Panasonic AW-UE150KP User manual

DVQP1812TA
W1118YM6032 -FJ
ENGLISH
Model No. AW‑UE150WP
Model No. AW‑UE150KP
Model No. AW‑UE150WE
Model No. AW‑UE150KE
Operating Instructions
4K Integrated Camera
Before operating this product, please read the instructions carefully and save this manual for future use.
Please carefully read the “Read this first!” (pages 2 to 5) of this Manual before use.
PJ EJ

Read this first! (For AW‑UE150WP, AW‑UE150KP)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
Do not pick up and move the unit while the tripod is attached.
The fitting may break under the weight of the tripod, which may
result in injury.
indicates safety information.
FCC NOTICE (USA)
Supplier’s Declaration of Conformity
Model Number: AW-UE150WP/AW-UE150KP
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
CAUTION:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
FCC Warning:
To assure continued FCC emission limit compliance, follow the attached installation instructions and the user must use only shielded interface
cables when connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this equipment could void
the user’s authority to operate this device.
NOTIFICATION (Canada)
CAN ICES-003 (A)/NMB-003(A)
indicates safety information.
2

Read this first! (For AW‑UE150WE, AW‑UE150KE)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws and drop-prevention wire mounting screw out of the
reach of infants and small children.
WARNING:
This equipment is compliant with Class A of CISPR 32.
In a residential environment this equipment may cause radio
interference.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
Do not pick up and move the unit while the tripod is attached.
The fitting may break under the weight of the tripod, which may
result in injury.
indicates safety information.
Turkey Only
AEEE Yönetmeliğine Uygundur.
AEEE Complies with Directive of Turkey.
2 3

EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Pre-requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to the
apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog audio signals.
• Other connecting cables (IEEE1394, USB)
Use double shielded cables, which provide quality performance for high-frequency applications, as connecting cables.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.
2. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by these standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strong
electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse
effects of the interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being
affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.
4
Read this first! (For AW‑UE150WE, AW‑UE150KE) (continued)

Disposal of Old Equipment
Only for European Union and countries with recycling systems
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not
be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your
national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health
and the environment. For more information about collection and recycling, please contact your local municipality, dealer or supplier.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Інформація для покупця
Виробник: Panasonic Connect Co., Ltd. Панасонік Коннект Ко., Лтд.
Адреса виробника: Fukuoka, Japan Фукуока Японія
Країна походження: Japan/China Японія/Китай
Імпортер: ТОВ "ПАНАСОНІК УКРАЇНА ЛТД"
Адреса імпортера: вул. Васильківська, буд. 30, м. Київ
03022, Україна
Примітки:
Термін служби виробу 7 років
Дата виготовлення може бути визначена за допомогою комбінації літер та цифр серійного номера, розташованого на продукті.
Приклад: X X XXXXXXX
Рік: остання цифра року (7 – 2017, 8 – 2018,…0 – 2020)
Місяць: А – Січень, В – Лютий… L – Грудень
Manufactured by:
Panasonic Connect Co., Ltd.
4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Importer:
Panasonic Connect Europe GmbH
Authorized Representative in EU:
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
Importer for UK:
Panasonic Connect UK,
a branch of Panasonic Connect Europe GmbH,
Maxis 2, Western Road, Bracknell, Berkshire, RG12 1RT
4 5
Read this first! (For AW‑UE150WE, AW‑UE150KE) (continued)

Read this first!
Note on grounding
• Ground the unit via the <SIGNAL GND> ground connector.
IR ID AUDIO IN
Ground connector
to ground
connector on wall
outlet, ground
bar, etc.
 Trademarks and registered trademarks
• Microsoft®, Windows®, Windows®7, Windows®10, Microsoft
Edge, Internet Explorer®, ActiveX®and DirectX®are either
registered trademarks or trademarks of Microsoft Corporation in
the United States and other countries.
• Apple, Mac, macOS, OS X, iPhone, iPad, and Safari are
registered trademarks of Apple Inc., in the United States and other
countries.
• Android™ and Chrome™ browser are trademarks of Google LLC.
• Intel®and Intel®Core™ are trademarks or registered trademarks
of Intel Corporation in the United States and other countries.
• Adobe®and Reader®are either registered trademarks or
trademarks of Adobe Systems Incorporated in the United States
and/or other countries.
• The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
• NDI®is a registered trademark of NewTek, Inc.
• Other names of companies and products contained in these
Operating Instructions may be trademarks or registered
trademarks of their respective owners.
 About copyright and licence
Distributing, copying, disassembling, reverse compiling, reverse
engineering, and also exporting in violation of export laws of the
software provided with this unit are expressly prohibited.
 Abbreviations
The following abbreviations are used in this manual.
• Microsoft®Windows®7 Professional SP1 32/64-bit is abbreviated
to “Windows 7”.
• Windows®Internet Explorer®11 32/64-bit is abbreviated to
“Internet Explorer”.
For the purposes of this manual, the model numbers of the units are
given as listed in the table below.
Model number of unit Model number given in
manual
AW-UE150WP
AW‑UE150
AW-UE150KP
AW-UE150WE
AW-UE150KE
AW-RP150G AW‑RP150
 Illustrations and screen displays featured
in the manual
• What is shown in the manual’s illustrations and screen displays
may differ from how it is actually appears.
• Functions which can be used by Windows Internet Explorer 11
only are indicated using the mark.
• The screenshots are used in accordance with the guidelines of
Microsoft Corporation.
6

