Panasonic WJSX650 - SWITCHER User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Matrix Switcher WJ-SX
650
OPERATE
OPERATE LED WILL BLINK
IF COLLINGFAN MALFUNCTIONS
Matrix Switcher
Operating Instructions
Model Nos. WJ-SX650 Series

2
The serial number of this product may be found on the sur-
face of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the litera-
ture accompanying the appliance.
Power disconnection. Unit with or without
ON-OFF switches have power supplied to
the unit whenever the power cord is inserted
into the power source; however, the unit is
operational only when the ON-OFF switch is
in the ON position. The power cord is the
main power disconnect for all units.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CARE-
FULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement
fuse has a rating of 5 amp and that it is approved by ASTA or BSI to
BS1362.
Check for the ASTA mark Hor the BSI mark Gon the body of the
fuse.
If the plug contains a removable fuse cover you must ensure that it is
refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement
cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic
Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCK-
ET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE
CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown
below.
If in any doubt please consult a qualified electrician.
WARNING: This apparatus must be earthed.
IMPORTANT
The wires in this mains lead are coloured in accordance with the follow-
ing code.
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to
the terminal in the plug which is marked with the letter Eor by the earth
symbol Ior coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in
the plug which is marked with the letter Nor coloured black.
The wire which is coloured brown must be connected to the terminal
in the plug which is marked with the letter Lor coloured red.
How to replace the fuse
Open the fuse compartment with
a screwdriver and replace the fuse
and fuse cover.
For U.K.
FUSE
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
• This apparatus must be earthed.
• Apparatus shall be connected to a mains socket outlet with
a protective earthing connection.
• The mains plug or an appliance coupler shall remain readily
operable.
• To prevent fire or electric shock hazard, do not expose this
apparatus to rain or moisture.
• The apparatus should not be exposed to dripping or splash-
ing and that no objects filled with liquids, such as vases,
should be placed on the apparatus.
• All work related to the installation of this product should be
made by qualified service personnel or system installers.
• The connections should comply with local electrical code.
We declare under our sole responsibility that the product to which this
declaration relates is in conformity with the standards or other normative
documents following the provisions of Directives 2006/95/EC and
2004/108/EC.
Nosotros declaramos bajo nuestra única responsabilidad que el
producto a que hace referencia esta declaración está conforme con las
normas u otros documentos normativos siguiendo las estipulaciones de
las directivas 2006/95/CE y 2004/108/CE.
Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a
cui si riferisce la presente dichiarazione risulta conforme ai seguenti
standard o altri documenti normativi conformi alle disposizioni delle
direttive 2006/95/CE e 2004/108/CE.
Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich
diese Erklärung bezieht, mit der folgenden Normen oder normativen
Dokumenten übereinstimmt. Gemäß den Bestimmungen der Richtlinie
2006/95/EC und 2004/108/EC.
Nous déclarons sous note seule responsabilité que le produit auquel se
réfère la présente déclaration est conforme aux normes ou autres
documents normatifs conformément aux dispositions des directives
2006/95/CE et 2004/108/CE.
Wij verklaren als enige aansprakelijke, dat het product waarop deze
verklaring betrekking heeft, voldoet aan de volgende normen of andere
normatieve documenten, overeenkomstig de bepalingen van Richtlijnen
2006/95/EC en 2004/108/EC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med standarder eller
andre normative dokumenter i følge bestemmelserne i direktivene
2006/95/EC og 2004/108/EC.
Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken
denna deklaration hänvisar är i överensstämmelse med
standarddokument, eller andra normativa dokument som framställs i
direktiv nr. 2006/95/EC och 2004/108/EC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus
koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja,
jotka noudattavat direktiivien 2006/95/EC ja 2004/108/EC säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen
gjelder for, er i overensstemmelse med følgende normer eller andre
normgivende dokumenter som følger bestemmelsene i direktivene
2006/95/EC og 2004/108/EC.

