Panasonic SA-AK570PL Building instructions

■AMPLIFIER SECTION
RMS output power
Front CH (both channels driven)
250 W per channel (6 Ω), 1 kHz, 10% THD
Total RMS stereo mode power 500 W
PMPO 5500 W
■FM/AM TUNER, TERMINALS SECTION
Preset station FM 30 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range
87.9 to 107.9 MHz (200 kHz steps) (PL only)
87.5 to 108.00 MHz (100 kHz steps) (PL only)
87.50to108.00MHz(50kHzsteps)(GCPonly)
Antenna terminal(s) 75 Ω(unbalanced)
Amplitude Modulation (AM)
Frequency range
520 to 1710kHz (10 kHz steps) (PL only)
522 to 1629 kHz (9 kHz step) (GCP only)
522to1630kHz(10kHzsteps)(GCPonly)
Music Port (front) jack
© 2008 Matsushita Electric Industrial Co. Ltd.. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
SA-AK570PL
SA-AK570GCP
Colour
(K)... Black Type
Sensitivity 100 mV, 4.0 k Ω
Terminal Stereo, 3.5 mm jack
Headphone jack
Terminal Stereo, 3.5 mm jack
Output level (CD, 1 kHz, -20 dB) 32 Ω(Max)
Mic jack
Sensitivity 0.7 mV, 1.2 k Ω
Terminal Mono, 3.5 mm jack (1 system)
■CASSETTE DECK SECTION
Type 1way
Track system 4 track, 2 channel
Heads
Record/playback Solid permalloy head
Erasure Double gap ferrite head
Motor DC servo motor
Recording system AC bias 100 kHz
Erase system AC erase 100 kHz
Tape speed 4.8 cm/s
Overall frequency response (+3, -6 dB) at DECK OUT
NORMAL 35 Hz to 10 kHz
S/N ratio 50 dB (A weighted)
CD Stereo System
Notes: This model’s CD mechanism changer unit is CR14C. Please refer to the original Service Manual
(Order No. MD0805031CE) for this mechanism.
Specifications
ORDER NO. MD0805003CE

Wow and flutter 0.18 % (WRMS)
Fast forward and rewind time
Approx. 120 seconds with C-60 cassette tape
■DISC SECTION
Disc played [8 cm or 12 cm]
(1) CD-Audio (CD-DA)
(2) CD-R/RW (CD-DA, MP3* formatted disc)
(3) MP3*
* MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength 780 nm
Beam Source Semiconductor laser
Audio output (Disc)
Number of channel 2(FL,FR)
FL = Front left channel
FR = Front right channel
■USB SECTION
USB Port
USB Standard USB 2.0 full speed
Media file format support
MP3 (*.mp3)
USB device file system
FAT 12
FAT 16
FAT 32
USB port power 500 mA (Max)
USB Ripping (recording)
Recording file format
1 Safety Precautions 3
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 5
3 Handling Precautions for Traverse Unit 6
4 Precaution of Laser Diode 8
5 About Lead Free Solder (PbF) 9
6 Operation Procedures 10
7 Self diagnosis and special mode setting 14
8 Assembling and Disassembling 22
9 Disassembly and Assembly of Traverse Unit Assembly in
Play Position 56
10 Service Fixture and Tools 58
11 Service Positions 58
MP3 (*.mp3)
Bit rate 128 kbps / 192 kbps / 320 kbps
USB recording speed 1x, max 4x (CD only)
■GENERAL
Power supply
AC 120 V, 60Hz (PL only)
AC 110 to 127/220 to 240 V, 50/60 Hz (GCP only)
Power consumption 141W(PLOnly)
124 W (GCP Only)
Dimensions (WxHxD) 250x331x334 mm
Mass 4.9 kg
Operating temperature range 0 to 40°C
Operating humidity range 35 to 80% RH (no condensation)
Power consumption in standby mode:
0.3 W (approx.) (PL only)
0.5 W (approx.) (GCP only)
■SYSTEM
SC-AK570 (PL) Music center: SA-AK570 (PL)
Speaker: SB-AK570 (PL)
SC-AK570 (GCP) Music center: SA-AK570 (GCP)
Speaker: SB-AK570 (PL)
For information on speaker system, please refer to the original
Service Manual (Order No. MD0805011CE) for SB-AK570PL-K.
Notes:
1.Specifications are subject to change without notice. Mass and
dimensions are approximate.
2.Total harmonic distortion is measured by the digital spectrum
analyzer.
12 Procedure for Checking Operation of Individual Parts of Deck
Mechanism Unit 65
13 Measurement And Adjustments 66
14 Voltage Measurement and Waveform Chart 68
15 Wiring Connection Diagram 75
16 Block Diagram 77
17 Notes Of Schematic Diagram 85
18 Schematic Diagram 87
19 Printed Circuit Board 105
20 Illustration of ICs, Transistors and Diodes 113
21 Terminal Function of Integrated Circuits 114
22 Exploded Views 117
23 Replacement Parts List 121
CONTENTS
Page Page
2
S
A-AK570PL
/S
A-AK570
GC
P