Contents
Read this first! (For AW‑UE150WP, AW‑UE150KP) ............................ 2
Read this first! (For AW‑UE150WE, AW‑UE150KE) ............................ 3
Read this first! ...................................................................................... 6
Note on grounding ............................................................................... 6
Before use .............................................................................................. 8
Overview.............................................................................................. 8
Computer requirements ....................................................................... 8
Disclaimer of warranty ......................................................................... 9
Network security .................................................................................. 9
Features................................................................................................ 10
Accessories ......................................................................................... 11
Optional accessories .......................................................................... 11
Operating precautions ........................................................................ 12
Wireless remote control (optional accessory).................................. 14
Parts and their functions .................................................................... 15
Camera unit ....................................................................................... 15
Wireless remote control: AW-RM50G (optional accessory)............... 25
Setting the remote control IDs ........................................................... 27
Network settings.................................................................................. 28
Using Easy IP Setup Software to make settings for the unit.............. 28
Using EasyIP Setup Tool Plus to make settings for the unit.............. 28
Setting the initial account................................................................... 29
Installing the plug-in viewer software................................................. 29
Basic shooting operations ................................................................. 30
How to turn the power on and off ...................................................... 31
Turning the power on......................................................................... 31
Turning the power off......................................................................... 31
Selecting the units ............................................................................... 32
Selecting the shooting modes (scene files)...................................... 33
Types of shooting modes................................................................... 33
How to select the shooting mode....................................................... 33
Shooting ............................................................................................... 34
What to do when encountering problems in the basic shooting
operations ........................................................................................ 35
More advanced operations ................................................................. 36
Manual shooting .................................................................................. 37
Manually adjusting the focus.............................................................. 37
Manually adjusting the iris.................................................................. 37
Manually adjusting the shutter speed ................................................ 37
Manually adjusting the gain ............................................................... 37
Preset memories.................................................................................. 38
White balance adjustment .................................................................. 39
Automatic adjustment (AWB: AWB A or AWB B) .............................. 39
Auto tracking white adjustment (ATW)............................................... 40
3200K and 5600K presets ................................................................. 40
VAR.................................................................................................... 40
Black balance adjustment .................................................................. 41
Automatic adjustment ........................................................................ 41
Black level (master pedestal) adjustment ......................................... 42
Genlock adjustment ............................................................................ 43
Horizontal phase adjustment ............................................................. 43
Basic setup operations ....................................................................... 44
When performing the operations using the wireless remote
control ............................................................................................ 44
Camera menu items ............................................................................ 45
Setting the camera menu items ......................................................... 45
Top Menu screen............................................................................... 45
Camera screen .................................................................................. 46
Brightness 1/2 screen ........................................................................ 46
Brightness 2/2 screen ........................................................................ 47
Picture 1/8 screen.............................................................................. 48
Color TEMP. Setting screen .............................................................. 49
Picture 2/8 screen.............................................................................. 50
Picture 3/8 screen.............................................................................. 50
Picture 4/8 screen.............................................................................. 51
Picture 5/8 screen.............................................................................. 51
Picture 6/8 screen.............................................................................. 52
Picture 7/8 screen.............................................................................. 53
Picture 8/8 screen.............................................................................. 54
Matrix 1/5 screen ............................................................................... 54
Matrix 2/5 screen ............................................................................... 55
Matrix 3/5 screen ............................................................................... 55
Matrix 4/5 screen ............................................................................... 56
Matrix 5/5 screen ............................................................................... 56
Lens screen ....................................................................................... 57
System 1/2 screen ............................................................................. 57
System 2/2 screen ............................................................................. 58
Output 1/9 screen .............................................................................. 63
Output 2/9 screen .............................................................................. 64
Output 3/9 screen .............................................................................. 65
Output 4/9 screen .............................................................................. 66
Output 5/9 screen .............................................................................. 67
Output 6/9 screen .............................................................................. 67
Output 7/9 screen .............................................................................. 68
Output 8/9 screen .............................................................................. 68
Output 9/9 screen .............................................................................. 69
Pan/Tilt screen................................................................................... 71
Preset 1/2 screen............................................................................... 72
Preset 2/2 screen............................................................................... 73
Maintenance screen........................................................................... 74
Firmware Version 1/2 screen............................................................. 74
Firmware Version 2/2 screen............................................................. 75
IP Network screen.............................................................................. 75
Hour Meter screen ............................................................................. 76
HDMI Status screen........................................................................... 77
Error Status screen............................................................................ 78
Camera menu item table ..................................................................... 79
Displaying the web screen ................................................................. 86
Displaying the web screen using a personal computer...................... 86
Switching between the Live screen [Live] and Web setup screen
[Setup] ........................................................................................... 88
Logging into the Web screen ............................................................. 88
Web screen operations ....................................................................... 89
Live screen [Live]............................................................................... 89
Web screen configurations ................................................................ 94
Web setup screen [Setup].................................................................. 94
Setting status screen [Setting status]................................................. 95
Basic screen [Basic]........................................................................... 96
Image screen [Image/Audio]............................................................ 104
Collaboration capability [Linkage] .................................................... 127
User management screen [User mng.]............................................ 130
Network setup screen [Network]...................................................... 132
Maintenance screen [Maintenance]................................................. 148
Displaying the web screen using a personal computer equipped
with a touch panel ......................................................................... 152
Displaying the web screen using a mobile terminal ...................... 154
Camera control screen [Camera Control] ........................................ 154
Limiters............................................................................................... 156
Setting/releasing the limiters ........................................................... 157
Basic limiter operations.................................................................... 157
Setting the limiters ........................................................................... 157
Releasing the limiters....................................................................... 157
Resetting the limiters ....................................................................... 157
Safe mode .......................................................................................... 158
Concerning the safe mode............................................................... 158
Detection of equipment trouble........................................................ 158
Troubleshooting ................................................................................ 159
Specifications .................................................................................... 168
Index ...................................................................................................170
6 7