3
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
S3125A

4
CONTENTS
Important Safety Instructions ............................................ 3
Limitation of Liability ........................................................... 5
Disclaimer of Warranty ....................................................... 5
Trademarks and Registered Trademarks ........................... 5
Precautions ......................................................................... 6
About These Operating Instructions ................................... 7
Preface ............................................................................... 8
Features .............................................................................. 8
Major Operating Controls and Their Functions ................... 9
■WJ-SX650 Matrix Switcher/
WJ-SX650U Card Cage ................................................ 9
■Video Input Board WJ-PB65C32 ................................ 11
■Video Output Board WJ-PB65M16 ............................. 12
■Monitor Display Information ........................................ 13
■System Controller Display Information ....................... 14
Installations ....................................................................... 16
■Checking Board Composition ..................................... 16
■Switch Settings for Video Input Main Board ............... 17
■Switch Settings for Video Output Main Board ............. 18
■Mounting Video Input and Output Boards ................... 19
■Board Mounting Procedure ......................................... 20
■Installing the Main Unit ............................................... 21
Connections ...................................................................... 22
■Basic System Connections ......................................... 23
■Expanded System Connections .................................. 24
■Card Cage Connections ............................................. 26
■Camera Connections .................................................. 27
■RS-485 Camera Connections ..................................... 27
■Monitor Connections ................................................... 29
■PC Connection ............................................................ 29
■Recorder Connection .................................................. 30
■Recorder Settings ....................................................... 35
■System Controller Connection .................................... 35
■Alarm Sensor Connections ......................................... 37
■External Device Connections ...................................... 37
■System Status Check ................................................. 38
Setup Procedure ............................................................... 39
WJ-SX650 Series Administrator Console ......................... 41
■System Requirements of a PC ................................... 41
■Installation and Uninstallation ..................................... 41
■Starting Up .................................................................. 42
■Window Details ........................................................... 42
■Tooltip Details ............................................................. 43
Factory Default Settings ................................................... 46
■Factory Default Settings of WJ-SX650 Series
Administrator Console ................................................ 46
■Factory Default Settings of SETUP MENU ................. 48
Setup Menu (OSD) ........................................................... 49
■Basic Operations ........................................................ 49
■TIME & DATE ............................................................. 50
■ALARM ....................................................................... 50
■RECORDER ............................................................... 51
■SYSTEM ..................................................................... 53
■INFORMATION ........................................................... 55
■LANGUAGE ................................................................ 55
Login and Logout .............................................................. 56
■Operator Registration ................................................ 56
■Power-on/off ............................................................... 57
■Operation Start (Login) ............................................... 57
■Operation End (Logout) .............................................. 57
■Operation Start/End (Auto Login/Logout) ................... 57
Monitor Control ................................................................. 58
■Monitor Selection ........................................................ 58
■Monitor Lock ............................................................... 58
Camera Control ................................................................ 59
■Camera Selection ....................................................... 59
■Camera Selection Recall ............................................ 59
■Preset Position Control ............................................... 59
■All Cameras Control .................................................... 60
Recorder Control .............................................................. 61
■Playback ..................................................................... 61
■Manual Recording ....................................................... 61
■Multiscreen Display ..................................................... 61
■Search Playback ......................................................... 61
■Playing the Latest Recorded Image ............................ 61
■Recorder Control End ................................................. 62
■Recorder Selection ..................................................... 62
Running Sequence ........................................................... 63
■Descriptions of Sequence ........................................... 63
■Tour Sequence ........................................................... 65
■Group Sequence/Preset ............................................. 65
■Sequence Pause ........................................................ 66
■Sequence Stop ........................................................... 66
Alarm Descriptions ............................................................ 67
■Alarm Occurrence ....................................................... 67
■Alarm Modes ............................................................... 68
■Video Loss .................................................................. 68
Alarm Control .................................................................... 69
■Alarm Acknowledgement (ACK) ................................. 69
■Camera Control .......................................................... 69
■Alarm Picture Change ................................................. 69
■Alarm Individual Reset ................................................ 69
■Alarm Monitor Reset ................................................... 69
■Alarm All Reset ........................................................... 69
■Return to Alarm Mode Status ..................................... 70
■Alarm Suspension ....................................................... 70
■Alarm History Display ................................................. 70
Timer Descriptions ............................................................ 72
■Timer Event ................................................................ 72
■Camera Event ............................................................. 72
Terminal Mode Operation ................................................. 74
■Lists of Operations and Functions .............................. 74
■Menu Flow (WV-CU950/650) ...................................... 85
Operation (Other than Terminal Mode) ............................. 86
■PS·Data Mode Operations .......................................... 86
■Connections of Matrix Switchers (WJ-SX650 Series)
and a PS·Data System Controller ............................... 87
■
Controlling from a Web Browser Accessing a Recorder .....87
■Controlling from a PC ................................................. 87
Glossary ............................................................................ 88
Troubleshooting ................................................................ 90
■Matrix Switcher WJ-SX650 Series............................... 90
■WJ-SX650 Series Administrator Console .................... 94
■Power Cord, Connectors, and Power Plug ................. 95
Specifications .................................................................... 96
■Matrix Switcher WJ-SX650 Series................................96
■Card Cage WJ-SX650U................................................97
■Video Input Board WJ-PB65C32 ..................................97
■Video Output Board WJ-PB65M16 ...............................97
■Expansion Cable Kit WJ-CA65L20K/WJ-CA65L07K....98
■D-sub/BNC Video Cable WJ-CA68...............................98
Standard Accessories ....................................................... 98

5
Limitation of Liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WAR-
RANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY, FITNESS FOR ANY PAR-
TICULAR PURPOSE, OR NON-INFRINGEMENT OF THE
THIRD PARTY’S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INAC-
CURACIES OR TYPOGRAPHICAL ERRORS. CHANGES
ARE ADDED TO THE INFORMATION HEREIN, AT ANY
TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION
AND/OR THE CORRESPONDING PRODUCT (S).
Trademarks and Registered Trademarks
• Microsoft, Windows and Windows XP are registered
trademarks of Microsoft Corporation in the U.S. and/or
other countries.
• Intel and Pentium are registered trademarks of Intel
Corporation or its subsidiaries in the United States and
other countries.
• Other company names and product names appearing
in this document are registered trademarks or trade-
marks of the company concerned.
Disclaimer of Warranty
IN NO EVENT SHALL MATSUSHITA ELECTRIC INDUSTRI-
AL CO., LTD. BE LIABLE TO ANY PARTY OR ANY PER-
SON, EXCEPT FOR CERTAIN WARRANTY PROGRAM
OFFERED BY THE LOCAL DEALER OF PANASONIC, FOR
THE CASES INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIM-
ITATION, DIRECT OR INDIRECT, SPECIAL, CONSE-
QUENTIAL OR EXEMPLARY, ARISING OUT OF OR
RELATING TO THE PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION
OF THE USER;
(3) UNAUTHORIZED DISASSEMBLY, REPAIR OR MODIFI-
CATION OF THE PRODUCT BY THE USER;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN
IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON
OR CAUSE INCLUDING ANY FAILURE OR PROBLEM
OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYS-
TEM COMBINED BY THE DEVICES OF THIRD PARTY;