1 Safety Precautions
1.1. General Guidelines
1.When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2.After servicing, ensure that all the protective devices such as insulation barriers and insulation papers shields are properly
installed.
3.After servicing, check for leakage current checks to prevent from being exposed to shock hazards.
(This “Safety Precaution” is applied only in U.S.A.) (For PL Only)
1.Before servicing, unplug the power cord to prevent an electric shock.
2.When replacing parts, use only manufacturer’s recommended components for safety.
3.Check the condition of the power cord. Replace if wear or damage is evident.
4.After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5.Before returning the serviced equipment to the customer, be sure to make the following insulation resistance test to prevent the
customer from being exposed to a shock hazard.
1.1.1. Leakage Current Cold Check
1.Unplug the AC cord and connect a jumper between the two prongs on the plug.
2.Using an ohmmeter measure the resistance value, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be .
1.1.2. Leakage Current Hot Check (See Figure 1)
1.Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2.Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitor, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3.Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4.Check each exposed metallic part, and measure the voltage at each point.
5.Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6.The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may
be used to make the hot checks, leakage current must not exceed 1/2 milliamp. Should the measurement is out of the limits
specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to
the customer.
Fig. 1
1.2. Before Use (For GCP Only)
Be sure to disconnect the mains cord before adjusting the voltage selector.
Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will
be used. (If the power supply in your area is 110V or 127V, set to the “127V” position.)
Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries,
the correct voltage is already set.)
3
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

1.3. Before repair and adjustment
Disconnect AC power, discharge AC Capacitors C5700, C5701, C5703, C5704, C5705 (PL Only); C5700, C5701, C5703, C5704,
C5705, C5706 and C5707 (GCP Only) through a 10Ω, 5W resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
Current consumption at AC 120V, 60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~ 500mA (For PL only).
Current consumption at AC 110V~127V, 50/60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~ 750mA (For GCP
only).
Current consumption at AC 220V~240V, 50/60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~ 500mA (For GCP
only).
1.4. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1.Turn off the power.
2.Determine the cause of the problem and correct it.
3.Turn on the power once again after one minute.
Note :
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.5. Safety Part Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams & Replacement Parts List. It is essential that these critical parts should
be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without
permission of manufacturer.
Table 1
Reference No. Part No. Part name & Description Remarks
18 RGRX0070D-A REAR PANEL [M] PL
18 RGRX0070E-A REAR PANEL [M] GCP
36 RKMX0144-K TOP CABINET [M]
51 RMZ0339 ZNR COVER [M] GCP
68 REXX0686 VOLTAGE SELECTOR WIRE 1 [M] GCP
69 REXX0687 VOLTAGE SELECTOR WIRE 2 [M] GCP
74 RMVX0119 BARRIER COVER [M] PL
81 REZX0024 PRIMARY WIRE 2 [M] GCP
82 REZX0023 PRIMARY WIRE 1 [M] GCP
340 RAEX0190A-V TRAVERSE ASSEMBLY UNIT [M] (RTL)
A2 K2CB2CB00018 AC CORD [M] PL
A2 K2CQ2CA00007 AC CORD [M] GCP
PCB4 REPX0676D SMPS P.C.B. [M] (RTL) PL
REPX0676E SMPS P.C.B. [M] (RTL) GCP
PCB10 REPX0676D AC INLET P.C.B. [M] (RTL) PL
REPX0676E AC INLET P.C.B. [M] (RTL) GCP
PCB13 REPX0676E VOLTAGE SELECTOR P.C.B. [M] (RTL) GCP
DZ5701 ERZV10V511CS DIODE [M]
S5701 K0ABCA000007 SW VOLTAGE SELECTOR [M] GCP
L5702 ELF22V035B LINE FILTER [M]
T2900 G4D1A0000117 SWITCHING TRANSFORMER [M]
T5701 ETS48AB116AC TRANSFORMER [M] GCP
T5701 ETS48AB12GAC SWITCHING TRANSFORMER [M] PL
T5751 ETS19AB256AG BACKUP SW TRANFORMER [M]
4
SA
-
AK
570
PL / SA
-
AK
570
GCP

