Panasonic SA-AKX90PH User manual

© Panasonic Corporation 2010. All rights reserved.
Unauthorized copying and distribution is a violation
of law.
PSG1003010CE
CD Stereo System
Model No. SA-AKX90PH
SA-AKX90PR
Product Color: (K)...Black Type
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 4
1.1. General Guidelines---------------------------------------- 4
1.2. Before Use -------------------------------------------------- 4
1.3. Caution For Fuse Replacement------------------------ 4
1.4. Before Repair and Adjustment------------------------- 4
1.5. Protection Circuitry---------------------------------------- 5
1.6. Safety Parts Information----------------------------------5
2Warning--------------------------------------------------------------6
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatic Sensitive (ES) Devices---------------6
2.2. Precaution of Laser Diode-------------------------------7
2.3. Service caution based on Legal restrictions --------8
Notes: Please refer to the original service manual for:
OCD Mechanism Unit (DLS6C),Order No:MD0803034CE
OSpeaker System SB-AKX90PH-K,Order No.:PSG1003001CE

2
2.4. Handling Precautions for Traverse Unit --------------9
3 Service Navigation---------------------------------------------- 11
3.1. Service Information-------------------------------------- 11
4 Specifications----------------------------------------------------12
5 Location of Controls and Components------------------13
5.1. Main Unit Key Button Operation----------------------13
5.2. Remote Control Key Button Operation -------------14
5.3. Media Information----------------------------------------15
6 Self-Diagnostic and Special Mode Setting -------------16
6.1. Cold-Start---------------------------------------------------16
6.2. Doctor Mode Table---------------------------------------17
6.3. Reliability Test Mode (CD Mechanism Unit
(DLS6C)) ---------------------------------------------------19
6.4. Self-Diagnostic Mode -----------------------------------20
6.5. Self-Diagnostic Error Code Table --------------------21
7 Troubleshooting Guide----------------------------------------22
7.1. Troubleshooting Guide for F61 and/or F76)-------22
7.2. Part Location ----------------------------------------------23
7.3. D-Amp IC Operation & Control -----------------------27
8 Service Fixture & Tools ---------------------------------------29
8.1. Service Tools and Equipment-------------------------29
9 Disassembly and Assembly Instructions---------------30
9.1. Disassembly Flow Chart--------------------------------31
9.2. Main Components and P.C.B. Locations-----------32
9.3. Disassembly of Top Cabinet---------------------------33
9.4. Disassembly of Tuner P.C.B.--------------------------34
9.5. Disassembly of Front Panel Assembly -------------34
9.6. Disassembly of Panel P.C.B.--------------------------36
9.7. Disassembly of Remote Sensor P.C.B.-------------37
9.8. Disassembly of CD Open Button P.C.B.------------38
9.9. Disassembly of Jupiter P.C.B.-------------------------39
9.10. Disassembly of Music Port/Headphone P.C.B. ---39
9.11. Disassembly of CD Lid----------------------------------40
9.12. Disassembly of Main P.C.B.---------------------------41
9.13. Replacement of Regulator IC (IC2010)-------------42
9.14. Disassembly of Mic P.C.B.-----------------------------43
9.15. Disassembly of D-Amp P.C.B. ------------------------44
9.16. Disassembly of SMPS P.C.B.-------------------------46
9.17. Replacement of Switching Regulator IC
(IC5701) ----------------------------------------------------47
9.18. Replacement of Rectifier Diode (D5702)-----------48
9.19. Replacement of Regulator Diode (D5801)---------50
9.20. Replacement of Regulator Diode (D5802)---------51
9.21. Replacement of Regulator Diode (D5803)---------52
9.22. Disassembly of CD Mechanism Unit (DLS6C) ---53
9.23. Disassembly of Rear Panel----------------------------55
9.24. Disassembly of Voltage Selector P.C.B.------------56
9.25. Disassembly of CD Servo P.C.B.---------------------57
9.26. Replacement of Audio Digital Amp IC
(IC5000) ----------------------------------------------------58
9.27. Replacement of Audio Digital Amp IC
(IC5400) ----------------------------------------------------59
9.28. Replacement of Audio Digital Amp IC
(IC5200) ----------------------------------------------------60