Before use
Overview
• This product is an all-in-one pan-tilt head remote camera that supports
4K/12G-SDI and is also compatible with 4K/60p format.
• Equipped with an optical 20x zoom lens and 4K-compatible MOS
sensor, it is possible to record high-quality images with a high degree
of realism with the horizontal resolution of 2000 lines.
With its high sensitivity and built-in image-shake correction and night-
mode functions, the unit can record in a wide range of environments.
• This product is compatible with NDI|HX version 2 technology of
NewTek, Inc.
• The unit supports transmission of video to NewTek NDI|HX compatible
software applications and hardware devices over a network.
• When a controller is connected, camera operations can be performed
smoothly via IP control or serial control.
• The unit features a night mode that exposes subjects to infrared rays,
making it possible to shoot even under low-light conditions.
• When the unit is connected to a personal computer via an IP network,
it can be operated via a web browser.
• With a variety of 4K interfaces, there are individual outputs for HD and
SDI, so the unit can be used flexibly in a wide range of situations as a
4K-compatible remote camera.
• Connection with a Panasonic camera controller is also possible via
Panasonic's proprietary serial communication format.
• The unit is available in white (AW-UE150WP/AW-UE150WE) or black
(AW-UE150KP/AW-UE150KE) to suit your intended application and
environment.
Computer requirements
CPU 7th Generation Intel®Core™ (Kaby Lake or later)
recommended
Memory For Windows:
4 GB or more
For Mac:
4 GB or more
Network function 100BASE-T/TX or 1000BASE-T,
RJ-45 connector
Image display Resolution: 1920 × 1080 pixels or more
Color generation: True Color 24-bit or more
Supported operating
systems and
web browsers
For Windows:
Microsoft®Windows®7, 10
Windows®Internet Explorer®11
64-bit/32-bit
Microsoft Edge
Google Chrome
For Mac:
macOS 10.13
Safari 11
macOS 10.12
Safari 11
OS X 10.11
Safari 11
Google Chrome
For iPhone, iPad:
iOS
Safari
For Android:
Android OS
Google Chrome
Other Adobe®Reader®
(for viewing the operating instructions available on
the website)
8

IMPORTANT
• Failure to provide the required personal computer
environment may slow down the delineation of the images on
the screen, make it impossible for the web browser to work
and cause other kinds of problems.
<NOTE>
• Depending on the software version of the unit, an update may be
necessary.
• For the latest information on compatible operating systems and web
browsers, visit the support desk at the following website.
https://pro-av.panasonic.net/
Disclaimer of warranty
IN NO EVENT SHALL Panasonic Connect Co., Ltd. BE LIABLE TO
ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT
OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
AANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,
DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR
EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
BPERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE
USER;
CUNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION
OF THE PRODUCT BY THE USER;
DINCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES
ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE
INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
EANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD PARTY;
FANY DEMANDS FOR COMPENSATION, CLAIMS, ETC.
OCCASIONED BY THE INFRINGEMENT OF PRIVACY BY
INDIVIDUALS OR ORGANIZATIONS WHOSE IMAGES WERE
SHOT BY THE USER BECAUSE THESE IMAGES (INCLUDING
THE RECORDINGS MADE) WERE MADE AVAILABLE BY THE
USER BECAUSE IN THE PUBLIC DOMAIN FOR SOME REASON
OR OTHER OR BECAUSE THE IMAGES ENDED UP BEING
USED FOR PURPOSES OTHER THAN THE ONE DESCRIBED
ABOVE;
GLOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
Network security
As the unit intended to be used while connected to a network, the
following security risks exist.
ALeakage or theft of information through the unit
BUnauthorized operation of the unit by persons with malicious intent
CInterference with or stoppage of the unit by persons with malicious
intent
It is your responsibility to take precautions, such as those described
below, to protect yourself against the above network security risks.
Panasonic does not accept any responsibility for damage of this type.
• Use the unit in a network secured by a firewall, etc.
• If the unit is connected to a network that includes personal computers,
make sure that the system is not infected by computer viruses or other
malicious programs (using a regularly updated antivirus program, anti-
spyware program, etc.).
• Protect your network against unauthorized access by restricting users
to those who log in with an authorized user name and password.
• After accessing the unit as an administrator, be sure to close all web
browsers.
• Change the administrator password periodically.
• To avoid passwords that can be guessed easily by third parties,
set a password of at least 8 characters in length, including at least
3 different types of characters, such as upper case, lower case,
numbers, and symbols.
• Restrict access to the unit by authenticating the users, for example,
to prevent setting information stored on the unit from leaking over the
network.
• Do not install the unit in locations where the unit, cables, and other
parts can be easily damaged or destroyed by persons with malicious
intent.
• Avoid connections that use public lines.
<NOTE>
Notes on user authentication
• User authentication on the unit can performed via digest authentication
or basic authentication. If basic authentication is used without the use
of a dedicated authentication device, password leaks may occur.
We recommend using digest authentication or host authentication.
Usage restrictions
• We recommend connecting the unit, controller, and any computers to
the same network segment.
Events based on settings inherent to the network devices, for example,
may occur in connections that include different segments, so be sure
to perform checks prior to operation.
8 9
Before use (continued)