Reference No. Part No. Part name & Description Remarks
PC5701 B3PBA0000402 PHOTO COUPLER [M]
PC5702 B3PBA0000402 PHOTO COUPLER [M]
PC5720 B3PBA0000402 PHOTO COUPLER [M]
PC5799 B3PBA0000402 PHOTO COUPLER [M]
F1 K5D802APA008 FUSE [M] PL
F1 K5D802BNA005 FUSE [M] GCP
FP2901 K5G4013A0001 FUSE PROTECTOR [M]
TH5701 D4CAA5R10001 THERMISTOR [M] PL
TH5702 D4CAC8R00002 THERMISTOR [M] GCP
TH5860 D4CC11040013 THERMISTOR [M]
P5701 K2AA2B000017 AC INLET/OUTLET [M] GCP
P5701 K2AB2B000010 AC INLET/OUTLET [M] PL
C5700 F1BAF1020020 1000pF [M]
C5701 F0CAF334A087 0.33uF [M]
C5703 F0C2H1040001 0.1uF 500V [M] GCP
C5703 F0CAF224A085 0.22uF [M] PL
C5704 F1BAF1020020 1000pF [M]
C5705 F1BAF1020020 1000pF [M] GCP
C5706 F1BAF1020020 1000pF [M] GCP
C5707 F1BAF1020020 1000pF [M]
C5711 F2B2G471A083 470uF 400V [M] GCP
C5712 F2B2D8210010 820uF 200V [M] PL
C5712 F2B2G471A083 470uF 400V [M] GCP
C5713 F0C2J1030005 0.01uF 630V [M]
2 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1.Immediately before handling any semiconductor component or semiconductor-equiped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2.After removing an electrical assembly equiped with ES devices, place the assembly on a conductive surface such as aluminium
foil, to prevent electrostatic charge build up or exposure of the assembly.
3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4.Use only an anti-static solder remover device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge to damage ES devices.
5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or
comparable conductive material).
7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8.Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
5
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

3 Handling Precautions for Traverse Unit
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the traverse unit.
3.1. Cautions to Be Taken in Handling the Optical Pickup Unit
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1.Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2.To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed should
be short-circuited with a short pin or a clip.
3.The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4.The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexible
cable, cut off the antistatic FPC.
3.2. Grounding for electrostatic breakdown prevention
Some devices such as the CD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electricity
in the working environment. Proceed servicing works under the working environment where grounding works is completed.
3.2.1. Worktable grounding
1.Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.
3.2.2. Human body grounding
1.Use the anti-static wrist strap to discharge the static electricity form your body.
6
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

7
S
A-AK570PL
/S
A-AK570
GCP

4 Precaution of Laser Diode
CAUTION :
This product utilizes a laser diode with the unit turned "on", invisible laser radiation is emitted from the pickup lens.
Wavelength: 785 nm (CD) / 655 nm (DVD)
Maximum output radiation power from pickup: 100 µW/VDE
Laser radiation from the pickup unit is safety level, but be sure the followings:
1.Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous.
2.Do not adjust the variable resistor on the pickup unit. It was already adjusted.
3.Do not look at the focus lens using optical instruments.
4.Recommend not to look at pickup lens for a long time.
8
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

5 About Lead Free Solder (PbF)
5.1. Service caution based on legal restrictions
5.1.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt
the lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30
degrees C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: Tin (Sn), 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
9
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

6 Operation Procedures
6.1. Main Unit Key Buttons Operations
10
S
A-AK570PL
/S
A-AK570
GC
P

6.2. Remote Control Key Buttons Operations
11
SA
-
AK
570
PL / SA
-
AK
570
GCP

6.3. Using the Music Port
This feature enables you to enjoy music from a portable audio equipment.
12
SA
-
AK
570
PL / SA
-
AK
570
GCP

