Panasonic WV-NW484S - i-Pro Network Camera User manual

Network Camera
Operating Instructions
Model No. WV-NW484S
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.

2
WARNING:
• This apparatus must be earthed.
• All work related to the installation of this product
should be made by qualified service personnel
or system installers.
• The connections should comply with local
electrical code.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SA 1965
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to the presence
of uninsulated "dangerous
voltage" within the product's
enclosure that may be of
sufficient magnitude to
constitute a risk of electric
shock to persons.
SA 1966
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
This Class A digital apparatus complies with
Canadian ICES-003.
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense. FCC
Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral
devices). Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this equipment.
The serial number of this product may be found
on the surface of the unit.
You should note the serial number of this unit
in the space provided and retain this book as a
permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
For Canada
For U.S.A

3
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Clean only with dry cloth.
6) Do not block any ventilation openings. Install in accordance with the manufacturer's instruc-
tions.
7) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
8) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
9) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10) Only use attachments/accessories specified by the manufacturer.
11) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
12) Unplug this apparatus during lightning storms or when unused for long periods of time.
Important Safety Instructions
S3125A

4
THIS PUBLICATION IS PROVIDED "AS IS"
WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANT-
ABILITY, FITNESS FOR ANY PARTICULAR
PURPOSE, OR NONINFRINGEMENT OF
THE THIRD PARTY’S RIGHT.
THIS PUBLICATION COULD INCLUDE
TECHNICAL INACCURACIES OR
TYPOGRAPHICAL ERRORS. CHANGES
ARE ADDED TO THE INFORMATION
HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION
AND/OR THE CORRESPONDING
PRODUCT (S).
IN NO EVENT SHALL MATSUSHITA
ELECTRIC INDUSTRIAL CO,.LTD. BE
LIABLE TO ANY PARTY OR ANY PERSON,
EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE
PRODUCT, FOR THE CASES, INCLUDING
BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING
WITHOUT LIMITATION, DIRECT OR
INDIRECT, SPECIAL, CONSEQUENTIAL
OR EXEMPLARY, ARISING OUT OF OR
RELATING TO THE PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE
CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE
USER;
(3) UNAUTHORIZED DISASSEMBLE,
REPAIR OR MODIFICATION OF THE
PRODUCT BY THE USER;
(4) INCONVENIENCE OR ANY LOSS
ARISING WHEN IMAGES ARE NOT
DISPLAYED, DUE TO ANY REASON OR
CAUSE INCLUDING ANY FAILURE OR
PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL
INCONVENIENCE, OR LOSS OR
DAMAGE, ARISING OUT OF THE
SYSTEM COMBINED BY THE DEVICES
OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR
DAMAGES, BROUGHT BY ANY
PERSON OR ORGANIZATION BEING A
PHOTOGENIC SUBJECT, DUE TO
VIOLATION OF PRIVACY WITH THE
RESULT OF THAT SURVEILLANCE-
CAMERA'S PICTURE, INCLUDING
SAVED DATA, FOR SOME REASON,
BECOMES PUBLIC OR IS USED FOR
THE PURPOSE OTHER THAN
SURVEILLANCE;
(7) LOSS OF REGISTERED DATA CAUSED
BY ANY FAILURE.
Limitation of Liability
Disclaimer of Warranty

5
Preface
This video surveillance camera is equipped with a 10BASE-T/100BASE-TX terminal
(network terminal) for connection to a network.
This network terminal is used to establish a connection between the camera and a LAN
(Local Area Network) or other network (e.g. Internet) so that images from the camera can
be checked on a personal computer (from here on, "PC") on the network.
..............................................................................................................................
Note
• To check images from the camera on a PC, the PC's network environment must first be
set up. A web browser must also be installed on the PC.
...................................................................................................................................
Super Dynamic III (SUPER-D III )
Auto Back Focus function
VMD (Video Motion Detector) function for detecting motion of an intruder, etc. in the
monitoring area and sounding an alarm by an alarm signal
Progressive output (motion adaptive interlace/progressive conversion function)
Dual Encode Function for simultaneous transmission of JPEG and MPEG-4
Power over Ethernet (IEEE802.3af-compliant, from here on, "PoE") function
SD memory card slot
Features

