Panasonic TH-LR37G10 User manual

© Panasonic Corporation 2009. Unauthorized
copying and distribution is a violation of law
ORDER NO. MTV0901681CE
LCD TV
Model No. TH-LR37G10
Chassis: LH89
Destination: CIS
Specifications
Power Source AC 220 - 240 V, 50/60 Hz
Power Consumption
Power Rating 154 W
Standby condition 0.4 W
Display panel
Aspect Ratio 16:9
Visible screen size 94 cm (diagonal)
819 mm (W) ×460 mm (H)
(No. of pixels) 2,073,600 (1,920 (W) ×1,080 (H))
Sound
Speaker 160 mm ×42 mm ×2 pcs, 8 Ω
Audio Output 20 W (10 W + 10 W), 10% THD
Headphones M3 (3.5 mm) stereo mini Jack ×1
PC Signals VGA, SVGA, XGA
SXGA ...... (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems / Band name SYSTEMS FUNCTIONS
1PAL B, G, H
Reception of broadcast transmission and
playback from video cassette tape recorders.
2PAL I
3PAL D, K
4SECAM B, G
5SECAM D, K
6SECAM K1
7NTSC M (NTSC 3.58 / 4.5MHZ)

TH-LR37G10
2
8NTSC 4.43 / 5.5 MHz
Playback from special VCR’s or DVD.
9NTSC 4.43 / 6.0 MHz
10 NTSC 4.43 / 6.5 MHz
11 NTSC 3.58 / 5.5 MHz
12 NTSC 3.58 / 6.0 MHz
13 NTSC 3.58 / 6.5 MHz
14 SECAM I
15 PAL 60 Hz / 5.5 MHz Playback from Special Disc Players and
Special VCR’s or DVD.
16 PAL 60 Hz / 6.0 MHz
17 PAL 60 Hz / 6.5 MHz
Receiving Channels (Regular TV)
VHF BAND 2 - 12 (PAL / SECAM B, K1)
0 - 12 (PAL B AUST.)
1 - 9 (PAL B N.Z.)
1 - 12 (PAL / SECAM D)
1 - 12 (NTSC M JAPAN)
2 - 13 (NTSC M U.S.A.)
UHF BAND 21 - 69 (PAL G, H, I / SECAM G, K, K1)
28 - 69 (PAL B AUST.)
13 - 57 (PAL D, K)
13 - 62 (NTSC M JAPAN)
14 - 69 (NTSC M U.S.A.)
CATV S1 - S20 (OSCAR)
1 - 125 (U.S.A. CATV)
C13 - C49 (JAPAN)
S21 - S41 (HYPER)
Z1 - Z37 (CHINA)
5A, 9A (AUST.)
Aerial - Rear VHF / UHF
Operating Conditions Temperature : 0°C - 35°C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 Input AUDIO L-R RCA PIN Type ×2 0.5 V [rms]
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
COMPONENT Y 1.0 V[p-p] (including synchronization)
PB/CB, PR/CR± 0.35 V [p-p]
AV2 Input AUDIO L-R RCA PIN Type ×2 0.5 V [rms]
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
COMPONENT Y 1.0 V[p-p] (including synchronization)
PB/CB, PR/CR± 0.35 V [p-p]
AV3 Input AUDIO L-R RCA PIN Type ×2 0.5 V [rms]
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
S-VIDEO Mini DIN 4-pin Y: 1.0 V[p-p] (75 Ω) C: 0.286 V[p-p] (75 Ω)
Monitor
Output AUDIO L-R RCA PIN Type ×2 0.5 V [rms] (High impedance)
VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
Others HDMI 1-4 Input TYPE A Connectors • This TV supports “HDAVI Control 4” function.
PC Input HIGH-DENSITY D-SUB 15 PIN R, G, B / 0.7 V[p-p] (75 Ω)
HD, VD / TTL LEVEL 2.0-5.0 V[rms] (high impedance)
DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber optic
Card Slot SD Card slot ×1
Dimension (W x H x D) 894 mm ×611 mm ×287 mm (With Pedestal)
894 mm ×568 mm ×99 mm (TV only)
Mass 17.5 kg Net (With Pedestal)
15.0 kg Net (TV only)
Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.

