Panasonic TH-50PHW7BX User manual

Power Source: AC120V 50/60Hz (UY version)
AC220-240V 50/60Hz
(Except UY version model)
Power Consumption: 480 W (UY version)
435 W (Except UY)
Save off 0.8 W, Save on 0.5 W (stand-b
y
condition)
(UY version)
Save off 1.0 W, Save on 0.7 W (stand-by
condition)
(Except UY version model)
0.1 W (Power off condition)
(UY version model)
0.3 W (Power off condition)
(Except UY version model)
Plasma Displa
y
panel: Drive method AC type
16:9 aspect ratio
Contrast Ratio 3000:1
Screen size: 1,106 mm (W) × 622 mm (H)
1,269 mm (diagonal)
No. of pixels
1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
Operating condition:
Temperature 32 °F - 104 °F (0 °C - 40 °C)
Humidit
y
20 % - 80 %
©2004 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TH-50PHW7BX
TH-50PHW7EX
TH-50PHD7EK
TH-50PHD7ES
TH-50PHD7BK
TH-50PHD7BS
TH-50PHD7UY
GPH7D2 Chassis
Applicable signals
Colour System NTSC, PAL, PAL60, SECAM, Modified NTSC
Scannin
g
format 525 (480)
/
60i 60p, 625 (575)
/
50i 50p,
750 (720) / 60p 50p, 1125 (1080) / 60i 50i
24p 25p 30p 24sF ... SMPTE274M, 1250
(1080) / 50i
PC si
g
nals XGA displa
y
VGA, SVGA, XGA,
SXGA, UXGA ... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals:
AV (UY version)
Video in/out 1.0 Vp-p (75-ohm)
S-VIDEO IN
(MINI DIN 4PIN)
Y: 1 Vp-p (75-ohm), C: 0.286 Vp-p
(75-ohm)
AUDIO IN
(RCA PIN JACK × 2)
0.5 Vrms (hi
g
h impedance)
COMPONENT/RGB
(UY version)
Y/G 1.0 Vp-p
/
composite (75-ohm)
0.7 Vp-p
/
non-composite (75-ohm)
PB
/
B0.7 Vp-p (75-ohm)
PR
/
R0.7 Vp-p (75-ohm)
HD 1.0 - 5.0 Vp-p (hi
g
h impedance)
VD 1.0 - 5.0 Vp-p (hi
g
h impedance)
High Definition Plasma Display
Specifications
SORDER NO. ITD0410044C0
D10 Canada: B07
www.ma163.net 树叶整理

AUDIO IN
(RCA PIN JACK×2)
0.5 Vrms (hi
g
h impedance)
PC
(HIGH-DENSITY
D-SUB15PIN)
R,G,B
/
0.7 Vp-p (75-ohm)
HD, VD/1.0 - 5.0 Vp-p (hi
g
h
impedance)
AUDIO IN (M3 JACK) 0.5Vrms (hi
g
h impedance)
1 Applicable signals 4
2 Safety Precautions 5
2.1. General Guidelines 5
3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 6
4 About lead free solder (PbF) 7
5 PCB Structure sheet of GPH7D2 chassis 8
6 Service Hint 9
7 Location of Lead Wiring 10
8 P.C.Board and Plasma panel replacement 11
8.1. Removal of the back cover 11
8.2. Removal of the Slot block 11
8.3. Removal of the J-Board 11
8.4. Removal of the HX-Board 11
8.5. Removal of the P-Board 11
8.6. Removal of the Z-Board 12
8.7. Removal of the D-Board 12
8.8. Removal of the PF-Board 12
8.9. Removal of the H3-Board 13
8.10. Removal of the SU-Board 13
8.11. Removal of the SD-Board 13
8.12. Removal of the SC-Board 13
8.13. Removal of the SS-Board 14
8.14. Removal of the SS2-Board 14
8.15. Removal of the SS3-Board 14
8.16. Removal of the fan 14
8.17. Removal of the C1-Board 15
8.18. Removal of the C2-Board 15
8.19. Removal of the C3-Board 15
8.20. Removal of stand brackets 15
8.21. Removal of the C4-Board 15
8.22. Removal of the C5-Board 16
8.23. Removal of the C6-Board 16
8.24. Removal of the Front frame (glass) 16
8.25. Replacement of the plasma panel 16
9 Adjustment Procedure 17
9.1. Driver Set-up 17
SERI
A
L
EXTERNAL CONTROL
TERMINAL (D-SUB9PIN)
RS-232C COMPATIBLE
SPE
A
KERS (External
speakers) (6W
WW
W)
16W [8W+8W] (10% THD)
Dimensions (W×H×D): 1,210 mm ×724 mm 95 mm
Weight (Mass) approx. 42.5 k
g
net (main unit only)
approx. 47.1 kg net (with speakers)
9.2. Initialization Pulse Adjust 18
9.3. P.C.B. (Printed Circuit Board) exchange 19
9.4. Adjustment Volume Location 19
9.5. Test Point Location 19
10 Service mode 20
10.1. CAT (computer Aided Test) mode 20
10.2. IIC mode structure (following items value is sample data.)
22
11 Alignment 23
11.1. PC/RGB panel white balance 23
11.2. HD/ 525i /525p /625i /625p panel white balance 26
12 Trouble shooting guide 28
12.1. Self Check 28
12.2. No Power 28
12.3. No Picture 30
12.4. Local screen failure 30
13 Option Setting 31
13.1. How to access and setting 31
13.2. Contents of Open Menu 32
14 Circuit Board Layout 33
14.1. PF-Board 33
14.2. P-Board 34
14.3. HA-Board 37
14.4. HB-Board 38
14.5. HX-Board 39
14.6. J-Board 40
14.7. D-Board 42
14.8. C1-Board 44
14.9. C2-Board 45
14.10. C3-Board 46
14.11. C4-Board 47
14.12. C5-Board 48
14.13. C6-Board 49
14.14. SC-Board 50
14.15. SU-Board 53
14.16. SD-Board 54
14.17. SS-Board 55
CONTENTS
Page Page
2
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

