Panasonic SA-AKX600LM User manual

© Panasonic Corporation 2015. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
PMX1506006CE
CD Stereo System
Model No. SA-AKX600LM
SA-AKX800LM
Product Color: (K)...Black Type
TABLE OF CONTENTS
1 Safety Precautions
1.1. General Guidelines
1.2. Before Repair and Adjustment
1.3. Protection Circuitry
1.4. Power Supply using SMPS Module
1.5. Safety Parts Information
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices
2.2. Precaution of Laser Diode
2.3. General description about Lead Free Solder
(PbF)
2.4. Handling Precautions for Traverse Unit
2.5.Grounding for electrostatic breakdown
prevention
3 Service Navigation
3.1. Service Information
4 Specifications
5 Location of Controls and Components
5.1. Remote Control Key Button Operation
5.2. Main Unit Key Button Operation
6 Service Mode
6.1. Cold-Start
6.2. Sales Demonstration Lock Function
6.3. Doctor Mode Table
6.4. Self-Diagnostic Mode
6.5. Self-Diagnostic Error Code Table
7 Troubleshooting Guide
8 Disassembly and Assembly Instructions
8.1. Types of Screws
8.2. Disassembly Flow Chart
8.3. Main Components and P.C.B. Locations
8.4. Disassembly of Top Cabinet
8.5. Disassembly of Front Panel Unit
Please refer to the original service manual for:
CD Mechanism Unit (BRS12C) , Order No. PSG1303059AE
Speaker system SB-AKX800LM, SB-AKW800LM Order No. PMX1506007CE

2
8.6. Disassembly of Panel P.C.B.
8.7. Disassembly of USB P.C.B.
8.8. Disassembly of Music Port P.C.B.
8.9. Disassembly of Rear Panel
8.10. Disassembly of Main P.C.B.
8.11. Disassembly of SMPS Module
8.12. Disassembly of Tuner P.C.B.
8.13. Disassembly of CD Mechanism Unit
8.14.Disassembly of CD Interface P.C.B.
9 Service Position
9.1. Checking of Panel P.C.B.
9.2. Checking of Main P.C.B. and SMPS Module
10 Block Diagram
10.1. System Control
10.2. Audio
10.3. Power Supply
11 Wiring Connection Diagram
12 Schematic Diagram
12.1. Schematic Diagram Notes
12.2. Main (CD Motor Driver) Circuit
12.3. Main (USB EMMC) Circuit
12.4. Main (SOC IO Expander) Circuit (1/2)
12.5. Main (SOC IO Expander) Circuit (2/2)
12.6. Main (Damp) Circuit (1/2)
12.7. Main (Damp) Circuit (2/2)
12.8. Main (Connector) Circuit
12.9. Main (DSP) Circuit
12.10. Main (VREG Fan) Circuit (1/2)
12.11. Main (VREG Fan) Circuit (2/2)
12.12. Tuner Circuit
12.13. Panel Circuit
12.14. USB, CD Interface and Music Port Circuit
13 Printed Circuit Board
13.1. Main P.C.B. (Side A)
13.2. Main P.C.B. (Side B)
13.3. Tuner and CD Interface P.C.B.
13.4. Panel, USB and Music Port P.C.B.
14 Voltage and Waveform Measurement
14.1. Voltage Measurement
14.2. Waveform Chart
15 Exploded View and Replacement Parts List
15.1. Cabinet Parts Location 1
15.2. Cabinet Parts Location 2
15.3. Packaging (For SC-AKX600LM)
15.4. Packaging (For SC-AKX800LM)
15.5. Mechanical Replacement Part List
15.6. Electrical Replacement Parts List

3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by in the
Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts
should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify
the original design without permission of manufacturer.
2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal
injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during
servicing.
3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be
1.1.2. Leakage Current Hot Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15μF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1-1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent)
may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the
limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is
returned to the customer.
Figure 1-1

4
1.2. Before Repair and Adjustment
Disconnect AC power to discharge AC capacitor (in SMPS Module) as indicate below diagram through a 10 Ω, 10 W resistor to
ground.
Figure 1-2
Caution:
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac to avoid overcurrent.
Current consumption at AC 127 V, 60 Hz in Power ON, FM Tuner at volume minimal mode should be ~ 750 mA (LM).
1.3. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
•No sound is heard when the power is turned on.
•Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.