TH-LR37G10
3
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 5
1.1. General Guidelines---------------------------------------- 5
1.2. Touch-Current Check------------------------------------- 5
1.3. LH89 Chasis Block Diagram---------------------------- 6
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices------------------ 7
3 About Lead Free Solder (PbF) ------------------------------- 8
4 Power LED Blinking Timing----------------------------------- 9
5 Chassis Board----------------------------------------------------10
5.1. Chassis MTG Installation-------------------------------10
5.2. Chassis Screw Fixing------------------------------------11
6 Location of Controls and Components ------------------12
6.1. Wire Dressing ---------------------------------------------12
7 Disassembly and Assembly Instructions ---------------13
7.1. AC Cord Dressing - 1------------------------------------13
7.2. AC Cord Dressing - 2------------------------------------14
7.3. AC Cord Dressing - 3------------------------------------15
7.4. AC Cord Bracket Installation---------------------------16
7.5. VESA Metal And Bottom MTG Installation---------17
7.6. LED Panel Installation-----------------------------------18
7.7. Control Panel Assembly Installation-----------------19
7.8. Control Panel Support Installation--------------------20
7.9. Side AV Bracket Installation ---------------------------21
7.10. LCD Panel Installation-----------------------------------22
7.11. EMI Sticking - A-------------------------------------------23
7.12. EMI Sticking - B-------------------------------------------24
7.13. Sticking Sponge - A --------------------------------------25
7.14. Sticking Felt And Sponge - B --------------------------26
7.15. Sticking Felt And Sponge - C--------------------------27
7.16. Back Cover Screw----------------------------------------28
8 Service Mode Adjustment ------------------------------------29
8.1. Self Check Mode -----------------------------------------29
8.2. Hotel Mode Adjustment---------------------------------29
8.3. Hotel Mode-------------------------------------------------29
9 Measurements and Adjustments---------------------------30
9.1. Voltage Chart of A Board-------------------------------30
9.2. Voltage Chart of P Board-------------------------------30
10 Printed Circuit Board-------------------------------------------31
10.1. A-Board -----------------------------------------------------31
10.2. A-Board -----------------------------------------------------33
10.3. P-Board -----------------------------------------------------35
10.4. P-Board -----------------------------------------------------37
11 Schematic Diagram---------------------------------------------39
11.1. Schematic Diagram Notes -----------------------------39
11.2. A Board -----------------------------------------------------40
11.2.1. A Board - Sheet : 001 (1 / 9)----------------------40
11.2.2. A Board - Sheet : 001 (2 / 9)----------------------41
11.2.3. A Board - Sheet : 001 (3 / 9)----------------------42
11.2.4. A Board - Sheet : 001 (4 / 9)----------------------43
11.2.5. A Board - Sheet : 001 (5 / 9)----------------------44
11.2.6. A Board - Sheet : 001 (6 / 9)----------------------45