 Multi‑format support
• You can switch between the following formats via the camera
menus or a web browser.
[4K format]
2160/59.94p, 2160/50p, 2160/29.97p*1 , 2160/25p*1 , 2160/24p*1 ,
2160/23.98p*1
[HD format]
1080/59.94p, 1080/50p, 1080/29.97p*1 , 1080/29.97PsF,
1080/25p*1 , 1080/25PsF, 1080/23.98p*2 , 1080/24p*1 ,
1080/23.98p*1 , 1080/23.98PsF, 1080/59.94i, 1080/50i,
720/59.94p, 720/50p
*1Native output
*2OVER 59.94i output (your monitor may recognize the signal as
59.94i).
 1‑type 4K MOS sensor and high‑performance
20x zoom lens featured
• A newly developed 1-type 4K MOS sensor and DSP (digital signal
processor) are incorporated. High-quality pictures are obtained by
video processing in many different kinds of ways.
• In addition to its optical 20x zoom lens, the unit comes with a 10x
digital zoom to achieve high-quality images that overflow with
ambiance.
• A dynamic range stretcher (DRS) function that compensates for
overexposure and loss of dark detail and a digital noise reduction
(DNR) function for minimizing image lag even in dark locations
and shooting scenes clearly are incorporated to reproduce clean
and clear images in a wide range of applications.
 Easy operation of unit enabled by its
integration with a high‑performance pan‑tilt
head unit
• Operations at the high speed of 60°/s
• Wide rotational angles with a panning range of ±175° and a tilting
range from –30° to 210°
• Quiet operation with noise levels of NC35
• Storage of up to 100 positions in the preset memory
(The number of preset memories that can be used varies from one
controller to another.)
 Built‑in night mode
• The unit supports infrared shooting.
By exposing subjects to infrared rays, shooting under ordinarily
difficult low-light conditions is possible.
(Image output will be in black and white.)
• The iris will be fixed at open.
 IP image output functions
• The unit is equipped with image compression and IP transmission
LSI capabilities. Output in 4K quality at up to 60 fps.
• Operation with IP control allows for a wide range of applications,
such as controlling the camera from remote locations.
 High degree of compatibility with Panasonic’s
currently available controllers, enabling a
flexible system to be put together
• A maximum of five units can be operated by serial control from
one of Panasonic’s currently available controllers (AW-RP150).
The unit can also be used together with the cameras and pan-tilt
head unit systems currently available from Panasonic Connect
Co., Ltd. so that an existing system can be used to advantage to
put together a system that is even more flexible.
<NOTE>
• It may be necessary to upgrade the version of the controllers
other than AW-RP150 in order to support the unit. For details on
upgrading, visit the support page on the following website.
https://pro-av.panasonic.net/
The maximum distances between the units and controller is
1000 meters (3280 ft). (when serial control is exercised)
Use of an external device or some other means must be
provided separately in order to extend the video signal
connections.
 Easy construction of systems thanks to
integrated design used for pan‑tilt head,
camera and lens
• By integrating the camera, lens and pan-tilt head into a single unit,
it is now easier to construct systems.

Use of easy‑to‑operate wireless remote control
(optional accessory) is possible
• A wireless remote control capable of operating up to four units can
be used.
It can easily be used to set the various functions or switch
between them while viewing the menu screens.
 Flexible camera layout enabled by simple
connection and installation
• This unit features excellent connectivity and installability thanks
to the IP control; a lightweight main unit, and the turn-lock
mechanism, which enables the user to install it on his or her own
(only when used indoors).
<NOTE>
• Bear in mind that this unit is designed to be used indoors only:
It cannot be used outdoors.
 While including a larger 4K lens and pan/
tilt mechanism, the unit still has the same
installation footprint as previous models.
• The unit maintains the compact installation footprint of previous
models.
 Easy connections and settings courtesy of IP
control
• Up to two hundred units can be operated by IP connection from a
Panasonic controller (AW-RP150).
(The maximum length of the LAN cables is 100 meters (328 ft).)
• Network connection with AW-RP150 requires setup of an initial
account. (→ page 29)
When an initial account is not set up, AW-RP150 can detect but
cannot control this unit.
 PoE++ *3eliminates need for camera power
configurations
• Configurations for camera's power supply are not necessary when
the unit is connected to a network device that supports the PoE++
standard (IEEE 802.3bt compliant)*4 .
Software authentication (LLDP) is also supported, but it may be
necessary to make settings on the network device (IEEE P802.3bt
compliant)*4.
<NOTE>
• If the external DC power supply and a PoE++ power supply are
connected simultaneously, the external DC power supply will have
priority. If the external DC power supply is disconnected while both
power supplies are connected, the unit will restart automatically,
and the image will be interrupted.
• Use a Category 5e cable or higher when using a PoE++ power
supply. The maximum length of the cable between the power
supply unit and the unit is 100 meters (328 ft). Using a cable that
is lower than Category 5e may result in reduced power supply
capabilities.
*3Power over Ethernet Plus Plus. Referred to as "PoE++" in this
manual.
*4For details on PoE++ power supply devices for which operation
has been verified, consult your local dealer.
Features
10

Accessories
Check that the following accessories are present and accounted for.
• After removing the product from its container, dispose of the power cable cap (if supplied) and packing materials in an appropriate manner.
Mount bracket for installation surface
(Hanging/Desktop) (1)
Main unit mounting screw (with flat washer, spring
washer)
M3×6 mm (1/4 inches) (1)
Drop‑prevention wire (1)
Drop‑prevention wire mounting screw (1)
(comes attached to the unit)
Bracket mounting screws (bind-head)
M4×10 mm (13/32 inches) (4)
Optional accessories
z Wireless remote control AW-RM50G (Size “AA” dry battery x 2, obtained separately)
z Direct ceiling mount bracket WV-Q105A
z Fiber module
<NOTE>
• For details on optional accessories, refer to the catalog or consult your local dealer.
10 11