5
1.4. Power Supply using SMPS Module
This model uses Switching Mode Power Supply (SMPS Module) to provide the power supply to the unit. Here is the supplied part
no. for the Module
1) N0AB2GP00003
Figure 1-3

6
1.5. Safety Parts Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams, Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.
Model: SC-AKX600LM
Safety
K2CB2CB00022
RKM0765-KL
RKM0765Z-K
RD-DDL112-PX
RQT0A34-1M
N0AB2GP00003
CD UNIT
RGR0473B-G
Part No.
SWITCHING POWER
SUPPLIES(AC-DC CONVERTER
TOP CABINET (BEND)
TOP CABINET (UNBENT)
AC CORD.
O/I BOOK (SP)
Part Name
REAR PANEL
Model: SC-AKX800LM
Safety
K2CB2CB00022
RKM0765-KL
RKM0765Z-K
RD-DDL112-PX
RQT0A34-1M
N0AB2GP00003
CD UNIT
RGR0473C-D
Part No.
SWITCHING POWER
SUPPLIES(AC-DC CONVERTER
TOP CABINET (BEND)
TOP CABINET (UNBENT)
AC CORD.
O/I BOOK (SP)
Part Name
REAR PANEL

7
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi-
tive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. Precaution of Laser Diode
Caution:
This product utilizes a laser diode with the unit turned “on”, invisible laser radiation is emitted from the pickup lens.
Wavelength: 790 nm (CD)
Maximum output radiation power from pickup: 100 μW/VDE
Laser radiation from the pickup unit is safety level, but be sure the followings:
1. Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pickup unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pickup lens for a long time.

8
2.3. Generaldescription about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
•The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
•To put lead free solder, it should be well molten and mixed with the original lead free solder.
•Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
•Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
•Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
•The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
2.4. Handling Precautions for Traverse Unit
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the traverse unit.
2.4.1. Cautions to Be Taken in Handling the Optical Pickup Unit
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed
should be short-circuited with a short pin or a clip.
3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4. The antistatic FFC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexi-
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)

9
ble cable, cut off the antistatic FFC.
Figure 2-1
2.5. Grounding for electrostatic breakdown prevention
•As for parts that use optical pick-up (laser diode), the optical pick-up is destroyed by the static electricity of the working environ-
ment.
Repair in the working environment that is grounded.
2.5.1. Worktable grounding
•Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed and ground the sheet.
2.5.2. Human body grounding
•Use the anti-static wrist strap to discharge the static electricity form your body (Figure 2-2).
Figure 2-2

10
3 Service Navigation
3.1. Service Information
This service manual contains technical information which will allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
3.1.1. Software Update Procedure
UPDATE PROCEDURE
Perform the following steps.
ƔStep 1: Preparing USB devic
e
ƔStep 2: Software Update
Step 1: Preparing USB device
Before start creating the update USB, it is nessesary to check the update file.
It is important to use the correct file otherwise USB version up process will not
working.
Note: Please do not rename the file as the updating process will look for above naming. If different
name, version up process will not work.
To create USB update, copy the desired FRM file (depends on model) into USB device.
Please make sure there is no other files inside the USB device.
Step 2: Software Update
<Caution>
ŹDuring the update process, do not disconnect the AC power supply cord.
ŹDo not press any buttons, except as instructed. Failure to do so may result in the set
becoming unresponsive which will require repair.
Step:
ŹSet need to be turn ON in order to support USB update process.
ŹGo to USB selector until the display show "NODEVICE".
1. Insert USB device (With FRM file inside)
2. During the update process, the below message will shown on the display.
3. When "SUCCESS" display appear, unplug USB then ac out supply. Firmware updation process
completed.
Thisistheprecentageof
theupdateprocess.It
willstartwith0%until
99%

