Panasonic SA-AKX34PH User manual

© Panasonic Corporation 2012. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
PSG1202003CE
CD Stereo System
Model No. SA-AKX34PH
SA-AKX34PN
Product Color: (K)...Black Type
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 3
1.1. General Guidelines---------------------------------------- 3
1.2. Before Use (For PH only)-------------------------------- 3
1.3. Before Repair and Adjustment------------------------- 3
1.4. Protection Circuitry---------------------------------------- 4
1.5. Caution For Fuse Replacement------------------------ 4
1.6. Safety Parts Information--------------------------------- 5
2 Warning-------------------------------------------------------------- 6
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatic Sensitive (ES) Devices -------------- 6
2.2. Precaution of Laser Diode------------------------------- 7
2.3. Service caution based on Legal restrictions-------- 8
2.4. Handling Precautions for Traverse Unit-------------- 9
3 Service Navigation --------------------------------------------- 11
3.1. Service Information-------------------------------------- 11
4 Specifications----------------------------------------------------12
5 General/Introduction-------------------------------------------13
5.1. Media Information---------------------------------------- 13
6 Location of Controls and Components------------------14
6.1. Remote Control Key Button Operation ------------- 14
6.2. Main Unit Key Button Operation---------------------- 15
7 Installation Instructions --------------------------------------16
7.1. Speaker and A/C Connection-------------------------16
8 Service Mode-----------------------------------------------------17
8.1. Cold-Start -------------------------------------------------- 17
8.2. Doctor Mode Table--------------------------------------- 18
Please refer to the original service manual for:
CD Mechanism Unit (BRS11C), Order No. PSG1201019AE
Speaker system SB-AKX34PN-K, Order No. PSG1202004CE

2
8.3. Reliability Test Mode (CD Mechanism Unit
(BRS11C)) -------------------------------------------------21
8.4. Self-Diagnostic Mode -----------------------------------22
8.5. Self-Diagnostic Error Code Table--------------------22
8.6. Sales Demonstration Lock Function ----------------23
9 Troubleshooting Guide----------------------------------------24
9.1. Part Location ----------------------------------------------24
9.2. Troubleshooting Guide for F61 and/or F76--------27
9.3. D-Amp IC Operation & Control -----------------------28
10 Service Fixture & Tools ---------------------------------------30
11 Disassembly and Assembly Instructions---------------31
11.1. Disassembly Flow Chart--------------------------------32
11.2. Main Components and P.C.B. Locations-----------33
11.3. Disassembly of Top Cabinet---------------------------34
11.4. Disassembly of Front Panel Unit---------------------35
11.5. Disassembly of Panel P.C.B.--------------------------36
11.6. Disassembly of Memory LED P.C.B.----------------38
11.7. Disassembly of Remote Sensor P.C.B.-------------38
11.8. Disassembly of USB P.C.B. ---------------------------39
11.9. Disassembly of Music Port P.C.B. -------------------39
11.10. Disassembly of CD Lid----------------------------------40
11.11. Disassembly of Main P.C.B.---------------------------40
11.12. Replacement of Voltage Regulator IC
(IC2010) ----------------------------------------------------42
11.13. Replacement of Voltage Regulator IC
(IC2011) ----------------------------------------------------43
11.14. Replacement of Audio Digital Amp IC
(IC5800) ----------------------------------------------------44
11.15. Disassembly of SMPS P.C.B.-------------------------45
11.16. Replacement of Switching Regulator IC
(IC5701) ----------------------------------------------------46
11.17. Replacement of Rectifier Diode (D5702)-----------47
11.18. Replacement of Rectifier Diode (D5801)-----------48
11.19. Replacement of Rectifier Diode (D5802)-----------50
11.20. Replacement of Regulator Diode (D5803)---------51
11.21. Disassembly of CD Mechanism Unit
(BRS11C) --------------------------------------------------53
11.22. Disassembly of CD Interface P.C.B.-----------------55
11.23. Disassembly of CD Servo P.C.B.---------------------55
11.24. Disassembly of Rear Panel----------------------------56
11.25. Disassembly of Voltage Selector P.C.B.------------57
12 Service Position-------------------------------------------------58
12.1. Checking and Repairing of Main P.C.B.------------58
12.2. Checking and Repairing of Panel P.C.B.-----------58
12.3. Checking and Repairing of SMPS P.C.B.----------59
12.4. Checking and Repairing of CD Servo P.C.B.
(Side A)-----------------------------------------------------60
12.5. Checking and Repairing of CD Servo P.C.B.
(Side B)-----------------------------------------------------61
13 Simplified Block Diagram ------------------------------------63
13.1. Power Block Diagram-----------------------------------63
14 Block Diagram ---------------------------------------------------64
14.1. Servo & System Control--------------------------------64
14.2. IC Terminal Chart-----------------------------------------66
14.3. Audio --------------------------------------------------------67
14.4. Power Supply ---------------------------------------------68
15 Wiring Connection Diagram---------------------------------70
16 Schematic Diagram---------------------------------------------71
16.1. Schematic Diagram Notes-----------------------------71
16.2. CD Servo Circuit------------------------------------------73
16.3. Main(MICON) Circuit------------------------------------77
16.4. Main(D-Amp) Circuit ------------------------------------ 85
16.5. Panel Circuit ---------------------------------------------- 87
16.6. Remote Sensor, USB, Music Port and
Memory LED Circuit------------------------------------- 89
16.7. CD Interface and Voltage Selector Circuit--------- 90
16.8. SMPS Circuit---------------------------------------------- 91
17 Printed Circuit Board------------------------------------------ 93
17.1. CD Servo P.C.B. ----------------------------------------- 93
17.2. Main P.C.B. (Side A)------------------------------------ 94
17.3. Main P.C.B. (Side B)------------------------------------ 95
17.4. Panel, Remote Sensor, USB and Music Port
P.C.B.------------------------------------------------------- 96
17.5. Memory LED and CD Interface P.C.B-------------- 97
17.6. SMPS and Voltage Selector (PH) ------------------- 98
17.7. SMPS P.C.B. (PN)--------------------------------------- 99
18 Appendix Information of Schematic Diagram -------101
18.1. Voltage & Waveform Chart---------------------------101
18.2. Illustration of ICs, Transistor and Diode-----------108
18.3. Terminal Function of ICs------------------------------109
19 Exploded View and Replacement Parts List---------- 111
19.1. Exploded View and Mechanical replacement
Part List --------------------------------------------------- 111
19.2. Electrical Replacement Part List--------------------117