14.18. Z-Board 57
14.19. H3, S1 and V1-Board 58
15 Schematic Diagrams 59
15.1. Schematic Diagram Notes 59
15.2. Main Block Diagram 60
15.3. PF and P-Board Block Diagram 61
15.4. PF-Board Schematic Diagram 62
15.5. P-Board (1 of 6) Schematic Diagram 63
15.6. P-Board (2 of 6) Schematic Diagram 64
15.7. P-Board (3 of 6) Schematic Diagram 65
15.8. P-Board (4 of 6) Schematic Diagram 66
15.9. P-Board (5 of 6) Schematic Diagram 67
15.10. P-Board (6 of 6) Schematic Diagram 68
15.11. HA-Board Block Diagram and Schematic Diagram 69
15.12. HB-Board Block Diagram 70
15.13. HB-Board (1 of 2) Schematic Diagram 71
15.14. HB-Board (2 of 2) Schematic Diagram 72
15.15. HX-Board Block Diagram and Schematic Diagram 73
15.16. J-Board Block Diagram 74
15.17. J-Board (1 of 4) Schematic Diagram 75
15.18. J-Board (2 of 4) Schematic Diagram 76
15.19. J-Board (3 of 4) Schematic Diagram 77
15.20. J-Board (4 of 4) Schematic Diagram 78
15.21. D-Board (1 of 2) Block Diagram 79
15.22. D-Board (2 of 2) Block Diagram 80
15.23. D-Board (1 of 12) Schematic Diagram 81
15.24. D-Board (2 of 12) Schematic Diagram 82
15.25. D-Board (3 of 12) Schematic Diagram 83
15.26. D-Board (4 of 12) Schematic Diagram 84
15.27. D-Board (5 of 12) Schematic Diagram 85
15.28. D-Board (6 of 12) Schematic Diagram 86
15.29. D-Board (7 of 12) Schematic Diagram 87
15.30. D-Board (8 of 12) Schematic Diagram 88
15.31. D-Board (9 of 12) Schematic Diagram 89
15.32. D-Board (10 of 12) Schematic Diagram 90
15.33. D-Board (11 of 12) Schematic Diagram 91
15.34. D-Board (12 of 12) Schematic Diagram 92
15.35. C1, C2, C5 and C6-Board Block Diagram 93
15.36. C3 and C4-Board Block Diagram 94
15.37. C1-Board (1 of 2) Schematic Diagram 95
15.38. C1-Board (2 of 2) Schematic Diagram 96
15.39. C2-Board (1 of 2) Schematic Diagram 97
15.40. C2-Board (2 of 2) Schematic Diagram 98
15.41. C3-Board (1 of 2) Schematic Diagram 99
15.42. C3-Board (2 of 2) Schematic Diagram 100
15.43. C4-Board (1 of 2) and V1-Board Schematic Diagram 101
15.44. C4-Board (2 of 2) Schematic Diagram 102
15.45. C5-Board (1 of 2) Schematic Diagram 103
15.46. C5-Board (2 of 2) Schematic Diagram 104
15.47. C6-Board (1 of 2) Schematic Diagram 105
15.48. C6-Board (2 of 2) Schematic Diagram 106
15.49. SC-Board Block Diagram 107
15.50. SC-Board (1 of 3) Schematic Diagram 108
15.51. SC-Board (2 of 3) Schematic Diagram 109
15.52. SC-Board (3 of 3) Schematic Diagram 110
15.53. SU-Board Block Diagram 111
15.54. SU-Board (1 of 2) Schematic Diagram 112
15.55. SU-Board (2 of 2) Schematic Diagram 113
15.56. SD-Board Block Diagram 114
15.57. SD-Board (1 of 2) Schematic Diagram 115
15.58. SD-Board (2 of 2) Schematic Diagram 116
15.59. SS, SS2, SS3 and S1-Board Block Diagram 117
15.60. SS-Board (1 of 2) and S1-Board Schematic Diagram 118
15.61. SS-Board (2 of 2), SS2 and SS3-Board Schematic
Diagram 119
15.62. Z-Board and H3-Board Block Diagram 120
15.63. Z-Board (1 of 2) and H3-Board Schematic Diagram 121
15.64. Z-Board (2 of 2) Schematic Diagram 122
16 Parts Location 123
17 Packing Exploded Views 124
17.1. Packing Exploded Views (1) 124
17.2. Packing Exploded Views (2) 125
17.3. Packing Exploded Views (3) 126
18 Mechanical Replacement Parts List 127
19 Replacement Parts List 129
19.1. Replacement Parts List Notes 129
19.2. Electrical Replacement List 130
3
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