11
4 Specifications
Amplifier section
RMS output power stereo mode
Front Hi
340 W per channel (3 Ω),1 kHz, 30% THD (for AKX600)
295 W per channel (3 Ω),1 kHz, 30% THD (for AKX800)
Front Lo
460 W per channel (2 Ω),100Hz, 30% THD (for AKX600)
470 W per channel (2 Ω),100Hz, 30% THD (for AKX800)
Subwoofer Ch
470 W per channel (2 Ω),100Hz, 30% THD (for AKX800)
Total RMS stereo mode power
2000 W (for AKX800)
Tuner, terminals section
Preset memory FM 30 stations
AM 15 stations
Frequency modulation (FM)
egnarycneuqerF
(100 kHz step)
87.9 MHz to 107.9 MHz (200 kHz step)
57slanimretannetnA Ω(unbalanced)
Amplitude modulation (AM)
egnarycneuqerF (10 kHz step)
AUX 1
)metsys1(kcajniPtupnioiduA
AUX 2
k7.4,Vm001ytivitisneS Ω
Disc section
Discs played (8 cm or 12 cm) CD, CD-R/RW (CD-DA, MP3*)
* MPEG-1 Layer 3
Pick up
)DC(mn097htgnelevaW
USB section
USB Port
deepslluf0.2BSUdradnatsBSU
)3pm.*(3PMtroppustamrofelifaideM
USB device file system FAT12, FAT16, FAT32
USB recording
spbk821etartiB
)ylnoDC(x3,x1deepsgnidrocerBSU
)3pm.*(3PMtamrofelifgnidroceR
Internal memory section
Memory
BG2ezisyromeM
)3pm.*(3PMtroppustamrofelifaideM
Memory recording
spbk821etartiB
Memory recording s )ylnoDC(x3,x1deep
)3pM.*(3PMtamrofelifgnidroceR
Bluetooth®section
General
Power supplyAC 127 V, 60 Hz
Power consumption 173 W
Dimensions (W x H x D) 348 mm x 192 mm x 303 mm
Weight 3.6 kg
Operating temperature range 0°C to +40 °C
Operating humidity range 35% to 80% RH
(no condensation)
Power Consumption in
standby mode
Power Consumption in standby
mode
(With "BLUETOOTH STANDBY" set
to "ON")
9.2 Wh/day (approximate)
Note:
1. Specifications are subject to change without notice.
Weight and dimension are approximate
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
PMPO Output Power17600 W (for AKX600)
22000 W (for AKX800)
zHM0.801otzHM5.78
zHk0171otzHk025
USB port power Max 500mA
Version Bluetooth®Ver.2.1 + EDR
Class Class 2
Supported profiles
A2DP, AVRCP, SPP, OPP, FTP
Operating frequency 2.4 GHz band, FH-SS
Operating distance 10 m line of sight
Speaker section
Speaker unit(s)
Impedance High 3 / Low 2
Output sound presure 87dB/W(1m)
Frequency range 42Hz a 28 kHz (-16 dB)
46Hz a 23 kHz (-10 dB)
Woofer 8 cm cone type
Super Woofer 20 cm cone type
Type 3 way, 3 speaker system
For SB-AKX800
Tweeter 6 cm cone type
Weight 7.1 kg
Ω Ω
Dimensions (W x H x D) 300 mm x 401 mm x 292 mm
Speaker unit(s)
Impedance 2
Output sound presure 88dB/W(1m)
Frequency range 42Hz a 250 Hz (-16 dB)
44Hz a 200 Hz (-10 dB)
Super Woofer 25 cm cone type
Type 1 way, 1 speaker system
For SB-AKW800
Weight 8.3 kg
Ω
Dimensions (W x H x D) 360 mm x 401 mm x 271 mm
Power Consumption in
normal mode
173 Wh/day (considering 1 hour
use per day)
6.9 Wh/day (considering 23 hours
a day standby)
1600 W (for AKX600)