Preface (continued)
6
The Instruction Manual for this camera is comprised of three parts: this book, and the
Operating Manual (PDF) and Setup Manual (PDF).
This book explains how to install the camera, and how to connect and set up the network.
For details on how to operate and set up the camera, refer to the " Operating Manual/Setup
Manual" in the CD-ROM (provided). To read the PDF manual, Adobe Systems Incorpo-
rated's Adobe®Reader®is required.
..............................................................................................................................
Note
• When the PC is used in an environment other than that recommended, the image
refresh rate may slow down, operations in the web browser may no longer be possible,
or other problems may occur.
...................................................................................................................................
About these operating instructions
System requirements for a PC
CPU Pentium®4 2.4 GHz or faster
Memory 512 MB or more
Network 10BASE-T/100BASE-TX port x 1
Image display Resolution: 1024 x 768 pixels or more
Color scheme: True Color 24 bits or more
Supported OS Microsoft®Windows®2000 Professional SP4*
Microsoft®Windows®XP Home Edition SP2
Microsoft®Windows®XP Professional SP2
Web Browser Microsoft®Internet Explorer®6.0 SP2
Microsoft®Internet Explorer®7.0
* When supported OS is Microsoft®Windows®2000 Professional
SP4, Microsoft®Internet Explorer®6.0 SP1
Other CD-ROM drive (for using Operating Instructions and software)
DirectX®9.0c or later
Adobe®Reader®(for reading Operating Instructions in CD-ROM)

7
• Microsoft, Windows, ActiveX and DirectX are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
• Intel and Pentium are either registered trademarks or trademarks of Intel Corporation in
the United States and/or other countries.
• Adobe and Reader are either registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
• The SD logo is a trademark.
• Other names of companies and products contained in these operating instructions may
be trademarks or registered trademarks of their respective owners.
As you will use this product connected to a network, your attention is called to the following
security risks.
(1) Leakage or theft of information through this product
(2) Use of this product for illegal operations by persons with malicious intent
(3) Interference with or stoppage of this product by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.
• Use this product in a network secured by a firewall, etc.
• If this product is connected to a network that includes PCs, make sure that the system is
not infected by computer viruses or other malicious entities (using a regularly updated
anti-virus program, anti-spyware program, etc.).
• Protect your network against unauthorized access by restricting users to those who log
in with an authorized user name and password.
• Apply measures such as user authentication to protect your network against leakage or
theft of information, including image data, authentication information (user names and
passwords), alarm mail information, FTP server information and DDNS server informa-
tion.
• Do not install the camera in locations where the camera or the cables can be destroyed
or damaged by persons with malicious intent.
Trademarks and Registered Trademarks
Network Security

8
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disclaimer of Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
System requirements for a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Trademarks and Registered Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Network Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Precaution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Names of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Super Dynamic III (SUPER-D III ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Motion Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Progressive output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Privacy Zone Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Auto Back Focus Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Recording to an SD Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Special Power Supply and Cable Installation Not Required (Power over Ethernet) . . . 17
Dual Encoding for Higher Efficiency Operation in Network Environments . . . . . . . . . . 17
Installation and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Before Starting Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Handling SD Memory Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Insertion and Removal of SD Memory Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Heater Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
How to Install the Heater Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connection Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installing the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using the Panasonic IP Setup Software to Set Up the Camera . . . . . . . . . . . . . . . . . . 35
Monitor Images on a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Monitor images from a single camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Monitor images from multiple cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9
Action at an alarm occurrence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Alarm type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Action at an alarm occurrence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Viewing Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Displaying the Help screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