6.4. Connecting and Playing a USB Mass Storage Class Device
13
SA
-
AK
570
PL / SA
-
AK
570
GCP

7 Self diagnosis and special mode setting
This unit is equipped with features of self-diagnostic & special mode setting for checking the functions & reliability.
Special Note : Checking of the reliability (ageing) & changer operation must be carry out to ensure good working condition
in unit.
7.1. Service Mode Summary Table
The service modes can be activated by pressing various button combination on the main unit and remote control unit.Below is the
summary for the various modes for checking:
Player buttons Remote control unit buttons Application Note
[STOP] [4], [7] Entering into doctor mode (Refer to section .7.2.1. service mode
Table 1 for more information.)
[STOP] [ ] Entering into service mode (Refer to section .7.2.1. service mode
Table 1 for more information.)
Mode Remote control unit buttons Application Note
In Doctor Mode [1] FL all segment & LED inspection (Refer to section .7.2.2. service mode
Table 2 for more information.)
[MUSIC.P] Tuner Check (Refer to section .7.2.2. service mode
Table 2 for more information.)
[7] Volume 50 setting check (Refer to section .7.2.2. service mode
Table 2 for more information.)
[8] Volume 35 setting check (Refer to section .7.2.2. service mode
Table 2 for more information.)
[9] Volume 0 setting check (Refer to section .7.2.2. service mode
Table 2 for more information.)
[2] Micro-P Version Display (Refer to section .7.2.2. service mode
Table 2 for more information.)
[4] CD→USB Recording & Playing inspection (Refer to section .7.2.2. service mode
Table 2 for more information.)
[5] CD-MP3 Reading & Playing inspection (Refer to section .7.2.2. service mode
Table 2 for more information.)
[], [1], [1] CD Loading Test Mode (Refer to section .7.2.2. service mode
Table 2 for more information.)
[], [1], [2] CD Traverse Unit Test Mode (Refer to section .7.2.2. service mode
Table 2 for more information.)
[], [1], [3] CD Combination Test Mode (Refer to section .7.2.2. service mode
Table 2 for more information.)
Mode Remote control unit buttons Application Note
In Service Mode [1] self diagnostic history (Refer to section .7.2.3. service mode
Table 3 for more information.)
[2] Micro-P FW (Refer to section .7.2.3. service mode
Table 3 for more information.)
[3] Cold Start (Reset) (Refer to section .7.2.3. service mode
Table 3 for more information.)
7.2. Service Mode Table
Below is the various special modes for checking:-
7.2.1. Service Mode Table 1
Item FL Display Key Operation
Mode Name Description Front Key
Doctor Mode To enter into Doctor
Mode. In any mode:
1.Press [ ] button on main unit
follow by [4] and [7] on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
Service Mode To enter into Service
Mode. 1.Select [CD] for DISC mode (Ensure no disc is inserted).
2.Press and hold [ ]button on
main unit for 2 seconds follow by
[] on remote control.
To exit, press [ ] button on main unit or
remote control.
14
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

7.2.2. Service Mode Table 2
Item FL Display Key Operation
Mode Name Description Front Key
FL Display Test To check the FL
segments display (All
segments will light up)
In doctor mode:
1.Press [1] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
Tuner Check To Inspect Tuner Check In doctor mode:
1.Press [MUSIC.P] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
Volume Setting
Mode To check for the volume setting of the main unit.
The volume will be
automatically set to its
respective level (in dB).
During this mode,
treble/bass/EQ will be set
to ‘0’dB & OFF.
Display 1 In doctor mode:
1. Press [7] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
Display 1 In doctor mode:
2. Press [8] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
Display 1 In doctor mode:
3. Press [9] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
Micro-P Version
Display Checking of various items and firmware
version.
Note: The micro-
processor version as
shown is an example. It
will be revise when there
is an updates.
In doctor mode:
1.Press [2] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
CD→USB
Recording &
Playing inspection
To check for the
CD→USB Recording
setting of the main unit.
The volume will be
automatically set to its
respective level (in dB).
During this mode,
treble/bass/EQ will be set
to ‘0’dB & OFF.
In doctor mode:
1.Press [4] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
15
SA
-
AK
57
0PL / SA
-
AK
57
0GCP