9.29. Replacement of Audio Digital Amp IC
(IC5300) ----------------------------------------------------61
9.30. Disassembly of Surround D-Amp P.C.B.-----------62
9.31. Replacement of Audio Digital Amp IC
(IC5900) ----------------------------------------------------63
10 Replacement of Traverse Unit ------------------------------65
10.1. Disassembling Procedures ----------------------------65
10.2. Assembling Procedure --------------------------------- 66
11 Service Position------------------------------------------------- 68
11.1. Checking and Repairing of Main P.C.B.------------ 68
11.2. Checking and Repairing of D-Amp P.C.B.--------- 68
11.3. Checking and Repairing of Surround D-Amp
P.C.B.------------------------------------------------------- 68
11.4. Checking and Repairing of Panel P.C.B. ---------- 68
11.5. Checking and Repairing of Jupiter P.C.B.--------- 69
11.6. Checking and Repairing of SMPS P.C.B.---------- 69
12 Voltage & Waveform Chart ---------------------------------- 71
12.1. CD Servo P.C.B. ----------------------------------------- 71
12.2. Main P.C.B. (1/3)----------------------------------------- 72
12.3. Main P.C.B. (2/3)----------------------------------------- 73
12.4. Main P.C.B. (3/3)----------------------------------------- 74
12.5. Jupiter P.C.B. (1/3) -------------------------------------- 75
12.6. Jupiter P.C.B. (2/3) -------------------------------------- 76
12.7. Jupiter P.C.B. (3/3) -------------------------------------- 77
12.8. Panel P.C.B.----------------------------------------------- 77
12.9. D-Amp P.C.B.--------------------------------------------- 78
12.10. SMPS P.C.B.---------------------------------------------- 79
12.11. Tuner P.C.B.----------------------------------------------- 79
12.12. Surround D-Amp P.C.B.-------------------------------- 80
12.13. Mic P.C.B.-------------------------------------------------- 80
12.14. Waveform Table (1/2)----------------------------------- 81
12.15. Waveform Table (2/2)----------------------------------- 82
13 Illustration of ICs, Transistor and Diode---------------- 83
14 Simplified Block Diagram------------------------------------ 85
14.1. Overall Simplified Block Diagram-------------------- 85
14.2. D-Amp Block Diagram---------------------------------- 86
15 Block Diagram--------------------------------------------------- 87
15.1. Servo/System Control ---------------------------------- 87
15.2. IC Terminal Chart (Servo/System Control)-------- 88
15.3. Audio-------------------------------------------------------- 89
15.4. Power Amplifier ------------------------------------------ 90
15.5. Power Supply--------------------------------------------- 92
16 Wiring Diagram-------------------------------------------------- 93
17 Schematic Diagram Notes----------------------------------- 95
18 Schematic Diagram-------------------------------------------- 97
18.1. CD Servo Circuit----------------------------------------- 97
18.2. Main Circuit------------------------------------------------ 98
18.3. Jupiter Circuit--------------------------------------------104
18.4. Panel Circuit ---------------------------------------------108
18.5. CD Open Button, Remote Sensor, Tuner &
Music Port/Headphone Circuit-----------------------110
18.6. D-Amp Circuit-------------------------------------------- 111
18.7. Surround D-Amp Circuit ------------------------------113
18.8. SMPS Circuit---------------------------------------------114
18.9. Mic & Voltage Selector Circuit-----------------------116
19 Printed Circuit Board-----------------------------------------117
19.1. CD Servo, Mic & Voltage Selector P.C.B. --------117
19.2. Main P.C.B.-----------------------------------------------118
19.3. Jupiter P.C.B. --------------------------------------------119
19.4. Panel P.C.B.----------------------------------------------120
19.5. CD Open Button, Remote Sensor, Tuner,
Music Port/Headphone & Surround D-Amp
P.C.B.------------------------------------------------------121
19.6. D-Amp P.C.B.--------------------------------------------122
19.7. SMPS P.C.B.---------------------------------------------123
20 Terminal Function of ICs------------------------------------125
20.1. IC2003 (RFKWMAKX90PH): IC MICRO
PROCESSOR -------------------------------------------125