12
5 Location of Controls and Components
5.1. Remote Control Key Button Operation

13
5.2. Main Unit Key Button Operation

14
6 Service Mode
6.1. Cold-Start
6.2. Sales Demonstration Lock Function
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Cold Start To carry out cold-start or initialize
to shipping mode
1. Unplug AC power cord.
2. Press & hold [POWER]
button.
3. Plug in AC power cord
while [POWER] button
being pressed.
4. Release [POWER] button.
Entering into
Sales
Demonstration
Lock Mode
To enter into sales demonstration
lock mode.
1. Turn on the unit.
2. Select to any mode
function.
3. Press and hold
[;OPEN/CLOSE] and
[CD/RADIO/AUX] keys for
5 sec or more.
The display will show upon
entering into this mode for
2 sec.
Note: [;OPEN/CLOSE]
button is invalid and the main
unit displays "LOCKED" while
the lock function mode is
entered.
Cancellation of
Sales
Demonstration
Lock Mode
To cancel sales demonstration
lock mode.
1. Turn on the unit.
2. Select to CD mode function.
3. Set volume to Vol 19.
4. Press and hold
[;OPEN/CLOSE] and
[CD/RADIO/AUX] keys for
5 sec or more.
The display will show upon
entering into this mode for
2 sec.
FL Display
Key Operation
Front Key
Item
DescriptionMode Name

15
6.3. Doctor Mode Table
6.3.1. Doctor Mode Table 1
FL Display Key Operation
Front Key
Item
DescriptionMode Name
Doctor Mode
EEPROM
checksum
check (Display 1) (For AKX600)
(Decimal)
1 2 3 4
To enter into Doctor Mode In CD Mode:
1. Press [ ] button on
main unit follow by [4]
and [7] on remote control.
In CD mode:
1. Enter into Doctor Mode
2. To exit, press [DELETE]
button on remote control or,
press [POWER, /I] button
on Main Unit
Displaying of
1. Year Develop.
2. Model Type.
3. ROM Type.
4. Firmware Version.
(Display 2) (For AKX800)
Cold Start To active cold start upon next AC
power up when reset start is
execute the next time.
In Doctor Mode:
1. Press [4] button on the
remote control.
Version No. (001 ~ 999) specific for each
firmware
(Decimal)1 2 3 4

16
6.3.2. Doctor Mode Table 2
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Volume Setting
Check
FL Display Check
To check volume setting of the main
unit.
To check FL segment display.
All segments will light up while all LED
blink at 0.5s intervals.
In Doctor Mode:
1. Press [7], [8], [9] button on
the remote control.
In Doctor mode:
1. Press [1] button on the
remote control.
2. To cancel this mode, press
[0] button on the remote
control.
Press [7]: VOL50
Press [8]: VOL35
Press [9]: VOL0
Volume
In this mode, the tray will open & close
automatically.
Cancellation Display
Loading Test To determine open & close
operation of the CD Mechanism Unit.
The counter will
increment by one.
When reach 99999999
will change to 00000000
Cancellation Display
Traverse Test To determine traverse unit
operation for inner & outer access track.
The counter will
increment by one.
When reach 99999999
will change to 00000000
The counter will
increment by one.
When reach 99999999
will change to 00000000
Cancellation Display
Reliability Test
(Combination)
In this mode, ensure the CD is in the
main unit.
To determine traverse unit
operation & open/close operation of the
mechanism.
In this mode, ensure the CD is in the
main unit.
In Doctor Mode:
1. Press [10] [2] [1] button
on the remote control.
In Doctor Mode:
2. To cancel this mode, press
[0] button on the remote
control.
2. To cancel this mode, press
[0] button on the remote
control.
2. To cancel this mode, press
[0] button on the remote
control.
1. Press [10] [1] [2] button
on the remote control.
In Doctor Mode:
1. Press [10] [1] [5] button
on the remote control.