1 Applicable signals
4
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

2.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1MWand 5.2MW.
When the exposed metal does not have a return path to
the chassis, the reading must be .
Figure 1
2.1.2. Leakage Current Hot Check (See
Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 1.5kW, 10 watts resistor, in parallel with a 0.15µF
capacitors, between each exposed metallic part on the set
and a good earth ground such as a water pipe, as shown in
Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
2 Safety Precautions
2.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
5
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
6
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

4 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB.
Caution
· Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
· Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
· After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
7
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

5 PCB Structure sheet of GPH7D2 chassis
Board Name Function Remarks
DDigital Signal Processor 1
JSlot Interface & SYNC processor 1
ZAudio out, DC-DC converter
SS Sustain Out 1
SC Scan out 1
SU Sustain connection (Upper) 1
SD Sustain connection (Lower) 1
C1 Data Drive (Upper Right)
C2 Data Drive (Upper Center)
C3 Data Drive (Lower Left)
C4 Data Drive (Lower Left)
C5 Data Drive (Lower Center)
C6 Data Drive (Lower Right)
H3 Speaker terminal
S1 Power switch
SS2 Sustain connection (Upper)
SS3 Sustain connection (Lower)
V1 Front SW. & Remote receiver
PF Line filter
PPower supply 1
HX PC_type_Input terminal
HB BNC Composite Video 2, 3
HA BNC Component Video 2, 3
Remarks
1. Recommend PCB´s for initial service for GPH7D2 chassis.
2. For System model except BX, EX version
3. For Consumer model except BX, EX version
8
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

6 Service Hint
Service position for HB-Board, HA-Board and TY-42TM6
Note:
Extension cable kit for Slot Board is supplied as service fixtures and tools.
(Part No. TZSC0704)
9
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

7 Location of Lead Wiring
10
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

Prior to the replacement, place the unit on the pedestal
stand remove the front frame.
8.1. Removal of the back cover
a. Unscrew the screws (×19 ,×6 , ×4) and remove the
back cover.
8.2. Removal of the Slot block
a. Disconnect the couplers (J1, J3, J5, J6, J8, J10).
b. Unscrew the screws (×4) and remove the slot block.
8.3. Removal of the J-Board
a. Unscrew the screws (×7) and remote the J-Board.
8.4. Removal of the HX-Board
a. Unscrew the screws (×6) and remove the slot case.
b. Unscrew the screws (×4).
c. Unscrew the screws (×2) and remove the HX-Board.
8.5. Removal of the P-Board
a. Disconnect the couplers (P2, P5, P9, P10, P11, P12, P23,
P25, P27).
b. Unscrew the screws (×8) and remove the P-Board.
8 P.C.Board and Plasma panel replacement
11
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