6
Precautions
CAUTION: These servicing instructions are for use by qual-
ified service personnel only. To reduce the risk of elec-
tric shock do not perform any servicing other than that
contained in the operating instructions unless you are
qualified to do so.
• Do not block the ventilation opening or slots on the
cover.
To prevent the apparatus from overheating, place it at
least 5 cm {2 inches} away from the wall.
• Do not drop metallic parts through slots.
This could permanently damage the apparatus. Turn
the power off immediately and contact qualified service
personnel for service.
• Do not attempt to disassemble the apparatus.
To prevent electric shock, do not remove screws or
covers.
There are no user-serviceable parts inside. Contact
qualified service personnel for maintenance.
• Do not strike or give a strong shock to the unit.
It may cause damage or allow water to enter the unit.
• Do not expose the apparatus to water or moisture.
Do not try to operate it in wet areas.
Take immediate action if the apparatus gets wet. Turn
the power off and refer servicing to qualified service
personnel. Moisture can damage the apparatus and
also cause electric shocks.
• Built-in backup battery
Before the first use, charge the built-in backup battery
(lithium battery) by turning on the power for 48 hours or
more. If it is not charged enough, in a case where the
power goes down, the internal clock may keep bad
time or the operative condition may be different to that
before the electric power failure.
The built-in battery life is approximately 5 years as an
indication of replacement. (This is just an indication of
replacement. We are not providing any guarantee of the
built-in battery lifetime. Replacement cost of the built-in
battery is not covered by the warranty even if it needs
to be done within the warranty period.) Ask the shop
where you purchased the unit when replacement of the
battery is required.
• Cooling Fan
Turn the power off when cleaning the unit. Otherwise it
may cause injuries.
The cooling fan will operate for approximately 30 000
hours. Replacement costs of the cooling fan are not
covered by the warranty even if it needs to be done
within the warranty period.
• Cleaning
Turn the power off when cleaning the unit. Otherwise it
may cause injuries.
Do not use strong or abrasive detergents when clean-
ing the apparatus body.
Use a dry cloth to clean the apparatus when it is dirty.
When the dirt is hard to remove, use a mild detergent
and wipe gently.
• Do not operate the apparatus beyond its specified
temperature, humidity, or power source ratings.
Use the apparatus under conditions where tempera-
tures are between –10 °C and + 50 °C {14 °F to 122 °F},
and humidity below 90 %.
The apparatus may not work properly after turning on in
a cold atmosphere between –10 °C and 0 °C {14 °F to
32 °F}. Wait approximately 10 minutes until the inside
temperature has risen to 0 °C {32 °F}, it can work prop-
erly.
The input power source for this apparatus is 220 V to
240 V AC, 50 Hz.
• Place the unit horizontally on a level surface. Do not
place the unit in an upright position. When stacking
multiple units, clear a space of more than 5 cm {2
inches} from both sides, the top, the bottom and the
rear of the units.
• Pay attention to static electricity
Make certain to keep boards inside the anti-static sack
until it is installed.
Put your hand on a metallic surface, other than the
boards to discharge static electricity before installation.
Do not touch components mounted on the boards
directly by hand.
Hold only both edges of the boards when installing.
• Do not use any power cord other than the one sup-
plied.
Use the power cord that is suited to your locality.
• Only use the apparatus indoors.
Do not install it in places where the apparatus is
exposed to sunlight for long periods of time or near air
conditioning equipment. This will cause deformation,
discolouration, breakdown or malfunction.
• We recommend that you make a note of your set-
tings and save them. This will help when you are
required to change the system configuration, or
when unexpected trouble or failure occurs.
• Distributing, copying, disassembling, reverse com-
piling, reverse engineering, and also exporting in
violation of export laws of the software provided
with this product, is expressly prohibited.

7
About These Operating Instructions
These operating instructions are classified roughly as fol-
lows:
• Operations (pp. 55 to 86)
Contains how to operate the system. These descrip-
tions are intended for operators.
Note: Before operation, be sure to read safety instruc-
tions on p. 3 IMPORTANT SAFETY INSTRUCTIONS
and p. 6 PRECAUTIONS.
• Preparations (pp. 16 to 54)
Contains the required preparations including installa-
tion, connections, and setup procedures. These
descriptions are intended for installers and system
administrators.
This document uses the following terms for classifica-
tion of devices.
The (This ) unit: Matrix Switcher WJ-SX650
Video input board: Video Input Board WJ-PB65C32
Video output board: Video Output Board WJ-PB65M16
Recorder: Digital Disk Recorder WJ-HD300/WJ-HD300
A Series, WJ-RT416 Series
Classification of digital disk recorders are as follows.
Term
WJ-HD300 Series
WJ-HD300A Series
WJ-RT416 Series
Model Nos.
WJ-HD316, WJ-HD309
WJ-HD316A, WJ-HD309A
WJ-RT416
Remarks on Model Nos.
Begins with "WJ-HD316".
Begins with "WJ-HD316A".
–