10
Precaution
The camera does not have a power
switch.
In order to the power off, turn the power
breaker off.
Note the following to ensure long-term
trouble-free operation.
Long operation under high temperatures
and high humidity can cause components
to deteriorate and shorten camera life.
(Less than +35°C (95°F) is recommended)
Make sure that the camera is installed in a
location where it is not directly exposed to
heat from a radiator, heater, etc.
Do not touch the dome cover with your
bare hands.
A dirty dome cover causes deterioration of
picture quality.
Handle the camera carefully.
Do not drop the camera, or subject it to
strong impact or vibration.
Doing so may cause a malfunction.
About the PC to be used
Displaying the same image on CRT type
PC monitors for a long time may damage
the monitor. We recommend using a
screen saver.
Cleaning the camera
Before cleaning the camera, turn the power
off. Not doing so may cause injury.
Do not wipe or use volatile solutions such
as benzene or paint thinner on the camera.
Doing so may discolor the case. When
using a chemically-treated cloth, read and
follow the precautions for the cloth.
In the case of stubborn dirt
Wipe with a soft cloth moistened in a weak
solution of water and neutral kitchen
detergent. Wring all excess moisture from
the cloth before wiping. Next, wipe off all
remaining solution with a soft, dry cloth.
Product Information
Check the product ID, power requirements,
and other information marked on the rear
and bottom of the product.
Refresh Interval
The refresh interval may be longer
depending on the network environment, PC
performance, photographic subject, access
traffic, etc.
Cleaning the lens
Use lens cleaning paper (like the type
available for cleaning eyeglasses or a
camera lens) to clean the lens. Alcohol-
based solvents may be used for cleaning
the lens. Do not use glass cleaners or paint
thinners.

11
MPEG-4 Visual patent portfolio license
This product is licensed under the MPEG-4
Visual patent portfolio license for the
personal and non-commercial use of a
consumer for (i) encoding video in
compliance with the MPEG-4 Visual
Standard ("MPEG-4 Video") and/or (ii)
decoding MPEG-4 Video that was encoded
by a consumer engaged in a personal and
non-commercial activity and/or was
obtained from a video provider licensed by
MPEG LA to provide MPEG-4 Video. No
license is granted or shall be implied for
any other use. Additional information
including that relating to promotional,
internal and commercial uses and licensing
may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
SD Memory Card
• Before inserting an SD memory card,
turn the camera off. If the SD memory
card is inserted while the camera is still
turned on, the SD memory card may
not function properly, or the data
recorded on the SD memory card may
be damaged.
For details on how to insert and remove
SD memory cards, see page 32.
• Format unformatted SD memory cards
on this system before use. When an SD
memory card is formatted, all content
recorded on the card will be erased. If
an unformatted SD memory card or an
SD memory card formatted on a
different system is used on this camera,
the SD memory card may not function
properly, or the camera's performance
may be reduced.
• For details on how to format SD
memory cards, refer to the "Setup
Manual."
• We recommend using SD memory
cards whose operation has already
been confirmed (→page 16). When an
SD memory card other than one
recommended by Panasonic is used,
the SD memory card may not function
properly, or the camera's performance
may be reduced.
CCD Color Filter Burn-in
Intense light concentrated on one spot for a
long period can cause deterioration of the
CCD internal color filters, and discoloration
of the affected part. Even if the position of a
fixed camera is changed, the discoloration
at the previous location of the concentrated
light will remain on the screen.

Precaution (continued)
12
Do not point the camera at a strong light
source.
• Intense light such as that produced by a
spotlight concentrated on one part of
the screen can cause blooming
(rainbow around the strong light) or
smearing (vertical stripes above and
below the strong light).
Consumables
The item listed below is a consumable.
Replace it using the service life values as
guides. Note that actual service life is
affected by the operating environment and
conditions.
Cooling fan: Approx. 30,000 hours
Dehumidifying Element
• This camera has a built-in dehumidify-
ing element to maintain a low-humidity
state inside the camera. This prevents
condensation from forming.
• Condensation forms due to tempera-
ture, humidity, weather and other
conditions, and may take time to clear
up.
• Do not block the surface of the
dehumidifying element.
Smearing
Blooming
Bright subject
Dehumidifying
element

13
Names of Components
(1) Enclosure
(2) Mounting bracket (accessory)
(3) Network cable
(6) Tilting lock screw
(9) Focus lever
(5) Power cable
(4) Alarm I/O cable
(11) Zoom lever
(7)Tilt adjustment
seat
(10) Panning lock screw
(8) Panning table
(19) Monitor output jack
(20) SD memory card slot
(14) ABF button (ABF)
(13) INIT button (INIT)
(15) LED ON/OFF switch button
(16) Access LED (ACT)
(12) Heater Unit connector
(17) Link LED (LINK)
(18) ABF LED (ABF)
(21) SD memory card error LED