11.2.7. A Board - Sheet : 001 (7 / 9) ---------------------46
11.2.8. A Board - Sheet : 001 (8 / 9) ---------------------47
11.2.9. A Board - Sheet : 001 (9 / 9) ---------------------48
11.2.10. A Board - Sheet : 002 (1 / 4) ---------------------49
11.2.11. A Board - Sheet : 002 (2 / 4) ---------------------50
11.2.12. A Board - Sheet : 002 (3 / 4) ---------------------51
11.2.13. A Board - Sheet : 002 (4 / 4) ---------------------52
11.2.14. A Board - Sheet : 003 (1 / 6) ---------------------53
11.2.15. A Board - Sheet : 003 (2 / 6) ---------------------54
11.2.16. A Board - Sheet : 003 (3 / 6) ---------------------55
11.2.17. A Board - Sheet : 003 (4 / 6) ---------------------56
11.2.18. A Board - Sheet : 003 (5 / 6) ---------------------57
11.2.19. A Board - Sheet : 003 (6 / 6) ---------------------58
11.2.20. A Board - Sheet : 004 (1 / 8) ---------------------59
11.2.21. A Board - Sheet : 004 (2 / 8) ---------------------60
11.2.22. A Board - Sheet : 004 (3 / 8) ---------------------61
11.2.23. A Board - Sheet : 004 (4 / 8) ---------------------62
11.2.24. A Board - Sheet : 004 (5 / 8) ---------------------63
11.2.25. A Board - Sheet : 004 (6 / 8) ---------------------64
11.2.26. A Board - Sheet : 004 (7 / 8) ---------------------65
11.2.27. A Board - Sheet : 004 (8 / 8) ---------------------66
11.2.28. A Board - Sheet : 005 (1 / 5) ---------------------67
11.2.29. A Board - Sheet : 005 (2 / 5) ---------------------68
11.2.30. A Board - Sheet : 005 (3 / 5) ---------------------69
11.2.31. A Board - Sheet : 005 (4 / 5) ---------------------70
11.2.32. A Board - Sheet : 005 (5 / 5) ---------------------71
11.2.33. A Board - Sheet : 006 (1 / 2) ---------------------72
11.2.34. A Board - Sheet : 006 (2 / 2) ---------------------73
11.2.35. A Board - Sheet : 007 (1 / 7) ---------------------74
11.2.36. A Board - Sheet : 007 (2 / 7) ---------------------75
11.2.37. A Board - Sheet : 007 (3 / 7) ---------------------76
11.2.38. A Board - Sheet : 007 (4 / 7) ---------------------77
11.2.39. A Board - Sheet : 007 (5 / 7) ---------------------78
11.2.40. A Board - Sheet : 007 (6 / 7) ---------------------79
11.2.41. A Board - Sheet : 007 (7 / 7) ---------------------80
11.2.42. A Board - Sheet : 008 (1 / 4) ---------------------81
11.2.43. A Board - Sheet : 008 (2 / 4) ---------------------82
11.2.44. A Board - Sheet : 008 (3 / 4) ---------------------83
11.2.45. A Board - Sheet : 008 (4 / 4) ---------------------84
11.2.46. A Board - Sheet : 009 (1 / 11)--------------------85
11.2.47. A Board - Sheet : 009 (2 / 11)--------------------86
11.2.48. A Board - Sheet : 009 (3 / 11)--------------------87
11.2.49. A Board - Sheet : 009 (4 / 11)--------------------88
11.2.50. A Board - Sheet : 009 (5 / 11)--------------------89
11.2.51. A Board - Sheet : 009 (6 / 11)--------------------90
11.2.52. A Board - Sheet : 009 (7 / 11)--------------------91
11.2.53. A Board - Sheet : 009 (8 / 11)--------------------92
11.2.54. A Board - Sheet : 009 (9 / 11)--------------------93
11.2.55. A Board - Sheet : 009 (10 / 11) ------------------94
11.2.56. A Board - Sheet : 009 (11 / 11)------------------- 95
11.2.57. A Board - Sheet : 010 (1 / 3) ---------------------96