3
20.2. IC6901(C0HBB0000057): IC FL Driver-----------126
21 Exploded View and Replacement Parts List ---------127
21.1. Exploded View and Mechanical replacement
Part List ---------------------------------------------------127
21.2. Electrical Replacement Part List--------------------133

4
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, carry out the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on
the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the
chassis, the reading should be between 1MΩand 5.2MΩ.
When the exposed metal does not have a return path to the chassis, the reading must be
1.1.2. Leakege Current Hot Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on the set and a
good earth ground such as a water pipe, as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent)
may be used to make the hot checks, leakage current must not exceed 1/2 milliamp. In case a measurement is outside of the
limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is
returned to the customer.
Figure 1
1.2. Before Use
Be sure to disconnect the mains cord before adjusting the voltage selector.
Use a minus(-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will be
used. (If the power supply in your area is 110V ~ 127V or 220V ~ 240V, set to the “110V ~ 127V or 220V ~ 240V” position.)
Note that this unit will be seriously damaged if this setting is not made correctly. (There is no voltage selector for some countries,
the correct voltage is already set.)
1.3. Caution For Fuse Replacement
1.4. Before Repair and Adjustment
Disconnect AC power to discharge unit AC Capacitors as such (C5701, C5703, C5704, C5705, C5706, C5707, C5708) through a
10 Ω, 10 W resistor to ground.
Caution:
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

5
Current consumption at AC 110~127 V / 220~240 V, 50/60 Hz in NO SIGNAL mode volume minimal should be ~ 500 mA.
1.5. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
• No sound is heard when the power is turned on.
• Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
1.6. Safety Parts Information
Safety Parts List:
There are special components used in this equipment which are important for safety.
These parts are marked by in the Schematic Diagrams,Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.
Safet
y
Ref. No. Part No. Part Name & Description Remarks
6 REXX1030 1P RED WIRE (VOLTAGE-SMPS)
7 REXX1031 1P BLACK WIRE (VOLTAGE-SMPS)
13 RGRX1002E-A1 REAR PANEL PH
13 RGRX1002E-B1 REAR PANEL PR
37 RKMX1003-K TOP CABINET
401 RAEX0190Z-V TRAVERSE UNIT
A2 K2CA2YY00039 AC CORD PR
A2 K2CQ2CA00007 AC CORD PH
A3 RQTX1099-M O/I BOOK (En/Sp)
PCB3 REPX0809F SMPS P.C.B. (RTL)
PCB11 REPX0809F VOLTAGE SELECTOR P.C.B. (RTL)
DZ5701 ERZV10V511CS ZNR
S5701 K0ABCA000007 SW VOLTAGE SELECTOR
L5703 G0B932H00002 LINE FILTER
T5701 G4DYZ0000049 SWITCHING TRANSFORMER
T5751 ETS19AB2E6AG SUB TRANSFORMER
T6000 G4DYA0000214 SWITCHING TRANSFORMER
PC5701 B3PBA0000402 PHOTO COUPLER
PC5702 B3PBA0000402 PHOTO COUPLER
PC5720 B3PBA0000402 PHOTO COUPLER
PC5799 B3PBA0000402 PHOTO COUPLER
F1 K5D802BNA005 FUSE
TH5702 D4CAA2R20001 THERMISTOR
TH5860 D4CC11040013 THERMISTOR
TH5900 D4CC11040013 THERMISTOR
P5701 K2AA2B000011 AC INLET
C5701 F0CAF334A105 0.33uF
C5703 F0CAF104A105 0.1uF
C5704 F1BAF1020020 1000pF
C5705 F1BAF1020020 1000pF
C5706 F1BAF1020020 1000pF
C5707 F1BAF1020020 1000pF
C5708 F1BAF1020020 1000pF

6
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive
(ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution:
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).

7
2.2. Precaution of Laser Diode
Caution:
This product utilizes a laser diode with the unit turned “on”, invisible laser radiation is emitted from the pickup lens.
Wavelength: 785 nm (CD)
Maximum output radiation power from pickup: 100 µW/VDE
Laser radiation from the pickup unit is safety level, but be sure the followings:
1. Do not disassemble the pickup unit, since radiation from exposed laser diode is dangerous.
2. Do not adjust the variable resistor on the pickup unit. It was already adjusted.
3. Do not look at the focus lens using optical instruments.
4. Recommend not to look at pickup lens for a long time.

