Panasonic K-EW114L03E User manual

HD IR Waterproof Fixed Network Camera
Quick Start Guide
Model No. K-EW114L03E
K-EW114L06E
K-EW114L08E
Version 1.0.0

i
Welcome
Thank you for purchasing our network camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated DC12V in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for anyproblems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for anyproblems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Thunder-proof device is recommended to be adopted to better prevent thunder.

ii
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
Important Safety Instructions
1

iii
.Table of Contents
1 Structure............................................................................................................................................1
1.1 Multiple-function Combination Cable...........................................................................1
1.2 Framework and Dimension ............................................................................................2
2 Device Installation...........................................................................................................................3
3 Quick Configuration Tool...............................................................................................................5
3.1 Overview.............................................................................................................................5
3.2 Operation............................................................................................................................5
4 Web Operation.................................................................................................................................7
4.1 Network Connection.........................................................................................................7
4.2 Login and Main Interface................................................................................................7

1
1 Structure
1.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function combination cable information. See
Figure 1-1.
Figure 1-1 Multiple-function combination cable
Please refer to the following sheet for detailed information.
No
Port Name
Function
Connection
Note
1.
LAN
Network port
Ethernet
Connect to standard Ethernet cable.
2
DC12V
Power input
port
Power input port. Input DC12V.

2
1.2 Framework and Dimension
Please refer to the following two figures for dimension information. The unit is mm. See Figure
1-2 and Figure 1-3.
Figure 1-2 Dimension illustration 1
Figure 1-3 Dimension illustration 2

3
2 Device Installation
Important
• Make sure that the installation area is strong enough to hold the product, such as a
concrete ceiling.
• Install the camera in the foundation area of the architecture or where sufficient strength
is assured.
• If a wall or ceiling board such as plasterboard is too weak to support the total weight, the
area shall be sufficiently reinforced.
Please see Figure 2-1 and Figure 2-2.
Step 1
Stick installation sticker to designated surface where you will install the device (wall or ceiling).
Step 2
Affix the installation template label (accessory) to the ceiling or wall, and use a pen to mark the
positions of the screws and cable mounting hole in the ceiling or wall. Remove the installation
template label and attach the camera with 3 screws (locally procured).
Step 3
Plug external wiring of the device properly.
Figure 2-1 Device installation 1
Step 4
Use Philip’s head screw (in accessories bag) to loosen adjusting screw.
Step 5
Adjust the device in all possible directions, and set its monitoring direction.
Step 6
Use Philip’s head screw to tighten the screws

4
Figure 2-2 Device installation 2

5
3 Quick Configuration Tool
3.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you
can use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
3.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 3-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 3-1 Search interface 1
Select one IP address and then right click mouse, you can see an interface is shown as in Figure
3-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 3-2 Search interface 2

6
If you want to modify the device IP address without logging in the device web interface, you can
go to the configuration tool main interface to set.
In the configuration tool search interface (Figure 3-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the
Login button to go to the login interface. See Figure 3-3.
In Figure 3-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in
Web Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.
Figure 3-3 Login prompt
After you logged in, the configuration tool main interface is shown as below. See Figure 3-4.
Figure 3-4 Main interface
For detailed information and operation instruction of the quick configuration tool, please
refer to the Quick Configuration Tool User’s Manual included in the resources CD.