TH-LR37G10
4
11.2.58. A Board - Sheet : 010 (2 / 3)----------------------97
11.2.59. A Board - Sheet : 010 (3 / 3)----------------------98
11.2.60. A Board - Sheet : 011 (1 / 4)----------------------99
11.2.61. A Board - Sheet : 011 (2 / 4)-------------------- 100
11.2.62. A Board - Sheet : 011 (3 / 4)-------------------- 101
11.2.63. A Board - Sheet : 011 (4 / 4)-------------------- 102
11.2.64. A Board - Sheet : 012 (1 / 1)-------------------- 103
11.2.65. A Board - Sheet : 013 (1 / 5)-------------------- 104
11.2.66. A Board - Sheet : 013 (2 / 5)-------------------- 105
11.2.67. A Board - Sheet : 013 (3 / 5)-------------------- 106
11.2.68. A Board - Sheet : 013 (4 / 5)-------------------- 107
11.2.69. A Board - Sheet : 013 (5 / 5)-------------------- 108
11.2.70. A Board - Sheet : 014 (1 / 6)-------------------- 109
11.2.71. A Board - Sheet : 014 (2 / 6)---------------------110
11.2.72. A Board - Sheet : 014 (3 / 6)---------------------111
11.2.73. A Board - Sheet : 014 (4 / 6)---------------------112
11.2.74. A Board - Sheet : 014 (5 / 6)---------------------113
11.2.75. A Board - Sheet : 014 (6 / 6)---------------------114
11.2.76. A Board - Sheet : 015 (1 / 3)---------------------115
11.2.77. A Board - Sheet : 015 (2 / 3)---------------------116
11.2.78. A Board - Sheet : 015 (3 / 3)---------------------117
11.2.79. A Board - Sheet : 016 (1 / 2)---------------------118
11.2.80. A Board - Sheet : 016 (2 / 2)---------------------119
11.2.81. A Board - Sheet : 017 (1 / 3)-------------------- 120
11.2.82. A Board - Sheet : 017 (2 / 3)-------------------- 121
11.2.83. A Board - Sheet : 017 (3 / 3)-------------------- 122
11.2.84. A Board - Sheet : 018 (1 / 4)-------------------- 123
11.2.85. A Board - Sheet : 018 (2 / 4)-------------------- 124
11.2.86. A Board - Sheet : 018 (3 / 4)-------------------- 125
11.2.87. A Board - Sheet : 018 (4 / 4)-------------------- 126
11.3. K Board--------------------------------------------------- 127
11.3.1. K Board (1 / 3)-------------------------------------- 127
11.3.2. K Board (2 / 3)-------------------------------------- 128
11.3.3. K Board (3 / 3)-------------------------------------- 129
11.4. P Board--------------------------------------------------- 130
11.4.1. P Board (1 / 7)-------------------------------------- 130
11.4.2. P Board (2 / 7)-------------------------------------- 131
11.4.3. P Board (3 / 7)-------------------------------------- 132
11.4.4. P Board (4 / 7)-------------------------------------- 133
11.4.5. P Board (5 / 7)-------------------------------------- 134
11.4.6. P Board (6 / 7)-------------------------------------- 135
11.4.7. P Board (7 / 7)-------------------------------------- 136
11.5. V Board--------------------------------------------------- 137
11.5.1. V Board (1 / 5)-------------------------------------- 137
11.5.2. V Board (2 / 5)-------------------------------------- 138
11.5.3. V Board (3 / 5)-------------------------------------- 139
11.5.4. V Board (4 / 5)-------------------------------------- 140
11.5.5. V Board (5 / 5)-------------------------------------- 141
12 Exploded View and Replacement Parts List--------- 142
12.1. Exploded View and Mechanical Replacement
Parts List ------------------------------------------------- 142
12.2. Electrical Replacement Parts List------------------ 142
12.2.1. Replacement Parts List Notes ----------------- 142
12.2.2. Electrical Replacement Parts List------------- 143