Item FL Display Key Operation
Mode Name Description Front Key
CD-MP3 Reading
& Playing
inspection
To check for the CD-MP3
Reading setting of the
main unit. The volume
will be automatically set
to its respective level (in
dB). During this mode,
treble/bass/EQ will be set
to ‘0’dB & OFF.
(For more information,
refer to section 8.2.4)
In doctor mode:
1.Press [5] button on remote control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
CD Loading Test
Mode To determine the reliability of CD Loading
Unit.
To check for the
open/close operation for
the CD loading unit. It
fails when there is
abnormality in opening or
closing.
In doctor Mode:
1.Press [ ], [1] & [1] button on remote
control.
To cancel, press [PROGRAM] button on remote
control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
CD Traverse Unit
Test Mode To check for the traverse unit operation. In this
mode, the first & lost
track is access & read
(TOC). It fails when TOC
is not completed by IDS
or the traverse is out of
focus.
In doctor Mode:
1.Press [ ], [1] & [2] button on remote
control.
To cancel, press [PROGRAM] button on remote
control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
CD Combination
Test Mode A combination of CD loading & Traverse unit
test.
In doctor Mode:
1.Press [ ], [1] & [3] button on remote
control.
To cancel, press [PROGRAM] button on remote
control.
To exit Doctor Mode, press [ ] button on
main unit or remote control.
7.2.3. Service Mode Table 3
Item FL Display Key Operation
Mode Name Description Front Key
Self Diagnostic
History Checking the records for self-diagnostic. In service mode:
1.Press [1] button on remote control.
To exit Service Mode, press [ ] button on
main unit or remote control.
To clear history, press & hold [0] for 5 seconds
or more.
Micro-P Version
Display Checking of various items and firmware
version.
Note: The micro-
processor version as
shown is an example. It
will be revise when there
is an updates.
FL Display
sequenceDisplay
[]
(Display 1)
(Display 2)
In service mode:
1.Press [2] button on remote control.
To exit Service Mode, press [ ] button on
main unit or remote control.
16
S
A-AK570PL
/S
A-AK570
GC
P

Item FL Display Key Operation
Mode Name Description Front Key
Cold Start (Reset) To activate cold start
ipon next AC power up. In service mode: 1.Press [3] button on remote control.
To exit Service Mode, press [ ] button on
main unit or remote control.
7.3. Reliability Test Mode (CR14C Mechanism)
Below is the process flow chart of ageing for the Mechanism unit (CR14C).
17
S
A-AK570PL
/S
A-AK570
GCP

18
S
A-AK570PL
/S
A-AK570
GC
P

7.4. Error code Table Display
Self-Diagnosis Function (refer Section “7.2.1 Service Mode Table 1”) provides information on any problems occuring for the unit
and its respective components by displaying the error codes. These error code such as U**, H** and F** are stored in memory and
held unless it is cleared.
The error code is automatically display after entering into self-diagnostic mode.
19
SA
-
AK
570
PL / SA
-
AK
570
GCP

7.4.1. Error Code Table (For Deck Mechanism)
Error Code Diagnosis Contents Description of error Automatic FL Display Remarks
H01 Mode SW, plunger
and capstan motor
abnormal
Normal operation during
mecha transition, MODE
SW abnormal is
memorized. The content of
abnormality can be
confirmed in the abnormal
detection mode explained
in the later section.
For deck mechanism unit.
Press [ ] on main unit for
next error.
H02 Rec INH SW
abnormal The content of abnormality can be confirmed in the
abnormal detection mode
explained in the later
section.
For deck mechanism unit.
Press [ ] on main unit for
next error.
H03 HALF SW abnormal For deck mechanism unit.
Press [ ] on main unit for
next error.
F01 Reel pulse abnormal For deck mechanism unit.
Press [ ] on main unit for
next error.
F02 TPS abnormal For deck mechanism unit.
Press [ ] on main unit for
next error.
7.4.2. Error Code Table (For CD Mechanism Unit)
Error Code Diagnosis Contents Description of error Automatic FL Display Remarks
LOAD Load operation faulty The load operation cannot
complete when time out -->
Falsaf reverse operates
again then time out again, it
is memorized.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
UNLD Unload operation
faulty The unload operation cannot complete when time
out --> Falsaf reverse
operates again then time
out again, it is memorized.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
UP Exchange open
operation faulty The exchange open operation cannot complete
when time out --> operation
time out again, it is
memorized.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
DOWN Down operation faulty The down operation cannot
complete when time out -->
Falsaf reverse operates
again then time out again, it
is memorized.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
OPEN Open operation faulty The open operation cannot
complete when time out -->
Falsaf reverse operates
again then time out again, it
is memorized.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
CLOSE Close operation faulty The open operation cannot
complete when time out -->
Falsaf reverse operates
again then time out again, it
is memorized.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
MODEL Mode change to
updown operation
faulty
The mode change to
updown operation cannot
complete when time out
reversing --> operates
again then time out again, it
is memorized. Mode
change to updown.
For CD Mechanism unit (CR14C).
Press [EXCHANGE] on main unit for
next error.
20
SA
-
AK
57
0PL / SA
-
AK
57
0GCP