8
2.3. Service caution based on Legal restrictions
2.3.1. General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that
of the normal solder.
Definition of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees
C (662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.
(See right figure)

9
2.4. Handling Precautions for Traverse Unit
The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be
taken avoid caution to electrostatic breakdown when servicing and handling the laser diode in the traverse unit.
2.4.1. Cautions to Be Taken in Handling the Optical Pickup Unit
The laser diode in the optical pickup unit may be damaged due to electrostatic discharge generating from clothes or human body.
Special care must be taken avoid caution to electrostatic discharge damage when servicing the laser diode.
1. Do not give a considerable shock to the optical pickup unit as it has an extremely high-precise structure.
2. To prevent the laser diode from the electrostatic discharge damage, the flexible cable of the optical pickup unit removed
should be short-circuited with a short pin or a clip.
3. The flexible cable may be cut off if an excessive force is applied to it. Use caution when handling the flexible cable.
4. The antistatic FPC is connected to the new optical pickup unit. After replacing the optical pickup unit and connecting the flexi-
ble cable, cut off the antistatic FPC.
2.4.2. Grounding for electrostatic breakdown prevention
Some devices such as the DVD player use the optical pickup (laser diode) and the optical pickup will be damaged by static electric-
ity in the working environment. Proceed servicing works under the working environment where grounding works is completed.
2.4.2.1. Worktable grounding
1. Put a conductive material (sheet) or iron sheet on the area where the optical pickup is placed, and ground the sheet.

10
2.4.2.2. Human body grounding
1. Use the anti-static wrist strap to discharge the static electricity form your body.

11
3 Service Navigation
3.1. Service Information
This service manual contains technical information which will allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service
manual.
•CD Mechanism Unit (DLS6C):
1) This model uses CD Mechanism Unit (DLS6C).
•Micro-processor:
1) The following components are supplied as an assembled part.
- Micro-processor IC, IC2003 (RFKWMAKX90PH)
•Speaker System:
1) This model uses Speaker System, SB-AKX90PH-K.

12
4 Specifications
QAMPLIFIER SECTION
RMS output power stereo mode
Front High Ch (both channels driven)
100 W per channel (5 Ω), 1 kHz, 10% THD
Front Low Ch (both channels driven)
125 W per channel (4 Ω), 1 kHz, 10% THD
Surround Ch 125 W per channel (4 Ω), 1 kHz, 10% THD
Subwoofer Ch 250 W per channel (8 Ω), 100 Hz, 10% THD
Total RMS stereo mode power 1200 W
PMPO output power (For PR only) 13200 W
QFM/AM TUNER, TERMINALS SECTION
Preset station FM 30 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range 87.50 to 108.00 MHz (50 kHz step)
Antenna terminal (s) 75 Ω(unbalanced)
Amplitude Modulation (AM)
Frequency range 522 to 1629 kHz (9 kHz step)
520 to 1630 kHz (10 kHz step)
AUX Input RCA pin jack
Headphone jack
Terminal Stereo,3.5 mm jack
Output level (CD,1 KHz, -20dB) 32 Ω(Max)
Music port (front)
Sensitivity 100 mV, 4.7k Ω
Terminal Stereo.3.5 mm jack
Mic jack
Sensitivity 0.7 mV, 1.1k Ω
Terminal Mono, 3.5 mm jack (1 system)
QDISC SECTION
Discs played (8 cm or 12 cm)
(1) CD-Audio (CD-DA)
(2) CD-R/RW (CD-DA, MP3* formatted disc)
(3) MP3*
*MPEG-1 layer 3,MPEG-2 Layer 3
Pick up
Wavelength 795 nm(CD)
Laser Power CLASS 1 (CD)
Audio output (Disc)
Number of channels 4.2 ch (FL, FR, SL, SR, SWx2)
FL = Front left channel
FR = Front right channel
SL = Surround left channel
SR = Surround right channel
SW = Subwoofer channel
QUSB SECTION
USB Port
USB standard USB 2.0 full speed
Media file format support MP3 (*.mp3)
USB device file system FAT12, FAT16, FAT32
USB Port power 500 mA (max)
Bit Rate 16kbps to 320 kbps (playback)
USB recording
Bit Rate 128 kbps / 192kbps / 320kbps
USB recording speed 1x,4x (CD only)
recording file format MP3 (*.mp3)
Memory section
Memory
Memory size 2 GB
Memory File format MP3 (*.mp3)
Memory recording
Bit Rate 128 kbps / 192 kbps / 320kbps
Memory Recording speed 1x,4x (CD only)
Recording file format MP3 (*.mp3)
Capacity of total song recoreded 1000 song
(Use 128 kbps, approximately 1 song = 4 mins)
QGENERAL
Power supply AC 110 to 127/220 to 240 V, 50/60 Hz
Power Consumption 158 W
Dimensions (W x H x D) 250 mm x 336 mm x 249 mm
Mass 3.6 kg
Operating temperature range 0 °C to +40 °C
Operating humidity range 35% to 80% RH
(no condensation)
PowerConsumptioninstandby
mode 0.3 W (Approximate)
Notes
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
QSystem: SC-AKX90PH-K Main Unit: SA-AKX90PH-K
Speaker system: SB-AKX90PH-K
QSystem: SC-AKX90PR-K Main Unit: SA-AKX90PR-K
Speaker system : SB-AKX90PHK