TH-LR37G10
5
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.2. Touch-Current Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground
such as a water pipe as shown in Figure 1.
3. Use the Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4. Check each exposed metallic part and measure the voltage at each point.
5. The potential at any point (touch current) expressed as voltage U1and U2, do not exceed the following values:
For AC: U1= 35 V (peak) and U2= 0.35 V (peak);
For DC: U1= 1.0 V,
NOTE :
The limit value of U2= 0.35 V (peak) for AC and U1= 1.0 V for DC correspond to the values 0.7 mA (peak) AC and 2.0 mA
DC.
The limit value U1= 35 V (peak) for AC correspond to the value 70 mA (peak) AC for frequencies greater than 100 kHz.
6. Should a measurement be out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.

TH-LR37G10
6
1.3. LH89 Chasis Block Diagram
HOT COLD
(LED:5 TIMES)
(LED:9 TIMES)
(LED:8 TIMES)
(LED:1 TIMES)
(LED:7 TIMES)
(LED:3 TIMES)
(LED:6 TIMES)
(LED:4 TIMES)
+
A12
A10
STB+5V
L,R
L,R
SD BOOT
ZWEI
PWM
PANEL
INV SOS
DTV+12V
PANEL
A12
HDMI2
A17
IIC3
MAIN Y/U/V
HDMI3
CLOCK GEN
A11
LED
HDMI3
SUB+1.2V
AV1
DTV-L,R
MONITOR OUT
HDMI1
SD CARD
DCDC
SUB+5V
STB_RESET
SUB+3.3V
SUB+3.3V
A-BOARD
A03
AUIDO AMP
HDMI Receiver
A/D converter
STB+3.3V
VIDEO
AUDIO PROCESSOR
HDMI2
LOSD
REMOTE
27MHz
V-BOARD
SUB+3.3V
74MHz
SUB+3.3V
LED
LVDS
AV2
EEPWP
V,C,V
EEPROM
R,G,B
REMOTE CONTROL
OVP_DET
SD CARD I/F
V,Y,PB,PR
HEADPHONE
GenX8
A01
BACK LIGHT
SUB_ON
RESET
STB Micom
SOUND SOS
27MHz
INV SOS
AV3
SOS
SUB+9V SENSE SUB+5V SENSE
Serial
FLASH MEMORY
L,R
SUB+1.8V
HP
V10
INVERTER CIRCUIT
PANEL+12V
FOR FACTORY USE
DTV+12V
SUB+5V
REMOTE
RF
CONTROL
OPT OUT
STB+3.3V
IECOUT
AUDIO_RST
SUB+3.3V SENSE
DCDC
L,R
FOR FACTORY USE
HDMI1
Tuner
MAIN+3.3V SENSE
DDR2 SDRAM
LED
RF
TV_SOS
SPEAKER
KEY
SUB+1.8V
EEPROM
DTV+12V SENSE
PC
SUB+9V
ZW_PLL3.3V
SUB_ON
RESET
OPT
(MAIN MCU+VIDEO SIGNAL PROCESSOR)
Digital video signal
AV SW
Peaks Lite2p
A07
LCD PANEL
FOR FACTORY USE
SBO2 SBI2
DTV Digital Auido
SUB+1.2V
A20
V,Y,PB,PR
MONITOR L,R
ON
+5VS
STB+5V
POWER SW
OPERATION BUTTON
K-BOARD
AC CORD
PROCESS VOLTAGE RECTIFIER
P1
5V
+17V
P5
+5VS
+12V
+17V
DTV+12V
TUNER+6V
P2
FILTER
STB
RELAY
P4
P6
PHOTO COUPLER
SUB_ON
P-BOARD
K01
MONITOR V
HDMI4 HDMI4
SIF.AM
SIF.AM
DVB CVBS
HOT COLD
(LED:5 TIMES)
(LED:8 TIMES)
(LED:1 TIMES)
(LED:7 TIMES)
(LED:3 TIMES)
(LED:6 TIMES) (LED:4 TIMES)
(LED:9 TIMES)
INVERTER CONTROL
INVERTER CONTROL
PWM CONTROL
PWM CONTROL

TH-LR37G10
7
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-
effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the
incidence of component damage caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminium foil to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it (most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or
comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices (otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)
sufficient to damage an ES device).

TH-LR37G10
8
3 About Lead Free Solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead Solder and PbF will refer to Lead Free Solder.
The Lead Free Solder (PbF) used in our manufacturing process and discussed below is (Sn+Ag+Cu).
Those are Tin (Sn), Silver (Ag) and Copper (Cu), although other types are available.
This model uses PbF in its manufacture due to environmental conservation issues. For service and repair work, we would suggest
the use of PbF as well, although Pb may be used.
PCBs manufactured using lead-free will have the “PbF within a leaf Symbol” stamped on their back.
Caution
• PbF has a higher melting point than that of standard solder. Typically the melting point is 50 ~ 70°F (30~40°C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20°F (370 ± 10°C).
• PbF will tend to splash when heated too high (about 1100°F or 600°C).
If you must use Pb solder, please completely remove all of the PbF on the pins or solder area before applying Pb. If this is not
practical, be sure to heat the PbF until it melts, before applying Pb.
• After applying PbF to double layered boards, please check the component side for excess solder which may flow onto the
opposite side (see Figure 2).
Figure 2
Suggested PbF
There are several kinds of PbF available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu
(tin, copper) and Sn+Zn+Bi (tin, zinc, bismuth) solders can also be used.
Figure 3

