Panasonic BB-HCM381CE User manual

ORDERNO.KMS0505064CE
NetworkCamera
BB-HCM381CE/BB-HCM381E
(forEurope)
 2005PanasonicCommunicationsCo.,Ltd.Allrightsreserved.
Unauthorizedcopyinganddistributionisaviolationoflaw.
IMPORTANTINFORMATIONABOUTLEADFREE,(PbF),SOLDERING
Ifleadfreesolderwasusedinthemanufactureofthisproducttheprintedcircuitboardswillbemarked
1

PbF.
Standardleaded,(Pb),soldercanbeusedasusualonboardswithoutthePbFmark.
Whenthismarkdoesappearpleasereadandfollowthespecialinstructionsdescribedinthismanual
ontheuseofPbFandhowitmightbepermissibletousePbsolderduringserviceandrepairwork.
1.ABOUTLEADFREESOLDER(PbF:Pbfree)
Note:
Intheinformationbelow,Pb,thesymbolforleadintheperiodictableofelements,willrefertostandard
solderorsolderthatcontainslead.
WewillusePbFwhendiscussingtheleadfreesolderusedinourmanufacturingprocesswhichismade
fromTin,(Sn),Silver,(Ag),andCopper,(Cu).
Thismodel,andotherslikeit,manufacturedusingleadfreesolderwillhavePbFstampedonthePCB.
Forserviceandrepairworkwesuggestusingthesametypeofsolderalthough,withsomeprecautions,
standardPbsoldercanalsobeused.
Caution
-PbFsolderhasameltingpointthatis50°~70°F,(30°~40°C)higher
thanPbsolder.Pleaseuseasolderingironwithtemperaturecontrol
andadjustitto700°±20°F,(370°±10°C).Incaseofusinghigh
temperaturesolderingiron,pleasebecarefulnottoheattoolong.
-PbFsolderwilltendtosplashifitisheatedmuchhigherthanitsmelting
point,approximately1100°F,(600°C).
-IfyoumustusePbsolderonaPCBmanufacturedusingPbFsolder,
removeasmuchoftheoriginalPbFsolderaspossibleandbesurethat
anyremainingismeltedpriortoapplyingthePbsolder.
-WhenapplyingPbFsoldertodoublelayeredboards,pleasecheckthe
componentsideforexcesswhichmayflowontotheoppositeside(See
figure,below).
1.1.SUGGESTEDPbFSOLDER
ThereareseveraltypesofPbFsolderavailablecommercially.Whilethisproductismanufacturedusing
Tin,Silver,andCopper,
(Sn+Ag+Cu),youcanalsouseTinandCopper,(Sn+Cu),orTin,Zinc,andBismuth,(Sn+Zn+Bi).Please
checkthemanufac
turer’sspecificinstructionsforthemeltingpointsoftheirproductsandanyprecautionsforusingtheir
2

productwithother
materials.
Thefollowingleadfree(PbF)solderwiresizesarerecommendedforserviceofthisproduct:0.3mm,
0.6mmand1.0mm.
1.2.HOWTORECOGNIZETHATPbFREESOLDERISUSED
MainBoard
TiltBoard
3

LensBoard
4

VideoBoard
CCDBoard
5

I/OBoard
2.FORSERVICETECHNICIANS
ICsandLSIsarevulnerabletostaticelectricity.
Whenreplacing,thefollowingprecautionswillhelptopreventrecurringmalfunctions.
1.Covertheplasticpartswithaluminumfoil.
2.Groundthesolderingirons.
3.Useaconductivematonthework-table.
4.DonotgraspICorLSIpinswithbarefingers.
6

3.CAUTION
3.1.SAFETYPRECAUTIONS
1.Beforeservicing,unplugthepowercordtopreventanelectricalshock.
2.Whenreplacingparts,useonlymanufacturer’srecommended
componentsforsafety.
3.Checktheconditionofpowercord.Replaceifwearordamageis
evident.
4.Afterservicing,besuretorestoretheleaddress,insulationbarriers,
insulationpapers,shields,etc.
5.Beforereturningtheservicedequipmenttothecustomer,makethe
followinginsulationresistancetesttopreventashockhazard.
3.2.BATTERYCAUTION
Dangerofexplosionifthebatteryisreplacedincorrectly.Replaceonlywiththesameorequivalenttype
recommendedbythemanufacturer.Disposeofusedbatteriesaccordingtothemanufacturer’s
Instructions.
Thelithiumbatteryisacriticalcomponent(typeNo.BR-2032-1VC).Pleaseobservefortheproper
polarityantheexactlocationwhenreplacingitandsolderingthereplacementlithiumbatteryin.
3.3.TRADEMARKS
-Adobe,AcrobatandReaderareeitherregisteredtrademarksor
trademarksofAdobeSystemsIncorporatedintheUnitedStatesand/or
othercountries.
-EthernetiseitheraregisteredtrademarkoratrademarkofXerox
7