 Do not use the unit in oily‑smoky or dusty
places.
Performance may be adversely affected if small particles or other
foreign objects get inside the product.
Take extra care in environments where a special effect such as
theatrical smoke is used.
 Shoot under the proper lighting conditions.
To produce pictures with eye-pleasing colors, shoot under the
proper lighting conditions.
The pictures may not appear with their proper colors when shooting
under fluorescent lights. Select the proper lighting as required.
 To ensure a stable performance in the long
term
Using the unit for prolonged periods in locations where the
temperature and humidity levels are high will cause its parts to
deteriorate, resulting in a reduction of its service life.
(Recommended temperature: Max. 35 °C (95 °F))
Ensure that a cooling unit or heating unit will not blow any air
directly toward the installation location.
 Do not point the camera at
strong lights.
When parts of the MOS sensor are
exposed to spotlights or other strong
lights, blooming (a phenomenon where
the edges of strong lights become
blurred) may occur.
Bright subject
Blooming
 What happens with high-brightness subjects
Flare may occur if an extremely bright light source is pointed at
the lens. In a case like this, change the angle or take some other
remedial action.
 When using the automatic functions
• In the [Scene] such as the camera menu, the initial settings on
some items has been set to auto, making it impossible for these
items to be operated manually. To operate them manually, switch
from the auto settings to the manual settings as required.
• When using the ATW (auto tracking white adjustment) function
under fluorescent lights, the white balance may vary.
• In some situations, it may be hard to focus at the auto setting. In
cases like this, select the manual setting, and focus manually.
 Zooming and focusing
When the focus is set manually, out-of-focusing may occur during
zooming.
After zooming, if necessary, either adjust the focus or set the focus
to auto.
When using the focus at the manual setting, proceed with zooming
after setting the focus position at the Tele end where the focusing
accuracy is higher. (However, if the distance from the unit to the
subject is less than 1.5 meters (4.92 ft), the subject may shift out of
focus at the Wide end.)
If zooming is performed to the Tele end after having adjusted the
focus at the Wide end, out-of-focusing may occur.
 Operation of the lens when the power is turned
on
When the unit’s power is turned on, the zoom, focus and iris are
adjusted automatically.
 The unit comes with the safe mode.
The safe mode is function designed to protect the unit from damage.
For details, refer to “Concerning the safe mode” (→ page 158).
 Operating temperature range
Avoid using the unit in cold locations where the temperature drops
below 0 °C (32 °F) or hot locations where the temperature rises
above 40 °C (104 °F) since these temperatures downgrade the
picture quality and adversely affect the internal parts.
 Concerning the MONI OUT signal
It is anticipated that MONI OUT is used in applications such as for
outputting images to be cropped from 4K to HD and for monitoring
images.
 Concerning the HDMI interface standard
This unit has been certified as HDMI-compatible, but on rare
occasions images may not be displayed depending on the HDMI
device which has been connected to the unit.
 Color bars
Color bars are used to adjust the color phase, and the widths and
positions of these bars may differ from other models.
 H.264/H.265 patent pool licensing
This product is licensed based on the AVC Patent Portfolio License,
and the license does not extend beyond uses by users, who engage
in the acts described below, for their own personal and non-profit
applications.
(i) Recording of image information in compliance with the AVC
standard (hereafter, “AVC videos”)
(ii) Playing of AVC videos recorded by consumers engaging
in personal activities or AVC videos acquired from licensed
providers
For details, visit MPEG LA, LLC website (http://www.mpegla.com).
 Concerning PoE++ power supply
The unit complies with the IEEE 802.3bt.
Use a compatible Ethernet hub and PoE++ injector to use a PoE++
power supply.
Software authentication (LLDP) complies with IEEE P802.3bt, but it
may be necessary to make settings on the network device.
For details on Ethernet hubs and PoE++ injectors for which
operations have been verified, consult your local dealer.
 Turn off the power before connecting or
disconnecting the cables.
This unit is not equipped with a power switch.
Turn off the DC 12 V power supply or PoE++ power supply device
before connecting or disconnecting cables.
 Handle the unit carefully.
Do not drop the unit or subject it to strong impact or vibration.
Failure to obey may cause the unit to malfunction.
 When the unit is not in use
Turn off the unit’s power when it is not in use.
When the unit is no longer to be used, make sure to remove the
camera and mount bracket rather than leaving them in place.
Operating precautions
12

 Do not touch the optical system parts.
The optical system parts are vital to the operation of the camera.
Under no circumstances must they be touched.
In the unlikely event that they have become dusty, remove the
dust by using a camera blower or by wiping them gently with a lens
cleaning paper.
 Do not point the camera directly at the sun or a
laser beam no matter whether it is turned on or
not.
Taking images of the sun, laser beams, or other brightly lit subjects
for prolonged periods of time may damage the CCD.
 Personal computer used
If the same image is displayed for a prolonged period on a personal
computer's monitor, the monitor may be damaged. Use of a screen
saver is recommended.
 Concerning the IP address setting
Do not run the Easy IP Setup Software on a multiple number of
personal computers for a single camera and set the IP address at
the same time.
Otherwise, you will be unable to complete the proper procedure and
set the IP address correctly.
 Do not allow foreign matter to make contact
with the rotating parts.
Failure to obey may cause the unit to malfunction.
 Do not get close to the moving parts of the
camera head.
Do not put your fingers or body close to the unit while it is in
operation. Doing so may result in injury or cause the unit to
malfunction.
Furthermore, if the unit hits a person or obstacle, during the panning
or tilting operation, the unit will enter into the safe mode.
For details, refer to the page 158.
 Keep the unit away from water.
Avoid all direct contact with water. Failure to obey may cause the
unit to malfunction.
 Maintenance
Turn off the unit’s power before proceeding with maintenance.
Failure to obey may result in injuries.
Wipe the surfaces using a soft dry cloth. Avoid all contact with
benzine, paint thinners and other volatile substances, and avoid
using these substances. Otherwise, the casing may become
discolored.
 Do not turn the camera head by hand.
Turning the camera head by hand may cause the unit to
malfunction.
 Use the unit in an environment with minimal
moisture and dust.
Avoid using the unit in an environment with high concentration of
moisture or dust since these conditions will damage the internal
parts.
 About the lens/pan-tilt head
If the lens, pan-tilt head, and other parts are not operated for a long
period of time, the viscosity of the grease applied inside them may
increase and operation may become no longer possible. Move the
lens and pan/tilt head regularly.
 About consumables
The following parts are consumables. Replace them using the
lifespans as a guide.
The lifespans may vary depending on the operating environment
and operating conditions. The lifespans are a guide for when the
unit is used at 35 °C (95 °F).
• Cooling fan: Approx. 15000 hours
Contact your dealer regarding replacements.
 Disposal of the unit
When the unit has reached the end of its service life and is to be
disposed of, ask a qualified contractor to dispose of the unit properly
in order to protect the environment.
 Information on software used with this product
This product includes GNU General Public License (GPL) and GNU Lesser General Public License (LGPL) licensed software, and the customer is
entitled to obtain, modify, or redistribute the source code for the software.
This product includes MIT Licensed software.
This product includes BSD Licensed software.
For details on obtaining the source codes, visit the following website.
https://panasonic.biz/cns/sav/
However, do not contact Panasonic for questions regarding obtained source codes.
12 13
Operating precautions (continued)