TH-LR37G10
9
4 Power LED Blinking Timing
1. Subject
Information of LED Flashing timing.
2. Contents
When an abonormality has occurred in the unit, the protection circuit operates and resets to standby mode. At this time, the
defective block can be identified by the number of blinking of the Power LED on the front panel of the unit as follow:
Blinking times Contents
1 Lamp short circuit protection
Lamp open protection
Arc protection
2 Cooling fan SOS = incomplete connection - no function mode.
3 P board 30V / 18V / 9V decreased / short circuit detection.
4 DTV12V decreased / short circuit , main convertor stop detection.
5 Sub 5V decreased / short circuit detection.
6 Sub 5V decreased / short circuit detection. (same as 5 times LED blinking)
7 Sub 3.3V decreased / short circuit detection.
8 Sub 5V decreased / short circuit detection. (same as 5 times LED blinking)
9 Audio amp SOS.
10 HQ1 incomplete connection, no function mode.
13 When peaks communication error SOS.

TH-LR37G10
10
5 Chassis Board
5.1. Chassis MTG Installation
1. Stick the GASKET to A-PB-MTG METAL R (back side).
2. Put A-PB-MTG METAL S/L/R on the LCD PANEL.
3. Fix them with SCREW.
4. Insert the CLAMPER.
5. Stick the P PCB BARRIER.

TH-LR37G10
11
5.2. Chassis Screw Fixing
1. Setting the SUPPORT MOLD A on the P-PCB.
2. Put the P-PCB, A-PCB on the A-PB-MTG METAL.
3. Fix them with SCREWS.
4. Setting the CLAMPER.

TH-LR37G10
12
6 Location of Controls and Components
6.1. Wire Dressing
1. Wiring No. 1 ~ No.7
2. Remove dust of terminal of LVDS and PB connector. (by ion blow) Pos. A11
3. Insert LVDS into A11.
Wire Clamper
123456789
No.1 A10 ~ V10
No.2 A01 ~ K01
No.3 A12 ~ SP(L)
No.4 A12 ~ SP(R)
No.5 LCD ~ P5
No.6 LCD ~ P6
No.7 A20 ~ P4

TH-LR37G10
13
7 Disassembly and Assembly Instructions
7.1. AC Cord Dressing - 1
1. Clamp plug with clamper.
2. Insert beads 3pcs. And slide down to lower hole.

TH-LR37G10
14
7.2. AC Cord Dressing - 2

TH-LR37G10
15
7.3. AC Cord Dressing - 3
1. Clamp CORD with CLAMPER.
2. Clamp plug to BACK COVER.
3. Insert beads 3pcs. And slide down to lower hole.

TH-LR37G10
16
7.4. AC Cord Bracket Installation
1. Put on the AC CORD BRACKET on the CABINET.
2. Fix the AC CORD BRACKET with SCREW.
3. AC CORD BARRIER setting.
4. Insert AC CORD connector into P-PCB connector.
5. Clamp the AC CORD.
6. Insert AC CORD bushing into the AC CORD BRACKET.

TH-LR37G10
17
7.5. VESA Metal And Bottom MTG Installation
1. Assemble LCD top mtg (L, R), vesa metal (upper) and fix them with screw.
2. Put on the VESA METAL ASSY on the LCD PANEL.
3. Fix the VESA METAL ASSY with SCREW.
1. LCD BTM MTG on the LCD PANEL.
2. Fix LCD BTM MTG with SCREW.

TH-LR37G10
18
7.6. LED Panel Installation
1. Fix SMOKE SHEET on LED PANEL.
2. Fix LED PANEL on CABINET.
3. Wire connecting. (V10)
4. Put V-PCB on CABINET.
5. Fix them with SCREW.
6. Insert the CLAMPER.

TH-LR37G10
19
7.7. Control Panel Assembly Installation
1. Put CONTROL PANEL ASSY on the CABINET.
2. Fix the CONTROL PANEL with SCREWS.

TH-LR37G10
20
7.8. Control Panel Support Installation
1. Put CONTROL PANEL SUPPORT METAL A&B on the CABINET.
2. Fix them with SCREW.