3
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, carry out the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1Mand 5.2M.
When the exposed metal does not have a return path to the chassis, the reading must be
1.1.2. Leakage Current Hot Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5k, 10 watts resistor, in parallel with a 0.15F capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent)
may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the
limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is
returned to the customer.
Figure 1
1.2. Before Use (For PH only)
Be sure to disconnect the mains cord before adjusting the voltage selector.
Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will be
used. (If the power supply in your area is 110V ~ 127V or 220V ~ 240V, set to the “110V ~ 127V or 220V ~ 240V” position.)
Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries,
the correct voltage is already set.)
1.3. Before Repair and Adjustment
Disconnect AC power to discharge unit AC Capacitors as such (C5700, C5701, C5703, C5704 (For PH), C5705 (For PH), C5708)
through a 10 , 10 W resistor to ground.
Caution:
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 110~127 V / 220~240 V, 50/60 Hz in Power ON, FM Tuner, No Signal, volume minimal mode should be
~ 600 mA (PH).
Current consumption at AC 120 V, 60 Hz in Power ON, FM Tuner, No Signal, volume minimal mode should be ~ 600 mA (PN).

4
1.4. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.5. Caution For Fuse Replacement

5
1.6. Safety Parts Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams, Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.
Safety Ref No. Part No. Part Name & Description Remarks
8 REX1536 1P RED WIRE (VOLTAGE SELEC-
TOR-SMPS)
PH
9 REXX1122-J 1P BLACK WIRE (VOLTAGE SELEC-
TOR-SMPS)
PH
20 RKMX1011-K1 TOP CABINET
21 RGRX1008M-A REAR PANEL PN
21 RGRX1008N-A REAR PANEL PH
301 RAE1034Z-V TRAVERSE ASS'Y
A2 K2CB2YY00059 AC CORD PN
A2 K2CQ2CA00007 AC CORD PH
A3 RQT9617-M O/I BOOK (Sp) PN
A3 RQT9619-M O/I BOOK (Sp) PH
PCB9 REP4783F SMPS P.C.B. (RTL) PH
PCB9 REP4783DA SMPS P.C.B. (RTL) PN
PCB11 REP4783F VOLTAGE SELECTOR P.C.B. (RTL) PH
DZ5701 ERZV05Z471CS ZNR
S5701 K0ABCA000007 SW AC VOLTAGE SELECTOR PH
L5706 G0B612H00002 LINE FILTER PH
L5707 G0B612H00002 LINE FILTER PN
T5701 G4DYZ0000051 MAIN TRANSFORMER PH
T5701 G4DYZ0000060 MAIN TRANSFORMER PN
T5751 ETS19AB2E6AG SUB TRANSFORMER
T6000 G4DYA0000214 SWITCHING TRANSFORMER
PC5701 B3PBA0000503 PHOTO COUPLER
PC5702 B3PBA0000503 PHOTO COUPLER
PC5720 B3PBA0000503 PHOTO COUPLER
PC5799 B3PBA0000503 PHOTO COUPLER
F1 K5D632BK0007 FUSE PH
F1 K5D802APA008 FUSE PN
TH5000 D4CC11040013 THERMISTOR
TH5702 D4CAA2R20001 THERMISTOR
TH5860 D4CC11040013 THERMISTOR
TH5861 D4CC11040013 THERMISTOR PN
P5701 K2AA2B000011 AC INLET PH
P5701 K2AB2B000007 AC INLET PN
R5708 ERJ8GEYJ155V 1.5M 1/4W
R5709 ERJ8GEYJ155V 1.5M 1/4W
C5700 F1BAF471A013 470pF
C5701 F0CAF104A105 0.1uF
C5703 F0CAF224A105 0.22uF
C5704 F1BAF471A013 470pF PH
C5705 F1BAF471A013 470pF PH
C5708 F1BAF1020020 1000pF