This unit can be operated by remote control using a wireless
remote control (model number: AW-RM50G) purchased separately.
Check out the following points before using the wireless remote
control.
z Point the wireless remote control at the unit’s wireless
remote control signal light‑sensing area (front panel or
back panel), and operate it within a range of 10 meters
(32.8 ft) from these areas.
z Refer to <Layout of wireless remote control signal
light-sensing areas> on the right.
z The signal sensing distance is reduced if the angle at
which the wireless remote control signals are sensed is
increased.
The light-sensing sensitivity is reduced to about one-half when the
wireless remote control is pointed at an angle of 40 degrees from
each position in front of a wireless remote control signal light-sensing
area (front panel or back panel).
If the remote control is operated from the behind the unit, it may be
either difficult or impossible to perform the desired operations.
z If the unit is installed near fluorescent lights, plasma
monitors or other such products or if the unit is
exposed to sunlight, the effects of the light may make it
impossible for the unit to be operated using the wireless
remote control.
Be sure to follow the steps below for installation and use.
• Take steps to ensure that the wireless remote control signal light-
sensing area will not be exposed to the light from fluorescent lights,
plasma monitors or other such products or from the sun.
• Install the unit away from fluorescent lights, plasma monitors and
other such products.
z For about 10 minutes even after the batteries have been
removed from the wireless remote control, the selection
of the operation to be performed (the <CAM1>, <CAM2>,
<CAM3> or <CAM4> button which was pressed last) will
remain stored in the memory.
When a longer period of time elapses, however, the
selection is reset to the status established when the
<CAM1> button was pressed.
<Layout of wireless remote control signal light-sensing areas>
<NOTE>
• The arrows in the figure below show the light-sensing directions in
which the wireless remote control signals travel.
Wireless remote
control signal light‑
sensing area (back
panel, 1 place)
Wireless remote
control signal light‑
sensing area (front
panel, 2 places)
• Top view
• Rear panel view
Approx. 45° Approx. 45°
Wireless remote control (optional accessory)
14

12 V IN
IR ID AUDIO IN
RS-422
SERVICE
MONI OUT 12G SDI OUT
3G SDI OUT G/L IN
LAN
LINK ACT
OPTICAL
1
2
3
4
5
6
7
5
8
6
23
9 10 11 12 14
21 22201918
17
1615
13
Rear panel
Bottom panel
1. Mount bracket for installation surface (supplied
accessory)
Mount this bracket onto the installation surface, and then attach the
camera main unit to the bracket.
2. Drop‑prevention wire
This wire is screwed down to the bottom panel of the camera main
unit. Loop the circle part of the wire around the hook of the mount
bracket.
3. Status display lamp
This lights in the following way depending on the status of the unit.
Orange Light up When the standby status is established
Blink twice When a signal not matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is on
Green Light up When the power is on
Blink twice When a signal matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is on
Blinking
rapidly
When the initialization process is complete
Red Light up When trouble has occurred in the unit
Blinking
slowly
Firmware being updated
Blinking
rapidly
When a PoE++ software authentication error has
occurred
4. Tilt head
This rotates in the right and left direction.
5. Wireless remote control signal light‑sensing area
The light-sensing area is provided in three places, on the front panel
of the camera pedestal and at the top of the rear panel.
6. Hole for securing the camera pedestal
This hole is provided in the bottom panel of the camera pedestal.
7. Camera head
This rotates in the up and down direction.
8. Tally lamp
This comes on or goes off in response to the control from the
controller but only when “On” has been selected as the tally lamp use
setting. The tally lamp is red or green.
9. LAN connector for IP control <LAN LINK/ACT>
This LAN connector (RJ-45) is connected when exercising IP control
over the unit from an external device. Use a LAN cable (category 5e
or better, maximum 100 m (328 ft)) for connection.
Parts and their functions
Camera unit
14 15

10. RS‑422 connector <RS‑422>
This RS-422 connector (RJ-45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
Furthermore, by shorting the R-TALLY signal (2-pin) with the GND
(1-pin), it is possible to light the tally lamp (red) in the camera head
section of the unit.
<NOTE>
• Do not connect PoE cable to the RS-422 port.
• Do not apply a voltage to the R_TALLY_IN signal pin.
• Menu settings enable the output to pin 7 and pin 8 of the red tally
and green tally signals received by the unit. Output is by contact
output, and normally is “OPEN”, then it becomes “MAKE” for output.
(→ page 68)
LAN cable*1(category 5e or above, straight cable),
max. 1000 m (3280 ft)
*1Use of an STP (shielded twisted pair) cable is recommended.
Pin
No. Signal Pin No. Signal
1 GND 5 TXD+
2 R_TALLY_IN 6 RXD+
3 RXD– 7
OPTION_OUT1
4 TXD– 8 OPTION_OUT2
Example OPTION_OUT1, OPTION_OUT2 connector
connections
AW-UE150 OPTION_OUT1
OPTION_OUT2
GND
Voltage: Maximum DC12 V
Current: Maximum 100 mA
11. Service switches <SERVICE>
Perform switch settings before turning the unit on.
12 V IN
IR ID AUDIO IN
RS-422
SERVICE
MONI OUT 12G SDI OUT
3G SDI OUT G/L IN
LAN
LINK ACT
OPTICAL
Service switches
Function Factory settings
SW1 Switches for initialization
(Refer to the explanations in “Initialization 1”
and “Initialization 2”)
OFF
SW2
Always leave at OFF (used for factory
adjustments)
OFF
SW3 OFF
SW4 OFF
Initialization 1
• Reset the user authentication settings and host authentication
settings for network connection.
(This will delete all the registered user information (IDs/passwords)
and host information (IP addresses).)
• With the IR ID switches and service switches set as shown below,
turn on the power of the unit.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• When initialization is complete, the status display lamp on the
front of the unit blinks green. Set the service switches back to their
original positions (SW1 to SW4 all OFF), then restart the unit.
Initialization 2
• The unit is reset to the state it was in at the time of purchase. (All
camera menu setting values and network setting values are reset.)
• With the IR ID switches and service switches set as shown below,
turn on the power of the unit.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• When initialization is complete, the status display lamp on the
front of the unit blinks green. Set the service switches back to their
original positions (SW1 to SW4 all OFF), then restart the unit.
12. HDMI connector <HDMI>
This is the HDMI video output connector.
13. 3G SDI OUT connector <3G SDI OUT>
This is the 3G SDI video signal output connector.
16
Parts and their functions (continued)