13
5 Location of Controls and Components
5.1. Main Unit Key Button Operation

14
5.2. Remote Control Key Button Operation

15
5.3. Media Information

16
6 Self-Diagnostic and Special Mode Setting
6.1. Cold-Start
Here is the procedure to carry out cold-start or initialize to shipping mode.
1. Unplug AC power cord
2. Press & hold [POWER] button
3. Plug AC power cord while [POWER] button being pressed
FL Display will show “_ _ _ _ _ _ _ _”
4. Release [POWER] button

17
6.2. Doctor Mode Table
6.2.1. Doctor Mode Table 1
FL Display Key Operation
Front Key
Item
DescriptionMode Name
Doctor Mode
Micro-P Version
Display
Jupiter
Micro-P
Version
To enter into Doctor Mode 1.In CD Mode:
Press [ ] button on main
unit follow by [4] and [7] on
remote control.
2.To exit, press [OK] button on
remote control or press
[POWER, /I] button on main
unit or remote control.
In Doctor Mode:
1.Press [2] button on
remote control.
Display 1:
Display 2:
To check the firmware version
for Jupiter & Microprocessor IC.
Display 1 will display for 2 secs,
followed by display 2.
Micro-processor
Version

18
6.2.2. Doctor Mode Table 2
FL Display Key Operation
Front Key
Item
DescriptionMode Name
Cold Start
Volume Setting
Check
FL Display
Check
To active cold start upon next AC
power up when reset start is execute
the next time.
To check the volume setting of a main
unit.
To check the FL segment display
All segment will light up while all LED
blink at 0.5s,intervals.(if any)
To excute CD OPEN operation.
In Doctor Mode:
1. Press [DISPLAY] button
on remote control.
In Doctor Mode:
1. Press [7],[8],[9],
[PLAY MODE] button on
remote control.
In Doctor mode:
1. Press [1] button on
remote control.
In Doctor mode:
1. Press [DEL] button on
remote control.
Press [7]: VOLUME50
Press [8]: VOLUME35
Press [9]: VOLUME0
Press [PLAY MODE]: VOLUME30
Volume
In this mode, the tray will open &
close.
Note: Refer to Section 6.3 Fig 1 for
process flow.
The counter will
increment by one.
When reach 9999
will change to 0000
DLS6 Reliability
Test (Loading)
CD Open
Check
To determine DLS6
Open/Close operation. In Doctor Mode: 1.Press [>10], follow by [1]
and [1] buttons on remote
control.

19
6.3. Reliability Test Mode (CD Mechanism Unit (DLS6C))
Below is the process flow chart of the aging test for the CD Mechanism Unit (DLS6C).
Fig. 1. Reliability Test (Loading)
OPEN
Operation
OPEN wait
fot 1 s
CLOSE
Operation
CLOSE wait
for 5s Count up

20
6.4. Self-Diagnostic Mode