8
Features
• Up to 256 cameras, 32 monitors connectable
• Remote control of optional external devices
If you connect System Controller WV-CU950, WV-
CU650, WV-CU360C and/or WV-CU360CJ to this prod-
uct, remote control of cameras, lenses, pan/tilt heads,
and recorders (Digital Disk Recorder*) will be available.
* Refer to “Readme.txt” on the supplied CD-ROM for
details on model numbers.
If you connect a personal computer (PC) to this prod-
uct, control and system setup with WJ-SX650 Series
Administrator Console will be available.
• Authentication by user ID's, passwords, and level
settings.
User ID's and passwords are assignable to users to
prevent inappropriate operations. In addition, the set-
tings of level, camera access, and recorder access can
determine available functions, cameras, and recorders
for each user.
• Images of two or more cameras can be displayed on
one monitor.
Spot mode: A selected camera image is continuously
displayed on a selected monitor.
Sequence mode: Images of two or more cameras are
sequentially displayed on a desired monitor (or
monitors).
• Timer event and camera event can be scheduled.
Note: Refer to p. 72 for details on timer event and cam-
era event.
• Alarm operation and alarm event can be scheduled.
Notes:
• Refer to p. 69 for details on alarm operation.
• Refer to p. 67 for details on alarm event.
• With recorder connection, recorder control such as
recording and playback are available.
Camera images can be recorded.
Recorded images can be played back.
Camera images can be displayed in multiscreen seg-
ments.
Preface
Matrix Switcher WJ-SX650 Series (or SX650 Series) are
designed for a surveillance control system. WJ-SX650
Series (or SX650 Series) is the general term of following
models.
Matrix Switcher WJ-SX650 (Video Input Board WJ-
PB65C32 x 1 and Video Output Board WJ-PB65M16 x 1
have been installed.)
Card Cage WJ-SX650U (For additional installation of video
input boards and video output boards)
Video Input Board WJ-PB65C32
Video Output Board WJ-PB65M16
Expansion Cable Kit WJ-CA65L20K/WJ-CA65L07K
D-sub/BNC Video Cable WJ-CA68

9
Major Operating Controls and Their Functions
■WJ-SX650 Matrix Switcher/WJ-SX650U Card Cage
●Front View
qOperation Indicator (OPERATE)
• This indicator is lighting while power is supplied to the
unit.
• This indicator blinks when the cooling fan has a trouble.
(Refer to p. 90.)
wFront Panel Fixing Screws
Before you press the power switch or install boards into
the expansion slot, these screw are removed to detach
the front panel
ePower Switch
rExpansion Slot
Optional video input or output main board is installed.
(Video Input Board WJ-PB65C32 or Video Output Board
WJ-PB65M16)
For WJ-SX650U, optional video input main board is
installed. (Video Input Board WJ-PB65C32)
tVideo Input Board*
This is a video input main board. This board controls
cameras and alarm sensors (door switch, etc.).
Note: Refer to p. 11 WJ-PB65C32 Video Input Board for
details.
yVideo Output Board*
This is a video output main board. This board controls
monitors and alarm output signals.
Note: Refer to p. 12 WJ-PB65M16 Video Output Board
for details.
* For WJ-SX650U, tand yare expansion slots.
OPERATE
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
Matrix Switcher WJ-SX
650650
PULL
POWER
ON
OFF
RESET
No.
MODE
RESET
TEST
MODE
Normally, do not touch.
(Reserved for service personnel)
e
t
<Front panel detached>
y
r
<Front panel attached>
w
q
This is the illustration of WJ-SX650.

10
uVideo Input Board Rear Panels*
These are video input rear boards.
Notes:
• Refer to p. 11 WJ-PB65C32 Video Input Board for
details.
• When installing a set of video output board into the
expansion slot of WJ-SX650, you will remove the IN
B-3 board, and install the OUT X-3 board.
iExpansion Slot
For WJ-SX650, optional video input or output rear
boards are installed. (Video Input Board WJ-PB65C32
or Video Output Board WJ-PB65M16)
For WJ-SX650U, optional video input rear boards are
installed. (Video Input Board WJ-PB65C32)
oVideo Output Board Rear Panels
These are video output rear boards.
Note: Refer to p. 12 WJ-PB65M16 Video Output Board
for details.
!0 AC Inlet Socket (AC IN)
When using the unit, you will plug the power cord (sup-
plied as a standard accessory) into this socket and
connect the cord to an AC outlet.
!1 Signal Ground Terminal (SIGNAL GND)
●Rear View
VIDEO OUT 3
VIDEO OUT 4 VIDEO OUT 2
MODEMODEMODEMODE
3
C
IN X-2
IN X-1
VIDEO OUT 1
ALARM IN
1
16
32
15
31 30
14 13
29 28
12 11
27 26
10 9
25
CAMERA IN
24
87
23 22
65
21
2
B
1
2
3
20
43
19 18
21
17
DATA DATA
EXTENSION 1
TERM.
OFF ON
OUT IN
OUT X-3
OUT X-2
OUT X-1
1234
AC IN
3
2
1
A
12345678
MONITOR OUT
910111213141516
ALARM OUT 2 ALARM OUT 1
SERIAL
VS OUT
VS IN
VS OUT
(THRU)
EXTENSION 3 IN EXTENSION 2 IN
4
MODE
RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
4
MODE
RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN B-3
TERM.OFF
ON
MODE
TERM.ON
MODE
SIGNAL GND
DATA 4
HDR4/TMNL8
HDR2/TMNL4
DATA 3
HDR3/TMNL7
HDR1/TMNL3
DATA 2
TMNL6
TMNL2
DATA 1
TMNL5
TMNL1/PS DATA
Video Output Board 2
Video Output Board 1
SIGNAL GND
Video Output Board 1 Only
ON
4-Line
RS485(CAMERA) SET UP
MODE
ON
4-Line
MODE
3
C
1
2
B
1
2
3
AC IN
3
2
1
A
EXTENSION 3 IN EXTENSION 2 IN
4
MODE
RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN C-3
SIGNAL GND
SIGNAL GND
ON
4-Line
RS485(CAMERA) SET UP
MODE
ON
4-Line
MODE
4
MODE
RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
21
IN B-3
EXTENSION 3 OUT EXTENSION 2 OUT
EXTENSION 1
TERM.
OFF ON
OUT IN
MODE
RS485 (CAMERA) RS485 (CAMERA)
MODE MODE MODE
IN A-3
!1
!1 !1
<WJ-SX650> <WJ-SX650U>
u
!0 i!0
u
i
o