17
6.4. Self-Diagnostic Mode
6.5. Self-Diagnostic Error Code Table
Self-Diagnostic Function provides information on any problems occurring for the unit and its respective components by displaying
the error codes. These error code such as U**, H** and F** are stored in memory and held unless it is cleared.
The error code is automatically display after entering into self-diagnostic mode.
6.5.1. Power Supply Error Code Table
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Self Diagnostic
Mode
To enter into self diagnostic checking Step 1: Select CD mode
(Ensure no disc is inserted).
To exit, press [8] on main unit or
remote control.
Step 2: Press & hold [g] button
follow by [y/i] on
main unit for 2 seconds.
Error Code
Information
System will perform a check on
any unusual/error code from the
memory
Example: Step 1: In self diagnostic mode,
Press [g] on main unit.
To exit, press [8] on main unit or
remote control.
Delete error code To clear the stored in memory
(EEPROM IC)
Step 1: In self diagnostic mode,
Press [0] on remote control.
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Error Code F61 Diagnosis Contents:
Power Amp IC output abnormal.
Upon power on, PCONT=HIGH,
DC_DET_AMP after checking LSI.
Error Code F76 Diagnosis Contents:
Power Amp IC output abnormal.
DC_DET_PWR.
Error Code
F61-76
Diagnosis Contents:
Power Amp IC output abnormal.
Both DCDET (NG).
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.

18
6.5.2. CD Mechanism Error Code Table
6.5.3. Bluetooth Error Code Table
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Error Code
CD H15
Diagnosis Contents:
CD Open Abnormal.
During operation POS_SW_R On
fail to be detected within 4 sec.
Error No. shall be clear by force
or during cold start.
Error Code
CD H16
Diagnosis Contents:
CD Closing Abnormal.
During operation POS_SW_CEN
On fail to be detected within 4 sec.
Error No. shall be clear by force
or during cold start.
Error Code
F26
Diagnosis Contents:
Communication between CD
servo LSI and micro-p abnormal.
During switch to CD function, if
SENSE = “L” within fail safe time
of 20ms.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.
FL Display
Key Operation
Front Key
Item
DescriptionMode Name
Error Code F70 Diagnosis Contents:
Bluetooth Communication.
Communication between
Bluetooth module and micro-p
abnormal.
Error Code F77 Diagnosis Contents:
Bluetooth Address Error
If there is no valid Bluetooth
address stored in the
EEPROM IC.
Press [g] on main unit for next
error.
Press [g] on main unit for next
error.

19
7 Troubleshooting Guide
“Contents for this section is not available at time of issue”

20
8 Disassembly and Assembly Instructions
•Illustration is based on SA-AKX800LM.
Caution Note:
•This section describes the disassembly and/or assembly procedures for all major printed circuit boards & main compo-
nents for the unit. (You may refer to the section of “Main components and P.C.B Locations” as described in the service
manual)
•Before carrying out the disassembly process, please ensure all the safety precautions & procedures are followed.
•During the disassembly and/or assembly process, please handle with care as there may be chassis components with
sharp edges.
•Avoid touching heatsinks due to its high temperature after prolong use. (See caution as described below)
•During disassembly and assembly, please ensure proper service tools, equipments or jigs is being used.
•During replacement of component parts, please refer to the section of “Replacement Parts List” as described in the ser-
vice manual.
•Select items from the following indexes when disassembly or replacement are required.
•Disassembly of Top Cabinet
•Disassembly of Front Panel Unit
•Disassembly of Panel P.C.B.
•Disassembly of USB P.C.B.
•Disassembly of Music Port P.C.B.
•Disassembly of Rear Panel
•Disassembly of Main P.C.B.
•Disassembly of SMPS Module
•Disassembly of Tuner P.C.B.
•Disassembly of CD Mechanism Unit
•Disassembly of CD Interface P.C.B.
8.1. Types of Screws
RHD30007-K2J
RHD30119-S
RHD26046
RHD30111-31
RHDX30005-J
RHDX031008