6
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive
(ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).

7
2.2. Precaution of Laser Diode
Caution:
This product utilizes a laser diode with the unit turned “on”, invisible laser radiation is emitted from the pickup lens.
Wavelength: 790 nm (CD)
Maximum output radiation power from pickup: 100 W/VDE
Laser radiation from the pickup unit is safety level, but be sure the followings:
1. Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pickup unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pickup lens for a long time.

8
2.3. Service caution based on Legal restrictions
2.3.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)

9
2.4. Handling Precautions for Traverse Unit
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the traverse unit.
2.4.1. Cautions to Be Taken in Handling the Optical Pickup Unit
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed
should be short-circuited with a short pin or a clip.
3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexi-
ble cable, cut off the antistatic FPC.

10
2.4.2. Grounding for electrostatic breakdown prevention
Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electric-
ity in the working environment. Proceed servicing works under the working environment where grounding works is completed.
2.4.2.1. Worktable grounding
1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.
2.4.2.2. Human body grounding
1. Use the anti-static wrist strap to discharge the static electricity form your body.

11
3 Service Navigation
3.1. Service Information
This service manual contains technical information which will allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
•CD Mechanism Unit (BRS11C):
1) This model uses CD Mechanism Unit (BRS11C).
•Micro-processor:
1) The following components are supplied as an assembled part.
- Micro-processor IC, IC2003 (RFKWMAKX34M0)
•Speaker System:
1) This model uses Speaker System, SB-AKX34PN-K.

12
4 Specifications
Amplifier section
RMS output power stereo mode
Front Ch (both ch driven) 190 W per channel (4), 1
kHz, 10% THD
250 W per channel (4), 1
kHz, 30% THD
Total RMS stereo mode power 380 W (10% THD)
500 W (30% THD)
PMPO Output Power 5500 W
Tuner, terminals section
Preset station FM 30 stations
AM 15 stations
Frequency modulation (FM)
Frequency range 87.50 to 108.00 MHz
(50 kHz step)
Antenna terminals 75 (unbalanced)
Amplitude modulation (AM)
Frequency range 522 kHz to 1629 kHz
(9 kHz step)
Music port (front)
Sensitivity 100 mV, 4.7 k
Terminal Stereo, 3.5 mm jack
Aux Input RCA pin jack
Disc section
Discs played (8 cm or 12 cm) CD, CD-R/RW(CD-DA, MP3*)
Pick up
Wavelength 790 nm(CD)
Laser power CLASS 1
Audio output (disc)
Number of channels 2 ch (FL, FR)
FL = Front left channel
FR = Front right channel
*MPEG-1 Layer 3
USB section
USB Port
USB standard USB 2.0 full speed
Media file format support MP3(*.mp3)
USB device file system FAT12, FAT16, FAT32
USB port power 500 mA (max)
Bit rate 16 kbps to 320 kbps (playback)
USB Recording
Bit rate 128 kbps
USB recording speed 1x, 3x max (CD only)
Recording file format MP3 (*.mp3)
Internal memory section
Memory
Memory size 2 GB
Media file format support MP3 (*.mp3)
Memory Recording
Bit rate 128 kbps
Memory recording speed 1x, 3x max (CD only)
Recording file format MP3 (*.mp3)
Capacity of total songs recorded
(use 128 kbps, approximately 1
song = 4 mins)
510 songs
General
Power consumption 77 W
PowerConsumptioninstandby
mode 0.3 W (approximate)
Power supply AC 110 to 127/220 to 240 V,
50/60 Hz (for PH)
AC 120 V, 60 Hz (for PN)
Dimensions (W x H x D) 220 mm x 334 mm x 245 mm
Mass 3 kg
Operating temperature range 0 C to +40 C
Operating humidity range 35% to 80% RH
(no condensation)
1. Specifications are subject to change without notice.
Mass and dimension are appropriate
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
System: SC-AKX34PH-K Main Unit: SA-AKX34PH-K
Front Speakers: SB-AKX34PN-K
System: SC-AKX34PN-K Main Unit: SA-AKX34PN-K
Front Speakers: SB-AKX34PN-K