11
RESET
No.
MODE
qwe
VIDEO OUT 3
VIDEO OUT 4 VIDEO OUT 2
IN X-2
VIDEO OUT 1
ALARM IN
IN X-1
16
32
15
31 30
14 13
29 28
12 11
27 26
10 9
25
CAMERA IN
24
87
23 22
65
21 20
43
19 18
21
17
EXTENSION 3 IN EXTENSION 2 IN
4
MODE
RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
2 1
IN C-3
IN C-3 board
IN X-2 board
IN X-1 board
uu
i
!0
!1
43
MODE
RS485 (CAMERA) RS485 (CAMERA)
MODE MODE MODE
21
IN B-3
MODE
RS485 (CAMERA) RS485 (CAMERA)
MODE MODE MODE
4321
EXTENSION 1
TERM.
OFF ON
OUT IN
IN A-3
EXTENSION 3 OUT EXTENSION 2 OUT
IN A-3 board
IN B-3 board
tuur
i
y
oy
■Video Input Board WJ-PB65C32
Video input board is composed of a main board (installed into the front side) and rear boards (x 3)(installed into the rear side).
●Front View
qBoard Number Switch (No.)
Refer to p. 17 Switch Settings for Video Input Main
Board for details.
wInput Mode Selection Switches (MODE)
Set all switches to OFF.
●Rear View
IN A-3/IN B-3/IN C-3 board
Note: These boards are originally installed into WJ-SX650
and WJ-SX650U, and not supplied to optional video input
boards. (IN A-3 board is installed into WJ-SX650U only.)
rExtension Ports 1 (EXTENSION 1: IN, OUT)
These ports connect to an optional card cage.
tTermination Selector (TERM: ON, OFF)
Turns on or off the line termination of r.
yExtension Ports 2, 3 (EXTENSION 2, 3: IN, OUT)
Each port connects to an optional card cage.
uRS-485 Camera Ports 1 to 4 (RS485 (CAMERA) 1 to
4)
These ports connect to RS-485 cameras.
iRS-485 Camera Mode Switches 1 to 4 (MODE 1 to 4)
These switches are moved to change the communica-
tion modes of u.
IN X-2 board
oVideo Output Ports 1 to 4 (VIDEO OUT 1 to 4)
These ports loop through video input signals supplied
to !1.
!0 Alarm Input Port (ALARM IN)
Connects to an alarm sensor (door switch, etc.).
IN X-1 board
!1 Camera Input Connectors 1 to 32 (CAMERA IN 1 to
32)
These connectors accept video input signals from cam-
eras or recorders.
eReset Switch (RESET)
This button is pressed to reset this board.
Note: In normal operation, you need not press the but-
ton.

12
■Video Output Board WJ-PB65M16
Video output board is composed of a main board (installed into the front side) and rear boards (x 3)(installed into the rear
side).
●Front View
qOutput Mode Selection Switches (MODE)
Refer to p. 18 Switch Settings for Video Output Main
Board for details.
wReset Switch (RESET)
This button is used only for factory tests. Do not press.
●Rear View
OUT X-3 board
rExtension Ports 1 (EXTENSION 1: IN, OUT)
These ports connect to an optional card cage.
tTermination Selector (TERM: ON, OFF)
Turns on or off the line termination of r.
yData ports 1, 2 (DATA 1, 2)
Each port connects to system controllers.
uData ports 3, 4 (DATA 3, 4)
Each port connects to system controllers or recorders.
iRear Termination MODE Switches 1 to 4 (MODE 1 to
4)
Turns on or off the line termination of yand u.
OUT X-2 board
oMonitor Output Connectors (MONITOR OUT 1 to 16)
These connectors connect to monitors.
OUT X-1 board
!0 Alarm Output Ports 1,2 (ALARM OUT 1, 2)
• Supplies alarm output signals.
• Accepts alarm recover input signals.
• Supplies and accepts the time adjust input and output
signals.
!1 VS Input Connector (VS IN)
Accepts a VS input signal from an external device.
!2 VS Output Loop-thru Connector (VS OUT (THRU))
Loops through VS input signals supplied to !1.
eTest port (TEST)
This port is used only for factory tests. Do not connect
anything.
RESET
TEST
MODE
qwe
OUT X-2
12345678
MONITOR OUT
910111213141516
EXTENSION 1
TERM.
OFF ON
OUT IN
OUT X-3
MODEMODE
DATA
12
MODEMODE
DATA
34
TERM.OFF
ON
MODE
TERM.ON
MODE
DATA 4
HDR4/TMNL8
HDR2/TMNL4
DATA 3
HDR3/TMNL7
HDR1/TMNL3
DATA 2
TMNL6
TMNL2
DATA 1
TMNL5
TMNL1/PS DATA
Video Output Board 2
Video Output Board 1
OUT X-1
ALARM OUT 2 ALARM OUT 1
SERIAL
VS OUT
VS IN
VS OUT
(THRU)
Video Output Board 1 Only
ruy
t
i
o
!0
!1
!3
!4!2
OUT X-3 board
OUT X-2 board
OUT X-1 board