8.6. Removal of the Z-Board
a. Disconnect the couplers (Z5, Z6, Z7, Z8, Z30, Z31).
b. Unscrew the screws (×4) and remove the Z-Board with
theZ-BoardBracket.
c. Unscrew the screws (×4) and remove the Z-Board.
8.7. Removal of the D-Board
a. Disconnect the couplers (D1, D3, D5, D10, D25, D27) and
the flexible cables (D31, D32, D33, D34).
b. Unscrew the screws (×6) and remove the D-Board.
8.8. Removal of the PF-Board
a. Remove the PF shield case cover and disconnect the
coupler (PF1).
b. Unscrew the screws (×2) and remove the AC inlet.
c. Disconnect the couplers (PF9, PF10).
d. Unscrew the screws (×4), and remove the PF-Board.
12
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

8.9. Removal of the H3-Board
a. Unscrew the screws (×2), and remove the H3-Board
with the Bracket.
b. Unscrew the screws (×4), and remove the H3-Board.
8.10. Removal of the SU-Board
a. Unscrew the screws (×3).
b. Slide the SU-Board to the left and disconnect from the
couplers (SC41) on the SC-Board.
c. Disconnect the coupler (SU45).
d. Disconnect the flexible cables (SU1, SU2, SU3, SU4)
connected to the SU-Board, and remove the SU-Board.
8.11. Removal of the SD-Board
a. Unscrew the screws (×3).
b. Slide the SD-Board to the left and disconnect from the
couplers (SC42) on the SC-Board.
c. Disconnect the coupler (SD46).
d. Disconnect the flexible cables (SD1, SD2, SD3, SD4)
connected to the SD-Board, and remove the SD-Board.
8.12. Removal of the SC-Board
a. Disconnect the couplers (SC2, SC12, SC13, SC20, SC23,
SC45, SC46, SC62).
b. Unscrew the screws (×9) and remove the SC-Board.
13
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

8.13. Removal of the SS-Board
a. Disconnect the couplers (SS11, SS12, SS32, SS34, SS35,
SS42).
b. Disconnect the coupler (SS21) on SS2-Board.
c. Disconnect the coupler (SS31) on SS3-Board.
d. Disconnect the flexible cables (SS51, SS52, SS53, SS54,
SS55, SS56).
e. Unscrew the screws (×7), and remove the SS-Board.
8.14. Removal of the SS2-Board
a. Disconnect the couplers (SS21).
b. Disconnect the flexible cable (SS41).
b. Unscrew the screws (×2) and remove the SS2-Board.
8.15. Removal of the SS3-Board
a. Disconnect the couplers (SS31).
b. Disconnect the flexible cable (SS48).
b. Unscrew the screws (×2) and remove the SS3-Board.
8.16. Removal of the fan
a. Disconnect the fan cable connector.
b. Unscrew the screws (×3) and remove the fan.
14
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

8.17. Removal of the C1-Board
a. Disconnect the flexible cables (CA1, CA2, CA3, CA4, C10,
C11).
b. Disconnect the couplers (C12, C13) release the SC45-SU45
cable from the clamper on the C1-Board.
c. Unscrew the screws (×5) and remove the C1-Board.
8.18. Removal of the C2-Board
a. Disconnect the flexible cables (CA5, CA6, CA7, C20, C21,
C22, C23, C24, C25).
b. Unscrew the screws (×5) and remove the C2-Board.
8.19. Removal of the C3-Board
a. Disconnect the flexible cables (CA8, CA9, CA10, CA11, C31,
C33).
b. Disconnect the couplers (C32, C35).
c. Unscrew the screws (×5) and remove the C3-Board.
8.20. Removal of stand brackets
a. Lay on a table (covered), with the plasma panel surface
facing downward.
Spread a soft cloth for protection, to prevent panel surface from
scratching.
b. Unscrew the stand bracket (left, right) fastening screws (×4
each) and remove the stand brackets (left, right).
8.21. Removal of the C4-Board
a. Disconnect the cables (CB8, CB9, CB10, CB11, C41, C43).
b. Disconnect the couplers (C42, C44) and release the speaker
cables from the clampers (×2) on the C4-Board.
c. Unscrew the screws (×5), and remove the C4-Board.
15
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

