 1 8
OR OR
To return to the previous screen
Press [-RETURN].
For other operating functions, they are similar as those
described on "DISC OPERATIONS" ( OI page 16 to 27).
Compatible Devices
Devices which are defined as USB mass storage
class:
USB devices that support bulk only transfer.
USB devices that support USB 2.0 full speed.
Supported Formats
File name File extension
Still pictures JPG
1
.jpg .jpeg
Music MP3
WMA
.mp3
.wma
Video MPEG4
2
.asf
1
It may not be possible to play all the files due to the condition on
how they were created.
2
For Panasonic D-Snap/DIGA.
Note
CBI (Control/Bulk/Interrupt) is not supported.
Digital Cameras that use PTP protocol or which require
additional program installation when connected to a PC are not
supported.
A device using NTFS file system is not supported.
[Only FAT 12/16/32 (File Allocation Table 12/16/32) file system is
supported].
Depending on the sector size, some files may not work.
It will not operate with Janus enabled MTP (Media Transfer
Protocol) devices.
Maximum folder: 256 folders
Maximum file: 4000 files
Maximum file name: 12 characters
Maximum folder name: 12 characters
Only one memory card will be selected when connecting a multi-
port USB card reader. Typically the first memory card inserted.
WMA
17
SA-PT250GCP

7.5. Audio & Video Connections
7.5.1. Optional Connection for Set Top Box, Cable TV, or Video Cassette Recorder
Audio cable
(not included)
Rear panel of
this main unit
Video cable
(included)
Television
(not included)
Cable TV
box or video
cassette
recorder
(not included)
RF cable
(not included)
To your cable TV service or television antenna
7.5.2. Optional Audio Connection for Video Cassette Recorder or Television
Press [EXT-IN] ( OI page 15) to select "AUX" as the source to operate the audio output.
Audio cable
(not included)
Rear panel of
this main unit
Video cable
(included)
Television
(not included)
This audio connection will enable you to play audio from
your television through your home theater system.
18
SA-PT250GCP

7.6. Disc Information
7.6.1. Disc Playability (Media)
Commercial discs
Disc Logo
Indicated in
these
instructions by
Remarks
DVD-Video High quality movie and music discs.
Video CD
Music discs with video.
Including SVCD (Conforming to IEC62107).
CD Music discs.
Recorded discs ( o : Pl ayable, x : Not playable)
Disc Logo
Recorded on a DVD
video recorder, etc. Recorded on a personal computer, etc.
Finalizing
6
2 4 9
DVD-RAM
o
x
ooo
8
o
Not
necessary
DVD-R/RW
oo
x
oooo
Necessary
DVD-R DL
o
3
o
xxxxx Necessary
+R/+RW x(
o )
5
xxxxx Necessary
+R DL x(
o )
5
xxxxx Necessary
CD-R/RW
1
ooooo
Necessary
7
It may not be possible to play all the above-mentioned discs in some cases due to the type of disc, the condition of the
recording, the recording method, or how the files were created [ Section 7.6.2. File Extension Type Support (WMA/MP3/
JPEG/MPEG4/DivX)]
1
This unit can play CD-R/RW recorded with CD-DA or Video CD format.
2
Discs recorded on DVD video recorders or DVD video cameras, etc. using Version 1.1 of the Video Recording Format (a unified video
recording standard).
3
Discs recorded on DVD video recorders or DVD video cameras using Version 1.2 of the Video Recording Format (a unified video
recording standard).
4
Discs recorded on DVD video recorders or DVD video cameras using DVD-Video Format.
5
Recorded using a format different from DVD-Video Format, therefore, some functions cannot be used.
6
A process that allows play on compatible equipment. To play a disc that is disp layed as "Necessary" on this unit, the disc must first be
finalized on the device it was recorded on.
7
Closing the session will also work.
8
MPEG4 data recorded with the Panasonic SD multi cameras or DVD video recorders [conforming to SD VIDEO specifications (ASF
standard)/MPEG4 (Simple Profile) video system/G.726 audio system].
9
Functions added with DivX ultra are not supported.
Note about using a DualDisc
The digital audio content side of a DualDisc does not meet the
technical specifications of the Compact Disc Digital Audio
(CD-DA) format so playback may not be possible.
Discs that cannot be played
DVD-RW version 1.0, DVD-Audio, DVD-ROM, CD-ROM,
CDV, CD-G, SACD, Photo CD, DVD-RAM that cannot be
removed from their cartridge, 2.6-GB and 5.2-GB DVD-
RAM, and "Chaoji VCD" available on the market including
CVD, DVCD and SVCD that do not conform to IEC62107.
19
SA-PT250GCP

7.6.2. File Extension Type Support (WMA/MP3/JPEG/MPEG4/DivX)
When there are more than eight groups, the eighth group onwards will be displayed on one vertical line in the menu
screen.
There may be differences in the display order on the menu screen and computer screen.
This unit cannot play files recorded using packet write.
DVD-RAM
Discs must conform to UDF 2.0.
DVD-R/RW
Discs must conform to UDF bridge (UDF 1.02/ISO9660).
This unit does not support multi-session. Only the default session is played.
CD-R/RW
Discs must conform to ISO9660 level 1 or 2 (except for extended formats).
This unit supports multi-session but if there are many sessions it takes more time for play to start. Keep the number of
sessions to a minimum to avoid this.
Naming folders and files
Files are treated as contents and folders are treated as groups on this unit.
At the time of recording, prefix folder and file names. This should be with numbers that have an equal number of digits,
and should be done in the order you want to play them (this may not work at times). Files must have the extension
(see below).
(Extension: ".WMA" or ".wma")
Compatible compression rate: between 48 kbps and 320 kbps.
You cannot play WMA files that are copy-protected.
This unit does not support Multiple Bit Rate (MBR).
(Extension: ".MP3" or ".mp3")
Compatible compression rate: between 32 kbps and 320 kbps.
This unit does not support ID3 tags.
Compatible sampling rates:
DVD-RAM, DVD-R/RW: 11.02, 12, 22.05, 24, 44.1 and 48 kHz
CD-R/RW: 8, 11.02, 12, 16, 22.05, 24, 32, 44.1 and 48 kHz
(Extension: ".JPG", ".jpg", ".JPEG" or ".jpeg")
JPEG files taken on a digital camera that conform to DCF Standard (Design rule for Camera File system) Version 1.0 are
displayed. Files that have been altered, edited or saved with computer picture edi ting software may not be displayed.
This unit cannot display moving pictures, MOTION JPEG and other such formats, and still pictures other than JPEG
(Example: TIFF), or play pictures with attached audio.
(Extension: ".ASF" or ".asf")
You can play MPEG4 data [conforming to SD VIDEO specifications (ASF standard)/MPEG4 (Simple Profile) video
system/G.726 audio system] recorded with Panasonic SD multi cameras or DVD video rec orders with this unit.
The recording date may differ from that of the actual date.
(Extension: ".DIVX", ".divx", ".AVI" or ".avi")
You can play all versions of DivX video (including DivX 6) [DivX video system/MP3, Dolby Digital or MPEG audio
system] with standard playback of DivX media files. Functions added with DivX Ultra are not supported.
DivX files greater than 2 GB or have no index may not be played properly on this unit.
This unit supports all resolutions up to maximum of 720 x 480 (NTSC)/720 x 576 (PAL).
You can select up to eight types of audio and subtitles on this unit.
20
SA-PT250GCP