Panasonic BL-C30A - Wireless 802.11 b/g Network Camera Guide

How to Use This Documentation
The camera includes the following 3 manual types.
•Installation/Troubleshooting (This manual)
This manual has important information you will need to understand before
installing the camera and troubleshooting tips.
•Getting Started
Getting Started provides explanations for the initial configuration and
accessories included with the camera. TheGettingStarted helps you to easily
configure the camera.
•Operating Instructions (Included on the Setup CD-ROM)
Operating Instructions explains about operations, settings, features and the
cleaning method when using the camera.
Please read this manual before using and save this manual for future
reference.
Panasonic Network Camera Website: http://www.panasonic.com/netcam/ for
customers in the USA or Puerto Rico
Installation/Troubleshooting
Model No. BL-C30A
Network Camera

Installation/Troubleshooting
2
Abbreviations
•UPnP
TM is the abbreviation for Universal Plug and Play.
• "Network Camera" is called "Camera" in this Installation/Troubleshooting.
Trademarks
• Ethernet is either a registered trademark or a trademark of Xerox Corporation
in the United States and/or other countries.
• Windows and ActiveX are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
• Screen shots reprinted with permission from Microsoft Corporation.
• All other trademarks identified herein are the property of their respective
owners.

Installation/Troubleshooting
3
Table of Contents
1 Before Using..................................................................4
1.1 IMPORTANT SAFETY INSTRUCTIONS........................................4
1.1.1 FCC and Other Information....................................................................... 5
1.2 Camera Feature Locations.............................................................7
1.2.1 Front View.................................................................................................. 7
1.2.2 Bottom View .............................................................................................. 8
1.2.3 Rear View.................................................................................................. 8

Installation/Troubleshooting
4
1 Before Using
1.1 IMPORTANT SAFETY INSTRUCTIONS
When using thisunit, basic safety precautions should alwaysbe followed to reduce
the risk of fire, electric shock, or personal injury.
1. Read and understand all instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. After taking away the dust on the lens, wipe the lens with a cotton bud.
6. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including amplifiers) that produce heat.
7. Protect the AC adaptor cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the unit.
8. When you operate the camera, the power outlet should be near the camera
and easily accessible.
9. Do not touch the unit or the AC adaptor during lightning storms.
10.Unplug the unit when unused for long periods of time.
11.Refer all servicing to qualified service personnel. Servicing is required when
the unit hasbeen damaged in any way, such asthe AC adaptorcord or plug is
damaged, the unit does not operate normally, or has been dropped.
12.The camera is intended for indoor use only. Prolonged exposure to direct
sunlight or halogen light may damage CMOS sensor.
SAVE THESE INSTRUCTIONS
Network Camera Memo
Serial Number 
(Found on the rear side of the main unit) MAC Address

(Found on the rear side of the main unit)
Name and address of dealer
Date of purchase
For your future reference
Attach your purchase receipt here.

Installation/Troubleshooting
5
1.1.1 FCC and Other Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Some wireless Cameras operate at frequencies that may cause interference to
nearby TVs and VCRs. To minimize or prevent such interference, the base of the
wireless Camera should not be placed near or on top of a TV or VCR. If
interference is experienced, move the wireless Camera further away from the TV
or VCR. This will often reduce or eliminate interference. Operating near 2.4 GHz
electrical appliances may cause interference. Move away from the electrical
appliances.
Environment:
Do not install the camera where the temperature is less than 5 °C (+41 °F) or
greater than +40 °C (+104 °F). Allow 10 cm (4 inches) clearance around the unit
for proper ventilation. Avoid excessive smoke, dust, mechanical vibration, shock,
or direct sunlight.
Routine care:
Wipethe unit with a soft cloth. Donot use benzine,thinner, oranyabrasive powder.
When you leave the unit unused for a long period of time, unplug the AC adaptor
from the outlet.
If you have any problems:
Consult an authorized Panasonic Factory Service Center.

Installation/Troubleshooting
6
Caution
• To comply with FCC RF exposure requirements in uncontrolled environment:
•This equipment must be installed and operated in accordance with
provided instructions and a minimum 20 cm (8inches) spacing must be
provided between antenna and all person's body (excluding extremities of
hands, wrist and feet) during wireless modes of operation.
• This transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.
•Medical
Consult the manufacturer of any personal medical devices, such as
pacemakers, to determine if they are adequately shielded from external RF
(radio frequency) energy. (The unit operates in the frequency range of 2400
MHz to 2483.5 MHz, and the power output level is 0.1 watts.) Do not use the
unitin healthcarefacilities if any regulationsposted inthearea instruct younot
to do so. Hospitals or health care facilities may be using equipment that could
be sensitive to external RF (radio frequency) energy.
• Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this device.
No responsibility will be taken by our company with respect to consequences
resulting from the use, damage or both of the camera.

Installation/Troubleshooting
7
1.2 Camera Feature Locations
1.2.1 Front View
Privacy Button
To temporarily deactivate the camera, press the privacy button. Once pressed, the
button changes from green to red. The videowill be temporarily turned off, camera
features become unresponsive and the viewed image turns to a gray screen. To
return to normal operation, press the privacy button again. It should turn green
within a few seconds. To restore video, click [Refresh] on the web browser. Privacy
mode can also be controlled from mobile phones or PCs (see page or page of the
Operating Instructions in the Setup CD-ROM).
Indicator Display
Antenna
Pan/tilt Part
Do not apply pressure to the pan/tilt portion of the
camera. Any forced movement can damage the internal
mechanism.
Indicator/Privacy Button
Pyroelectric Infrared Sensor (see Getting Started)
Power 
on Normal Operation*1
*1The indicator turns orange if the camera is not connected to the LAN.
*2The indicator blinks orange if the camera is not connected to the LAN.
Updating Firmware
Getting IP address*2
Got IP address
Setting
Finished setting
Not on the LAN Orange Orange blinking
Orange blinking 
(The camera restarts after that.)
Pressing FACTORY 
DEFAULT RESET button
Orange blinking Turning off
UPnP Failure Orange blinking (About a 2-second interval)
On the LAN
Using 
DHCP
Automatic 
Setup
In Privacy Mode Red
Internal Failure Red blinking
Orange Green
Green
Green
Green 
Orange and green blinking
Green blinking
Green blinking

Installation/Troubleshooting
8
1.2.2 Bottom View
1.2.3 Rear View
Note
If the ceiling is made of wood, the camera can be installed on the ceiling. See
Panasonic Network Camera support website at http://panasonic.co.jp/pcc/
products/en/netwkcam/ for details.
Ethernet®
(LAN) port
DC IN jack
Tripod Mounting Hole
Used when installing the
camera on a tripod.
Stand Mounting Hole
Used when installing the camera onto a
wooden wall with a stand.
Used when installing 
the camera onto 
a wooden wall.

Installation/Troubleshooting
9
Memo

Installation/Troubleshooting
10