CorporationintheUnitedStatesand/orothercountries.
-Microsoft,WindowsandActiveXareeitherregisteredtrademarksor
trademarksofMicrosoftCorporationintheUnitedStatesand/orother
countries.
-PentiumisatrademarkorregisteredtrademarkofIntelCorporationor
itssubsidiariesintheUnitedStatesandothercountries.
-SDmarkisatrademarkoftheSDCardAssociation.
-ScreenshotsreprintedwithpermissionfromMicrosoftCorporation.
-Allothertrademarksidentifiedhereinarethepropertyoftheirrespective
owners.
3.4.INSULATIONRESISTANCETEST
1.UnplugtheACpowercordandshortthetwoprongsoftheplugwitha
jumperwire.
2.MeasuretheresistancevaluewithohmmeterbetweenthejumperedAC
plugandeachexposedmetalcabinetpart,suchasscrewthreads,etc.
Note:
Someexposedpartsmaybeisolatedfromthechassisbydesign.Thesewillreadinfinity.
3.Ifthemeasurementisoutsidethespecifiedlimits,thereisapossibility
ofshockhazard.Theequipmentshouldberepairedandrechecked
beforeitisreturnedtothecustomer.
8

3.5.POWERCAUTION
Thepowersocketwalloutletshouldbelocatednearthisequipmentandbeeasilyaccessible.
3.6.PRECAUTIONSFORUSERSINTHEUNITEDKINGDOM
FORYOURSAFETY,PLEASEREADTHEFOLLOWINGTEXTCAREFULLY.
Thisapplianceissuppliedwithamouldedthreepinmainsplugforyoursafetyandconvenience.A3
ampfuseisfittedinthisplug.Shouldthefuseneedtobereplaced,pleaseensurethatthereplacement
9

fusehasaratingof3ampsandthatitisapprovedbyASTAorBSItoBS1362.
CheckfortheASTAmark ortheBSImark onthebodyofthefuse.
Iftheplugcontainsaremovablefusecover,youmustensurethatitisrefittedwhenthefuseis
replaced.Ifyoulosethefusecover,theplugmustnotbeuseduntilareplacementcoverisobtained.A
replacementfusecovercanbepurchasedfromyourlocalPanasonicDealer.
IFTHEFITTEDMOULDEDPLUGISUNSUITABLEFORTHESOCKETOUTLETINYOURHOMETHEN
THEFUSESHOULDBEREMOVEDANDTHEPLUGCUTOFFANDDISPOSEDOFSAFELY.THEREISA
DANGEROFSEVEREELECTRICALSHOCKIFTHECUTOFFPLUGISINSERTEDINTOANY13AMP
SOCKET.
Ifanewplugistobefitted,pleaseobservethewiringcodeasshownbelow.Ifinanydoubt,please
consultaqualifiedelectrician.
IMPORTANT:THISAPPLIANCEMUSTBEEARTHED.
Howtoreplacethefuse:Thewiresinthismainsleadarecolouredinaccordancewiththefollowing
code:
Blue:Neutral
Brown:Live
Asthecoloursofthewireinthemainsleadofthisappliancemaynotcorrespondwiththecoloured
markingsidentifyingtheterminalsinyourplug,proceedasfollows.
ThewirewhichiscolouredBLUEmustbeconnectedtotheterminalintheplugwhichismarkedwith
theletterNorcolouredBLACK.
ThewirewhichiscolouredBROWNmustbeconnectedtotheterminalintheplugwhichismarkedwith
theletterLorcolouredRED.
Undernocircumstancesshouldeitherofthesewiresbeconnectedtotheearthterminalofthethreepin
plug,markedwiththeletterEortheEarthsymbol .
HowtoReplacetheFuse
1.Inserttheflatheadscrewdriverintothegrooveeitherendofthefuse
carrier.
2.Detachthefusecarrierandchangethefuse.
10