13
■Monitor Display Information
The following are the details on terminal mode operations. For PS·Data operations, refer to p. 86 OPERATION (OTHER THAN
TERMINAL MODE) or the operating instructions of system controllers.
qTime and Date Information
Current time and date are displayed.
During daylight saving time (summer time), "∗" is dis-
played beside the time.
Example: 02/08/2005 ∗20:15:56
Note: While a recorder is being selected, time and date
are not displayed.
wMonitor Status Information
Monitor number
M01 to 32: Monitor number
Note: During monitor lock, monitor number is highlight-
ed.
Controller information
Displays a device that selects and controls the monitor.
K1-1 to 8-4: Terminal mode system controller
(Example: For K8-4, "8" means the DATA port
(TMNL) number and "4" means the controller num-
ber of system controller.)
PSD: PS·Data mode system controller
PC: PC connected to the SERIAL port
/T001 to 128: Timer event
Sequence number
Displays the active sequence number.
T01 to 32: Tour sequence number
G01 to 32: Group sequence number
Note: During sequence pause, "P" is displayed beside
the sequence number.
eCamera Information
Camera number
C001 to 999: Camera number
R01 to 16: Recorder number
Camera title
Displays the registered camera title.
Camera title setting is performed in "Camera" – "Camera
Title" of WJ-SX650 Series Administrator Console.
rEvent Information
TERMINAL001 to 256: Terminal alarm has occurred.
(Example: For TERMINAL001, "001" means the
number of alarm input signal accepted by the
ALARM IN port of video input board.)
CAMERA001 to 999: Camera alarm has occurred.
(Example: For CAMERA001, "001" means the num-
ber of camera supplying an alarm input signal to
the unit.)
RECORDER001 to 999: Recorder alarm has occurred.
(Example: For RECORDER001, "001" means the
number of camera associated with the recorder
supplying an alarm input signal to the unit.)
SERIAL0001 to 1024: Serial alarm has occurred.
(Example: For SERIAL0001, "0001" means the serial
command alarm input number.)
VIDEO LOSS001 to 999: Video loss has occurred.
(Example: For VIDEO LOSS001, "001" means the num-
ber of camera to which video loss has occurred)
SUSPEND: Alarm is suspended.
r
q
w
e
!3 VS Output Connector (VS OUT)
Supplies VS output signals to external devices. While !1
is accepting a VS input signal, !3 supplies an output
signal synchronizing the VS input signal. While !1 is not
accepting the VS input signal, !3 supplies an internal
synchronization output signal.
!4 Serial Port (SERIAL)
Connects to a PC.
Note: When qis set as Video Output Board 2, r, !1,
!2, !3, and !4 are not available.

14
Notes:
• During the alarm acknowledgement (ACK) status (refer
to p. 69), event information is highlighted.
• When two or more alarm events have occurred, "∗" is
displayed beside the event information.
• When an alarm whose display mode setting is OFF
occurs, "#" is displayed beside the event information.
• When auto tracking is scheduled for a camera event, "#"
is displayed beside the camera number.
•qto rcan be displayed or hidden either altogether or
separately. Refer to p. 74 Lists of Operations and
Functions for details.
■ System Controller Display
Information
The following are the details on terminal mode operations.
For PS·Data operations, refer to p. 86 OPERATION (OTHER
THAN TERMINAL MODE) or the operating instructions of
system controllers.
● WV-CU950/650
qMonitor Number
Mon01 to 32: Monitor number
wCamera Number
Cam001 to 999: Camera number
C-P0001 to 9999: Camera position number
eEvent
HDR01 to 16: Recorder number
Pre000 to 256 (Lighting for 3.0 seconds): Preset position
Note: Pre000 is the home position.
T-A0001 to 0256: Terminal alarm
C-A0001 to 0999: Camera alarm
R-A0001 to 0999: Recorder alarm
S-A0001 to 1024: Serial alarm
V-A0001 to 0999: Video loss
rBusy
Busy + monitor number (Blinking)
A selected monitor is controlled by a higher-priority
operator. (Monitor busy)
Note: You cannot control the selected monitor, camera,
and recorder.
Busy + camera/recorder number (Blinking)
A selected camera or recorder is controlled by a high-
er-priority user. (Camera/Recorder busy)
Note: You cannot control the selected camera or
recorder.
tStatus
Alarm (Blinking): Alarm is occurring.
Alarm (Lighting): Alarm is acknowledged. (Refer to p.
69.)
Memory + preset position number (Blinking for 3.0 sec-
onds): Preset position is registered.
ySequence Number
T-Seq01 to 32: Tour sequence number
G-Seq01 to 08: Group sequence number
Note: During sequence pause, "P" is displayed beside
the sequence number.
G-Seq09 to 32: Group preset number
Note: This sign disappears when the camera is con-
trolled.
Invalid (Blinking for 3.0 seconds): You have entered a
wrong value.
Not Avail (Blinking for 3.0 seconds):
• You cannot select a monitor because of lower priori-
ty.
• You have tried to activate a group sequence or
group preset on a monitor not assigned.
Prohibited (Blinking for 3.0 seconds): You have tried an
operation restricted by the operator's setting.
Alarm Buzzer/Button Buzzer Setting
With the setting activated:
• Alarm buzzer can sound when alarms occur.
• Button buzzer can sound when a button is pressed or
an error message (Invalid, Prohibited, Level1 Fixed,
etc.) is displayed on the LCD.
Refer to the operating instructions of system controller
for settings.
tyr
qw e