Names of Components (continued)
14
(1) Enclosure
(2) Mounting bracket (accessory)
(3) Network cable
(4) Alarm I/O cable
(5) Power cable
(6) Tilting lock screw
Fixes the tilt position after adjusting.
(7) Tilt adjustment seat
Adjusts the screen tilt.
(8) Panning table
Adjusts the horizontal angle of the
camera.
(9) Focus lever
Fixes the focus position.
(10) Panning lock screw
Fixes the panning position after
adjusting.
(11) Zoom lever
Fixes the zoom position after adjusting.
(12) Heater output connector
Used for connecting the heater unit
(sold separately) cable.
(13) INIT button (INIT)
Used for initializing setup.
(14) ABF button (ABF)
Used for starting ABF.
(15) LED ON/OFF switch button
Used for turning the link LED and
access LED on and off.
.........................................................
Note
• The link LED and the access LED light
if the LED ON/OFF button is ON and
the LED display setting (→Setup
Manual) on the computer is set to "ON".
The LEDs do not light if the LED ON/
OFF button is OFF or the computer's
LED display settings is set to "OFF".
..............................................................
Important
• In regular operation, set this switch to
off. Lighting of the LEDs may reflect on
the dome and be included in the image
on screen.
(16) Access LED (ACT)
This LED indicates the reception status.
(17) Link LED (LINK)
This LED indicates the network link
status.
(18) ABF LED (ABF)
This LED indicates the busy status of
the ABF.
(19) Monitor output jack
Used for connecting the monitor for
confirming images at camera installa-
tion.
(20) SD memory card slot
(21) SD memory card error LED
This LED indicates the SD memory
card error status.

15
Functions
When there is wide variation between the illumination of light and dark areas of the location
being monitored, the camera adjusts the lens iris in accordance with the bright areas. This
causes loss of detail in dark areas. Conversely, adjusting lens brightness for the dark areas
causes brighter areas to become washed out.
SUPER-D
III digitally combines an image that is set up for a clear view of bright areas with
an image that is set up for a clear view of dark areas, creating a final image that preserves
overall detail.
This function outputs an alarm signal when motion is detected in the monitoring area, such
as the camera being covered with a cloth or its cover, or the camera's orientation being
changed, during monitoring.
..............................................................................................................................
Note
• The motion detector function is not exclusively for preventing theft, fire, etc. The
manufacturer assumes no responsibility for any accidents that occur or any losses
incurred while this product is being used.
...................................................................................................................................
Super Dynamic III (SUPER-D III )
Motion Detector
Hard to see dark areas Hard to see bright areas
Digital combination
reproduces a clear view

Functions (continued)
16
Jagged edges that are unique to interlaced cameras and that occur in areas with movement
are corrected by the motion adaptive interlace/progressive conversion function and
converted to progressive images. This allows both still and moving objects to be captured as
well-defined images.
The privacy zone function allows you to mask specific areas, such as housing, of a
monitored scene from view.
Back focus can be automatically adjusted by operating the buttons on the camera, which
makes installation easier. Back focus can also be adjusted on the PC after the camera is
installed.
When switching between color and black and white images, the back focus is automatically
adjusted and focus deviation is corrected.
Camera images can be saved to an SD memory card when an alarm occurs.
Images can also be backed up when a network failure occurs.
..............................................................................................................................
Note
• This operation has already been confirmed on the following SD memory cards:
Panasonic SD memory cards (64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2 GB)
SDHC memory card is not supported.
...................................................................................................................................
Progressive output
Privacy Zone Setting
Auto Back Focus Function
Recording to an SD Memory Card

17
Power can be supplied to the camera and images transmitted on a single LAN cable by
connecting to PoE-compatible network devices. Special installation of a power supply for the
camera and video cables is not required.
MPEG-4 and JPEG can be output at the same time.
MPEG-4 operation when monitoring in real time or from a remote site, and JPEG operation
when recording and verifying images at high quality can both be achieved at the same time
in a network environment.
Special Power Supply and Cable Installation Not Required
(Power over Ethernet)
Dual Encoding for Higher Efficiency Operation in Network
Environments