13
5 General/Introduction
5.1. Media Information

14
6 Location of Controls and Components
6.1. Remote Control Key Button Operation

15
6.2. Main Unit Key Button Operation

16
7 Installation Instructions
7.1. Speaker and A/C Connection

17
8 Service Mode
8.1. Cold-Start
Here is the procedure to carry out cold-start or initialize to shipping mode.
1. Unplug AC power cord
2. Press & hold [POWER] button
3. Plug AC power cord while [POWER] button being pressed
FL Display will show “_ _ _ _ _ _ _ _”
4. Release [POWER] button

18
8.2. Doctor Mode Table
8.2.1. Doctor Mode Table 1
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Doctor Mode
EEPROM
checksum
check
(Decimal)
To enter into Doctor Mode In CD Mode:
1. Press [ ] button on
main unit follow by [4]
and [7] on remote
control.
In CD mode:
1. Enter Doctor Mode
2. To exit, press [DELETE]
button on remote control
Displaying of
1. Year Develop.
2. Model Type.
3. ROM Type.
4. Firmware Version.
23 41
Version No. (001 ~ 999) specific for each firmware
Cold Start To active cold start upon next AC
power up when reset start is
execute the next time .
In Doctor Mode :
1. Press [SLEEP] button
on remote control.
or, press [POWER, /I] button
on Main Unit

19
8.2.2. Doctor Mode Table 2
FL Display
Key Operation
Front Key
Item
Description
Mode Name
Volume Setting
Check
FL Display
Check
To check the volume setting of a main
unit.
To check the FL segment display
All segment will light up while all LED
blink at 0.5s,intervals.(if any)
In Doctor Mode :
1. Press [7], [8], [9] button
on remote control.
In Doctor mode :
1. Press [1] button on
remote control.
Press [7]: VOL50
Press [8]: VOL35
Press [9]: VOL0
Volume
In this mode, the tray will open &
close.
Note: Refer to Section 8.3 Fig 1 for
process flow .
The counter will
increment by one .
When reach 9999
will change to 0000
Cancellation Display
BRS11C Reliability
Test (Loading)
To determine CD Mechanism Unit
(BRS11C) Open/Close operation.
Note: Refer to Section 8.3 Fig 2. for
process flow .
The counter will
increment by one .
When reach 9999
will change to 0000
Cancellation Display
BRS11C Reliability
Test (Traverse)
Test
To determine CD Mechanism BRS11C
Access Inner & Outer disc operation.
Note: Refer to Section 8.3 Fig 3. for
process flow .
The counter will
increment by one .
When reach 9999
will change to 0000
Cancellation Display
BRS11C Reliability
(Combination)
In this mode,ensure the CD is in the
main unit.
To determine CD Mechanism Unit
(BRS11C) Open/Close & Access Inner &
Outer Disc Operation.
In this mode,ensure the CD is in the
main unit.
In Doctor Mode :
1. Press [10] [2] [1] button
on remote control.
2. To cancel, press [0]
on remote control.
In Doctor Mode :
1. Press [10] [1] [2] button
on remote control.
2. To cancel, press [0]
on remote control.
2. To cancel, press [0 ]
on remote control.
In Doctor Mode :
1. Press [10] [1] [5] button
on remote control.
2. To cancel, press [0]
on remote control.

20
8.2.3. Doctor Mode Table 3
FL Display
Key Operation
Front Key
Item
Description
Mode Name
CD
Self- Adjustment
(AJST)
Result Display
i. Function: To display result of
self-adjustment for CD .
This is used for servicing
and analysis.
CD LSI
Ve rsion Check
For checking CD LSI Version and
checksum information.
In Doctor Mode:
1. Press [10] [1] [4] button
on remote control .
In Doctor Mode :
1. Press [4] button
on remote control .
Display of auto
adjustment result
Reference table:
ERROR Code
Status
Condition
012468 ACEF
AOC1/AOC2 O O O O OOOO -
ABC2/ABC1 O - X O X O X O X -
2
nd
AOC1 O - O X X O O X X -
FAGC/T AGC O - O O O X X X X -
AGC2 O - OOOOOO O
O: OK ;
X: NG (In case that time out happens.)
: Either one of FO AOC, TR AOC and
FO coarse AGC is NG .
: If the AGC is NG (ignore others).
2.To cancel, press [0]
on remote control .
2.To cancel, press [0]
on remote control .
ROM Version
(Display 1)
(Display 2)
Year
Develop
Year
Develop
ROM
Type
Version (Decimal)
after
2 sec
Version (Decimal ) C hecksum (Hex)