15
● WV-CU360C/CJ
qMonitor number
01 to 32: Monitor number
wCamera/recorder/sequence number
001 to 999: Camera number
H01 to 16: Recorder number
t01 to 32: Tour sequence number
r01 to 08: Group sequence number
Note: During sequence pause, "P" is displayed instead
of "t" and "r".
r09 to 32: Group preset number
Note: This sign disappears when the camera is con-
trolled.
eEvent
The following signs appear to indicate events on the
LED display.
A0001 to 0256 (Blinking): Terminal alarm
A0001 to 0999 (Blinking): Camera alarm
A0001 to 0999 (Blinking): Recorder alarm
A0001 to 1024 (Blinking): Serial alarm
A0001 to 0999 (Blinking): Video loss
Note: During the alarm acknowledgement (ACK) status
(refer to p. 69), these signs change to steady light.
Pt000 to 256 (Lighting for 3.0 seconds): Preset position
Note: Pre000 is the home position.
Pr001 to 256 (Lighting for 3.0 seconds): Preset position
is registered.
rIndicators
When the MONITOR and BUSY indicators are light-
ing: A selected monitor is controlled by a higher-
priority user. (Monitor busy)
Note: You cannot control the selected monitor, camera,
and recorder.
When the CAMERA and BUSY indicators are light-
ing: A selected camera or recorder is controlled by
a higher-priority user. (Camera/Recorder busy)
Note: You cannot control the selected camera or
recorder.
When the PROHIBITED indicator is lighting:
• You have entered a wrong value.
• You have tried to activate a group sequence or
group preset on a monitor not assigned.
• You have tried an operation restricted by the opera-
tor's setting.
qw
r
BUSY PROHIBITED
MONITOR CAMERA

16
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
The following is the installation flow of this unit.
•Checking Board Composition
•Switch Settings for Video Input Main Board (Refer to p. 17.)
•Switch Settings for Video Output Main Board (Refer to p. 18.)
•Mounting Video Input and Output Boards (Refer to p. 19.)
•Board Mounting Procedure (Refer to p. 20.)
•Installing the Main Unit (Refer to p. 21.)
■Checking Board Composition
By mounting additional video input and output boards, up to 256 cameras and 32 monitors can be connected to this unit. You
will choose one of the composition types described in the following diagram. Check how many video input boards, video out-
put boars, and card cages are required, according to the number of cameras and monitors.
Note: Refer to p. 19 for the figures describing the composition types.
Notes:
• When using 9 or more recorders, 2 sets of additional
video output board are required even if you use 16 or
less monitors.
• External monitors directly connected to recorders can
be excluded from the total number of monitor in the dia-
gram.
• When connecting monitors directly to recorders, the
total numbers of these recorders can be excluded from
"Total number of cameras and recorders" in the dia-
gram.
• Use the following models for system expansion.
Video input board: WJ-PB65C32
Video output board: WJ-PB65M16
Card Cage: WJ-SX650U
• To connect Card Cage WJ-SX650U, Expansion Cable
Kit WJ-CA65L07K (Option) or WJ-CA65L20K (Option) is
required.
• To record camera images by using a recorder, D-
sub/BNC Video Cable WJ-CA68 (Option) is required.
• The maximum set numbers of additional boards are as
follows.
Video input board: Max. 7 sets
Video output board: Max. 1 sets
Board sets exceeding these total numbers cannot be
mounted even some expansion slots are unused.
Installations
Total numbers of
cameras and
recorders
1 to 32
Total number of
monitors
Additional sets of
video input board
Additional sets of
video output
board
Additional card
cages
Composition type
(Refer to p. 19.)
1 to 16 0 0 0 Type 1
17 to 32 0 1 0 Type 2
33 to 64 1 to 16 1 0 0 Type 3
17 to 32 1 1 1 Type 4
65 to 96 1 to 16 2 0 1 Type 5
17 to 32 3 1 1 Type 6
97 to 128 1 to 16 3 0 1 Type 7
17 to 32 3 1 1 Type 8
129 to 160 1 to 16 4 0 1 Type 9
17 to 32 4 1 2 Type 10
161 to 192 1 to 16 5 0 2 Type 11
17 to 32 6 1 2 Type 12
193 to 224 1 to 16 6 0 2 Type 13
17 to 32 6 1 2 Type 14
225 to 256 1 to 16 7 0 2 Type 15
17 to 32 7 1 3 Type 16

17
■Switch Settings for Video Input Main Board
With the switch settings of main boards, board numbers are given to all video input boards. To give the board number to each
board, rotate the Unit No. switch on the main board.
Notes:
• The board number setting must be different from each other.
• "8", "9", and "A" to "F" are reserved settings. They cannot be set for board numbers.
RESET
No.
MODE
Board number switch
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Board number Switch setting
10
21
32
43
54
65
87
76
Important:
• The software versions of Video Output Board 1 and 2
must be the same.
If the software version of each board is different,
upgrade the lower version to the higher one. (Refer to
p. 42 or p. 55 for how to check the software version.)
• Refer to the dealer for the version-up procedure. (Surely
follow the instructions and notes.)