18
Installation and Connections
Installation Precautions
The following describes how to install the camera.
Before you install and connect the camera, check and prepare the required peripheral
devices and cables.
Before you connect the camera, turn off all devices to be connected, such as this camera
and PC.
Camera Installation Location
Discuss the installation location for the
camera with your retailer, and select a
place that is strong enough for the installa-
tion.
• Install the camera on a ceiling
(concrete, etc.) at a location that is
sufficiently strong to support it.
• Install the camera body on the
foundation section of the building or
sections having sufficient bearing
strength.
This camera is for installation under
eaves.
• Do not install it in areas exposed to
direct sunlight or rain.
Never install or use the camera in the
following locations.
• Near a swimming pool or other areas
where chemicals are used.
• Food preparation areas and other
locations where there are large
amounts of steam vapor and oil, in
flammable atmospheres, other special
environments.
• Areas where radiation, X-rays, strong
electric waves, or magnetism is
generated.
• At sea, in coastal areas, or in areas
where corrosive gas is being
generated.
• Areas outside of the allowable ambient
operating temperature range
(→page 47).
• On a motor vehicle, a boat, or other
areas subject to strong vibration.
(This camera is not designed for use on
a vehicle.)
• When installing the camera on a ceiling
of insufficient strength, reinforce the
ceiling.
When not in use, always remove the
unit.
About White Balance
White balance may not be correctly
obtained in the following instances:
• When capturing subjects having
extremely little white or subjects close
to a single color.
• When capturing images outdoors at
dawn or dusk or in low illumination.
• When capturing images having
extremely different color temperatures
(e.g. in color lighting).

19
About Static Electricity Removal
Before installing the camera, touch a metal
case or other metallic parts with your hand
to remove static electricity from your body.
Do not install in areas subjected to high
amounts of humidity or dust.
Doing so may cause internal components
to damage more easily or malfunction.
Do not wire cables near power lines.
Configure the power supply to the
camera so that it can be turned on and
off.
The camera does not have a power switch,
so configure the power supply to the
camera so that it can be turned on and off.
Network Connection
Pay attention to the following points when
using the camera's network cable to
connect to a network.
• Wire and install the camera so that the
network will not be influenced by
lightning surges, etc.
• Pan and tilt cannot be used in combina-
tion with this camera.
Tightening the Screws
Screws should be tightened sufficiently in
accordance with the materials and
structure of the installation location. After
tightening the screws, visually inspect them
to make sure there is no unevenness and
that each screw is tight.
Screws should be ordered separately.
The camera does not come with screws.
Choose screws in accordance with the
materials and structure of the installation
location.
Electrical Wave Interference
The image may fluctuate near TV or radio
transmission antennas, or near strong
electric or magnetic fields (e.g. motors or
transformers). In this case, setup a special-
ized thin conduit and pass the cable
through it.
Power Supply by PoE
Use a PoE-compatible (IEEE802.3af-
compliant) hub or power supply unit.

20
Before Starting Installation
The following procedures are for installing the camera on walls and ceilings.
Important
• The type of screws for the installation depend on the material at the location in which
you will install the bracket (included). However, do not use wood screws or nails.
Metal material: Use M6 or M5 bolts and nuts for mounting.
Concrete wall: Use M6 or M5 anchor bolts for mounting.
• Be sure that the arrow on the installation bracket is pointing upwards.
• A pull-out force in excess of 294 N {30 kgf} is required for each screw used in the
installation.
• Use sufficient reinforcement for installations on ceilings that are made of gypsum board
and are weak.
Fixing the bracket (accessory)
• Use the bracket to install the camera on a wall or ceiling that is provided with a hole for
passing the cable through or on exposed piping.
• Screws for fixing the bracket to a wall or ceiling are not provided. Choose screws in
accordance with the materials and structure of the installation location.
• Screws for fixing the camera to the bracket are provided with the camera.
(Recommended tightening torque M4 : 0.8 N·m {8 kgf·cm}
M5 : 1.5 N·m {15 kgf·cm}
M6 : 2.5 N·m {25 kgf·cm})