8.22. Removal of the C5-Board
a. Disconnect the flexible cables (CB5, CB6, CB7, C50, C51,
C52, C53, C54, C55).
b. Release the speaker cable from the clampers (×3) on the
C5-Board.
c. Unscrew the screws (×5) and remove the C5-Board.
8.23. Removal of the C6-Board
a. Disconnect the flexible cables (CB1, CB2, CB3,CB4,
C60,C61).
b. Disconnect the coupler (C62) and release the speaker
cables from the clampers (×4) on the C1-Board.
c. Unscrew the screws (×5), and remove the C1-Board.
8.24. Removal of the Front frame
(glass)
a. Remove the screws (×2) fasten on the panel and remove the
front panel.
b. Release all cables from the clamper on the bracket of the
front frame.
c. For leaving the plasma panel from the front frame, pull the
bottom of the front frame to forward, lift, and remove.
8.25. Replacement of the plasma
panel
a. Place the new plasma panel (finished) on the flat surface of
the table (covered by a soft cloth), with the plasma panel
surface facing downward.
b. Fit the stand brackets (left, right.) fast 4 screws each on the
new plasma panel.
c. Place the plasma panel section on the servicing stand.
d. Attach the front frame each P.C.Board and so on, to the new
plasma panel.
* When fitting the front frame, be careful not to allow any
debris, dust or handling residues to remain between the
front glass and plasma panel.
16
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

9.1. Driver Set-up
9.1.1. Item / Preparation
1. Input an APL 100 % white signal.
2. Set the picture controls: -
Picture mode: Normal
White balance: Cool
Aspect: 16:9
9.1.2. Adjustments
Adjust driver section voltages referring the panel data on the
panel data label.
Name Test Point Voltage Volume Remarks
Vsus TPVSUS 173V ± 2V R641 (P)
Ve TPVE 150V ± 1V VR6070 (SS)
Vda TPVDA 75V ± 1V R665 (P)
Vad TPVAD -85V ± 1V VR6477 (SC)
Vscn TPVSCN Vad+ 120V ± 4V ---
Vset TPVSET 220V ± 7V ---
PFC C448 (+)(-) 395V ± 0.5V R443 (P)
Vdat C560 (+)(-) 77V ± 0.1V R661 (P) load
current :
0.4A
Vsus TPVsus 163V ± 1V R608 (P) load
current :
2.0A
*See the Panel label.
9 Adjustment Procedure
17
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

9.2. Initialization Pulse Adjust
1. Input a Cross hatch signal.
2. Set the picture controls: -
Picture mode: Normal
White balance: Cool
Adjust the indicated test point for the specified wave form.
Test point Volume Level
T1 TPSC1 (SC) --- 20 ± 15µ Sec
T2 TPSS1 (SS) VR6557 (SC) 155 ± 10µ Sec
18
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

9.3. P.C.B. (Printed Circuit Board) exchange
9.3.1. Caution
1. To remove P.C.B. , wait 1 minute after power was off for discharge from electrolysis capacitors.
9.3.2. Quick adjustment after P.C.B. exchange
P.C.B. Name Test Point Voltage Volume Remarks
SS Board Vsus TPVSUS 173V ± 2V R641 (P)
Ve TPVE 150V ± 1V VR6070 (SS)
Vda TPVDA 75V ± 1V R665 (P)
SC Board Vad TPVAD -85V ± 1V VR6477 (SC)
Vscn TPVSCN Vad+ 120V ± 4V ---
Vset TPVSET 220V ± 7V ---
D, J Board White blance, Pedestal and Sub brightness for NTSC, PAL, HD, PC and 625i signals
*See the Panel label.
9.4. Adjustment Volume Location
9.5. Test Point Location
19
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理

10 Service mode
10.1. CAT (computer Aided Test) mode
To exit the CAT mode, access the ID mode and switch off the main power.
10.1.1. IIC mode
Select the IIC mode by Up/Down button on the remote control at the front page of CAT mode then press the Action button on
the remote control.
Subject and item are mentioned on page 14.
To exit the IIC mode, press the R button on the remote control.
20
TH-50PHW7BX / TH-50PHW7EX / TH-50PHD7EK / TH-50PHD7ES / TH-50PHD7BK / TH-50PHD7BS / TH-50PHD7UY
www.ma163.net 树叶整理