Panasonic TH-85PF12UK User manual

(The ratings and appearance are subject to change without notice.)
Temperature: 0°C to 40°C (Multi-system: 0°C to 35°C)
Environmental requirements Humidity: 20% to 80%
2,000,000:1Dynamic contrast
W 2,194 x H 1,480 x D 549 mmPackage size
Altitude: 0 to 2,800 m
Possible (without additional fans, with the power button side up.)Installation in portrait orientation
Audio output
Power supply
Display panel
Power consumption
Weight
Screen size
Dimensions (W x H x D)
Audio line-out
Compliant with the requirements of the destination country
Applied (AGLR finish)AR coating 40 WSlot power supply 0 to 2,800 mAltitude 6,144 shades of gray (equivalent)Gray scale levels
40000:1Contrast 1,920 x 1,080 pixels [1 pixel = 3 cells (RGB)]Number of pixels (H x V)
1,250W
1899/1062/2167 mm
PDP: 125 kg / With the package: Approx. 160 kg (*1)
W 2,015 x H 1,195 x D 99 mm
TH-85PF12U/K/W
*1: When a plastic pallet is used (The specifications have yet to be determined.)

zInstall the PDP in accordance with applicable laws and regulations of the
destination country/region.
zThe installation work must be carried out only by professionals.
zThe power supply for this PDP must meet the requirements of the destination
country. The rated power consumption is TBD.
It is recommended that the PDP use a dedicated power line.
zProvide adequate ventilation in the installation location so that the ambient
temperature will not exceed 40°C.
Make a clearance of 100 mm or more above and on both sides of the PDP and a
clearance of 150 mm or more behind the PDP.
zThe length of the power cord supplied with the PDP is 3 m.
zPosition of the center of gravity (Reference)
Horizontal and vertical center of gravity: The center of the set
Depth from the front to the center of gravity of the set
PDP alone: 33 mm
With the wall mount bracket: 51 mm
zEye bolt type
The size of the eye bolts on the PDP (two on the left and right sides and three on
the top) is M12-20 mm.

(Subject to change without notice due to improvements of the product specifications and/or design.)

(Subject to change without notice due to improvements of the product specifications and/or design.)

zStationary stand
The height of the PDP bottom side is 62.5 mm from the stationary stand. The PDP
can be set 50 mm higher to avoid interference between the PDP and the stand due
to the attachment of a touch panel or for other reasons. At the higher position, the
height of the PDP bottom side is 112.5 mm.
To prevent the stand from tipping over, fix the stand to the table by four points using
the supplied bands. In addition, fix the PDP to the wall by two points using strong
wires.
The stationary stand weighs 55 kg, and the total weight including the PDP is about
180 kg. Do not install the stand with the PDP in a location that cannot withstand the
load.
To prevent the PDP from coming off the mounting bracket, fix the PDP with M8 bolts.
zFloor stand
With the floor stand, the PDP height is adjustable to three different levels.
The height of the PDP bottom side is 1,000 mm/900 mm/800 mm from the floor
stand.
To prevent the stand from tipping over, fix the PDP by four points using adjusters. In
addition, fix the PDP to the wall by two points using strong wires.
To prevent the PDP from coming off the mounting bracket, fix the PDP with M8 bolts.

(Subject to change without notice due to improvements of the product specifications and/or design.)
A
B
2,1951,000
2,095900
1,995800
BA
zStand specifications (Model No.: TY-ST85PF12)
Dimensions: W 1,425 x H 1,413 to 1,606 x D 871 mm
Weight: 75.0 kg
Height adjustable to three levels

(Subject to change without notice due to improvements of the product specifications and/or design.)
zStand specifications (Model No.: TY-ST85P12)
Dimensions: W 1,401 x H 727 x D 443 mm
Weight: 55.0 kg

Fixing the PDP to a wall or post with wires
Fix the eye bolts on the rear of the PDP to a firm
wall or post with strong wires.
<Reference values>
* Each wire should be have a 4 mm or larger
diameter and withstand 0.8 tons or higher load.
* Each wire should be anchored to the wall with
M10 x 45 mm or larger anchor bolts. Two wires
should be anchored.
zThe installation work must meet applicable laws and regulations
of the destination country/region.
zFixing with wire
Wire
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
／
Wire
Stationary stand Floor stand

zWhen installing the PDP on a wall, change the stand
hook at the center to the upper stand hook position.
*1
Line mark
Line mark
“H” mark Wall
zWall mounting
The installation work must be carried out only by
professionals.
The marks denote the center of the PDP.
zWall mounting dimensional tolerances
Base bracket pitch (the part marked with *1):
1,230 ±0.6 mm
zSurface level difference tolerance: 1.3 mm
Pitch tolerance: Left-right: ±1.0 Top-bottom: ±1.0 (mm)
zStand specifications (Model No.: TY-WK85PV12)
Dimensions: W 1,420 x H 1,071 x D 150 mm
Weight: Approx. 25.0 kg