14. G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Frequency: 59.94 Hz, 29.97 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/59.94p 1080/59.94p
720/59.94p
1080/29.97p
1080/59.94i
1080/29.97PsF
480/59.94i
2160/29.97p ―
1080/59.94p 1080/59.94p
720/59.94p
1080/59.94i ―
1080/29.97p ―
1080/29.97PsF ―
1080/23.98p
over 59.94i
―
720/59.94p 1080/59.94p
720/59.94p
Frequency: 50 Hz, 25 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/50p 1080/50p
720/50p
1080/25p
1080/50i
1080/25PsF
576/50i
2160/25p ―
1080/50p 1080/50p
720/50p
1080/50i ―
1080/25p ―
1080/25PsF ―
720/50p 1080/50p
720/50p
Frequency: 24 Hz
Format External sync signal input format
Tri‑level sync
2160/24p 1080/24p
1080/24PsF
1080/24p
Frequency: 23.98 Hz
Format External sync signal input format
Tri‑level sync
2160/23.98p 1080/23.98p
1080/23.98PsF
1080/23.98p
1080/23.98PsF
15. DC IN connector <12 V IN> (XLR connector)
Input 12 V DC.
<NOTE>
• Use a DC cable with the following lengths.
For 12 V input: Max. 3 m (9.84 ft) (when using an AWG16 cable)
External DC power supply
Connect after making sure that the output voltage of the external DC
power supply is compatible with the rated voltage of the camera.
Select an output amperage for the external DC power supply with a
margin above the total amperage of the connected devices.
The total amperage of connected devices can be calculated with the
following formula.
Total power consumption ÷ voltage
When the power of the camera is turned on, inrush current is generated.
Insufficient power supply when turning on the power may cause a
malfunction. We recommend that you use an external DC power supply
that can assure double the capacity of the total power consumption of the
camera and connected devices that are turned on by interlock when the
power of the camera is turned on (such as lenses, wireless microphone
receivers).
• Make sure of the pin alignment of the DC output terminal of the
external DC power supply and the camera DC IN connector, and
connect the polarity correctly.
If the +12 V power supply is mistakenly connected to the GND terminal,
it may cause fire or malfunction.
12 V IN
1
23
4
1 GND
2 —
3 —
4 +12 V
HA16RA-4P (77)
Hirose Electric Co.
16. IR ID switches <IR ID>
CAM1 CAM2 CAM3 CAM4
These are used to select the ID of the wireless remote control
(optional accessory). (→ page 27)
The IR ID switch settings “CAM1” to “CAM4” correspond to the
<CAM1> to <CAM4> buttons on the wireless remote control.
17. Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. (→ page 6)
18. AUDIO IN connector <AUDIO IN>
Inputs external audio (microphone, line).
19. Ventilation holes
Blocking the ventilation holes may cause a malfunction. Make sure
there is sufficient space around the ventilation holes.
20. MONITOR OUT connector <MONI OUT>
This is an SDI video signal output connector. Use it in applications
such as displaying the crop position when cropping from 4K to HD
and for monitoring images.
21. 12G SDI OUT connector <12G SDI OUT>
This is a 12G-SDI video signal output connector.
22. Optical connector <OPTICAL>
This is the connector for the SFP+ optical fiber module. By connecting
the optional fiber module, it is possible to output signals converted to
optical signals from SDI signals. Select the fiber module that suits the
signal band*1for each format.
*1• 4K (59.94p, 50p): 12G
• 4K (other than 59.94p, 50p): 6G
• HD (59.94p, 50p): 3G
• HD (other than 59.94p, 50p): 1.5G
<NOTE>
• This unit does not support input by optical signals.
23. Tripod screw holes
(Screw: 1/4-20 UNC, ISO 1222 [6.35 mm (1/4 inches)])
Use these screw holes when securing the unit to a tripod, etc.
16 17
Parts and their functions (continued)

 Output conditions for each video format
Frequency System Format HDMI 12G SDI OUT OPTICAL 3G SDI OUT MONI OUT
59.94Hz
2160/59.94p 2160/59.94p
1080/59.94p*1
2160/59.94p
1080/59.94p*1
2160/59.94p
1080/59.94p*1
1080/59.94p*1
1080/59.94i*11080/59.94i*1
2160/29.97p 2160/29.97p
1080/29.97p
2160/29.97p
1080/29.97p
1080/29.97PsF
2160/29.97p
1080/29.97p
1080/29.97PsF
1080/29.97p
1080/29.97PsF
1080/29.97p
1080/29.97PsF
1080/59.94p 1080/59.94p 1080/59.94p 1080/59.94p 1080/59.94p
1080/59.94i 1080/59.94i
1080/59.94i 1080/59.94i 1080/59.94i 1080/59.94i 1080/59.94i 1080/59.94i
1080/29.97p 1080/29.97p 1080/29.97p 1080/29.97p 1080/29.97p 1080/29.97p
1080/29.97PsF 1080/29.97p 1080/29.97PsF 1080/29.97PsF 1080/29.97PsF 1080/29.97PsF
1080/23.98p over
59.94i
1080/23.98p over
59.94p
1080/23.98p over
59.94i
1080/23.98p over
59.94i
1080/23.98p over
59.94i
1080/23.98p over
59.94i
720/59.94p 720/59.94p 720/59.94p 720/59.94p 720/59.94p 720/59.94p
50Hz
2160/50p 2160/50p
1080/50p*2
2160/50p
1080/50p*2
2160/50p
1080/50p*2
1080/50p*2
1080/50i*21080/50i*2
2160/25p 2160/25p
1080/25p
2160/25p
1080/25p
1080/25PsF
2160/25p
1080/25p
1080/25PsF
1080/25p
1080/25PsF
1080/25p
1080/25PsF
1080/50p 1080/50p 1080/50p 1080/50p 1080/50p
1080/50i 1080/50i
1080/50i 1080/50i 1080/50i 1080/50i 1080/50i 1080/50i
1080/25p 1080/25p 1080/25p 1080/25p 1080/25p 1080/25p
1080/25PsF 1080/25p 1080/25PsF 1080/25PsF 1080/25PsF 1080/25PsF
720/50p 720/50p 720/50p 720/50p 720/50p 720/50p
24Hz 2160/24p 2160/24p
1080/24p
2160/24p
1080/24p
2160/24p
1080/24p 1080/24p 1080/24p
1080/24p 1080/24p 1080/24p 1080/24p 1080/24p 1080/24p
23.98Hz
2160/23.98p 2160/23.98p
1080/23.98p
2160/23.98p
1080/23.98p
1080/23.98PsF
2160/23.98p
1080/23.98p
1080/23.98PsF
1080/23.98p
1080/23.98PsF
1080/23.98p
1080/23.98PsF
1080/23.98p 1080/23.98p 1080/23.98p 1080/23.98p 1080/23.98p 1080/23.98p
1080/23.98PsF 1080/23.98p 1080/23.98PsF 1080/23.98PsF 1080/23.98PsF 1080/23.98PsF
*1When [UHD Crop] is [Crop(720)], output is 720/59.94p.
*2When [UHD Crop] is [Crop(720)], output is 720/50p.
18
Parts and their functions (continued)