18
■Switch Settings for Video Output Main Board
When mounting an additional video input board, up to 32 monitors can be connected to the unit.
Front view of video output main board
To identify Video Output Board 1 from Video Output Board 2, set the MODE switches (SW4004) and sliding switches (SW1,
SW2, SW3, SW4, and SW4006) as follows.
Note: If the unit has only one Video Output Board, be sure to apply switch settings of Video Output Board 1. When the switch
settings are incorrect, the unit may not work properly.
HOST
FUNC
SW4006
1 2
SW1, SW2, SW3, SW4
RESET
TEST
MODE
MODE switches
OFF
12345 6 7 8
SW1, SW2, SW3, SW4
SW4006
MODE switches (SW4004)
OFF
12345678
OFF
12345678
1
HOST
2
FUNC
Video Output Board 1
(Monitor 1 to 16)
Video Output Board 2
(Monitor 17 to 32)

19
■Mounting Video Input and Output Boards
To use additional video input or output boards, mount these boards into the expansion slots of the unit after checking the
board composition and performing switch settings (refer to pp. 16 to 18). The following is the figures describing recommended
board composition.
Notes:
• Refer to p. 20 for how to mount these boards.
• Video Output Board 1 and 2 must be mounted into the same unit.
• Refer to p. 26 for how to connect card cages.
Type 1
Not used
Video Input Board 1
Video Output Board 1
Type 2
Video Input Board 1
Video Output Board 2
Video Output Board 1
Type 3
Video Input Board 2
Video Input Board 1
Video Output Board 1
Type 4
Not used
Not used
Video Input Board 2
Video Input Board 1
Video Output Board 2
Video Output Board 1
Type 5 Type 6 Type 7 Type 8
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 2
Video Output Board 1
Not used
Not used
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 1
Not used
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 2
Video Output Board 1
Not used
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 1
Type 9 Type 10 Type 11 Type 12
Not used
Video Input Board 6
Video Input Board 5
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 5
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 1
Not used
Not used
Video Input Board 5
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 5
Video Input Board 4
Video Input Board 3
Video Input Board 1
Video Output Board 2
Video Output Board 1
Video Input Board 1
Video Output Board 2
Video Output Board 1
Video Input Board 2
Video Input Board 1
Video Output Board 1
Not used
Not used
Video Input Board 6
Type 13 Type 14 Type 15 Type 16
Not used
Not used
Video Input Board 8
Video Input Board 7
Video Input Board 6
Video Input Board 5
Video Input Board 5
Video Input Board 6
Video Input Board 7
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 6
Video Input Board 7
Video Input Board 8
Video Input Board 5
Video Input Board 4
Video Input Board 3
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 2
Video Output Board 1
Video Input Board 1
Video Output Board 2
Video Output Board 1
Not used
Video Input Board 7
Video Input Board 6
Video Input Board 5
Video Input Board 4
Video Input Board 3
Video Input Board 2
Video Input Board 1
Video Output Board 1
Video Input Board 2
Video Input Board 1
Video Output Board 1

20
■Board Mounting Procedure
The following example is the procedure to mount a network
board into the expansion slot of the unit.
Note: Before the procedure, power off the unit.
1. Remove the expansion slot panel from the rear side.
2. Mount the rear boards into the expansion slot, and fix
these boards with screws supplied to the rear boards.
Notes:
• The board name (IN X-1, OUT X-1, etc.) is marked at
the lower right corner of each board mounting angle.
When mounting the rear boards, match the board
names with the markings at board mounting angles.
• To mount a set of video output board into the expansion
slot, dismount the IN B-3 board, and then mount the
OUT X-3.
3. Remove the front panel by loosening the screws.
4. Remove the blank panel from the front side.
5. Mount the main board by hooking the board stoppers
on the board stopper angles at the front side, by push-
ing down the board stoppers, and by fixing the screws.
Notes:
• Remove 3 screws surely at the arrow marking when dis-
mounting.
• When mounting, match the main board surely with the
rear board.
• When mounting, insert the main board surely into slits.
• Do not hit the boards against the chassis of the unit.
SIGNAL GND
SIGNAL GND
TERM.ON
ON
MODE
TERM.OFF
MODE
DATA4
HDR4/TMNL8
HDR2/TMNL4
DATA3
HDR3/TMNL7
HDR1/TMNL3
DATA2
TMNL6
TMNL2
DATA1
TMNL5
TMNL1/PSDATA
VideoOutputBoard 2
VideoOutput Board 1
Board stopper angle
Board stopper
•Mount the main board into the slot.
•Fix the board with the screws (x3).
•Attach the fixing brackets (x2) with the screws (x4).
Fixing brackets (x2)
Screws (x4)
Hook the board stoppers
on the board stopper angles, and
push down the board stoppers.
Matrix Switcher WJ-SX
650
OPERATE
SIGNAL GND
SIGNAL GND
TERM.ON
ON
MODE
TERM.OFF
MODE
DATA4
HDR4/TMNL8
HDR2/TMNL4
DATA3
HDR3/TMNL7
HDR1/TMNL3
DATA2
TMNL6
TMNL2
DATA1
TMNL5
TMNL1/PSDATA
VideoOutputBoard 2
VideoOutputBoard 1
IN X-2 board
IN X-1 board
Blank panel