 IP video transmission output (multi‑channel display)
• When “Streaming mode” is set to “H.265”
Settings H.265(1) H.265(2) H.264(1) H.264(2) H.264(3) H.264(4) JPEG(1) JPEG(2) JPEG(3)
Resolution
1920 × 1080 1920 × 1080
————
1920×1080
1280×720 1280×720 1280×720
640×360 640×360 640×360 640×360
320×180 320×180 320×180
Frame rate
System
frequency
59.94Hz
60fps 60fps
————
30fps 30fps 30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
50Hz
50fps 50fps
————
25fps 25fps 25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
29.97Hz
30fps 30fps
————
30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
25Hz
25fps 25fps
————
25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
24/23.98Hz
24fps 24fps
————
24fps 24fps 24fps
12fps 12fps 12fps
4fps 4fps 4fps
1fps 1fps 1fps
• The H.265 transmission mode (Transmission priority) cannot be selected.
• When the system frequency is 24/23.98Hz, the resolution for H.265(1) and H.265(2) is limited to 1920×1080.
• You cannot make settings above the resolution and frame rate set by the system format.
• When “Streaming mode” is set to “H.265(UHD)”
Settings H.265(1) H.265(2) H.264(1) H.264(2) H.264(3) H.264(4) JPEG(1) JPEG(2) JPEG(3)
Resolution
3840 × 2160
—————
1920×1080
1280×720
640×360 640×360 640×360
320×180 320×180 320×180
Frame rate
System
frequency
59.94Hz
30fps
—————
30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
50Hz
25fps
—————
25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
29.97Hz
30fps
—————
30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
25Hz
25fps
—————
25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
24/23.98Hz
24fps
—————
24fps 24fps 24fps
12fps 12fps 12fps
4fps 4fps 4fps
1fps 1fps 1fps
• The H.265(UHD) transmission mode (Transmission priority) cannot be selected.
18 19
Parts and their functions (continued)

• When “Streaming mode” is set to “H.264”
Settings H.265(1) H.265(2) H.264(1) H.264(2) H.264(3) H.264(4) JPEG(1) JPEG(2) JPEG(3)
Resolution — —
1920×1080 1920×1080 1920×1080
1280×720 1280×720 1280×720 1280×720 1280×720
640×360 640×360 640×360 640×360 640×360 640×360
320×180 320×180 320×180 320×180 320×180 320×180
Frame rate
System
frequency
59.94Hz
— —
60fps 60fps
30fps 30fps 30fps 30fps 30fps 30fps 30fps
15fps 15fps 15fps 15fps 15fps 15fps 15fps
5fps 5fps 5fps 5fps 5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
50Hz
— —
50fps 50fps
25fps 25fps 25fps 25fps 25fps 25fps 25fps
12.5fps 12.5fps 12.5fps 12.5fps 12.5fps 12.5fps 12.5fps
5fps 5fps 5fps 5fps 5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
29.97Hz
— —
30fps 30fps 30fps 30fps 30fps 30fps 30fps
15fps 15fps 15fps 15fps 15fps 15fps 15fps
5fps 5fps 5fps 5fps 5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
25Hz
— —
25fps 25fps 25fps 25fps 25fps 25fps 25fps
12.5fps 12.5fps 12.5fps 12.5fps 12.5fps 12.5fps 12.5fps
5fps 5fps 5fps 5fps 5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
24/23.98Hz
— —
24fps 24fps
— —
24fps 24fps 24fps
12fps 12fps 12fps
4fps 4fps 4fps
1fps 1fps 1fps
• The available options for the H.264 transmission mode (Transmission priority) are limited to 30fps or lower (excluding 24fps).
• When the system frequency is 24/23.98Hz, the resolution for H.264(1) and H.264(2) is limited to 1920×1080.
• You cannot make settings above the resolution and frame rate set by the system format.
• When “Streaming mode” is set to “H.264(UHD)”
Settings H.265(1) H.265(2) H.264(1) H.264(2) H.264(3) H.264(4) JPEG(1) JPEG(2) JPEG(3)
Resolution — —
3840 × 2160
———
1920×1080
1280×720
640×360 640×360 640×360
320×180 320×180 320×180
Frame rate
System
frequency
59.94Hz
— —
60fps
———
30fps 30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
50Hz
— —
50fps
———
25fps 25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
29.97Hz
— —
30fps
———
30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
25Hz
— —
25fps
———
25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
24/23.98Hz
— —
24fps
———
24fps 24fps 24fps
12fps 12fps 12fps
4fps 4fps 4fps
1fps 1fps 1fps
• The H.264(UHD) transmission mode (Transmission priority) cannot be selected.
20
Parts and their functions (continued)